SLIDING SECTION 8 SPECIFICATIONS

Transcription

1 GUIDE SPECIFICATIONS - SECTION LaCantina ALUMINUM Sliding Door System PART 1 GENERAL 1.1 SECTION INCLUDES A. Aluminum multi-slide doors. B. Aluminum slider doors. C. Aluminum Thermally Controlled multi-slide doors. D. Aluminum Thermally Controlled slider doors. E. Aluminum Wood multi-slide doors. F. Aluminum Wood slide doors. 1.2 RELATED SECTIONS A. Section Rough Carpentry. B. Section Finish Carpentry. C. Section Joint Protection. D. Section Hardware. 1.3 REFERENCES A. AAMA Voluntary Specification for Anodized Architectural Aluminum. B. AAMA Voluntary Specifications, Performance Requirements and Test Procedures for Pigmented Organic Coatings on Aluminum Extrusions and Panels. C. AAMA Voluntary Specifications, Performance Requirements and Test Procedures for Pigmented for High Performance Organic Coatings on Aluminum Extrusions and Panels. D. ANSI Z Safety Performance Specifications and Methods of Test for Safety Glazing Material Used In Buildings. E. ASTM E Test Method for Rate of Air Leakage through Exterior Windows, Curtain Walls, and Doors by Uniform Static Air Pressure Difference. F. ASTM E Test Method for Structural Performance of Exterior Windows, Curtain Walls, and Doors by Uniform Static Air Pressure Difference. G. ASTM E Test Method for Water Penetration of Exterior Windows, Curtain Walls, and Doors by Cyclic Static Air Pressure Differential. H. CPSC 16CFR Safety Standard for Architectural Glazing Materials. 1.4 DESIGN / PERFORMANCE REQUIREMENTS A. Sliding Door Systems to comply with the performance requirements specified with independently certified testing results. B. Aluminum Multi Slide Doors: 1. Test Results: Size tested 60 inches by 96 inches with weather resistant sill a. Air Infiltration: ASTM E 283 when tested at 1.6 psf (25 mph), 0.13 CFM/FT2 b. Water Infiltration: ASTM E 547 when tested at 6.0 PSF, DP 40, No Leakage c. Uniform Load Deflection: ASTM E 330 when tested at plus or minus 40.0 PSF, DP 40, 1.15 inch Positive / 0.98 inch Negative

2 d. Uniform Load Structural: ASTM E 330 when tested at plus or minus 60.0 PSF, DP 40, 0.19 inch Positive / 0.09 inch Negative e. Overall Design Pressure Rating: DP 40 C. Aluminum Slider Doors: 1. Test Results: Size tested 60 inches by 96 inches with weather resistant sill a. Air Infiltration: ASTM E 283 when tested at 1.6 psf (25 mph), 0.13 CFM/FT2 b. Water Infiltration: ASTM E 547 when tested at 6.0 PSF, DP 40, No Leakage c. Uniform Load Deflection: ASTM E 330 when tested at plus or minus 40.0 PSF, DP 40, 1.15 inch Positive / 0.98 inch Negative d. Uniform Load Structural: ASTM E 330 when tested at plus or minus 60.0 PSF, DP 40, 0.19 inch Positive / 0.09 inch Negative e. Overall Design Pressure Rating: DP 40 D. Aluminum Thermally Controlled Multi Slide Doors: 1. Test Results: Size tested 60 inches by 96 inches with weather resistant sill a. Air Infiltration: ASTM E 283 when tested at 1.6 psf (25 mph), 0.15 CFM/FT2 b. Water Infiltration: ASTM E 547 when tested at 6.0 PSF, DP 40, No Leakage c. Uniform Load Deflection: ASTM E 330 when tested at plus or minus 40.0 PSF, DP 40, 0.98 inch Positive / 0.98 inch Negative d. Uniform Load Structural: ASTM E 330 when tested at plus or minus 60.0 PSF, DP 40, 0.19 inch Positive / 0.09 inch Negative e. Overall Design Pressure Rating: DP 40 E. Aluminum Thermally Controlled Slider Doors: 1. Test Results: Size tested 60 inches by 96 inches with weather resistant sill a. Air Infiltration: ASTM E 283 when tested at 1.6 psf (25 mph), 0.15 CFM/FT2 b. Water Infiltration: ASTM E 547 when tested at 6.0 PSF, DP 40, No Leakage c. Uniform Load Deflection: ASTM E 330 when tested at plus or minus 40.0 PSF, DP 40, 0.98 inch Positive / 0.98 inch Negative d. Uniform Load Structural: ASTM E 330 when tested at plus or minus 60.0 PSF, DP 40, 0.19 inch Positive / 0.09 inch Negative e. Overall Design Pressure Rating: DP 40 F. Aluminum Wood Multi Slide Doors: 1. Test Results: Size tested 60 inches by 96 inches with weather resistant sill a. Air Infiltration: ASTM E 283 when tested at 1.6 psf (25 mph), 0.18 CFM/FT2 b. Water Infiltration: ASTM E 547 when tested at 6.0 PSF, DP 40, No Leakage c. Uniform Load Deflection: ASTM E 330 when tested at plus or minus 40.0 PSF, DP 40, 0.98 inch Positive / 0.90 inch Negative d. Uniform Load Structural: ASTM E 330 when tested at plus or minus 60.0 PSF, DP 40, 0.19 inch Positive / 0.09 inch Negative e. Overall Design Pressure Rating: DP 40 G. Aluminum Wood Slide Doors: 1. Test Results: Size tested 60 inches by 96 inches with weather resistant sill a. Air Infiltration: ASTM E 283 when tested at 1.6 psf (25 mph), 0.18 CFM/FT2 b. Water Infiltration: ASTM E 547 when tested at 6.0 PSF, DP 40, No Leakage c. Uniform Load Deflection: ASTM E 330 when tested at plus or minus 40.0 PSF, DP 40, 0.98 inch Positive / 0.90 inch Negative d. Uniform Load Structural: ASTM E 330 when tested at plus or minus 60.0 PSF, DP 40, 0.19 inch Positive / 0.09 inch Negative e. Overall Design Pressure Rating: DP SUBMITTALS A. Submit under provisions of Section Administrative Requirements

3 B. Product Data: Manufacturer's data sheets on each product to be used, including: 1. Preparation instructions and recommendations. 2. Storage and handling requirements and recommendations. 3. Installation methods. C. Shop Drawings: Include outside net frame dimensioning, direction of swing (outswing or inswing), number of panels, folding configuration of panels left or right, identify main entry swing panel, typical head, side jamb, sill and panel details and type of glazing material per vertical plan and elevations view drawings. D. LEED Submittals: Provide documentation of how the requirements of Credit will be met: 1. List of proposed materials with recycled content. Indicate post-consumer recycled content and pre-consumer recycled content for each product having recycled content. 2. Product data and certification letter indicating percentages by weight of postconsumer and pre-consumer recycled content for products having recycled content. E. Selection Samples: For each finish product specified, two complete sets of color chips representing manufacturer's full range of available colors and patterns. F. Verification Samples: For each finish product specified, two samples, minimum size 6 inches (150 mm) square, representing actual product, color, and patterns. G. Manufacturer's Certificates: Certify products meet or exceed specified requirements. H. Closeout Submittals: Provide manufacturer's maintenance instructions that include recommendations for periodic checking and adjustment of cable tension and periodic cleaning and maintenance of all railing and infill components. 1.6 QUALITY ASSURANCE A. Manufacturer Qualifications: Provide complete, engineered and high quality sliding door system by a single source manufacturer with at least 7 years documented experience manufacturing folding door systems in the U.S. B. Installer Qualifications: Installer with documented experienced in the installation of manufacturer's sliding door systems or similar and screen system to the products specified. C. Mock-Up: Provide a mock-up for evaluation of surface preparation techniques and application workmanship. 1. Finish areas designated by Architect. 2. Do not proceed with remaining work until workmanship, color, and sheen are approved by Architect. 3. Refinish mock-up area as required to produce acceptable work. 1.7 DELIVERY, STORAGE, AND HANDLING A. Store products in manufacturer's unopened packaging until ready for installation. B. Protect stored product from damage. Store products flat in dry, well ventilated area out of direct sunlight, under cover, protected from weather, moisture and excessive dryness and construction activities. 1.8 SEQUENCING A. Ensure that locating templates and other information required for installation of products of this section are furnished to affected trades in time to prevent interruption of construction progress

4 B. Ensure that products of this section are supplied to affected trades in time to prevent interruption of construction progress. 1.9 PROJECT CONDITIONS A. Maintain environmental conditions (temperature, humidity, and ventilation) within limits recommended by manufacturer for optimum results. Do not install products under environmental conditions outside manufacturer's absolute limits WARRANTY A. Manufacture's limited warranty including; 10 years for panel and frame aluminum components, product finishes, folding system hardware, and weather stripping; 5 years for locking hardware and screens; 10 years for insulated glass against failure of the air seal and that each unit will be free from material obstruction of vision as a result of fogging or film formation on the internal surfaces. PART 2 PRODUCTS 2.1 MANUFACTURERS A. Acceptable Manufacturer: LaCantina Doors, which is located at: 1875 Ord Way; Oceanside, CA 92056; Toll Free Tel: ; Tel: ; Fax: ; request info (sales@lacantinadoors.com); Web: B. Substitutions: Not permitted. C. Requests for substitutions will be considered in accordance with provisions of Section Product Requirements. 2.2 SLIDING ALUMINUM DOORS A. Aluminum Multi Slide Doors: 1. Configuration: Complete sliding door system including head, side jambs, thresholds and aluminum sliding panels to sizes indicated on the Drawings. a. Complete sliding door system including head, side jambs, thresholds and aluminum sliding panels to sizes indicated on the Drawings. b. Non-Pocket Configurations: Complete sliding door system including head, side jambs, thresholds and aluminum sliding panels to the following sizes. 1) 3 Panels OXX or XXO Maximum Frame Width 23 feet 9-3/4 inches by Maximum Frame Height 12 foot 3-1/16 inches. 2) 4 Panels OXXX or XXXO or OX XO Maximum Frame Width 31 feet 6-3/4 inches by Maximum Frame Height 12 foot 3-1/16 inches. 3) 5 Panels OXXXX or XXXXO Maximum Frame Width 39 feet 3-3/4 inches by Maximum Frame Height 12 foot 3-1/16 inches 4) 6 Panels OXXXXXX or XXXXXXO or OXX XXO Maximum Frame Width 47 feet 1-1/16 inches by Maximum Frame Height 12 foot 3-1/16 inches. c. Pocket Configurations: Complete sliding door system including head, side jambs, thresholds and aluminum sliding panels to the following sizes. 1) 1 Panel PX or XP Maximum Frame Width 16 feet 4 inches by Maximum Frame Height 12 feet 3-1/16 inches. 2) 2 Panels PXX or XXP or PX XP Maximum Frame Width 24 feet 5/16 inches by Maximum Frame Height 12 feet 3-1/16 inches. 3) 3 Panels PXXX or XXXP Maximum Frame Width 31 feet 8-5/8 inches by Maximum Frame Height 12 foot 3-1/16 inches. 4) 4 Panels PXXXX or XXXXP or PXX XXP Maximum Frame Width 39 feet 4-15/16 inches by Maximum Frame Height 12 foot 3-1/16 inches

5 5) 5 Panels PXXXXX or XXXXXP Maximum Frame Width 47 feet 1-1/4 inches by Maximum Frame Height 12 foot 3-1/16 inches. 6) 6 Panels PXXXXXX or XXXXXXP or PXXX XXXP Maximum Frame Width 54 feet 9-9/16 inches by Maximum Frame Height 12 feet 3-1/16 inches. 2. Frame and Panels: Complete folding door system including head, side jambs, thresholds and aluminum panels to sizes indicated on the Drawings. a. Panel: Extruded aluminum stile and rail panels with standard one lite. 1) Stile and Rail 2-3/4 inches (70 mm). b. Frame and Sill: Extruded aluminum. 1) Frame width: inches ( mm). c. Weatherstripping: Weather seal inserted in frame and sill to provide perimeter seal, as well as between door panels. Color is dark bronze. 3. Glass: All glass to comply with safety glazing requirements of ANSI Z97.1 and CPSC 16CFR a. Type: Cardinal dual glazed low-e glass. 1) Insulated glass with a 3/4 inch (19 mm) overall thickness. b. Glass: 1) Air Filled: a) Clear-Air-Clear: Overall Thickness 3/4 inch, U-Factor 0.66, SHGC 0.59, VT 0.62 b) LowE180-Air-Clear: Overall Thickness 3/4 inch, U-Factor 0.54, c) LowE272-Air-Clear: Overall Thickness 3/4 inch, U-Factor 0.53, d) LowE366-Air-Clear: Overall Thickness 3/4 inch, U-Factor 0.52, SHGC 0.23, VT ) Argon Filled: a) Clear-Argon-Clear: Overall Thickness 3/4 inch, U-Factor 0.63, SHGC 0.59, VT 0.62 b) LowE180-Argon-Clear: Overall Thickness 3/4 inch, U-Factor 0.50, c) LowE272-Argon-Clear: Overall Thickness 3/4 inch, U-Factor 0.49, d) LowE366-Argon-Clear: Overall Thickness 3/4 inch, U-Factor 0.48, SHGC 0.22, VT 0.49 e) Solarban SB60-Argon-Clear: Overall Thickness 3/4 inch, U-Factor 0.49, SHGC 0.32, VT ) Argon Filled with room side LowE I89. a) LowE272-Argon-LowE I89: Overall Thickness 3/4 inch, U-Factor 0.45, SHGC 0.32, VT 0.53 b) LowE240-Argon-LowE I89: Overall Thickness 3/4 inch, U-Factor 0.45, SHGC 0.20, VT 0.29 c) LowE366-Argon-LowE I89: Overall Thickness 3/4 inch, U-Factor 0.45, SHGC 0.22, VT 0.48 c. Glazing: Silicone bedding on exterior surfaces and glazing seal on the interior of the panel. d. Simulated Divided Lites: Sculpted profile as selected. 4. Locking Hardware and Handles: Manufacturer's standard minimal one piece handle and exterior locking hardware. a. Provide with standard two point lock system secures large sliding panels with locking hardware located on the primary sliding panel. b. Provide with optional three point lock system available for systems 8 feet or taller with locking hardware located on the primary sliding panel. c. Handle Finish: 1) Brushed Satin Aluminum color

6 2) Brushed Satin Bronze color. d. Provide panel handle height centered at 36 inches (914 mm) from bottom of panel. 5. Rolling Hardware: Manufacturer's standard rolling hardware integrated with engineered head track, side jambs and threshold frame system. a. Rolling Hardware: 1) Nylon polyamide plastic wheels. 2) Stainless steel wheels. b. Threshold: 1) Standard Self-draining Weather Resistant Sill with interior stop height options for all weather conditions. 2) Flush sill. 3) Ramp sill. 4) ADA Compliant ramp sill. 6. Aluminum Finish: Provide same finishes on inside and outside. a. Clear anodized c. White paint. d. Two coat 70 percent Kynar finish with color as selected from manufacturer range of finishes. e. Two coat 70 percent Kynar finish with custom color. f. Decoral wood grain finish with color as selected. 7. Threshold Finish: a. Clear anodized. 8. Screen and Blind: Provide horizontal, retractable non-pleated insect and solar control screen and blind system with fingertip operation, load balancing and tensioning adjustment. a. Screen Mechanism: 1) Stand alone type. 2) Concealed within frame and integrated with door system. b. Operation: 1) Single function for blinds up to 12 feet (3.65 m).wide and 10 feet (3.04 m) tall. 2) Double function for blinds up to 24 feet (7.31 m) wide and 10 feet (3.04 m) tall. 3) Multi-function screen and blind system up to 24 feet (7.31 m) wide and 7 feet 6 inches (2.29 m) tall. c. Screen Mesh: Fiberglass/PVC mesh as selected from manufacturer's available selection for: 1) Insect protection. 2) Control heat gain or loss. 3) UV protection. 4) Projector screen. d. Finish: 1) Anodized finish in manufacturer's standard color 2) Anodized finish in custom color. 3) Wood veneer from manufacturer's standard selections. B. Aluminum Slider Doors: 1. Configuration: Complete sliding door system including head, side jambs, thresholds and aluminum sliding panels to sizes indicated on the Drawings. a. Complete sliding door system including head, side jambs, thresholds and aluminum sliding panels to sizes indicated on the Drawings. b. Non-Pocket Configurations: Complete sliding door system including head, side jambs, thresholds and aluminum sliding panels to the following sizes

7 1) 2 Panels OX or XO Maximum Frame Width 16 feet 13/16 inches by Maximum Frame Height 12 foot 3-1/16 inches. 2. Frame and Panels: Complete folding door system including head, side jambs, thresholds and aluminum panels to sizes indicated on the Drawings. a. Panel: Extruded aluminum stile and rail panels with standard one lite. 1) Stile and Rail 2-3/4 inches (70 mm). b. Frame and Sill: Extruded aluminum. 1) Frame width: inches ( mm). c. Weatherstripping: Weather seal inserted in frame and sill to provide perimeter seal, as well as between door panels. Color is dark bronze. 3. Glass: All glass to comply with safety glazing requirements of ANSI Z97.1 and CPSC 16CFR a. Type: Cardinal dual glazed low-e glass. 1) Insulated glass with a 3/4 inch (19 mm) overall thickness. b. Glass: 1) Air Filled: a) Clear-Air-Clear: Overall Thickness 3/4 inch, U-Factor 0.66, SHGC 0.59, VT 0.62 b) LowE180-Air-Clear: Overall Thickness 3/4 inch, U-Factor 0.54, c) LowE272-Air-Clear: Overall Thickness 3/4 inch, U-Factor 0.53, d) LowE366-Air-Clear: Overall Thickness 3/4 inch, U-Factor 0.52, SHGC 0.23, VT ) Argon Filled: a) Clear-Argon-Clear: Overall Thickness 3/4 inch, U-Factor 0.63, SHGC 0.59, VT 0.62 b) LowE180-Argon-Clear: Overall Thickness 3/4 inch, U-Factor 0.50, c) LowE272-Argon-Clear: Overall Thickness 3/4 inch, U-Factor 0.49, d) LowE366-Argon-Clear: Overall Thickness 3/4 inch, U-Factor 0.48, SHGC 0.22, VT 0.49 e) Solarban SB60-Argon-Clear: Overall Thickness 3/4 inch, U-Factor 0.49, SHGC 0.32, VT ) Argon Filled with room side LowE I89. a) LowE272-Argon-LowE I89: Overall Thickness 3/4 inch, U-Factor 0.45, SHGC 0.32, VT 0.53 b) LowE240-Argon-LowE I89: Overall Thickness 3/4 inch, U-Factor 0.45, SHGC 0.20, VT 0.29 c) LowE366-Argon-LowE I89: Overall Thickness 3/4 inch, U-Factor 0.45, SHGC 0.22, VT 0.48 c. Glazing: Silicone bedding on exterior surfaces and glazing seal on the interior of the panel. d. Simulated Divided Lites: Sculpted profile as selected. 4. Locking Hardware and Handles: Manufacturer's standard minimal one piece handle and exterior locking hardware. a. Provide with standard two point lock system secures large sliding panels with locking hardware located on the primary sliding panel. b. Provide with optional three point lock system available for systems 8 feet or taller with locking hardware located on the primary sliding panel. c. Handle Finish: 1) Brushed Satin Aluminum color. 2) Brushed Satin Bronze color. d. Provide panel handle height centered at 36 inches (914 mm) from bottom of panel

8 5. Rolling Hardware: Manufacturer's standard rolling hardware integrated with engineered head track, side jambs and threshold frame system. a. Rolling Hardware: 1) Nylon polyamide plastic wheels. 2) Stainless steel wheels. b. Threshold: 1) Standard Self-draining Weather Resistant Sill with interior stop height options for all weather conditions. 2) Flush sill. 3) Ramp sill. 4) ADA Compliant ramp sill. 6. Aluminum Finish: Provide same finishes on inside and outside. a. Clear anodized c. White paint. d. Two coat 70 percent Kynar finish with color as selected from manufacturer range of finishes. e. Two coat 70 percent Kynar finish with custom color. f. Decoral wood grain finish with color as selected. 7. Threshold Finish: a. Clear anodized. 8. Screen and Blind: Provide horizontal, retractable non-pleated insect and solar control screen and blind system with fingertip operation, load balancing and tensioning adjustment. a. Screen Mechanism: 1) Stand alone type. 2) Concealed within frame and integrated with door system. b. Operation: 1) Single function for blinds up to 12 feet (3.65 m).wide and 10 feet (3.04 m) tall. 2) Double function for blinds up to 24 feet (7.31 m) wide and 10 feet (3.04 m) tall. 3) Multi-function screen and blind system up to 24 feet (7.31 m) wide and 7 feet 6 inches (2.29 m) tall. c. Screen Mesh: Fiberglass/PVC mesh as selected from manufacturer's available selection for: 1) Insect protection. 2) Control heat gain or loss. 3) UV protection. 4) Projector screen. d. Finish: 1) Anodized finish in manufacturer's standard color 2) Anodized finish in custom color. 3) Wood veneer from manufacturer's standard selections. C. Aluminum Thermally Controlled Multi Slide Doors: 1. Configuration: Complete sliding door system including head, side jambs, thresholds and aluminum sliding panels to sizes indicated on the Drawings. a. Complete sliding door system including head, side jambs, thresholds and aluminum sliding panels to sizes indicated on the Drawings. b. Non-Pocket Configurations: Complete sliding door system including head, side jambs, thresholds and aluminum sliding panels to the following sizes. 1) 3 Panels OXX or XXO Maximum Frame Width 23 feet 9-3/4 inches by Maximum Frame Height 12 foot 3-1/16 inches. 2) 4 Panels OXXX or XXXO or OX XO Maximum Frame Width 31 feet 6-3/

9 inches by Maximum Frame Height 12 foot 3-1/16 inches. 3) 5 Panels OXXXX or XXXXO Maximum Frame Width 39 feet 3-3/4 inches by Maximum Frame Height 12 foot 3-1/16 inches 4) 6 Panels OXXXXXX or XXXXXXO or OXX XXO Maximum Frame Width 47 feet 1-1/16 inches by Maximum Frame Height 12 foot 3-1/16 inches. c. Pocket Configurations: Complete sliding door system including head, side jambs, thresholds and aluminum sliding panels to the following sizes. 1) 1 Panel PX or XP Maximum Frame Width 16 feet 4 inches by Maximum Frame Height 12 feet 3-1/16 inches. 2) 2 Panels PXX or XXP or PX XP Maximum Frame Width 24 feet 5/16 inches by Maximum Frame Height 12 feet 3-1/16 inches. 3) 3 Panels PXXX or XXXP Maximum Frame Width 31 feet 8-5/8 inches by Maximum Frame Height 12 foot 3-1/16 inches. 4) 4 Panels PXXXX or XXXXP or PXX XXP Maximum Frame Width 39 feet 4-15/16 inches by Maximum Frame Height 12 foot 3-1/16 inches. 5) 5 Panels PXXXXX or XXXXXP Maximum Frame Width 47 feet 1-1/4 inches by Maximum Frame Height 12 foot 3-1/16 inches. 6) 6 Panels PXXXXXX or XXXXXXP or PXXX XXXP Maximum Frame Width 54 feet 9-9/16 inches by Maximum Frame Height 12 feet 3-1/16 inches. 2. Frame and Panels: Complete folding door system including head, side jambs, thresholds and aluminum panels to sizes indicated on the Drawings. a. Panel: Thermally broken, extruded aluminum stile and rail panels with standard one lite. 1) Stile and Rail 2-3/4 inches (70 mm). b. Frame and Sill: Extruded aluminum. 1) Frame width: inches ( mm). c. Weatherstripping: Weather seal inserted in frame and sill to provide perimeter seal, as well as between door panels. Color is dark bronze. 3. Glass: All glass to comply with safety glazing requirements of ANSI Z97.1 and CPSC 16CFR a. Type: Cardinal dual glazed low-e glass. 1) Insulated glass with a 3/4 inch (19 mm) overall thickness. b. Glass: 1) Air Filled: a) Clear-Air-Clear: Overall Thickness 3/4 inch, U-Factor 0.66, SHGC 0.59, VT 0.62 b) LowE180-Air-Clear: Overall Thickness 3/4 inch, U-Factor 0.54, c) LowE272-Air-Clear: Overall Thickness 3/4 inch, U-Factor 0.53, d) LowE366-Air-Clear: Overall Thickness 3/4 inch, U-Factor 0.52, SHGC 0.23, VT ) Argon Filled: a) Clear-Argon-Clear: Overall Thickness 3/4 inch, U-Factor 0.63, SHGC 0.59, VT 0.62 b) LowE180-Argon-Clear: Overall Thickness 3/4 inch, U-Factor 0.50, c) LowE272-Argon-Clear: Overall Thickness 3/4 inch, U-Factor 0.49, d) LowE366-Argon-Clear: Overall Thickness 3/4 inch, U-Factor 0.48, SHGC 0.22, VT 0.49 e) Solarban SB60-Argon-Clear: Overall Thickness 3/4 inch, U-Factor 0.49, SHGC 0.32, VT ) Argon Filled with room side LowE I89. a) LowE272-Argon-LowE I89: Overall Thickness 3/4 inch, U-Factor

10 0.45, SHGC 0.32, VT 0.53 b) LowE240-Argon-LowE I89: Overall Thickness 3/4 inch, U-Factor 0.45, SHGC 0.20, VT 0.29 c) LowE366-Argon-LowE I89: Overall Thickness 3/4 inch, U-Factor 0.45, SHGC 0.22, VT 0.48 c. Glazing: Silicone bedding on exterior surfaces and glazing seal on the interior of the panel. d. Simulated Divided Lites: Sculpted profile as selected. 4. Locking Hardware and Handles: Manufacturer's standard minimal one piece handle and exterior locking hardware. a. Provide with standard two point lock system secures large sliding panels with locking hardware located on the primary sliding panel. b. Provide with optional three point lock system available for systems 8 feet or taller with locking hardware located on the primary sliding panel. c. Handle Finish: 1) Brushed Satin Aluminum color. 2) Brushed Satin Bronze color. d. Provide panel handle height centered at 36 inches (914 mm) from bottom of panel. 5. Rolling Hardware: Manufacturer's standard rolling hardware integrated with engineered head track, side jambs and threshold frame system. a. Rolling Hardware: 1) Nylon polyamide plastic wheels. 2) Stainless steel wheels. b. Threshold: 1) Standard Self-draining Weather Resistant Sill with interior stop height options for all weather conditions. 2) Flush sill. 3) Ramp sill. 4) ADA Compliant ramp sill. 6. Aluminum Finish: Provide same finishes on inside and outside. a. Clear anodized c. White paint. d. Two coat 70 percent Kynar finish with color as selected from manufacturer range of finishes. e. Two coat 70 percent Kynar finish with custom color. f. Decoral wood grain finish with color as selected. 7. Threshold Finish: a. Clear anodized. 8. Screen and Blind: Provide horizontal, retractable non-pleated insect and solar control screen and blind system with fingertip operation, load balancing and tensioning adjustment. a. Screen Mechanism: 1) Stand alone type. 2) Concealed within frame and integrated with door system. b. Operation: 1) Single function for blinds up to 12 feet (3.65 m).wide and 10 feet (3.04 m) tall. 2) Double function for blinds up to 24 feet (7.31 m) wide and 10 feet (3.04 m) tall. 3) Multi-function screen and blind system up to 24 feet (7.31 m) wide and 7 feet 6 inches (2.29 m) tall. c. Screen Mesh: Fiberglass/PVC mesh as selected from manufacturer's available selection for:

11 1) Insect protection. 2) Control heat gain or loss. 3) UV protection. 4) Projector screen. d. Finish: 1) Anodized finish in manufacturer's standard color 2) Anodized finish in custom color. 3) Wood veneer from manufacturer's standard selections. D. Aluminum Thermally Controlled Slider Doors: 1. Configuration: Complete sliding door system including head, side jambs, thresholds and aluminum sliding panels to sizes indicated on the Drawings. a. Complete sliding door system including head, side jambs, thresholds and aluminum sliding panels to sizes indicated on the Drawings. b. Non-Pocket Configurations: Complete sliding door system including head, side jambs, thresholds and aluminum sliding panels to the following sizes. 1) 2 Panels OX or XO Maximum Frame Width 12 feet 13/16 inches by Maximum Frame Height 12 foot 3-1/16 inches. 2. Frame and Panels: Complete folding door system including head, side jambs, thresholds and aluminum panels to sizes indicated on the Drawings. a. Panel: Thermally broken, extruded aluminum stile and rail panels with standard one lite. 1) Stile and Rail 2-3/4 inches (70 mm). b. Frame and Sill: Extruded aluminum. 1) Frame width: inches ( mm). c. Weatherstripping: Weather seal inserted in frame and sill to provide perimeter seal, as well as between door panels. Color is dark bronze. 3. Glass: All glass to comply with safety glazing requirements of ANSI Z97.1 and CPSC 16CFR a. Type: Cardinal dual glazed low-e glass. 1) Insulated glass with a 3/4 inch (19 mm) overall thickness. b. Glass: 1) Air Filled: a) Clear-Air-Clear: Overall Thickness 3/4 inch, U-Factor 0.60, SHGC 0.57, VT 0.61 b) LowE180-Air-Clear: Overall Thickness 3/4 inch, U-Factor 0.48, SHGC 0.48, VT 0.59 c) LowE272-Air-Clear: Overall Thickness 3/4 inch, U-Factor 0.47, SHGC 0.32, VT 0.53 d) LowE366-Air-Clear: Overall Thickness 3/4 inch, U-Factor 0.46, SHGC 0.22, VT ) Argon Filled: a) Clear-Argon-Clear: Overall Thickness 3/4 inch, U-Factor 0.57, SHGC 0.58, VT 0.61 b) LowE180-Argon-Clear: Overall Thickness 3/4 inch, U-Factor 0.44, SHGC 0.48, VT 0.59 c) LowE272-Argon-Clear: Overall Thickness 3/4 inch, U-Factor 0.43, SHGC 0.32, VT 0.53 d) LowE366-Argon-Clear: Overall Thickness 3/4 inch, U-Factor 0.42, SHGC 0.22, VT 0.48 e) Solarban SB60-Argon-Clear: Overall Thickness 3/4 inch, U-Factor 0.39, SHGC 0.21, VT ) Argon Filled with room side LowE I89. a) LowE272-Argon-LowE I89: Overall Thickness 3/4 inch, U-Factor 0.39, SHGC 0.31, VT 0.52 b) LowE240-Argon-LowE I89: Overall Thickness 3/4 inch, U-Factor

12 0.40, SHGC 0.19, VT 0.28 c) LowE366-Argon-LowE I89: Overall Thickness 3/4 inch, U-Factor 0.39, SHGC 0.21, VT 0.47 c. Glazing: Silicone bedding on exterior surfaces and glazing seal on the interior of the panel. d. Simulated Divided Lites: Sculpted profile as selected. 4. Locking Hardware and Handles: Manufacturer's standard minimal one piece handle and exterior locking hardware. a. Provide with standard two point lock system secures large sliding panels with locking hardware located on the primary sliding panel. b. Provide with optional three point lock system available for systems 8 feet or taller with locking hardware located on the primary sliding panel. c. Handle Finish: 1) Brushed Satin Aluminum color. 2) Brushed Satin Bronze color. d. Provide panel handle height centered at 36 inches (914 mm) from bottom of panel. 5. Rolling Hardware: Manufacturer's standard rolling hardware integrated with engineered head track, side jambs and threshold frame system. a. Rolling Hardware: 1) Nylon polyamide plastic wheels. 2) Stainless steel wheels. b. Threshold: 1) Standard Self-draining Weather Resistant Sill with interior stop height options for all weather conditions. 2) Flush sill. 3) Ramp sill. 4) ADA Compliant ramp sill. 6. Aluminum Finish: Provide same finishes on inside and outside. a. Clear anodized c. White paint. d. Two coat 70 percent Kynar finish with color as selected from manufacturer range of finishes. e. Two coat 70 percent Kynar finish with custom color. f. Decoral wood grain finish with color as selected. 7. Threshold Finish: a. Clear anodized. 8. Screen and Blind: Provide horizontal, retractable non-pleated insect and solar control screen and blind system with fingertip operation, load balancing and tensioning adjustment. a. Screen Mechanism: 1) Stand alone type. 2) Concealed within frame and integrated with door system. b. Operation: 1) Single function for blinds up to 12 feet (3.65 m).wide and 10 feet (3.04 m) tall. 2) Double function for blinds up to 24 feet (7.31 m) wide and 10 feet (3.04 m) tall. 3) Multi-function screen and blind system up to 24 feet (7.31 m) wide and 7 feet 6 inches (2.29 m) tall. c. Screen Mesh: Fiberglass/PVC mesh as selected from manufacturer's available selection for: 1) Insect protection. 2) Control heat gain or loss

13 3) UV protection. 4) Projector screen. d. Finish: 1) Anodized finish in manufacturer's standard color 2) Anodized finish in custom color. 3) Wood veneer from manufacturer's standard selections. E. Aluminum Wood Multi Slide Doors: Hybrid panel construction of 1-3/4 inch thick extruded aluminum and 1/2 inch thick solid wood on the interior. 1. Configuration: a. Complete sliding door system including head, side jambs, thresholds and aluminum sliding panels to sizes indicated on the Drawings. b. Non-Pocket Configurations: Complete sliding door system including head, side jambs, thresholds and aluminum sliding panels to the following sizes. 1) 3 Panels OXX or XXO Maximum Frame Width 23 feet 9-3/4 inches by Maximum Frame Height 12 foot 3-1/16 inches. 2) 4 Panels OXXX or XXXO or OX XO Maximum Frame Width 31 feet 6-3/4 inches by Maximum Frame Height 12 foot 3-1/16 inches. 3) 5 Panels OXXXX or XXXXO Maximum Frame Width 39 feet 3-3/4 inches by Maximum Frame Height 12 foot 3-1/16 inches 4) 6 Panels OXXXXXX or XXXXXXO or OXX XXO Maximum Frame Width 47 feet 1-1/16 inches by Maximum Frame Height 12 foot 3-1/16 inches. c. Pocket Configurations: Complete sliding door system including head, side jambs, thresholds and aluminum sliding panels to the following sizes. 1) 1 Panel PX or XP Maximum Frame Width 16 feet 4 inches by Maximum Frame Height 12 feet 3-1/16 inches. 2) 2 Panels PXX or XXP or PX XP Maximum Frame Width 24 feet 5/16 inches by Maximum Frame Height 12 feet 3-1/16 inches. 3) 3 Panels PXXX or XXXP Maximum Frame Width 31 feet 8-5/8 inches by Maximum Frame Height 12 foot 3-1/16 inches. 4) 4 Panels PXXXX or XXXXP or PXX XXP Maximum Frame Width 39 feet 4-15/16 inches by Maximum Frame Height 12 foot 3-1/16 inches. 5) 5 Panels PXXXXX or XXXXXP Maximum Frame Width 47 feet 1-1/4 inches by Maximum Frame Height 12 foot 3-1/16 inches. 6) 6 Panels PXXXXXX or XXXXXXP or PXXX XXXP Maximum Frame Width 54 feet 9-9/16 inches by Maximum Frame Height 12 feet 3-1/16 inches. 2. Frame and Panels: Complete folding door system including head, side jambs, thresholds and aluminum panels to sizes indicated on the Drawings. a. Panel: Thermally broken, extruded aluminum stile and rail panels with standard one lite. 1) Stile and Rail 3-5/8 inches (92 mm). b. Frame and Sill: Extruded aluminum. 1) Frame width: inches ( mm). c. Weatherstripping: Weather seal inserted in frame and sill to provide perimeter seal, as well as between door panels. Color is dark bronze. d. Interior Wood Species: Provide with matching solid wood glazing stops. 1) Vertical grain Douglas Fir. 2) Okoume mahogany. 3) Custom species from manufacturer standard species. e. Interior Wood Finish: Unfinished, ready for paint or stain. 3. Glass: All glass to comply with safety glazing requirements of ANSI Z97.1 and CPSC 16CFR a. Type: Cardinal dual glazed low-e glass. 1) Insulated glass with a 3/4 inch (19 mm) overall thickness. b. Glass:

14 1) Air Filled: a) Clear-Air-Clear: Overall Thickness 3/4 inch, U-Factor 0.66, SHGC 0.59, VT 0.62 b) LowE180-Air-Clear: Overall Thickness 3/4 inch, U-Factor 0.54, c) LowE272-Air-Clear: Overall Thickness 3/4 inch, U-Factor 0.53, d) LowE366-Air-Clear: Overall Thickness 3/4 inch, U-Factor 0.52, SHGC 0.23, VT ) Argon Filled: a) Clear-Argon-Clear: Overall Thickness 3/4 inch, U-Factor 0.63, SHGC 0.59, VT 0.62 b) LowE180-Argon-Clear: Overall Thickness 3/4 inch, U-Factor 0.50, c) LowE272-Argon-Clear: Overall Thickness 3/4 inch, U-Factor 0.49, d) LowE366-Argon-Clear: Overall Thickness 3/4 inch, U-Factor 0.48, SHGC 0.22, VT 0.49 e) Solarban SB60-Argon-Clear: Overall Thickness 3/4 inch, U-Factor 0.49, SHGC 0.32, VT ) Argon Filled with room side LowE I89. a) LowE272-Argon-LowE I89: Overall Thickness 3/4 inch, U-Factor 0.45, SHGC 0.32, VT 0.53 b) LowE240-Argon-LowE I89: Overall Thickness 3/4 inch, U-Factor 0.45, SHGC 0.20, VT 0.29 c) LowE366-Argon-LowE I89: Overall Thickness 3/4 inch, U-Factor 0.45, SHGC 0.22, VT 0.48 c. Glazing: Silicone bedding on exterior surfaces and glazing seal on the interior of the panel. d. Simulated Divided Lites: Sculpted profile as selected. 4. Locking Hardware and Handles: Manufacturer's standard minimal one piece handle and exterior locking hardware. a. Provide with standard two point lock system secures large sliding panels with locking hardware located on the primary sliding panel. b. Provide with optional three point lock system available for systems 8 feet or taller with locking hardware located on the primary sliding panel. c. Handle Finish: 1) Brushed Satin Aluminum color. 2) Brushed Satin Bronze color. d. Provide panel handle height centered at 36 inches (914 mm) from bottom of panel. 5. Rolling Hardware: Manufacturer's standard rolling hardware integrated with engineered head track, side jambs and threshold frame system. a. Rolling Hardware: 1) Nylon polyamide plastic wheels. 2) Stainless steel wheels. b. Threshold: 1) Standard Self-draining Weather Resistant Sill with interior stop height options for all weather conditions. 2) Flush sill. 3) Ramp sill. 4) ADA Compliant ramp sill. 6. Aluminum Finish: Provide same finishes on inside and outside. a. Clear anodized c. White paint

15 d. Two coat 70 percent Kynar finish with color as selected from manufacturer range of finishes. e. Two coat 70 percent Kynar finish with custom color. f. Decoral wood grain finish with color as selected. 7. Threshold Finish: a. Clear anodized. 8. Screen and Blind: Provide horizontal, retractable non-pleated insect and solar control screen and blind system with fingertip operation, load balancing and tensioning adjustment. a. Screen Mechanism: 1) Stand alone type. 2) Concealed within frame and integrated with door system. b. Operation: 1) Single function for blinds up to 12 feet (3.65 m).wide and 10 feet (3.04 m) tall. 2) Double function for blinds up to 24 feet (7.31 m) wide and 10 feet (3.04 m) tall. 3) Multi-function screen and blind system up to 24 feet (7.31 m) wide and 7 feet 6 inches (2.29 m) tall. c. Screen Mesh: Fiberglass/PVC mesh as selected from manufacturer's available selection for: 1) Insect protection. 2) Control heat gain or loss. 3) UV protection. 4) Projector screen. d. Finish: 1) Anodized finish in manufacturer's standard color 2) Anodized finish in custom color. 3) Wood veneer from manufacturer's standard selections. F. Aluminum Wood Slider: Hybrid panel construction of 1-3/4 inch thick extruded aluminum and 1/2 inch thick solid wood on the interior. 1. Configuration: a. Complete sliding door system including head, side jambs, thresholds and aluminum sliding panels to sizes indicated on the Drawings. b. Non-Pocket Configurations: Complete sliding door system including head, side jambs, thresholds and aluminum sliding panels to the following sizes. 1) 2 Panels OX or XO Maximum Frame Width 23 feet 9-3/4 inches by Maximum Frame Height 12 foot 3-1/16 inches. 2. Frame and Panels: Complete folding door system including head, side jambs, thresholds and aluminum panels to sizes indicated on the Drawings. a. Panel: Thermally broken, extruded aluminum stile and rail panels with standard one lite. 1) Stile and Rail 3-5/8 inches (92 mm). b. Frame and Sill: Extruded aluminum. 1) Frame width: inches ( mm). c. Weatherstripping: Weather seal inserted in frame and sill to provide perimeter seal, as well as between door panels. Color is dark bronze. d. Interior Wood Species: Provide with matching solid wood glazing stops. 1) Vertical grain Douglas Fir. 2) Okoume mahogany. 3) Custom species from manufacturer standard species. e. Interior Wood Finish: Unfinished, ready for paint or stain. 3. Glass: All glass to comply with safety glazing requirements of ANSI Z97.1 and CPSC 16CFR

16 a. Type: Cardinal dual glazed low-e glass. 1) Insulated glass with a 3/4 inch (19 mm) overall thickness. b. Glass: 1) Air Filled: a) Clear-Air-Clear: Overall Thickness 3/4 inch, U-Factor 0.66, SHGC 0.59, VT 0.62 b) LowE180-Air-Clear: Overall Thickness 3/4 inch, U-Factor 0.54, c) LowE272-Air-Clear: Overall Thickness 3/4 inch, U-Factor 0.53, d) LowE366-Air-Clear: Overall Thickness 3/4 inch, U-Factor 0.52, SHGC 0.23, VT ) Argon Filled: a) Clear-Argon-Clear: Overall Thickness 3/4 inch, U-Factor 0.63, SHGC 0.59, VT 0.62 b) LowE180-Argon-Clear: Overall Thickness 3/4 inch, U-Factor 0.50, c) LowE272-Argon-Clear: Overall Thickness 3/4 inch, U-Factor 0.49, d) LowE366-Argon-Clear: Overall Thickness 3/4 inch, U-Factor 0.48, SHGC 0.22, VT 0.49 e) Solarban SB60-Argon-Clear: Overall Thickness 3/4 inch, U-Factor 0.49, SHGC 0.32, VT ) Argon Filled with room side LowE I89. a) LowE272-Argon-LowE I89: Overall Thickness 3/4 inch, U-Factor 0.45, SHGC 0.32, VT 0.53 b) LowE240-Argon-LowE I89: Overall Thickness 3/4 inch, U-Factor 0.45, SHGC 0.20, VT 0.29 c) LowE366-Argon-LowE I89: Overall Thickness 3/4 inch, U-Factor 0.45, SHGC 0.22, VT 0.48 c. Glazing: Silicone bedding on exterior surfaces and glazing seal on the interior of the panel. d. Simulated Divided Lites: Sculpted profile as selected. 4. Locking Hardware and Handles: Manufacturer's standard minimal one piece handle and exterior locking hardware. a. Provide with standard two point lock system secures large sliding panels with locking hardware located on the primary sliding panel. b. Provide with optional three point lock system available for systems 8 feet or taller with locking hardware located on the primary sliding panel. c. Handle Finish: 1) Brushed Satin Aluminum color. 2) Brushed Satin Bronze color. d. Provide panel handle height centered at 36 inches (914 mm) from bottom of panel. 5. Rolling Hardware: Manufacturer's standard rolling hardware integrated with engineered head track, side jambs and threshold frame system. a. Rolling Hardware: 1) Nylon polyamide plastic wheels. 2) Stainless steel wheels. b. Threshold: 1) Standard Self-draining Weather Resistant Sill with interior stop height options for all weather conditions. 2) Flush sill. 3) Ramp sill. 4) ADA Compliant ramp sill. 6. Aluminum Finish: Provide same finishes on inside and outside

17 2.3 FABRICATION a. Clear anodized c. White paint. d. Two coat 70 percent Kynar finish with color as selected from manufacturer range of finishes. e. Two coat 70 percent Kynar finish with custom color. f. Decoral wood grain finish with color as selected. 7. Threshold Finish: a. Clear anodized. 8. Screen and Blind: Provide horizontal, retractable non-pleated insect and solar control screen and blind system with fingertip operation, load balancing and tensioning adjustment. a. Screen Mechanism: 1) Stand alone type. 2) Concealed within frame and integrated with door system. b. Operation: 1) Single function for blinds up to 12 feet (3.65 m).wide and 10 feet (3.04 m) tall. 2) Double function for blinds up to 24 feet (7.31 m) wide and 10 feet (3.04 m) tall. 3) Multi-function screen and blind system up to 24 feet (7.31 m) wide and 7 feet 6 inches (2.29 m) tall. c. Screen Mesh: Fiberglass/PVC mesh as selected from manufacturer's available selection for: 1) Insect protection. 2) Control heat gain or loss. 3) UV protection. 4) Projector screen. d. Finish: 1) Anodized finish in manufacturer's standard color 2) Anodized finish in custom color. 3) Wood veneer from manufacturer's standard selections. A. Sizes and Configurations: Fabricate to sizes and configurations indicated on the Drawings. Verify opening sizes by field measurement prior to completing fabrication. B. Verify sliding direction for opening units. C. Fabricate with manufacturer's non-integral nail fin for use in conjunction with standard flashing, weather resistant barriers and compatible sealants. PART 3 EXECUTION 3.1 EXAMINATION A. Do not begin installation until substrates have been properly prepared. B. Verify that the maximum deflection of the header with the live load does not exceed the lesser of L/720 of the span and 1/4 inch. Structural support for lateral loads including both wind load and when the panels are stacked open) must be provided. C. Verify that dimensions of rough opening will fit the net frame dimensions of door system; verify that rough openings are level, plumb, and square, with no unevenness in the floor

18 D. If substrate preparation is the responsibility of another installer, notify Architect of unsatisfactory preparation before proceeding. 3.2 PREPARATION A. Clean surfaces thoroughly prior to installation. B. Prepare surfaces using the methods recommended by the manufacturer for achieving the best result for the substrate under the project conditions. 3.3 INSTALLATION A. Install in accordance with manufacturer's instructions. B. Properly flash and waterproof around the perimeter of the opening and frame. Adequate overhangs to prevent the effects of sheeting water from above are recommended. C. Provide adequate anchorage devices. Securely fit frame in place, level, straight, plumb and square. Install frame in proper elevation, plane and location, and in proper alignment with other work. Head section of frame must be installed with a 1/8 inch upward crown at the center of the opening. D. If necessary for tracks recessed into finish floors, drill weep holes in the floor track and provide drain connectors to ensure water can escape from the tracks. E. Ensure doors are adjusted for proper operation. F. For products requiring field finishing, field as specified in Section Painting and Coating; seal and finish promptly after installation and no more than seven days and prior to exposure to weather. G. Install the screen system following the manufacturer's recommendations and installation instructions. 3.4 PROTECTION A. Protect installed products until completion of project. B. Protect installed product from construction activities, particularly thresholds and floor channels. C. Touch-up, repair or replace damaged products before Substantial Completion. 3.5 SCHEDULES A. : B. : END OF SECTION