DETAIL DRAWINGS GENERAL NOTES. The technical data provided in this communication is for information purposes only.

Transcription

1 DETAIL DRAWINGS shaping roofs

2 DETAIL DRAWINGS GENERAL The technical data provided in this communication is for information purposes only. The following detail drawings represent suggestions for standard roof structure design and must be adapted by the addressee according to actual construction conditions. The design of these types of roof structure requires careful planning and calculation based on the actual conditions. The choice and use of proper fixed points and screws must be made in accordance with the static calculations. ISCOM SPA provides this information based on its experience and knowledge and accepts no liability for any loss, damage, costs or expense incurred in relation to or arising from any person relying on the suggestions and information rendered. All information issued by ISCOM SPA is subject to continuous development without notification. The information/details contained in this communication are correct at the date of issue. It is the addressee's responsibility to ascertain from ISCOM SPA that the information contained in this communication has not changed at the time of use by the addressee. riverclack 01

3 DUO PITCH RIDGE 05 MONO PITCH RIDGE 11 VERGE DETAILS 19 EAVES DETAILS 25 EXPANSION JOINTS 35 ROOF PENETRATION 39 SKYLIGHTS 41 OVERLAP DETAILS 49 CURVED ROOF RIDGE 53 DIAGONAL ROOF RIDGE 55 riverclack 03

4 DUO PITCH RIDGE DETAIL S NOTCHED PLATE RA130 RIDGE FLASHING RA180 RIDGE BRACKET RA150 FIXED POINT BLOCK RA110 RIDGE CLOSURE RA170 min.50 / max.80 mm RIDGE BLOCK FILLER BLOCK RA140 A-A mm 225 / mm 287 SLOPE <6% RIDGE BRACKET RA150 RIDGE FLASHING RA180 RIVERCLACK CLIP SCREW FIXED POINT BLOCK RA110 RIDGE CLOSURE RA170 RIDGE BLOCK SECTION A-A FILLER BLOCK RA140 - Slope < 6% - If length of sheet > 20m use item RA120 as fixed point according to instructions or use two RA110 (up to max length 40m) according to instructions 04 riverclack 05

5 DUO PITCH RIDGE DETAIL S RIDGE BRACKET RA157 RIDGE BLOCK min.50 / max.80 mm RIDGE CLOSURE RA170 RIDGE FLASHING RA180 FILLER BLOCK RA140 A-A mm 225 / mm 287 SLOPE >6% RIDGE BRACKET RA157 RIDGE FLASHING RA180 RIVERCLACK CLIP SCREW RIDGE CLOSURE RA170 FILLER BLOCK RA140 SECTION A-A - Slope > 6% - As ridge bracket RA157 is also a fixed point use it according to instructions 06 riverclack 07

6 DIAGONAL ROOF RIDGE DETAIL S SECTION A-A FILLER BLOCK RA140 RIDGE BLOCK min.50 / max.80 mm mm 225 / mm 287 RIDGE BRACKET RA157 RIDGE FLASHING RA180 RIVERCLACK CLIP SLOPE >6% RIDGE CLOSURE RA170 A-A RIDGE FLASHING RA180 RIDGE CLOSURE RA170 RIDGE BRACKET RA157 A-A FILLER BLOCK RA riverclack 09

7 MONO PITCH RIDGE DETAIL S RIDGE BRACKET RA150 FLASHING RIDGE CLOSURE RA170 FLASHING SUPPORT RIDGE BLOCK RIDGE FLASHING FILLER BLOCK RA140 SLOPE >6% min. 25 mm min.160 / max.200 mm - Slope > 6% - If length of sheet > 20m use item RA120 as fixed point according to instructions or use two RA110 (up to max length 40m) according to instructions 10 riverclack 11

8 MONO PITCH RIDGE DETAIL S NOTCHED PLATE RA130 RIDGE BRACKET RA150 FILLER BLOCK RA140 FIXED POINT BLOCK RA110 RIDGE FLASHING RA180 min.160 / max.200 mm SLOPE <6% min. 25 mm - Slope < 6% - If length of sheet > 20m use item RA120 as fixed point according to instructions or use two RA110 (up to max length 40m) according to instructions 12 riverclack 13

9 MONO PITCH RIDGE DETAIL S RIDGE FLASHING RA180 NOTCHED PLATE RA130 RIDGE BRACKET RA150 RIDGE CLOSURE RA170 RIDGE BLOCK FILLER BLOCK RA140 min.160 / max.200 mm FIXED POINT BLOCK RA110 SLOPE <6% - Slope < 6% - If length of sheet > 20m use item RA120 as fixed point according to instructions or use two RA110 (up to max length 40m) according to instructions 14 riverclack 15

10 MONO PITCH RIDGE DETAIL S RIDGE FLASHING RA180 RIDGE BRACKET RA150 RIDGE CLOSURE RA170 RIDGE BLOCK FILLER BLOCK RA140 min.160 / max.200 mm FIXED POINT BLOCK RA110 SLOPE >6% - Slope > 6% - If length of sheet > 20m use item RA120 as fixed point according to instructions or use two RA110 (up to max length 40m) according to instructions 16 riverclack 17

11 PARAPET VERGE DETAIL S CLOSURE FLASHING EAVE BLOCK min.90 / max.350 mm 18 riverclack 19

12 PARAPET VERGE DETAIL S FLASHING FLASHING SUPPORT DECORATIVE PANEL VERGE FLASHING SIDE CLOSURE RA175 VERGE FLASHING BRACKET RA riverclack 21

13 OVERHANGING VERGE DETAIL S VERGE FLASHING SIDE CLOSURE RA175 VERGE FLASHING BRACKET RA riverclack 23

14 EAVES GUTTER DETAIL S STIFFENING PROFILE RA181 GUTTER BRACKET EAVE BLOCK max.220 mm CLOSURE PROFILE 24 riverclack 25

15 PARAPET EAVES GUTTER DETAIL S EAVE BLOCK DRIP FLASHING FLASHING FLASHING SUPPORT RIGID INSULATION max.220 mm GUTTER UNDER GUTTER PROFILE 26 riverclack 27

16 VALLEY GUTTER DETAIL S EAVE BLOCK RIGID INSULATION max.220 mm DRIP FLASHING GUTTER UNDER GUTTER PROFILE 28 riverclack 29

17 INTERMEDIATE GUTTER DETAIL S DRIP FLASHING FIXED POINT BLOCK RA110 FILLER BLOCK RA140 EAVE BLOCK RIDGE BRACKET RA150 max 220 mm NOTCHED PLATE RA130 FLASHING min.160 / max.200 mm GUTTER RIGID INSULATION UNDER GUTTER PROFILE - Mono ridge type considered on this sheet is one of the available options. Please consider proper type according to actual slope. 30 riverclack 31

18 BULLNOSE DETAIL S max. 220 mm DRIP FLASHING GUTTER EAVE BLOCK SUPPORT PROFILE 32 riverclack 33

19 EXPANSION JOINT DETAIL S FLASHING FLASHING SUPPORT EAVE BLOCK min.90 / max.350 mm CLOSURE PROFILE - Expansion joint has to be calculated according to actual thermal movement 34 riverclack 35

20 EXPANSION JOINT DETAIL S FLASHING SIDE CLOSURE RA175 FLASHING SUPPORT CLOSURE PROFILE - Expansion joint has to be calculated according to actual thermal movement 36 riverclack 37

21 PIPE PENETRATION DETAIL S a PIPE PIPE COLLAR 550 mm - Dimension "a" has to be calculated according to actual thermal movement 38 riverclack 39

22 RIDGE SKYLIGHT DETAIL S_AA A RIDGE LINE B B A CLOSURE FLASHING FILLER BLOCK RA140 RIGID INSULATION RIDGE CLOSURE RA170 RIDGE BRACKET RA150 FIXED POINT min. 160 / max. 200 mm RIDGE BLOCK SECTION A-A - Slope > 6% - If slope < 6% please use relevant detail - Mono ridge type considered on this sheet is one of the available options. Please consider proper type according to actual slope. 40 riverclack 41

23 RIDGE SKYLIGHT DETAIL S_BB A RIDGE LINE B B A EAVE BLOCK FLASHING SUPPORT VERGE FLASHING RIGID INSULATION SECTION B-B - Verge type is just one of the possible options. Please see in chapter 03 for alternatives. 42 riverclack 43

24 WELDED ROOFLIGHT DETAIL S_AA B A CLOSURE FLASHING CLOSURE PROFILE B WELDING FLASHING RIGID INSULATION SECTION A-A 44 riverclack 45

25 WELDED ROOFLIGHT DETAIL S_BB B A A SKYLIGHT CLOSURE FLASHING CLOSURE PROFILE B WELDING FLASHING RIGID INSULATION SECTION B-B 46 riverclack 47

26 OVERLAP DETAIL DETAIL S STIFFENING PROFILE RA181 RIDGE BRACKET RA150 FILLER BLOCK RA140 max 200 mm min.160/max.200 mm FIXED POINT BLOCK RA110 RIDGE FLASHING - Walkability is not allowed on overlapping areas - Mono ridge considered on this sheet is one of the available options. Please consider proper type according actual slope. 48 riverclack 49

27 OVERLAP DETAIL DETAIL S EAVE BLOCK JOINT FLASHING STIFFENING PROFILE RA181 RIDGE BRACKET RA157 FILLER BLOCK RA140 RIDGE CLOSURE RA riverclack 51

28 CURVED ROOF RIDGE DETAIL S RIDGE BLOCK FIXED POINT BRACKET RA120 - Slope > 6% - RA120 item to be used according to technical datasheet 52 riverclack 53

29 54 riverclack 55

30

31 EN_2 ISCOM SPA Via Belvedere, Pescantina Italy T F