TILING Lutheran Church of the Holy Spirit

Transcription

1 SECTION TILING PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1. Porcelain tile. 2. Tile backing panels. 3. Metal edge strips. 1.2 SUBMITTALS A. Product Data: For each type of product indicated. B. Samples: 1. Each type and composition of tile and for each color and finish required. 2. Assembled samples, with grouted joints, for each type and composition of tile and for each color and finish required. C. Maintenance data. 1.3 EXTRA MATERIALS A. Furnish extra materials that match and are from same production runs as products installed and that are packaged with protective covering and identified with labels describing contents. 1. Tile and Trim Units: Furnish quantity of full-size units equal to 3 percent of amount installed for each type, composition, color, pattern, and size indicated. PART 2 - PRODUCTS 2.1 TILE PRODUCTS A. ANSI Ceramic Tile Standard: Provide Standard grade tile that complies with ANSI A137.1 for types, compositions, and other characteristics indicated. TILING

2 B. Floor Tile at the Entry Area and the Floors in the Restrooms: 1. Basis-of-Design Product: Subject to compliance with requirements, provide Florida Tile, Livingston porcelain tile. 2. Face Size: 6 x 6 tiles at walls; 13 x 13 tiles at floors. 3. Thickness: 3/8 4. Finish: Matte 5. Tile Color and Pattern: Assume 1/2 #9117P Greige ; 1/2 #9192P Leather. 6. Grout Color: PTS Group 7. Trim Units: Coordinated with sizes and coursing of adjoining flat tile where applicable and matching characteristics of adjoining flat tile. C. Floor Tile Accents at Walls in the Restroom Areas: 1. Basis-of-Design Product: Subject to compliance with requirements, provide Florida Tile Legend No /M122 Magna. 2. Face Size: 2 x 2 3. Thickness: 3/8 4. Finish: Matte 5. Tile Color and Pattern: To be selected from manufacturer s full line of colors. 6. Grout Color: PTS Group 7. Trim Units: Coordinate the sizes of the flooring and coursing with the patterns indicated on the drawings for the project. 2.2 SETTING MATERIALS A. Latex-Portland Cement Mortar (Thin Set): ANSI A Manufacturers: Subject to compliance with requirements, available manufacturers offering products that may be incorporated into the Work include, but are not limited to, the following: a. C-Cure. b. Laticrete International, Inc. c. MAPEI Corporation. d. Summitville Tiles, Inc. 2. Prepackaged, dry-mortar mix combined with liquid-latex additive. 3. For wall applications, provide nonsagging mortar. TILING

3 2.3 GROUT MATERIALS A. Polymer-Modified Tile Grout: ANSI A Manufacturers: Subject to compliance with requirements, available manufacturers offering products that may be incorporated into the Work include, but are not limited to, the following: a. PTS Group b. C-Cure. c. Laticrete International, Inc. d. MAPEI Corporation. e. Summitville Tiles, Inc. 2. Polymer Type: Liquid-latex form for addition to prepackaged dry-grout mix. B. Water-Cleanable Epoxy Grout: ANSI A Manufacturers: Subject to compliance with requirements, available manufacturers offering products that may be incorporated into the Work include, but are not limited to, the following: a. PTS Group b. C-Cure. c. Laticrete International, Inc. d. MAPEI Corporation. e. Summitville Tiles, Inc. 2.4 ELASTOMERIC SEALANTS A. General: Provide sealants, primers, backer rods, and other sealant accessories that comply with the following requirements and with the applicable requirements in Division 07 Section "Joint Sealants." 1. Use sealants that have a VOC content of 250 g/l or less when calculated according to 40 CFR 59, Subpart D (EPA Method 24). B. One-Part, Mildew-Resistant Silicone Sealant: ASTM C 920; Type S; Grade NS; Class 25; Uses NT, G, A, and, as applicable to nonporous joint substrates indicated, O; formulated with fungicide, intended for sealing interior ceramic tile joints and other nonporous substrates that are subject to in-service exposures of high humidity and extreme temperatures. 1. Products: Subject to compliance with requirements, available products that may be incorporated into the Work include, but are not limited to, the following: a. DAP Inc.; 100 percent Silicone Kitchen and Bath Sealant. b. Dow Corning Corporation; Dow Corning 786. c. GE Silicones, a division of GE Specialty Materials; Sanitary d. Laticrete International, Inc.; Latasil Tile & Stone Sealant. TILING

4 e. Pecora Corporation; Pecora 898 Sanitary Silicone Sealant. f. Tremco Incorporated; Tremsil 600 White. C. Multipart, Pourable Urethane Sealant for Use T: ASTM C 920; Type M; Grade P; Class 25; Uses T, M, A, and, as applicable to joint substrates indicated, O. 1. Products: Subject to compliance with requirements, available products that may be incorporated into the Work include, but are not limited to, the following: a. Bostik, Inc.; Chem-Calk 550. b. Degussa Building Systems; Sonneborn Sonolastic SL 2. c. Pecora Corporation; NR-200 Urexpan. d. Sika Corporation; Sikaflex-2c SL. e. Tremco Incorporated.; THC MISCELLANEOUS MATERIALS A. Trowelable Underlayments and Patching Compounds: Latex-modified, portland cement-based formulation provided or approved by manufacturer of tile-setting materials for installations indicated. B. Metal Edge Strips: Angle or L-shape, nickel silver exposed-edge material. 1. Basis-of-Design: Schluter C. Grout Sealer: Manufacturer's standard silicone product for sealing grout joints and that does not change color or appearance of grout. 1. Products: Subject to compliance with requirements, available products that may be incorporated into the Work include, but are not limited to, the following: a. C-Cure; Penetrating Sealer 978. b. MAPEI Corporation; KER 003, Silicone Spray Sealer for Cementitious Tile Grout c. Southern Grouts & Mortars, Inc.; Silicone Grout Sealer. d. Summitville Tiles, Inc.; SL-15, Invisible Seal Penetrating Grout and Tile Sealer. e. TEC, a subsidiary of H. B. Fuller Company; TA-256 Penetrating Silicone Grout Sealer. PART 3 - EXECUTION 3.1 EXAMINATION A. Examine substrates, areas, and conditions where tile will be installed, with Installer present, for compliance with requirements for installation tolerances and other conditions affecting performance of installed tile. 1. Verify that substrates for setting tile are firm, dry, clean, free of coatings that are incompatible with tile-setting materials including curing compounds and other substances TILING

5 that contain soap, wax, oil, or silicone; and comply with flatness tolerances required by ANSI A for installations indicated. 3.2 PREPARATION A. Fill cracks, holes, and depressions in concrete substrates for tile floors installed with thin-set mortar with trowelable leveling and patching compound specifically recommended by tilesetting material manufacturer. B. Blending: For tile exhibiting color variations, use factory blended tile or blend tiles at Project site before installing. C. Field-Applied Temporary Protective Coating: If indicated under tile type or needed to prevent grout from staining or adhering to exposed tile surfaces, precoat them with continuous film of temporary protective coating, taking care not to coat unexposed tile surfaces. 3.3 INSTALLATION A. Comply with TCA's "Handbook for Ceramic Tile Installation" for TCA installation methods specified in tile installation schedules. Comply with parts of the ANSI A108 Series "Specifications for Installation of Ceramic Tile" that are referenced in TCA installation methods, specified in tile installation schedules, and apply to types of setting and grouting materials used. 1. For the following installations, follow procedures in the ANSI A108 Series of tile installation standards for providing 95 percent mortar coverage: a. Tile floors in wet areas. b. Tile floors composed of tiles 12 by 12 or larger. c. Tile floors composed of rib-backed tiles. B. Extend tile work into recesses and under or behind equipment and fixtures to form complete covering without interruptions unless otherwise indicated. Terminate work neatly at obstructions, edges, and corners without disrupting pattern or joint alignments. C. Accurately form intersections and returns. Perform cutting and drilling of tile without marring visible surfaces. Carefully grind cut edges of tile abutting trim, finish, or built-in items for straight aligned joints. Fit tile closely to electrical outlets, piping, fixtures, and other penetrations so plates, collars, or covers overlap tile. D. Jointing Pattern: Lay tile in grid pattern unless otherwise indicated. Lay out tile work and center tile fields in both directions in each space or on each wall area. Lay out tile work to minimize the use of pieces that are less than half of a tile. Provide uniform joint widths unless otherwise indicated. E. Joint Widths: Unless otherwise indicated, install tile with the following joint widths: 1. Paver Tile: 1/8 2. Wall & Floor Tile: 1/8 TILING

6 F. Lay out tile wainscots to dimensions indicated or to next full tile beyond dimensions indicated. G. Expansion Joints: Provide expansion joints and other sealant-filled joints, including control, contraction, and isolation joints, where indicated and as recommended by TCA. Form joints during installation of setting materials, mortar beds, and tile. Do not saw-cut joints after installing tiles. 1. Where joints occur in concrete substrates, locate joints in tile surfaces directly above them. 2. Prepare joints and apply sealants to comply with requirements in Division 07 Section "Joint Sealants." H. Metal Edge Strips: Install where exposed edge of tile flooring meets carpet, wood, or other flooring that finishes flush with or below top of tile and no threshold is indicated. I. Grout Sealer: Apply grout sealer to grout joints in tile floors according to grout-sealer manufacturer's written instructions. As soon as grout sealer has penetrated grout joints, remove excess sealer and sealer from tile faces by wiping with soft cloth. J. Install cementitious backer units or fiber-cement underlayment and treat joints according to ANSI A and manufacturer's written instructions for type of application indicated. Use latex-portland cement mortar for bonding material unless otherwise directed in manufacturer's written instructions. END OF SECTION TILING