Certificate No: EWW812

Transcription

1 Certificate No: EWW812 i-sip Building System Description of Product This is an assessment of the Innovaré Systems Ltd Structural Insulated Panel System developed for wall and roofing. The assessment is for a typical four storey domestic property and external treatment should be dealt with separately. Photo/isometric drawing provided by manufacturer Key Factors Assessed Mechanical Resistance & Stability Safety in case of Fire Health, Hygiene and Environmental Safety in Use Protection against noise Energy Economy and heat retention Durability serviceability and identification Validity This certificate was first issued on 18 th September 2018 and is valid until 18 th September 2019 Issue Dated 18 th September 2018

2 The structurally insulated panels (SIPs) comprise OSB/3, EPS insulation and structural timber to form loadbearing walls and roofs in buildings. The panels have been verified as suitable as load bearing partitions and external walls for a typical four storey domestic property with a tiled duo-pitched roof and suitable wall cladding. The system can also be used in residential, commercial and institutional buildings both in loadbearing applications and as a non-loadbearing infill panel to a structural frame subject to the submission and verification of additional structural calculations on an individual project basis. i-sips are available in the following thicknesses: 111, 136, 162, 206 and 257mm. Maximum standard panel dimensions: 6.00 x 2.77 m. Design loadings have been taken to cover the building being located in any part of England or Wales with a maximum altitude of 100m and basic wind velocity of 25m/s. Roof construction consists of factory produced cassettes consisting of Engineered timber joists receiving particle board or plywood sheathing. Suspended floors consist of factory produced cassettes consisting of Engineered timber joists receiving particle board or plywood boarding. Wall construction consists of panels which have been checked with intermediate restraint (from an intermediate floor construction). Excluded from the check are the following items which should all be designed on a project specific basis: Drifted snow analysis Pitched roofs Ridge beams Purlins Eaves beams Flat roof cassettes Suspended floor cassettes Steelwork Lintels Balconies Staircases Foundations Overall resistance to uplift/overturning and the racking resistance of the structure

3 The Innovaré Systems Limited i-sip Structural Insulated Panel System relies on other construction products, materials and components to form a complete wall, floor and roof element. Structural design of the building /element incorporating the SIP shall be in accordance with the relevant Eurocode. Details of additional protection measures to resist moisture/contaminants from the ground and from moisture outside the building are site specific: to be determined by location, subsoil and exposure conditions. The installation must be undertaken by competent installers trained, registered and monitored by Innovaré Systems Limited and in strict accordance with their designs, details and specifications. The thermal insulation performance of this system should be considered in context of the contribution made to the overall performance of the wall structure. Appropriate thermal analysis will be provided in each instance to demonstrate continued compliance with Approved Document L The following items should be designed on a project specific basis: Ridge beams Purlins Eaves beams Steelwork Foundations Overall racking resistance of the structure First floor structure Notification that the structures have been completed and signed off by the manufacturer and are in accordance with the individual design. For LABC Warranty purposes: 1) The product is to be used and installed in strict accordance with the BBA certification. 2) The external cavity must be drained and ventilated, and the width must be in accordance with Chapter 7 of LABC Warranty s Technical Manual. 3) The SIP panels must be protected by a breather membrane within the cavity, 4) The system must be installed by trained operatives and to a height not exceeding 4 stories including a room in roof.

4 LABC consider that, the i-sip Building System will meet the functional requirements of the Building Regulations (listed below) if the criteria detailed in this certificate are met; The Building Regulations 2010 (as amended) England & Wales Regulation 7 AD A AD B AD L1 Materials and workmanship The system is acceptable. Structure Fire Safety Conservation of fuel and power The thermal insulation performance of this system should be considered in the context of the contribution made to the overall performance of the building. The Building Regulations 2010 (as amended) England AD B AD L1 Fire Safety Conservation of fuel and power The thermal insulation performance of this system should be considered in the context of the contribution made to the overall performance of the building. The Building Regulations 2010 (as amended) Wales AD B AD L1 Fire Safety Conservation of fuel and power The thermal insulation performance of this system should be considered in the context of the contribution made to the overall performance of the building. The Building (Scotland) Regulations 2004 (as amended) If you would like to discuss a specific use of the product in Scotland it will require an additional assessment under the Scottish Building Regulations and accordingly you should contact the LABSS STAS Administrator at

5 LABC Warranty LABC Warranty conditionally accepts the use of i-sip Building System, when installed and used in accordance with the Scope and Conditions of this Certificate. Visit for our LABC Warranty Technical Manual requirements and Warranty conditions of acceptance. ISO 9001:2015 Management Certificate BBA Certificate 08/SO40 BRE fire test report number & Thermal Performance U-Value Matrix RBA Acoustics Sound Insulation Test Report 3874/SIT2 ATTMA Air Permeability Test Certificate R DBM Consultants Design Calculations no. 8179

6 Innovaré Systems Limited Unit 3 Siskin Parkway West Middlemarch Business Park Coventry CV3 4PW Tel: enquiries@innovaresystems.co.uk Web: