Thermo 74 Windows, French doors, and Terrace doors with low U-values

Transcription

1 Thermo 74 Windows, French doors, and Terrace doors with low U-values Thermo 74 sections are insulated with 30 mm glass fibre reinforced polyamide strips. By inserting additional insulation in the form of an insulating bar of cellular plastic between the thermal break, the insulation will improve the U-value by 0.3 W/m 2 K over the section. Places with high humidity, such as kitchens, bathrooms and swimming pools are best suited for a low U-value system. The location of the window in a wall is very important for high surface temperatures of the sections. The window should always be placed in the warmest part of a wall in order to eliminate thermal bridges. The temperature distribution over window sections is calculated theoretically with the use of FRAME4 software. -15 C +20 C I-9

2 Thermo 74 Windows, French doors, Terrace doors, inward opening SFB 1074 Our new architectural system Thermo 74 is innovative in its design. We have made a great effort to obtain an energy effective system. The future requirements regarding the economical use of energy and environment protection are going to dominate in the construction sector. With Thermo 74 system we get a low U- value and high air tightness in all products. The first striking feature of Thermo 74 is the symmetric design of the system. A thermal break made of glass fibre reinforced polyamide is placed in the middle and it is surrounded on both sides by sections with symmetric chambers and grooves. Thermo 74 has a low U-value of the section including the glass. Double or triple glazing units, as well as 54 mm infil panels which correspond to a U-value of 0.8 W/m 2 K, can be installed in the rebate. Windows, French doors and terrace doors SFB 1074 fulfil the requirements up to highest class as regards air and water tightness, as well as wind load resistances according to National building regulations. Windows can be anodised or powder coated with various colours and type of surface finish on the inside and on the outside. Surface finish: see chapter J. I-10

3 Thermo 74 Windows, French doors, inward opening Frame and sash combinations SFB 1074 Different combinations of frame and sash sections are possible in inward opening SFB 1074 windows. Sash sections for inward opening French doors are available in two versions - one for side-hung fittings (Fix) and one for tilt-and-turn fittings. Functions of fittings: see page I-15. SFB 1074 is used for single windows, windows with top light, windows with side light, or in window elements/ glazed elements. The size of windows: max. height 2100 mm, max. width 1550 mm, min. height 500 mm, min. width 450 mm, and max. weight of sash 100 kg. Fixed window Inward opening window Inward opening window with arched top light ing window with fixed middle post, or without post Inward opening French door Frame/sash combinations in inward opening windows Narrow frame/sash Block window: see page I-16 Narrow frame/concave sash Narrow frame/bevelled sash Frame/sash combinations in inward opening French doors Inward opening French door with glass Inward opening French door with infil panel Meeting door without middle post I-11

4 Thermo 74 Windows, French doors, outward opening Removal of smoke and evacuation of persons SFB 1074 Outward opening windows SFB 1074 have been designed to ensure removal of smoke and appropriate evacuation of persons in the case of fire. Outward opening French doors SFB 1074 with a maximum width of 1200 mm and a height of 2400 mm can be combined with top and side elements. Locking of the French door is ensured by a 3-point casement bolt and a restrictor. The handle can be equipped with a cylinder lock. The outward opening window is based on the same principles as the other windows in our well insulated window system Thermo 74, in which we get a low U-value and high air tightness in all products. A thermal break made of glass fibre reinforced polyamide is placed between symmetric chambers and grooves. Windows and French doors fulfil the requirements up to highest class as regards air and water tightness, as well as wind load resistances according to National building regulations. Window sashes are available in two dimensions. ing and fixed units can be combined into window elements. Double or triple glazing units, as well as 54 mm infil panels which correspond to a U-value of 0.8 W/m 2 K, can be installed in the rebate. Windows and French doors can be anodised or powder coated with various colours and type of surface finish on the inside and on the outside. Surface finish: see chapter J. I-12

5 Thermo 74 Windows, French doors, outward opening Frame and sash combinations Different combinations of frame and sash sections are possible in outward opening SFB 1074 windows. For functions of fittings: see page I-15. Outward opening windows SFB 1074 are used for single windows, windows with top light, and/or side light. The sash sections can be also installed in facade systems SFB 4150, 4060 and 5050, see chapter D, and chapter C for SFB The size of windows: max. height 2400 mm, max. width 1200 mm, min. height 1800 mm, min. width 700 mm, and max. weight of sash 130 kg. Outward opening windows, with arched top light as an alternative Outward opening windows with fixed side lights, or top light as an alternative Frame/sash combinations in outward opening windows Outward opening French door Outward opening French door with top light, or side light as an alternative Frame with narrow sash Frame with wide sash Narrow sash in fixed top/side light Frame/sash combinations in outward opening French doors Wide sash in fixed top/side light Outward opening French door Outward opening French door with infil panel I-13

6 Thermo74 Terrace doors SFB 1074 Terrace doors SFB 1074 with the correct glazing can be used as opening parts in a facade. Terrace doors SFB 1074 are made of the widest sash sections available in the window system. With sliding door fittings, hidden in the grooves of the section system, a terrace door with numerous functions is obtained. In closed position the fixed glass panels are in the same plane as the opening ones. Terrace doors can be tilt-opened inward for ventilation and opened completely to the side with the door sliding on rails on the inside in parallel to the fixed part. In closed position terrace doors SFB 1074 have the same good air and water tightness as windows SFB The handle has a lock as standard. The rebate in terrace doors provides space for double or triple glazing units. Infil panels can be up to 54 mm thick, which corresponds to a U-value of 0.8 W/m 2 K. Terrace doors can be anodised or powder coated with various colours and type of surface finish on the inside and on the outside. Surface finish: see chapter J. Functions of fittings in terrace doors Ventilation Ventilation, bottom-hung Terrace door in closed position - the glass panels are in the same plane Ventilation Sizes of terrace doors Max. height 2400 mm Max. width 1650 mm Max. height + width 3700 mm Max. weight of door leaf 150 kg Terrace doors can be opened completely to the side with the door sliding on rails on the inside in parallel to the fixed part. Fittings in terrace doors SFB 1074 Window system SFB 1074 Closing fittings Siegenia PSK-Portal LM Handle Siegenia PSK LM with lock Glass Glazing unit/special glass Surface finish Anodising/Powder coating I-14

7 Windows, French doors SFB 1050, 1074 Functions of fittings Ventilation Bottom- and side-hung (Tilt-and-turn) SFB 1074 Bottom- and side-hung, inward opening Window system SFB 1074 Closing fitting Siegenia LM 4200-TBT Handle LM Handle with lock LM Ventilation Bottom-hung Side-hung Side-hung SFB 1074 side-hung, inward opening Window system SFB 1074 Closing fitting Siegenia LM 4200-D Handle LM Handle with lock LM Top-hung SFB 1074 Top-hung, inward opening Window system SFB 1074 Closing fitting Siegenia LM-K Terrace doors SFB 1074 in combination with good glazing units provide good possibilities to be used as opening parts in a facade. Bottom-hung SFB 1074 Bottom-hung, inward opening Window system SFB 1074 Closing fitting Siegenia LM-K Handle LM Handle with lock LM Ventilation Bottom- and side-hung (Tilt-and-turn) SFB 1074 Bottom- and side-hung, inward opening Window system SFB 1074 Closing fitting Siegenia LM 4200-TBT Handle LM Handle with lock LM Ventilation Bottom-hung Side-hung SFB 1074 Side-hung, inward opening Window system SFB 1074 Closing fitting Siegenia LM 4200-D Handle LM Handle with lock LM I-15

8 Block windows SFB 1074 Inward opening block windows SFB 1074 have been developed to satisfy the market s requirement of a window with a sash that is not visible from the outside. The block window is based on the same principles as our well insulated window system Thermo 74. A thermal break made of glass fibre reinforced polyamide is placed between symmetric chambers and grooves in frame sections. In order to obtain a hidden sash, the outside glass panel of the glazing unit is stepped and joined with the sash section. Euro-grooves in the frame and sash sections are adapted for inward opening fittings, which can provide side, bottom and top hung functions. ing and fixed units can be combined with identical sight lines. The windows fulfil the requirements up to highest class as regards air and water tightness, as well as wind load resistances according to National building regulations. Block windows can be anodised or powder coated with various colours and type of surface finish on the inside and on the outside. Surface finish: see chapter J. I-16

9 Block windows SFB 1074 Frame and sash combinations Different combinations of frame and sash sections are possible in block windows SFB For functions of fittings: see page I-15. The sash sections can be also installed in facade systems SFB 4150, 4060 and 5050, see chapter D, and chapter C for SFB The sash of block windows is used for single windows or windows with top or side light combinations. The size of windows: max. height 2100 mm, max. width 1500 mm, min. height 500 mm, min. width 450 mm, and max. weight of sash 100 kg. Inward opening windows Inward opening windows with arched top light ing window with fixed middle post ing/fixed window Frame/sash combinations in windows Narrow frame/sash Wide frame/sash Block window in facade SFB 4050 (SFB 4060, 5050) ing/fixed window ing window with fixed middle post I-17

10 Outward opening gliding window SFB 1105 The window system SFB 1105 is an outward opening, entirely reversible aluminium window. It has many exclusive features, functions and combinations, such as hidden fittings, drainage, drip plate connection, child safety device and 180 reversibility with dual colours on the inside and on the outside. The section depth is 105 mm and the thermal break is made of glass fibre reinforced polyamide. The horizontal or vertical gliding fitting is hidden between the frame and the sash. It has an integrated child safety device and two ventilation positions. The window can be reversed by 180 so that the outside can be cleaned from the inside. The rebate of the window provides space for double or triple glazing units. The windows can be anodised or powder coated with various colours and type of surface finish on the inside and on the outside. Surface finish: see chapter J. I-18

11 Windows SFB 1105 Frame and sash combinations SFB 1105 can be made as fixed windows, outward opening horizontally hung window, outward opening vertically hung window, and outward opening side, bottom, or top-hung window. Apart from this, horizontal and vertical middle posts are available for different combinations with fixed and opening windows. Size of opening windows Outward opening horizontally hung gliding window SFB 1105 GH, max. height 1600 mm, max. weight of sash 70 kg. Outward opening vertically hung gliding window SFB 1105 GV, max. height 1600 mm, max. weight of sash 50 kg. Outward opening side-hung window SFB 1105 S, max. weight of sash 45 kg. Functions of windows Fixed window Outward opening Double window, opening/fixed SFB 1105 GH window Outward opening gliding window SFB 1105 GV Outward opening gliding window SFB 1105 S Outward opening sidehung window Frame/sash combinations Frame with double glazing unit Frame with triple glazing unit Sash with double glazing unit Sash with triple glazing unit Vertical middle post with double glazing unit Vertical middle post with double glazing unit, fixed and opening window Vertical middle post, opening windows I-19

12 Windows SFB 1105 Functions of fittings SFB 1105 GH, outward opening horizontally hung window with hidden fittings which reverse the window by 180 on the outside of the frame. The fitting has the following functions: closed, ventilation position and cleaning position, in which the outside of the window can be cleaned from the inside. The fitting has an integrated child safety device. SFB 1105 GV, outward opening vertically hung window with hidden fittings which reverse the window by 180 on the outside of the frame. The fitting has the following functions: closed, ventilation position and cleaning position, in which the outside of the window can be cleaned from the inside. The window can be complemented with a child safety device. SFB 1105 S, outward opening sidehung window with hidden hinges. The window can be also made as top- or bottom-hung, and complemented with a child safety device. Standard handle Handle with lock Child safety device integrated in the horizontally hung fitting Child safety device in vertically hung windows I-20

13 Windows SFB 1105 Surface-mounted cross bars SFB 1105 window system can be equipped with detachable cross bars made of aluminium sections. The cross bars, which are 28 mm wide and 13 mm deep, are installed approx. 6 mm from the outside glass panel of the window. The installation of the cross bars is easy with snap-in locks can also be removed for cleaning. The choice of position is entirely free. The cross bars can be anodised or powder coated with various colours. Surface finish: see chapter J. SFB 1105 with surface-mounted cross bars SFB 1105, easily detachable cross bars with snap-in locks Surface-mounted cross bar SFB 1105 I-21

14 Windows, uninsulated SFB 1050 Uninsulated inward opening window SFB 1050 has been developed for applications where opening windows are required without the need of low U-values. Euro-grooves in the frame and sash sections are adapted for inward opening fittings, which can provide side, top and bottom-hung functions. ing and fixed units can be combined into window elements. The rebate in the window sash is adapted for single glass, double glazing units or 33 mm insulated filling panels. The windows fulfil the requirements up to highest class as regards air and water tightness, as well as wind load resistances according to National building regulations. The windows can be anodised or powder coated with various colours and type of surface finish on the inside and on the outside. Surface finish: see chapter J. I-22

15 Windows SFB 1050 Frame and sash combinations Different functions can be obtained in inward opening uninsulated windows SFB For functions of fittings: see page I-15. The sash sections can be also installed in facade systems SFB 4150, 4060 and 5050, see chapter D, and chapter C for SFB SFB 1050 is used for single windows, windows with top light, windows with side light, or in window glazed elements. The size of windows: max. height 2100 mm, max. width 1550 mm, min. height 500 mm, min. width 450 mm, and max. weight of sash 100 kg. Fixed window Inward opening window Inward opening window with arched top light ing window with fixed middle post Inward opening French door Glazing alternatives in fixed and opening windows ing window with single glass ing window with glazing unit Fixed window with single glass Fixed window with glazing unit Filling panels in fixed and opening windows/french doors Inward opening window/ French door with infil panel Fixed window with infil panel I-23