If you or your painting contractor are doing interior painting, be advised that disposal of empty cans in the Montsalas dumpster area (or IN the

Transcription

1 If you or your painting contractor are doing interior painting, be advised that disposal of empty cans in the Montsalas dumpster area (or IN the dumpster) is strictly prohibited. Residents are required to notify their contractors.

2 P R E M I U M S I N C E W O O D C A R E DESCRIPTION Recommended Uses: Cabot Solid Color Decking Stains with TEFLON Surface Protector are extremely durable exterior stains for use on all wood decking, outdoor furniture and fencing, as well as cement patios and walkways. This exceptionally long-lasting, 100% acrylic finish is also water repellent and fade resistant. This revolutionary formula is reinforced with TEFLON Surface Protector. It will resist scuffing, and oil and grease will wash off easily with mild detergent and water. Solid Color Decking Stains are ideal for use on most types of lumber including redwood, cedar, cypress, pine and fir, as well as pressure-treated wood. Solid Color Decking Stain is easy to apply, dries quickly and cleans up with soap and water. They provide excellent adhesion to new, previously stained or painted surfaces which are in a clean, sound condition. For use on: Decks, fencing, wood patios, porches, outdoor furniture, steps, railings and cement patios. Composition: Richly pigmented, opaque, 100% acrylicbased stain. Finish: Dries to a uniform, durable, low-lustre finish. TECHNICAL DATA Solid Color Decking Stains #1800 Series with Teflon Surface Protector Colors: Available in 6 ready-mixed colors, including white. Additional colors may be achieved with four tint bases White Base #1801, Neutral Base #1806, Deep Base #1807 and Medium Base #1808. Special shades may be ordered in quantities of 50 gallons or more at an extra charge of 25%. Tinting: White, Neutral, Medium and Deep Bases may be tinted with compatible universal colorants. Coverage: Approximately square feet per gallon. These rates will vary depending upon the porosity and type of surface. Spread rates will increase when applying a second coat. Packaging/Containers: Available in one-gallon containers. Restrictions: Do not thin. Do not apply in direct sunlight, to hot surfaces or when the air and surface temperature is below 50 F or may fall below 50 F. Do not apply over wet surfaces or when rain is imminent. Protect stored containers from freezing. Do not use Neutral, Medium or Deep Bases without the addition of universal colorants. Not intended for siding surfaces. For siding, use O.V.T. Solid Color Acrylic Stain or The Finish. Not intended for interior surfaces. For exterior use only. Weathered and/or reconditioned wood surfaces require an application of Cabot Problem-Solver Oil Primer prior to topcoating. Do not apply over freshly applied Decking Stain (#1400 Series) or Cabot Clear Solution. Either strip these coatings or wait one year for the coating to weather sufficiently. TECHNICAL DATA Environmental Impact: This product is in compliance with V.O.C. (Volatile Organic Compounds) requirements for Specialty Architectural Coatings. Call Cabot s Technical Services & Support for additional information pertaining to current V.O.C. rulings. Cleanup and Disposal: Clean brushes and equipment using warm water with soap or detergent. Close container when not in use. Dispose of empty cans or unused portion in accordance with local, state and federal regulations. Material Safety Data Sheet (MSDS) available upon request. Physical and Chemical Data: Drying Time: Dries to touch in approximately 1 hour. Recoat after 4-6 hours. Allow 24 hours dry time before walking or placing furniture on newly stained surfaces. Weight: pounds per gallon. Flash Point: Not applicable (water-based product). Film Thickness: 3 mils. Shelf Life: At least ten years in closed original containers at room temperature. Mildew Resistant: Yes % Solids (weight): % Solids (volume): % Pigment (weight): Viscosity: Kreb units (Tinted), Stormer Viscometer at 77 F (25 C). Pigment Type: Titanium Dioxide, Iron Oxide Pigments, Light Fast Organic Pigments, Silica. Vehicle Type: 100% acrylic polymer system. Solvent Type: Water V.O.C. Content: Maximum of 250 grams/liter (2.079 lbs/gal.). Gloss: maximum with a 60 glossmeter. TECHNICAL DATA SOLID COLOR DECKING STAINS #1800 SERIES Teflon is a registered trademark of E. I. du Pont de Nemours and Company.

3 Solid Color Decking Stains #1800 Series with Teflon Surface Protector APPLICATION Surface Preparation: Proper surface preparation is the key to maximum product performance. The durability of this product can be impaired by an unsound or poorly prepared surface. It is very important that the surface be clean of all dirt and sufficiently dry. (Moisture content must be below 15%, or wood must be exposed to dry weather a minimum of 3 to 5 days.) Previously painted, stained or weathered wood surfaces should be scrubbed with Cabot Problem-Solver Wood Cleaner and a stiff bristle brush. Cabot Problem-Solver Wood Brightener can be used to easily remove nail and metal rust stains, stains caused by extractive bleeding, and renew the wood s appearance. Use Cabot Problem-Solver Strippers (8004 & 8005) to safely remove all stains and paints from wood surfaces in order to prevent product failure and to create a sound surface for maximum adhesion. Power washing has proven to be effective in removing the surface layer of all loose wood fibers, dirt, chalky residue, flaking paint and stain and other foreign matter. Weathered Wood: Reconditioned wood requires the use of Cabot Problem-Solver Oil Primer prior to topcoating with Cabot Solid Color Decking Stain. New Masonry: Allow new masonry surfaces to cure for 30 days before coating with Solid Color Decking Stain. Application of Coating: Stirring: Stir thoroughly before and occasionally while using. If the job requires more than one batch, blend them together. Methods: Apply evenly with a brush, roller, paint pad or spray. When rolling or spraying, always backbrush immediately to ensure uniformity. Best results can be obtained by using a high-quality nylon brush. To avoid non-uniform appearances start at one edge of a few boards and continue all the way to the end. Spray Application: Recommended tip sizes and adjustments for spray application are at PSI with a fan width of 5-8 inches; one gun. When using HVLP spray equipment, see manual for proper set-up instructions. Number of Coats: Two coats are highly recommended for maximum durability. Some colors may require additional coats for complete hiding. Precautions: This product performs best when applied to decks that are at least 18 inches above grade. Floor coatings can become slippery when wet. Use extreme caution when walking on a surface that is wet, especially when temperatures fall below freezing. NOTICE: Dark colors derived from tinting Neutral Base #1806 may show scuff or scratch marks more easily than light colors. In addition, dark colors absorb and retain more heat than light colors when exposed to severe sunlight. AVAILABILITY Cabot Wood Care Products are sold throughout the United States, Canada, Australia, Ireland, Chile and the Caribbean. For a list of Cabot dealer locations, please contact Cabot s Technical Services & Support. WARRANTY When applied according to the directions on the label, if this Cabot product is proved to be defective after purchase, Samuel Cabot Inc. will furnish any necessary additional product free of charge or will refund the purchase price at the company s option. Cracking, peeling and blistering that result from structural problems are not covered under this warranty. This warranty does not include labor or cost of labor for the application of the product. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. MAINTENANCE Minimal because Cabot Solid Color Decking Stains will resist scuffing, and are oil and grease resistant. Allow the coating to cure 7 days before washing. Depending upon exposure or wear, evaluate restaining needs every 2-3 years. TECHNICAL SERVICES For additional technical information, product line color cards, fan decks, and liquid product samples, see your specialized Cabot Dealer or call the Cabot Wood Care Specialists in Technical Services & Support toll-free at US-STAIN ( ). FILING SYSTEMS For complete model specifications and technical data on all Cabot products, visit the Cabot Home Page at: P R E M I U M S I N C E W O O D C A R E Samuel Cabot Incorporated: Corporate Headquarters 100 Hale Street Newburyport, MA Tel.: US-STAIN ( ) Fax: # printed 4/03

4 1240 ACRY-SHIELD 100% Acrylic Exterior Flat Paint Product Description A premium quality 100% acrylic exterior flat finish that provides a durable, weather resistant finish for exterior wood, fiber cement board, stucco, concrete, masonry, and other properly prepared surfaces. When properly applied, qualifies for Kelly-Moore s limited lifetime warranty. Excellent for commercial and residential application. Performance Features Excellent Durability Excellent Adhesion Cold Weather Application down to 38 degrees Mildew Resistant Meets Requirements for Manufactured Siding Fade & Chalk Resistance Low Odor & VOC Compliance & Certification MPI Approved Product List #10, #16 Meets MPI GPS-1 & GPS-2 Meets Green Seal GS-11 VOC Limits Meets LEED EQ Credit 4.2 VOC Limits Green Wise Certified Meets CARB VOC Limits Meets SCAQMD VOC Limits Meets National AIM VOC Limits Product Specifications Resin Type: 100% Acrylic Color Range: White, ready-mixed and custom tinted colors Finish: Flat 60 (MPI Gloss Level 1) Drying Time: (75º F. & 50% R.H.) To touch: 1 hour To recoat: 4 hours. Practical Coverage: Approx sq ft/gallon Recommended Dry Film Thickness: Wet: mils/coat Dry: mils/coat Weight per Gallon: 12.1 lbs. Solids by Weight: 58% Solids by volume: 40% Shelf Life: 2 years (unopened containers) Sizes: Five gallon, one gallon & quarts V.O.C. <50 Grams per liter Clean-up: Water PAINTING AND COATING Surface Preparation General: All surfaces must be cured, firm, dry and cleaned free of dust, dirt, oil, grease, wax, chalky or loose paint, rust, loose mill scale, bond breakers and curing compounds, efflorescence, asphalt stains, mildew or any other contamination or condition that would adversely affect the performance of the coating. Sand glossy, glazed or dense surfaces*. Fill holes and surface irregularities with a suitable patching compound to match the surface profile. *See warning for existing leaded paint under Precautions. Previously Painted Surfaces: Spot prime bare or patched areas or prime entire surface, as required. Lightly-chalked painted surfaces should be primed with Kelly-Moore 239 Kel-Bond II or other chalk binding primer. Loose paint and medium to heavy chalk must be removed. Pre-Primed Manufactured Siding: Must be clean and dry. Spot prime damaged areas with appropriate primer. New Wood: Follow general surface preparation guidelines. To insure maximum adhesion, the substrate must be free of all dead wood fibers. Prime with the specified primer or self-prime. New Masonry, Concrete & Stucco: Follow general surface preparation guidelines. New Concrete or Stucco should be allowed to cure for 30 days. Prime with the specified primer. Continued Next Page KELLY-MOORE PAINT COMPANY INC. 987 COMMERCIAL ST. SAN CARLOS, CA Technical Assistance 888-MR-PAINT

5 1240 ACRY-SHIELD (cont.) New Ferrous Metal: Follow general surface preparation guidelines. Remove all loose rust, mill scale, or deteriorated previously applied coatings by Hand Tooling (SSPC-SP-2) or Power Tool Cleaning (SSPC-SP-3). Prime with specified primer immediately after cleaning. New Aluminum & Galvanized Metal: Wash thoroughly with TSP or other suitable cleaner/degreaser to remove oil and other contaminants. Rinse thoroughly. Prime with the specified primer. System Recommendations New Wood: PRIMER: 255 Acry-Shield 100% Acrylic Exterior Wood Primer 220 Weather Shield Exterior Alkyd Primer 285 Kel-Bond Ultra Waterborne High Build Bonding Primer/Sealer Self Priming (2 Coats minimum incl. finish)* *Staining woods such as cedar and redwood should be primed with 255 or 220. Cement-Fiber Board (Pre-primed): PRIMER: Not required New Cement-Fiber Board: PRIMER: 247 Acry-Shield 100% Acrylic Exterior Masonry Primer Hardboard (Pre-primed): PRIMER: Not required. Prime bare or damaged areas with 255 Acry-Shield 100% Acrylic Exterior Wood Primer New Concrete, Stucco & Masonry: PRIMER: 247 Acry-Shield 100% Acrylic Exterior Masonry Primer Self Prime (2 Coats minimum incl. finish) PAINTING AND COATING New Ferrous Metal: PRIMER: 1725 Kel-Guard Acrylic Metal Primer New Aluminum & Galvanized Metal: PRIMER: 1725 Kel-Guard Acrylic Metal Primer 287 Kel-Bond Adhesion Plus FINISH: 1240 Acry-Shield 100% Acrylic Exterior Flat Paint Application: Brush, Roll, or Spray Brush: Use synthetic bristle brush. Roller: Use 1/2 to 1 nap quality roller cover, depending on surface profile. Spray: Airless sprayer is recommended. Use.017 to.021 orifice tip. Not recommended for HVLP or Conventional sprayers. Do not apply when material, air, and/or surface temperature is below 38 F or above 90 F. Do not apply when rain is imminent or the temperature is less than 5 F. above the dew point. To avoid heat blisters, especially in darker colors, avoid painting in direct sun at all temperatures. Stir thoroughly before and during use. Maintain a wet edge to avoid lap marks. Store at room temperature. Keep from freezing. Thinning Apply at can consistency. If thinning is necessary to maintain workability, do not exceed one-half pint of water per gallon. Continued Next Page KELLY-MOORE PAINT COMPANY INC. 987 COMMERCIAL ST. SAN CARLOS, CA Technical Assistance 888-MR-PAINT Page 2

6 1240 ACRY-SHIELD (cont.) Precautions WARNING! If you scrape, sand or remove old paint from any surface, you may release lead dust. LEAD IS TOXIC. EXPOSURE TO LEAD DUST CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE, ESPECIALLY IN CHILDREN. PREGNANT WOMEN SHOULD ALSO AVOID EXPOSURE. Wear a NIOSHapproved respirator to control lead exposure. Carefully clean up with a wet mop or HEPA vacuum. Before you start, find out how to protect yourself and your family by contacting the U.S. EPA/Lead Information Hotline at LEAD (5323) or log on to Avoid contact with eyes, skin and clothing. Do not take internally. Wash thoroughly after handling. Close container after each use. For additional safety information consult the Material Safety Data Sheet for this product. USE ONLY WITH ADEQUATE VENTILATION. KEEP OUT OF REACH OF CHILDREN. Proper Disposal For proper disposal of excess material, please contact your local city or county waste management agency. Limited Warranty: The statements made on this bulletin, product labels or by any of our agents concerning this material are given for information only. They are believed to be true and accurate and are intended to provide a guide to approved construction practices and materials. As workmanship, weather, construction equipment, quality of other materials and other variables affecting results are all beyond our control, Kelly-Moore Paint Company, Inc., does not make nor does it authorize any agent or representative to make any warranty of MERCHANTABILITY OR FITNESS for any purpose or any other warranty, guarantee or representation, expressed or implied, concerning this material except that it conforms to Kelly-Moore's quality control standards. Any liability whatsoever of Kelly-Moore Paint Company, Inc. to the buyer or user of this product is limited to the purchaser's cost of the product itself PAINTING AND COATING KELLY-MOORE PAINT COMPANY INC. 987 COMMERCIAL ST. SAN CARLOS, CA Technical Assistance 888-MR-PAINT Page 3

7 1128 KEL-SEAL TERPOLYMER 100% Acrylic Elastomeric Coating (Smooth) Product Description A premium quality, exterior, 100% acrylic, smooth elastomeric coating. Features waterproofing, durability, excellent film strength, elasticity, elongation, bridging of hairline cracks and chalk resistant properties. Designed for concrete, concrete block, stucco and masonry surfaces. Suitable for use on primed wood and metal. Excellent for commercial and residential application. Compliance - Performance - Certification MPI Approved Product List #113 Meets MPI GPS-1 Meets Green Seal GS-11 VOC Limits Meets CARB VOC Limits Meets SCAQMD VOC Limits Meets National AIM VOC Limits Performance Features Excellent Durability Prevents Moisture Penetration Bridges Hairline Cracks Excellent Weather Resistance 300% Elongation Self Priming on Cured Concrete & Stucco Resistant to Mildew, Fungus, and Algae Product Specifications Resin Type Acrylic Color Range White & custom tinted colors Finish Flat 60 (MPI GL 1) Drying Time (75º F. & 50% R.H.) To touch: 2 hours To recoat: 24 hours Practical Coverage Approx sq ft/gallon Recommended Dry Film Thickness 8-10 mils per coat Weight Per Gallon 10.5 lbs. Solids By Weight 60% Solids By Volume 50% Water Vapor Permeance 12 recommended dry film thickness Shelf Life 2 years (unopened containers) Sizes One & five gallon containers V.O.C. <50 Grams per liter Clean Up Water. Product Analysis (by weight) PIGMENT COMPOSITION 28% Titanium Dioxide: 6% Silicates: 20% Calcium Carbonate: 2% VEHICLE COMPOSITION 72% Acrylic Resin: 31% Water, Surfactants, Defoamers: 41% Surface Preparation WARNING! If you scrape, sand or remove old paint from any surface, you may release lead dust. LEAD IS TOXIC. EXPOSURE TO LEAD DUST CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE, ESPECIALLY IN CHILDREN. PREGNANT WOMEN SHOULD ALSO AVOID EXPOSURE. Wear a NIOSH-approved respirator to control lead exposure. Carefully clean up with a wet mop or HEPA vacuum. Before you start, find out how to protect yourself and your family by contacting the U.S. EPA/Lead Information Hotline at LEAD (5323) or log on to General: All surfaces must be cured, firm, dry and cleaned free of dust, dirt, oil, grease, wax, chalky or loose paint, rust, loose mill scale, bond breakers and curing compounds, efflorescence, asphalt stains, mildew or any other contamination or condition that would adversely affect the performance of the coating. Sand glossy, glazed or dense surfaces. Fill holes and surfaces irregularities with a suitable patching compound to match the surface profile. All non-structural cracks up to 1/32" are to be patched with Kel-Seal Elastomeric Sealant. Cracks over 1/32" are to be repaired with the appropriate Kel-Seal Patching System. Minor surface imperfections and irregularities are to be filled with the appropriate Kel-Seal sealant. Apply sealants and patching compounds according to printed directions to match the finish texture and surface profile. Previously painted surfaces with only light chalk should be primed with 239 Kel-Bond II. Continued next page KELLY-MOORE PAINT COMPANY INC. 987 COMMERCIAL ST. SAN CARLOS, CA Technical Assistance MR-PAINT Page 1

8 1128 KEL-SEAL (cont.) Heavily chalked or powdery surfaces should be made sound by sandblasting or other appropriate method and then primed with 239 Kel-Bond II. Heavily textured or porous concrete block should be filled first to achieve a relatively smooth surface, free of voids, with one coat of Kel-Seal Acrylic Terpolymer Coating rolled into the surface for best filling action. System Recommendations Concrete Block (CMU): PRIMER: 1128 Kel-Seal Terpolymer Concrete, Stucco & Masonry: PRIMER: 247 Acry-Shield 100% Acrylic Masonry Primer Stucco Seal 2 coats 1128 at recommended DFT Wood & Hardboard: PRIMER: 255 Acry-Shield 100% Acrylic Primer Metal (ferrous, galvanized, or aluminum): PRIMER: 1725 Acry-Shield 100% Acrylic Metal Primer Previously Painted, Lightly Chalked Surfaces: PRIMER: 239 Kel-Bond II FINISH: 1128 Kel-Seal Acrylic Terpolymer Application Brush, roll or spray. Do not apply when material, air, and/or surface temperature is below 50 F or if rain is expected within 72 hours. Extremely high or low temperature or periods of high relative humidity may adversely affect dry time. Two coats are required for optimum performance. Stir thoroughly before and during use. Maintain a wet edge to avoid lap marks. In order to achieve a waterproof wall, the coating must be applied in a continuous unbroken film, free of pinholes and voids. When sprayed on rough or porous surfaces, back-rolling procedure is recommended to fill holes more efficiently. This product must be applied at the recommended film thickness to achieve proper cure. Special Precautions: Always test for compatibility and adhesion when used over previously coated surfaces. When applied by roller, minimize roller marks by finishing roller passes all in downward direction. Clean equipment thoroughly with water immediately after use. Note: It is difficult to achieve a uniform finish with mastic paints of this type. Therefore, an experienced applicator is required. Uniformity and texture pattern are affected by film thickness, substrate, application method and climatic conditions: therefore, the manufacturer assumes no responsibility for the finished appearance. Thinning Apply at can consistency. If thinning is necessary to maintain workability, do not exceed one-half pint of water per gallon. Warranty KELLY-MOORE PAINT COMPANY, INC. warrants the effectiveness of 1128 Kel-Seal Acrylic Terpolymer Coating as a water repellent coating on above grade, vertical, exterior masonry, concrete and stucco surfaces to the extent of material replacement only when applied properly and in accordance with the manufacturer's printed literature. If requested at least 72 hours prior to application, the manufacturer will provide a five year written limited warranty with the conditions stated herein. Precautions Avoid contact with eyes, skin and clothing. Do not take internally. Wash thoroughly after handling. Close container after each use. Protect from freezing. For additional safety information consult the Material Safety Data Sheet for this product. USE ONLY WITH ADEQUATE VENTILATION KEEP OUT OF REACH OF CHILDREN. Proper Disposal For proper disposal of excess material, please contact your local city or county waste management agency. Mildew and Algae: This paint has been formulated to be mildew and algae resistant, however, it will not mildew-proof the surface nor completely prevent or destroy mildew or algae. Therefore, Kelly- Moore Paint Company Inc. assumes no responsibility for mildew, fungus, or algae development. Limited Warranty: The statements made on this bulletin, product labels or by any of our agents concerning this material are given for information only. They are believed to be true and accurate and are intended to provide a guide to approved construction practices and materials. As workmanship, weather, construction equipment, quality of other materials and other variables affecting results are all beyond our control, Kelly-Moore Paint Company, Inc., does not make nor does it authorize any agent or representative to make any warranty of MERCHANTABILITY OR FITNESS for any purpose or any other warranty, guarantee or representation, expressed or implied, concerning this material except that it conforms to Kelly-Moore's quality control standards. Any liability whatsoever of Kelly-Moore Paint Company, Inc. to the buyer or user of this product is limited to the purchaser's cost of the product itself. KELLY-MOORE PAINT COMPANY INC. 987 COMMERCIAL ST. SAN CARLOS, CA Technical Assistance MR-PAINT Page 2

9 247 ACRY-SHIELD 100% Acrylic Exterior Masonry Primer Product Description A premium quality white pigmented 100% acrylic primer for concrete, masonry, stucco, plaster and fiber cement board. Forms a highly alkali resistant film and can be applied to surfaces having a ph of up to 13. Helps protect finish coats from lime burn, discoloration and efflorescence. Performs equally well under latex or alkyd finishes. Also suitable for interior application. Excellent for commercial and residential application. Performance Features Excellent Alkali Resistance Excellent Adhesion Interior/Exterior Use Cold Weather Application (>38 F) Excellent for Fiber Cement Board Low Odor and VOC Easy Soap & Water Clean Up Compliance - Performance - Certification Meets Green Seal GS-11 VOC Limits Meets LEED EQ Credit 4.2 VOC Limits Meets CARB VOC Limits Meets SCAQMD VOC Limits Meets National AIM VOC Limits Product Specifications Resin Type: 100% Acrylic Color Range: White Drying Time: (75º F. & 50% R.H.) To touch: 30 minutes To recoat Overnight Practical coverage: Approx sq ft/gallon Recommended Dry Film Thickness: Weight per Gallon: Wet: mils per coat Dry: mils per coat 9.7. lbs. Solids by Weight: 44% Solids by Volume: 33% Shelf Life: 2 years (unopened containers) Sizes: One & five gallon containers V.O.C. <100 Grams per liter Clean Up: Water Surface Preparation General: All surfaces must be cured, firm, dry and cleaned free of dust, dirt, oil, grease, wax, chalk, rust, mildew or any other contamination or condition that would adversely affect the performance of the coating. Sand glossy, dense or glazed surfaces*. New Surfaces: All surfaces should be sound, free of contamination, efflorescence or laitance and dry. Masonry and plaster should be thoroughly cured before priming. Masonry should have a moisture content of less than 12% as measured by a moisture meter. Concrete Tilt-ups must be cleaned of all bond breaker compounds via pressure washing or other effective cleaning methods. Tilt-ups that are smooth, glossy and/or dense should be sweep blasted for optimum performance. Previously Painted Surfaces: Remove any peeling, chalky or loosely adhering paint, sand to feather edges, dust clean (do not use tack rags). Sand glossy finishes*. *See warning for existing leaded paint under Precautions. System Recommendations Masonry, Plaster, Fiberboard, etc.: PRIMER: 247 Acry-Shield 100% Acrylic Exterior Masonry Primer FINISH: Appropriate finish. Continued Next Page KELLY-MOORE PAINT COMPANY INC. 987 COMMERCIAL ST. SAN CARLOS, CA Technical Assistance 888-MR-PAINT

10 247 ACRY-SHIELD (cont.) Application: Brush, Roll, or Spray Brush: Use synthetic bristle brush. Roller: Use 3/8 to 3/4 nap quality roller cover, depending on surface profile. Spray: Airless sprayer use.015 to.017 orifice tip. For conventional or HVLP sprayers please consult sprayer manual for waterborne primers. Do not apply when material, air, and/or surface temperature is below 38 F or above 90 F. Stir thoroughly before and during use. Maintain a wet edge to avoid lap marks. Store at room temperature. Keep from freezing. Thinning Apply at can consistency. If thinning is necessary to maintain workability, do not exceed one-half pint of water per gallon. Precautions WARNING! If you scrape, sand or remove old paint from any surface, you may release lead dust. LEAD IS TOXIC. EXPOSURE TO LEAD DUST CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE, ESPECIALLY IN CHILDREN. PREGNANT WOMEN SHOULD ALSO AVOID EXPOSURE. Wear a NIOSHapproved respirator to control lead exposure. Carefully clean up with a wet mop or HEPA vacuum. Before you start, find out how to protect yourself and your family by contacting the U.S. EPA/Lead Information Hotline at LEAD (5323) or log on to Avoid contact with eyes, skin and clothing. Do not take internally. Wash thoroughly after handling. Close container after each use. For additional safety information consult the Material Safety Data Sheet for this product. USE ONLY WITH ADEQUATE VENTILATION. KEEP OUT OF REACH OF CHILDREN. Proper Disposal For proper disposal of excess material, please contact your local city or county waste management agency. Limited Warranty: The statements made on this bulletin, product labels or by any of our agents concerning this material are given for information only. They are believed to be true and accurate and are intended to provide a guide to approved construction practices and materials. As workmanship, weather, construction equipment, quality of other materials and other variables affecting results are all beyond our control, Kelly-Moore Paint Company, Inc., does not make nor does it authorize any agent or representative to make any warranty of MERCHANTABILITY OR FITNESS for any purpose or any other warranty, guarantee or representation, expressed or implied, concerning this material except that it conforms to Kelly-Moore's quality control standards. Any liability whatsoever of Kelly-Moore Paint Company, Inc. to the buyer or user of this product is limited to the purchaser's cost of the product itself. KELLY-MOORE PAINT COMPANY INC. 987 COMMERCIAL ST. SAN CARLOS, CA Technical Assistance 888-MR-PAINT Page 2