A: Proposed Scope of Services. B: Site Location Map. C: Selected existing conditions photographs.

Transcription

1 1880 Waycross Road Cincinnati, OH USA Fax E Locust St. Attachments: A: Proposed Scope of Services. B: Site Location Map. C: Selected existing conditions photographs. Jacobs Engineering Group Inc.

2 Attachment A: Scope of Services Project Name: Reed & Peelle, LLC Project Address: 55 E. Locust Street Owner s Request: Energize Clinton County Inc. owns the property at 55 E. Locust Street. They desire to replace the existing windows in the building. The building has been extensively altered to the detriment of its historic condition. Functionally, however, the building seems to be in good condition except for the condition of the windows and a non-historic rear door. Restoration Criteria: The criteria utilized in evaluating this project are derived from the standards developed by the Secretary of the Interior s Standards for Rehabilitation. Scope of Work: Repair or restore existing windows. Provide new interior storm windows. Replace rear door with appropriate door that complements the building but does not attempt to replicate historic materials or design. Specifications: References: Restoration work as required by this project shall be done in accordance with those procedures as described in the appropriate Preservation Briefs as published by the U.S. Department of the Interior, Heritage Preservation Services. Jacobs Engineering Group Inc. 2

3 Windows SECTION INCLUDES: A. Wood ultimate double hung, single hung, transom, 1 5/8 picture, 2 picture window complete with hardware, glazing, weather strip, insect screen, removable grille, simulated divided lite, grilles between the glass, Authentic Divided Lite, jamb extension, combination storm/screen, and standard or specified anchors, trim, and attachments. B. Wood double hung, single hung, bay, bow window complete with hardware, glazing, weather strip, insect screen, removable grille, simulated divided lite, grilles between the glass, jamb extension, combination storm/screen, head/seat board, and standard or specified anchors, trim, and attachments. SYSTEM DESCRIPTION: A. Design and Performance Requirements: 1. Door units shall be designed to comply with ANSI / AAMA / NWWDA 101 / I.S.2 97 and 101 / I.S. 2/ NAFS 02: a. Double Hung / Single Hung: (H LC40 rating up to CN 3036, CN 4026) (H LC30 rating up to CN 4036) b. Transom: (TR-LC40 rating up to CN 6820) c. 1 5/8 Picture: (F-LC40 rating up to CN 6054) d. 2 Picture: (F-LC40 rating up to CN 6878) 2. Air leakage shall not exceed the following when tested at 1.57 psf according to ASTM E 283:.30 cfm per square foot of frame. 3. No water penetration shall occur when units are tested at the following pressure according to ASTM E 547: (H LC40 6.0) (H LC30 4.5) (TR LC40 6.0) (F LC40 6.0) psf. 4. Assembly shall withstand the following positive or negative uniform static air pressure difference without damage when tested according to ASTM E 330: (H LC40 60) (H LC30 45) (TR LC40 60) (F LC40 60) psf. 1.1 DELIVERY A. Deliver in original packaging and protect from weather. 1.2 STORAGE AND HANDLING A. Prime or seal wood surfaces, including surface to be concealed by wall construction, if more than thirty (30) days will expire between delivery and installation. B. Store window units in an upright position in a clean and dry storage area above ground and protect from weather. 1.3 WARRANTY A. Windows shall be warranted to be free from defects in manufacturing, materials, and workmanship for a period of ten (10) years from purchase date. B. Insulating glass shall be warranted against visible obstruction through the glass caused by a failure of the insulating glass air seal for a period of twenty (20) years from the date of original purchase. PART 2 PRODUCTS Jacobs Engineering Group Inc. 3

4 2.1 MANUFACTURED UNITS A. Description: Wood Ultimate Double Hung, Single Hung, Transom, Picture, as manufactured by Marvin Windows and Doors, Warroad, Minnesota or equal. 2.2 FRAME DESCRIPTION A. Finger jointed edge-glued pine, finger jointed, edge-glued Douglas fir, mahogany, vertical grain Douglas fir head and side jambs with interior clear veneer, finger jointed (clear) sill. 1. Kiln dried to moisture content no greater than twelve (12) percent at the time of fabrication. 2. Water repellent preservative treated in accordance with WDMA I.S.4. B. Frame thickness: 11/16 inch (17 mm) head and side jambs, 1-7/16 inches (37 mm) at sill. C. Frame width: 4-9/16 inches (116 mm). 2.3 SASH DESCRIPTION A. Clear pine; Douglas fir, mahogany; vertical grain Douglas fir. 1. Kiln dried to moisture content no greater than twelve (12) percent at the time of fabrication. 2. Water repellent preservative treated in accordance with WDMA I.S.4. B. Sash thickness: 1-5/8 inches (41 mm) for double hung, 1-5/8 inches (41 mm) or 2 inches (51 mm) for picture units. C. Removable exterior glazing stops. 2.4 GLAZING A. Select quality complying with ASTM C Insulating glass SIGMA / IGCC certified to performance level CBA when tested in accordance with ASTM E 774. B. Glazing method: Single glazed; Single glazed with energy panel; insulated glass (Altitude adjusted). C. Glass Type: Clear; Low E II; Argon gas; Tempered; Obscure; Laminated. D. Glazing Seal: Silicone bedding. 2.5 FINISH A. Interior / Exterior: Treated bare wood; Latex prime coat, white available for pine wood species only. 2.6 HARDWARE A. Balance system: Coil spring block and tackle with nylon cord and fiber filled nylon clutch. B. Jamb carrier: Vinyl extrusion with wood inserts. Color: Beige. C. Lock: High pressure zinc die-cast cam lock and keeper. 1. Finish: Phosphate coated and electrostatic ally painted Satin Taupe; Bronze; White; Brass; Satin Chrome; Satin Nickel; Antique Brass; Oil Rubbed Bronze. 2.7 WEATHER STRIP B. Continuous leaf weather strip at head jamb parting stop; dual durometer bulb weather strip at check rail; foam bulb type dual durometer weather strip on vertical sash edge; dual durometer bulb weather strip at bottom rail. Color: Beige. Jacobs Engineering Group Inc. 4

5 2.8 JAMB EXTENSION Factory installed jamb extension for wall thickness indicated or required. Finish: Match interior frame finish. 2.9 INSECT SCREENS A. Factory installed half screen, full screen. Half screen covers bottom sash opening. B. Screen mesh, 18 by 16: Charcoal fiberglass; Charcoal aluminum wire; Black aluminum wire; Bright aluminum wire; Bright bronze wire, HI-Tran fiberglass mesh. C. Aluminum Frame Finish: Bronze; Stone White; Pebble Gray; Brown; Evergreen WOOD COMBINATION STORM SASH AND SCREEN A. Frame: Finger jointed (clear) pine, mahogany, vertical grain Douglas fir. 1. Kiln dried to a moisture content no greater than twelve (12) percent at the time of fabrication. 2. Water repellant preservative treated in accordance with WDMA I.S Frame thickness: 1-1/16 inches (26 mm). 4. Extruded aluminum track utilized to hold storm and screen panels. 5. Finish: Treated bare wood; Latex prime coat, white available for pine wood species only. B. Hardware: Spring loaded latches to hold removable storm panel in position. C. Weather strip: Pile weather strip seals between operating panels and against stiles of main frame. D. Storm Panel: Select quality glass in aluminum frame. 1. Frame finish: Bronze; Bahama Brown; Pebble Gray; White; Evergreen. E. Insect Screen Panel: Extruded aluminum surround, screen mesh, 18 by 16: Charcoal fiberglass; Charcoal aluminum wire; Black aluminum wire; Bright aluminum wire; Bright bronze wire, HI-Tran fiberglass screen mesh. 1. Aluminum frame finish: Bronze; White; Bahama Brown; Pebble Gray; Evergreen. F. Wood Storm Sash: Select quality glass in clear pine, mahogany, vertical grain Douglas fir frame. 1. Top Rail and stiles: 2-1/8 inches (54 mm) wide. 2. Bottom rail: 4-1/16 inches (103 mm) wide. 3. Sash thickness: 1-3/32 inches (28 mm). 4. Finish: Latex prime coat, white available for pine wood species only SIMULATED DIVIDED LITES (SDL) A. 7/8 inch (22 mm) wide; 1-1/8 inch (29 mm) wide. Pine, Douglas fir, mahogany, vertical grain Douglas fir adhered to glass with closed-cell acrylic foam tape. 1. Pattern: Rectangular; Custom lite layout. 2. Finish: Match sash finish ACCESSORIES AND TRIM A. Installations and Hardware Accessories: 1. Aluminum drip cap. Finish: Bahama Brown; Bronze; Evergreen; Pebble Gray; White. 2. Installation brackets: 6-3/8 inches (162 mm); 9-3/8 inches (238 mm); 15-3/8 inches (390 mm). Jacobs Engineering Group Inc. 5

6 3. Masonry brackets: 6 inches (152 mm); 10 inches (254 mm). 4. Marvin SillGuard. 5. Sash lifts: High pressure zinc die-cast. Color: Bronze; White; Brass. B. Exterior Wood Moulding: 1. Profile: Brick mould casing; Flat casing; Stucco Bick Mould Casing; Stucco Fat Casing; no casing / sill horns; as indicated on drawings. 2. Finish: Match exterior frame finish. PART 3 EXECUTION 3.1 EXAMINATION A. Verification of Conditions: Before Installation, verify openings are plumb, square, and of proper dimension. B. Acceptance of Conditions: Beginning of installation confirms acceptance of existing conditions. 3.2 INSTALLATION A. Assemble and install window unit according to manufacturer s instructions and reviewed shop drawings. B. Install sealant and related backing materials at perimeter of unit or assembly. Do not use expansive foam sealant. C. Install accessory items as required. D. Use finish nails to apply wood trim and mouldings. 3.3 CLEANING A. Remove visible labels and adhesive residue according to manufacture s instructions. B. Leave windows and glass in a clean condition. Jacobs Engineering Group Inc. 6

7 Attachment B: Location Map Jacobs Engineering Group Inc. 7

8 Attachment C: Selected Photographs Front façade, looking northeast Jacobs Engineering Group Inc. 8

9 1880 Waycross Road Cincinnati, OH USA Fax Front facade Jacobs Engineering Group Inc.

10 1880 Waycross Road Cincinnati, OH USA Fax Rear ffacade Jacobs Engineering Group Inc.

11 Rear ell with garage door Jacobs Engineering Group Inc. 11