Altro Seal standard, Altro Seal slip-resistant and Altro Seal vertical

Transcription

1 Atro Sea standard, Atro Sea sip-resistant and Atro Sea vertica UV stabe poyurethane foor coating Nomina thickness 180 microns Technica and instaation data sheet September 2016 Product description FeRFA type 1 Atro Sea is a two pack; ight stabe sovent based poyurethane foor coating. Atro Sea provides a surface that has good abrasion, chemica and stain resistance. It is avaiabe in a wide range of coours or cear, and is easy to appy and fast curing. Atro Sea vertica can be appied on surfaces such as coving and was. It can aso be used as a fina sea coat to give extra chemica resistance to epoxy resin systems. Atro Sea sip-resistant variant provides a degree of sip resistance through the incorporation of a micaceous minera that ighty textures the surface. Standard coours Avaiabe in 26 standard coours and cear with options for bespoke coours. Non standard coours Safety Yeow, Safety Red. Safety Red, Safety Yeow and Back are intended for ine marking and sma areas of demarcation ony. Bright ighting and dark coours in particuar back wi highight any defects such as roer ines scratches and marring. For safety coours, ight or vibrant cooured coatings, a white undercoat shoud be used and additiona coats may be required. Safety Red, Safety Yeow and white are not incuded in Atro resins standard coour range. Bespoke non-standard coours wi be subject to additiona ead time and possiby increased cost. Typica areas of use Light duty areas Pharmaceutica Areas subject to occasiona chemica spi Craft and design rooms Advantages Easy to appy Cost effective Good chemica resistance Good scuff / abrasion resistance Fat sik finish Sustainabiity Atro s steps to sustainabiity program seeks to optimise our performance with respect to the panet s resources. Pease refer to for further information Chemica resistance Atro Sea variants offer resistance to a range of commony used chemicas. However, premature or proonged contact with chemicas (incuding water) during the curing process may give rise to discoouration, staining and variation in goss. In a cases of chemica spiage, it is essentia that the spiage is immediatey removed and the surface washed down with cean water, removing water by wet vacuum after operation. Athough some chemicas may cause discoouration, this may not affect the durabiity and integrity of the resin screed. Pease refer to Atro and FeRFA Guidance Note No.3 for further information.

2 Typica physica properties Speed of cure Light foot traffic C Fu cure 7 20 C Appication temperature 10 C to 25 C Usabe working ife C Packaging Atro Sea standard and Atro Sea vertica cooured variants are avaiabe in a 5kg, two-part composite pack. Atro Sea standard and Atro Sea vertica cear variants are avaiabe in a 4kg, two-part composite pack. Atro Sea sip-resistant cooured is avaiabe in a 5kg, three-part composite pack. Coverage Atro Sea standard cooured and Atro Sea vertica cooured 1st coat 30m² per 5kg unit 2nd coat 40m² per 5kg unit Atro Sea standard cear and Atro Sea vertica cear 1st coat 25m² per 5kg unit 2nd coat 40m² per 5kg unit Atro Sea sip-resistant cooured 1st coat 30m² per 5kg unit 2nd coat 35m² per 5kg unit Materia usage is dependent upon temperature, surface profie and porosity; stated coverage rates shoud be referred to for guidance ony, and cannot be reied upon to determine exact quantities. Storage Ensure that the product is received in good order and store in a dry, frost free environment, ideay between 15 C and 20 C for at east three days before aying. Excessivey high and ow storage temperatures wi affect the aying performance of the product. Suitabe substrates Atro Sea may be appied to a variety of substrates incuding, but not imited to, concrete, poymer-modified cementitious screeds, terrazzo, 25mm marine grade pywood (consut Atro for further guidance). For a proprietary subfoor systems refer to the manufacturer for recommendations and seek further guidance from Atro. Porous and akaine substrates incuding concrete shoud be primed with Atro Sea goss singe pack. This shoud be over-coated when touch dry or within 24 hours. FeRFA, The Resin Federation, does not recommend Cacium Suphate, Anhydrite or Hemi-hydrite screeds for overayment with synthetic resin surfaces. Substrate requirements Substrates shoud be dry, structuray sound and free from contamination, friabe materias or aitance which may affect either the adhesion or penetration of the resin system. A residues of od paint coatings and dust must be removed. Substrates to achieve 26N/mm² compressive strength (BS EN ) and surface tensie strength 1.5N/mm² (BS EN ). Substrates must incude an integra effective damp proof membrane and contain residua moisture not greater than 5% by weight (75% R.H.) to (BS 8203.) Thin-bed synthetic resin systems foow the surface of the substrate, so it is essentia that the surface reguarity of fatness conforms to or exceeds (BS ) cass SR2 (+/- 5mm under a 2 metre straight edge). Any deviation from this may require a surface improver to be appied which must be suitabe to receive an epoxy resin overay. The surface profie may be refected in thinner resin fooring types. This wi affect the appearance and wear. Pease consut Atro or FeRFA Guide to the Specification and Appication of Synthetic Resin Fooring for further information.

3 Substrate preparation Surface preparation is the most vita aspect of resin fooring appication. Inadequate preparation wi ead to oss of adhesion and faiure. The substrate in question wi dictate the method of preparation. In the case of a concrete foor, preparation by dust encosed diamond foor grinder may be appropriate, or if of a sufficient area for economic reasons, shoud be ighty shot basted to eave a textured surface free from contamination. If the foor has been treated with a cementitious surface improver, then the surface shoud be prepared in accordance with the manufacturer s recommendations, or abraded with an STR machine foowed by thorough vacuuming. Treatment of oca repairs such as cracks and hoes, improvement or modification of eves and remova of high spots, shoud be undertaken prior to the fooring instaation. Pease consut Atro or FeRFA s Guide to the Specification and Appication of Synthetic Resin Fooring for further guidance. Panning Before proceeding with the instaation, carefu consideration shoud determine the best way of instaing the Atro system. Efforts shoud be made to minimise day joints and optimise the open time of the product (i.e. minimise the distance between mixing and aying). It is best to aso consider the effect of externa infuences on the fina instaation (i.e. direction of ight from windows etc.). Time spent at this stage wi be invauabe towards the success of your instaation. Instaation conditions Appy in we ventiated areas. Both the sab and air temperature shoud be between 10 C to 25 C. It is not advisabe to mix and ay poyurethane resin products outside the range 10 C to 25 C. Ambient conditions shoud be maintained at east 3 C above dew point or beow 75% R.H. during the initia stages of cure. At site temperatures beow 10 C, cure times wi be substantiay increased uness some form of externa heating is used. (Avoid using heating sources that give rise to high eves of humidity). It must be recognised that the concrete sab temperature wi generay be ower than the air temperature, often as much as 10 C, and this wi govern the rate of cure. As the resin fooring cures, in condensing conditions moisture vapour may condense onto the surface and cause booming, a permanent couding of the surface. Cod, wet or humid conditions, and imited air fow, can resut in condensation on the part cured foor. The workabiity, open-time, cure deveopment and return to traffic wi be significanty affected by ambient conditions. Mixing equipment Sow speed dri ( rpm), such as MM17 * Mixing padde, such as MR3 * A too number references reate to Refina Ltd Appication The foowing appication guide is based on aboratory and simuated site conditions. However, when instaations conditions differ appreciaby from those detaied by Atro, the performance characteristics of both mixing and aying may not be as expected. To achieve the best resuts at a times pease endeavour to estabish the correct conditions which in turn wi aow the materias to be aid effectivey, and meet your customer s expectations.

4 Product instaation Using a sow speed dri and padde thoroughy mix together the base for 30 seconds. Pour a the hardener into the premixed base and mix for a further 90 seconds. Excessivey vigorous mixing shoud be avoided as this can ead to undesirabe air entrainment. Care shoud be taken to ensure that any materia adhering to the sides, bottom and corners of the mixer is thoroughy bended in. If the mixing area is not adjacent to the aying area the time required to transfer the mixed materia wi reduce the open instaation time. Remember to aways use the correct PPE. Pour a the mixed materia into a arge roer tray, and using a ow-oss medium pie synthetic roer, distribute the materia eveny and uniformy to fuy treat the surface. Begin on the side of the main ight source and work away from the ight. Finish using a roer in the direction of the ight source to ensure that a uniform and even coverage is achieved. The apping time between units and retouching of the wet finish shoud be minimised as this may resut in roer ines and variations of the finish. The area shoud not be re-touched after 15 minutes. Roer ines are more evident on porous substrates and at eevated temperatures. Aow the system to cure for a minimum of 18 hours at 20 C, but no onger than 24 hours at 20 C before over-coating. If the over-coating time period is exceeded, the surface shoud be ighty abraded and vacuumed before further coats are appied. Ensure good air-fow and ventiation to assist with cure. High temperatures, strong drafts and substrate porosity can affect the apping time and can cause roer marks. Joints The spacing of movement joints must be determined by the design of the subfoor. A ive movement joints in the subfoor must be continued through the resin fooring. In a instances the type and positioning of movement joints shoud be agreed at the design stage between a parties concerned. Pease refer to Atro or FeRFA s Guide to the Specification and Appication of Synthetic Resin Systems for further guidance. Protection Whist of an extremey durabe nature, these foor systems must by thoroughy protected from the rigours and abuse that exist during the ongoing contractua works. The resin foor shoud reach fu chemica cure in 7 days at 20 C. Untreated fet paper wi suffice as protection from ight traffic, however if protection is required from other trades then the foowing protection option shoud be considered. Where heavier access is required then a more suitabe medium to take the oading, such as shuttering py or Correx by Cordek, shoud be paced on top of the untreated fet paper. The resin system shoud have cured for 48 hours prior to pacing the protection. No poyethyene sheets, inseed-treated hardboard, print or dyed card shoud be paced in contact with the resin surface. A joints in the protection medium shoud be taped, and a accidenta spiages shoud be recovered immediatey by remova and reinstatement of the protection. Damage wi occur to the system if the guidance is not foowed. Ceaning (during instaation) A toos and equipment shoud be reguary ceaned using Atro Sove EP to reduce buid up and maintain the quaity of the instaation. Avoid contamination of the resin surface with sovent as this may cause ocaised boom. Ensure that the correct PPE is worn at a times. Disposa Due diigence must be adopted if accidenta spiages occur. Recover using inert absorbent granues, transferring into a suitaby marked container. Disposa of a empty containers and accidenta spiages shoud be in accordance with the oca waste disposa authority. A joints shoud be fied with Atro Expand fexibe jointing compound. Pease see Atro Expand data sheet for further information.

5 Ceaning guidance Optimum sip resistance and appearance can ony be maintained with reguar ceaning. Foors with sip resistance wi require mechanica ceaning. Microfibre ceaning systems shoud be sufficient for routine maintenance of foors with a smooth surface, provided that a suitabe detergent/ dosage is used and the microfibre pads are changed with sufficient frequency to ensure their effectiveness. Steam ceaners and/or hot pressure ceaners shoud not be used on the foor or was. A cod / ambient pressure washer may be used if required, but the pressure shoud not exceed 1400psi. Warm water wi offer improved ceaning, but the water temperature shoud not exceed 60 C. Entrance matting wi reduce ceaning requirements and shoud aso enhance the ongevity of the foor, when combined with correct maintenance. Sweep or vacuum the foor to remove debris For norma ceaning, diute an akaine detergent such, as Atro Cean 44 or simiar, by 1:40 in cean water Aternativey, diute by 1:20 for infrequent heavy ceaning Liberay appy the water and detergent soution to the foor, scrubbing with a deck scrubber or sow-speed (< 400rpm) scrubbing machine and Atro UniPad or simiar Pay particuar attention to areas where residues may accumuate, such as interna corners of perimeter coves and around coumns etc If possibe, aow the detergent soution to remain on the foor for severa minutes to break down deposits, but not sufficienty ong to aow the soution to evaporate Remove the soution by wet vacuum recovery and foow this with a fresh water rinse, or rinse the soution into drains if permissibe It is important that a detergent residue is removed from the textured surface of the foor. Detergent may become sippery which affects safety, or sticky which attracts and hods more dirt Atro Cean 44 and Atro Unipads are avaiabe through the Resins Saes Desk. Pease obtain the correct materia safety data sheets from Atro prior to beginning your instaation. To order E-mai ResinSaesDesk@atro.com Ca Fax NOTE: Atro Ltd ( Atro ) endeavours to ensure that advice and information given in Product Data Sheets, Method Statements and Materia Safety Data Sheets (a known as Product Literature) is accurate and correct. However, where Atro has no contro over the seection of its products for particuar appications, it is important that any prospective customer, user or specifier, satisfies him / hersef that the product is suitabe for the intended appication. In this process, due regard shoud be taken of the nature and composition of the background / base and the ambient conditions both at the time of aying / appying / instaing / curing of the materia and when the competed work is to be brought into use. However, as site conditions and the execution of the work are beyond our contro, we accept no resutant iabiity. Atro s poicy is one of continuous research and deveopment and we reserve the right to update our products and information at any time without prior notice. If you d ike any more information or guidance pease get in touch, we re here to hep. te: fax: emai: enquiries@atro.com or expore