TION & FLOOR LEVELING PROUDLY PROUDLY PROUDLY CANADIAN CANADIAN CANADIAN

Transcription

1 RESTORATION & FLOOR LEVELING Patching and Smoothing Self-Leveling Primers Concrete and Repair Mortars Smooth Concrete Resurfacing Protective Coatings Specialty Products COMMERCIAL

2 PATCHING AND SMOOTHING SOLHYDFINISH FAST SETTING PATCHING COMPOUND FOR THIN REPAIRS Thin coating and smoothing of floors to accept various floor coverings. SOLHYDFINISH is a cement based, rapid setting, trowel applied patching compound used to smooth subfloors prior to the installation of finished floor coverings. SOLHYDFINISH has a creamy consistency, exceptional coverage, tenacious bond and can be applied very thin. SOLHYDFINISH allows for the installation of many floor coverings in as little as 25 to 30 minutes. Smoothing of damaged, cracked, uneven concrete floors and other imperfections Smoothing of small surface imperfections with thin applications of SOLHYDFINISH from 0 to 14 mm (1/2 ) in one single operation without cracking Can receive floor coverings such as vinyl tile, ceramic, carpets in as little as 25 to 30 minutes and even epoxy coatings 2 hours after its application Can be applied over non-water soluble adhesive and properly prepared cutback residue that are sound and well adhered to substrate No Priming required Mixing with water only Fast setting Exceptional coverage Can be retempered (mixed) without the addition of water Environmentally friendly - Contributes points to LEED Certified Projects SOLHYDPATCH FAST SETTING POLYMER MODIFIED CEMENT BASED PATCHING COMPOUND Patching and repair of damaged surfaces and uneven floors. SOLHYDPATCH is a quick setting cement based polymer modified patching compound for repairing and leveling floors prior to the installation of floor coverings. SOLHYDPATCH allows a hard, smooth troweled surface to be easily achieved. Ideal for screeding, ramping, patching & skimcoating Filling holes, cracks, voids prior to the installation of floor coverings Repairing and leveling of rough, uneven concrete and wood floor surfaces Easy to use Excellent bond to concrete Install floor covering in as little as 1 to 2 hours after application Can be applied from featheredge to 50 mm (2 ) neat Compatible with all adhesives approved for concrete Excellent yield Up to 2.12 m² (22 ft²) per bag at a thickness of 3 mm (1/8 ) 11.3 kg (25 lbs) bag Up to 9.2 m 2 (99 ft 2 ) per bag at a thickness of 1 mm (1/32 ) 4.5 kg (10 lbs) bag 2

3 SELF-LEVELING UNDERLAYMENT SOLHYDFLOW FS SMOOTH AND DURABLE SELF-LEVELING Specially designed for interior use in leveling uneven rough damaged, unfinished, frozen or rained on concrete slabs. Provides a smooth and even finish to existing wooden, vinyl tiles, ceramic or terrazzo floors. SOLHYDFLOW FS is a self-leveling underlayment that provides a flat, smooth, durable surface with minimum effort, installation time and cost. It is a single component, high strength, non-shrink, regulated setting underlayment using a polymer modified binder system to level and smooth floors. SOLHYDFLOW FS can be poured or pumped (no trowel required) in one single step to thicknesses from 3 mm (1/8 ) to 100 mm (4 )* (Refer to Product Application section). SOLHYDFLOW FS will accept foot traffic within 3 to 4 hours and floor coverings 16 hours after application. Floors covered by carpeting, hardwood, tiles, VFT or polymer coatings Office and condo building floors, shopping center and gymnasium floors Heated flooring Economical and easy to use Self-leveling, no trowel work required Installable from 3 mm (1/8 ) to a 100 mm (4 ) thickness Ideal for pouring and pumping Maintains workability for 25 to 35 minutes at 21ºC (70ºF) No sanding or grinding required Covers approximately 4.1 m 2 (44 ft 2 ) per bag at a thickness of 3 mm (1/8 ) 22.7 kg (50 lbs) bag SOLHYDFLOW SUPREME PREMIUM SMOOTH AND DURABLE SELF-LEVELING Self leveling underlayment specially designed for very thin leveling of rough, unfinished or damaged interior concrete floors. Provides a perfectly flat, smooth, durable surface to existing concrete, wooden, vinyl tiled, ceramic or terrazzo floors. SOLHYDFLOW SUPREME is a self-leveling fluid underlayment that provides a flat, smooth, durable surface with minimum effort, installation time and cost. It is a single component, high strength, nonshrink, regulated setting underlayment using a polymer modified binder system to level and smooth floors. SOLHYDFLOW SUPREME can be poured or pumped (no trowel required) in one single step to thicknesses from 2 mm (3/32 ) to 37 mm (1½ ). SOLHYDFLOW SUPREME will accept foot traffic in 3 hours and floor coverings in 12 hours after application. Floors covered by carpeting, hardwood, tiles, VFT or polymer coatings Office and condo building floors, shopping center and gymnasium floors Heated flooring Economical and easy to use Self-leveling, no trowel work required Installable from featheredge to a 37 mm (1½ ) thickness Very fluid, ideal for pouring and pumping Maintains workability for 25 minutes at 21ºC (70ºF) No sanding or grinding required Covers approximately 5.6 m 2 (60 ft 2 ) per bag at a thickness of 3 mm (1/8 ) 22.7 kg (50 lbs) bag 3

4 SELF-LEVELING UNDERLAYMENT SOLHYDFLOW SUPREME PLUS Specially designed for the leveling and smoothing of uneven interior concrete floors which are damaged by freeze-thaw during curing. Leveling of existing plywood, vinyl tile, ceramic or terrazzo floors. SOLHYDFLOW SUPREME PLUS is a very fluid self-leveling underlayment to obtain a level, smooth and durable surface at a low handling and installation cost with minimum effort. It is a rapid setting, high strength, one component, non-shrink product using a polymer modified binder for smoothing and leveling floor surfaces. SOLHYDFLOW SUPREME PLUS can be poured or pumped at thicknesses from 2 mm (1/16 ) to 37 mm (1-1/2 ) in one step operation. We can walk on the surface after 3 hours and the surface can receive coverings 12 hours after the installation. Surfaces to be covered by carpet, hardwood, ceramic, Vinyl Tile (VTF) or polymers. Show room Floors Office and condo buildings School and gymnasium floors Hospital and correctional facilities Heated Flooring YIELD Covers approximately 4.54 m2 (50 sq.ft.) per bag at a 3 mm thickness (1/8 ) kg bags (50 lbs.) 4

5 SELF-LEVELING WEAR SURFACE SOLHYDFLOW DECO SELF-LEVELING DECORATIVE TOPPING Specially designed fast setting selfleveling wear surface for the repair and the levelling of concrete floors that are uneven rough damaged, unfinished, frozen or rained on concrete slabs. Provides a smooth and even finish to existing wooden, vinyl tile, ceramic or terrazzo floors. SOLHYDFLOW DECO is a self-leveling wear surface that provides a flat, smooth, durable surface with minimum effort, installation time and cost. It can be used for decorative and industrial indoor flooring applications and can be incorporated with integral color, colored aggregates and unique surface treatments. It is a single component, high strength, non-shrink, regulated setting topping using a polymer modified binder system to level and smooth floors. SOLHYDFLOW DECO can be poured or pumped (no trowel required) in one single step to thicknesses from 6 mm (1/4 ) to 50 mm (2 ). SOLHYDFLOW DECO will accept foot traffic within 3 hours and floor treatments 18 hours after application. Office and condo building floors Heated flooring Can be stained, polished and lightly grinded Can be coated with polyurethane or epoxy within 18 hours Economical and easy to use, mixes with water only Self-leveling, no trowel work required, ideal for pouring and pumping Installable from 6 mm (1/4 ) to a 50 mm (2 ) thickness Maintains workability for 25 minutes at 21ºC (70ºF) Covers approximately 2.0 m 2 (22 ft 2 ) per bag at a thickness of 6 mm (1/4 ) 22.7 kg (50 lbs) bag SOLHYDFLOW INDUSTRIAL HEAVY DUTY SELF-LEVELING WEAR RESISTANT TOPPING Specifically designed fast setting self-leveling wear surface for the repair and the levelling of concrete plant floors that are uneven rough damaged, unfinished, frozen or rained on concrete slabs. Specially formulated for heavy duty industrial equipment traffic on concrete floors. SOLHYDFLOW INDUSTRIAL TM is a heavy duty self-leveling wear resistant topping that provides a flat, smooth and very durable surface with minimum effort, installation time and cost. It is a single component, high strength, nonshrink, regulated setting wear surface using a polymer modified binder system to level and smooth floors. SOLHYDFLOW INDUSTRIAL TM can be poured or pumped (smoothing of surface may be required) in one single step to thicknesses from 6 mm (1/4 ) to 20 mm (3/4 ). SOLHYDFLOW INDUSTRIAL TM will accept foot traffic within 4 hours and heavy industrial traffic 24 hours after application. Plants(warehouse and distribution) floors Parking garage floors (interior) Showrooms (Heavy equipment vehicle dealers) Installable from 6 mm (1/4 ) to a 20 mm (3/4 ) thickness Self-leveling wear surface ideal for pouring and pumping Maintains workability for 25 to 35 minutes at 21ºC (70ºF) Minimize shut down time and accelerates the return to service of the floors Yield can be increased with additional approved aggregate Covers approximately 2.0 m 2 (22 ft 2 ) per bag at a thickness of 6 mm (1/4 ) 22.7 kg (50 lbs) bag 5

6 PRIMERS SOLHYDFLOW PRIMER PLUS PREMIUM ACRYLIC BASED BONDING AGENT AND PRIMER Specially designed primer for various substrates to receive SOLHYDFLOW self-leveling products. SOLHYDFLOW PRIMER PLUS is a premium concentrated acrylic primer designed for interior & exterior applications on structurally sound, clean concrete. In addition to concrete on interior applications SOLHYDFLOW PRIMER PLUS can be used over wood, well bonded VCT/VAT, cutback and other adhesive residues not affected by water. Gypsum underlayment, terrazzo, epoxy floor coatings, ceramic, quarry tile, copper, lead and properly treated steel can also be primed with SOLHYDFLOW PRIMER PLUS. Its unique ability to bond to both porous and non-porous substrates makes it ideal for varying jobsite conditions. SOLHYDFLOW PRIMER PLUS is easy to use, creates a tenacious bond to the substrate and reduces surface porosity. Can be roller or broom applied depending on application Non-flammable, non-toxic, non-explosive Water based and VOC compliant Excellent on very porous concrete surfaces High solids content, solvent free Low particle size for excellent penetration Tenacious bond strength to a variety of surfaces (ON VERY POROUS CONCRETE SURFACE IN 2 COATS) First coat: diluted 1:3 with water covers approximately 23.2 m 2 (250 ft 2 ) Second coat: diluted 1:1 with water covers approximately 37.2 m 2 (400 ft 2 ) SOLHYDPRIME 100 HIGH PERFORMANCE EPOXY PRIMER SOLHYDPRIME 100 is used as an epoxy primer for epoxy coatings, epoxy troweled mortars, epoxy linings, flexible epoxy membranes, self-consolidating concretes and cement based self-leveling products. SOLHYDPRIME 100 is a 100% solids, moisture tolerant epoxy primer formulated for toughness and stress relieving properties. The combination of high tensile strength and tensile elongation provide for greater durability under impact and thermally-induced stresses. SOLHYDFLOW cement based self-leveling products 100% solids May be applied to damp surfaces (moisture tolerant) Provides chemical resistance Relieves stress due to low modulus of elasticity Improves overall bond strength of mortars and self-leveling systems (ON VERY POROUS CONCRETE SURFACE IN 2 COATS) For 2 units of 3.8 L (2 X 1 US gal) of Part A mixed with 1 unit of 3.8 L (1 US gal) of Part B at 4 mil. (DFT and WFT) 9.8 m 2 (105.9 ft 2 ) Part A: 2 units of 3.8 L (2 X 1 US gal) Part B: 1 unit of 3.8 L (1 US gal) 18.9 kg (5 US gal) pail and 3.8 L (1 US gal) bottle 6

7 CONCRETE AND REPAIR MORTARS SOLHYDCRETE HIGH STRENGTH RAPID SETTING CONCRETE FOR DEEP REPAIRS Interior vertical (formwork) and horizontal deep repairs and leveling. SOLHYDCRETE is a fast setting, high strength repair concrete that produces a rapid and permanent repair for existing damaged concrete. It is dimensionally stable and forms an integral bond with the existing concrete to restore its structural integrity. SOLHYDCRETE can be placed at thicknesses ranging from 13 mm to 300 mm in one single operation. Repair sloping and leveling of concrete surfaces prior to the application of SOLHYDFLOW self-leveling products Quick repair and turnaround of industrial floors which can be put in service in 3 hours after application Permanent repair of concrete May be placed at variable thickness Wear resistant Economic and easy to install Easily applied with a steel trowel Covers approximately 1m² (11 ft²) per bag at a thickness of 12.5 mm (1/2 ) 22.7 kg (50 lbs) bag 7

8 CONCRETE AND REPAIR MORTARS STRUCTUROC H HIGH STRENGTH RAPID SETTING MORTAR FOR HORIZONTAL REPAIRS Repair of spalled and damaged concrete floors due to wear, abrasion, temperature and other damage factors. STRUCTUROC H is a rapid setting, high early strength repair mortar that produces a fast, permanent repair of concrete. STRUCTUROC H is dimensionally stable, shrinkage and crack resistant and forms an integral bond with the existing concrete to restore its structural integrity. STRUCTUROC H is designed for horizontal repairs and can be placed at thicknesses ranging from 6 mm (1/4 ) up to 300 mm (12 ) in a single lift. This product can be extended with up to 50% of clean dry 10 mm (3/8 ) granitic or clean pea gravel aggregate to then produce a rapid setting concrete for repair. Deep repairs to concrete floors prior to the installation of SOLHYDFLOW self-leveling products Repair and creation of concrete slopes, drains and trenches Repair of concrete walls, bases and columns Meets or exceeds requirements of ASTM C928/C928M-09 Permanent repair of concrete Excellent bond strength Freeze/thaw resistant Extremely resistant to wear and abrasion Rapid and early strength No bonding agent required Can be overcoated within 6 hours after placement Covers approximately 1.9 m 2 (20 ft 2 ) per bag at a thickness of 6 mm (1/4 ) STRUCTUROC H ULTRA HIGH STRENGTH RAPID SETTING FLOWABLE MORTAR FOR HORIZONTAL REPAIRS Repair of spalled and damaged concrete floors due to wear, abrasion, temperature and other damage factors. STRUCTUROC H ULTRA is a rapid setting, high early strength repair mortar that produces a fast, permanent repair of concrete. STRUCTUROC H ULTRA is dimensionally stable, shrinkage and crack resistant and forms an integral bond with the existing concrete to restore its structural integrity. STRUCTUROC H ULTRA is designed for horizontal repairs and can be placed at thicknesses ranging from 3 mm (1/8 ) up to 50 mm (2 ) in a single lift. This product can be extended with up to 50% of clean dry granitic or clean pea gravel aggregate to then produce a rapid setting concrete for repair. Deep repairs to concrete floors prior to the installation of SOLHYDFLOW self-leveling products Repair and creation of concrete slopes, drains and trenches Repair of concrete walls, bases and columns Repair of balconies Easy to pump & pour and easy to finish Meets or exceeds requirements of ASTM C928/C928M-09 Freeze/thaw resistant Can be overcoated within 6 hours after placement Covers approximately 1.9 m 2 (20 ft 2 ) per bag at a thickness of 6 mm (1/4 ) 22.7 kg (50 lbs) bag and 4.5 kg (10 lbs) pail 8

9 CONCRETE AND REPAIR MORTARS STRUCTUROC V HIGH STRENGTH RAPID SETTING MORTAR FOR VERTICAL REPAIRS All vertical or overhead repairs. STRUCTUROC-V is a cement based, one component, polymer modified, high strength, shrinkage compensated rapid setting repair mortar. It is designed for vertical and overhead concrete repairs to produce superior bond, tensile and flexural strength. STRUCTUROC V is able to be placed and sculpted to proper shape in one operation for thicknesses from 5 mm (1/4 ) to 50 mm (2 ). Bridges, viaducts and tunnels Parapets, columns and beams repairs Single component Tenacious bond strength High early and ultimate compressive and flexural strength Rapid setting Can be overcoated within 8 hours after placement Easily applied with a trowel Covers approximately 2.0 m 2 (22 ft 2 ) per bag at a thickness of 6 mm (1/4 ) 22.7 kg (50 lbs) bag STRUCTUROC V PLUS RAPID SETTING MORTAR FOR VERTICAL REPAIRS All vertical or overhead repairs. STRUCTUROC V PLUS is a cement based, two components, polymer modified, shrinkage compensated rapid setting repair mortar. Designed for vertical and overhead concrete repairs. STRUCTUROC V PLUS is able to be easily placed an sculpted to proper shape at thicknesses from 5 mm (1/4 ) and exceeding to 50 mm (2 ) in one single operation. Bridges, viaducts and tunnels Parapets, columns and beams repairs Two (2) components Easily placed Can be overcoated within 12 hours after placement Covers approximately 2.0 m 2 (22 ft 2 ) per bag at a thickness of 6 mm (1/4 ) when mixed with 3.8 L (0.87 to 1 US gal) of V PLUS LIQUID POLYMER 22.7 kg (50lbs) bag of STRUCTUROC V PLUS and 3.8 L (1 US gal) bottle of V PLUS LIQUID POLYMER 9

10 COATINGS SPEC-COAT EPOXY CLEAR SOLVENT-FREE EPOXY POLYMER WITH HIGH ABRASION AND CHEMICAL RESISTANCE Specially designed multifunctional epoxy resin system which can be used as a primer, smooth surface coating, textured coating, self leveling broadcast system and trowel applied system. SPEC-COAT EPOXY CLEAR is a 100% solids epoxy polymer system with excellent all around application properties. Either as a stand-alone coating or as a binder for various SPEC-COAT and SOLHYDTOP systems, it provides high abrasion resistance and good chemical resistance. With no solvent present in the formula, SPEC-COAT EPOXY CLEAR complies with strictest V.O.C. regulations while offering extremely low odor levels during product installation. Contains no solvents No harmful odors during application Will not contaminate foods because of absence of V.O.C. Fast curing Excellent wear and abrasion resistance Excellent durability, providing up to 3 to 5 times the life expectancy of conventional coatings Primer 5m²/L (200 ft²/gal) (approx. rate) Smooth Surface Coating Prime Coat: 5 m²/l (200 ft²/gal) Top Coat: 3.25 m²/l (133 ft²/gal) Textured Coating Prime Coat: 5 m²/l (200 ft²/gal) Top Coat: 3.25 m²/l (133 ft²/gal) of Solhydcoat Thixo Self Leveling Broadcast System Prime Coat: 5 m²/l (200 ft²/gal) Base Coat: 1 m²/l (40 ft²/gal) Broadcast Silica Sand or selected broadcast material to saturation. Top Coat: 4 m²/l (160 ft²/gal) Trowel Applied System Prime Coat: 5 m²/l (200 ft²/gal) Screed Mortar: Mix SOLHYDCOAT EPOXY CLEAR with STRUCTUROC HCR-F part C (small aggregate) to a mortar consistency. Apply at a thickness of 6 mm (¼ ). Top Coat: 4 m²/l (160 ft²/gal) SPEC-COAT URETHANE TWO COMPONENT POLYURETHANE BASED COATING Specially designed for sealing of concrete surfaces to protect against weathering, ultra-violet rays, abrasion and certain aggressive chemical products. SPEC-COAT URETHANE is a two component catalyzed polyurethane based coating for interior or exterior applications with an excellent durability, good color stability, while maintaining its long term lustre with a good resistance to weathering and dulling. SPEC-COATURETHANE s exceptional resistance to abrasion, to impacts and weathering makes it ideal for many industrial, commercial and institutional applications. Excellent resistance to deterioration caused by exposure to ultra-violet rays Excellent resistance to wear and abrasion Maintains its lustre in the long term Good chemical resistance Coverage per 11.5 L units is 69 m² at a nominal thickness of 3 mils L units, 50 units per skid L (15 US gal) per unit 10

11 ASPHALT REPAIR MORTARS TOP-MIX HIGH PERFORMANCE COLD MIX ASPHALT Top-Mix by Tech-Mix is stable, high performance cold mix asphalt. Offers good workability at low temperatures and outstanding bond in damp conditions. Top-Mix is composed of more than 75% reclaimed materials. Repairing potholes, trenches and curbs Maintenance of indoor and outdoor parking areas Winter and wet weather repairs Covers approximately m 3 (0.283 ft 3 ) per 22.7 kg bag and m 3 (0.374 ft 3 ) per 30 kg bag Covers approximately m 2 (1.73 ft 2 ) per 22.7 kg bag and m 2 (2.28 ft 2 ) per 30 kg bag for a hole with a depth of 5 cm (2 ) 22.7 kg and 30 kg bulk or bags 11

12 REPAIR AND REHABILITATION INJECTION EPOXY / POLYURETHANE WATERPROOFING AND SEALING CONCRETE PROBLEMS Porosity Shrinkage / Cracking Abrasion / Erosion Temperature Corrosion Slope / Levelling Adhesion Flex / Shear Freeze-Thaw CORROSION PROTECTION REINFORCING WITH FRP The Convenient Long-Life Cold Patch Asphalt SOLUTIONS Manufacturing Formulations R&D Quality Control Recommendations Sales-Logistics Equipment Service Technique Training SPEC-ROC TECHNOLOGIES 158 Fife Rd, unit 22, Guelph, Ontario N1H 0B inquiries@specroc.ca 295 Leroux, Chelmsford, Ontario P0M 1L0