SECURE LOCK INTERLOCKING TILES Product Guide Specification

Transcription

1 SECURE LOCK INTERLOCKING TILES Product Guide Specification PART 1 - GENERAL 1.1 SECTION INCLUDES A. Resilient, Interlocking, Playground safety surfacing tiles. 1.2 REFERENCES A. ASTM F a - Standard Specification for Impact Attenuation of Surface Systems Under and Around Playground Equipment. B. ASTM D 2859 Standard Test Method for Flammability of Finished Textile Floor Covering Materials as directed in Federal Document DOC FF C. ASTM C 1028 Standard Test Method for Determining the Static Coefficient of Friction of Ceramic Tile and Other Like Surfaces by the Horizontal Dynamometer Pull Meter Method. D. ASTM D 3676 Standard Specification for Rubber Cellular Cushion Used for Carpet or Rug Underlay. E. ASTM D 3389 Standard Test Method for Coated Fabrics Abrasion Resistance (Rotary Platform Double-Head Method). F. ASTM D 412 Standard Test Methods for Vulcanized Rubber and Thermoplastic Elastomers. G. ASTM D 624 Standard Test Method for Tear Strength of Conventional Vulcanized Rubber and Thermoplastic Elastomers. H. ASTM C 1026 Standard Test Method for Measuring the Resistance to Freeze-Thaw Cycling I. ASTM D 573 Standard Test Method for Rubber-Deterioration in an Air Oven (Heat Aged). J. ASTM E Standard Test Method for Critical Radiant Flux of Floor Covering Systems Using a Radiant Heat Energy Source. K. ASTM F Standard Specification for Determination of Accessibility of Surface Systems Under and Around Playground Equipment. 1

2 L. ASTM F Standard Test Methods for Comprehensive Characterization of Synthetic Turf Playing Surfaces and Materials: Suffix-DIN , Part 6: Water Permeability of Synthetic Turf Systems and Permeable Bases. 05/2018 M. ASTM D 395 Standard Test Methods for Rubber Property-Compression Set Method B: Compression Set Under Constant Deflection in Air. N. ASTM D 2240 Standard Test Method for Rubber Property-Durometer Hardness. O. ASTM C 501, 2009 Standard Test Method for Relative Resistance to Wear of Unglazed Ceramic Tile by the Taber Abraser. P. IPEMA Certified 1.3 SUBMITTALS A. Submittal Procedures. B. Product Data: Submit manufacturer's product data, including installation and/or subsurface recommendations. C. Samples: Submit manufacturer's sample of 1 full tile. D. Test Reports: Submit certified test reports from qualified independent testing agency indication results of the following tests: 1. Impact Attenuation: ASTM F a. 2. Freeze Thaw: ASTM C Rubber Deterioration/ Air oven: ASTM D Compression Set: ASTM D Tensile Strength: ASTM D Elongation at Break: ASTM D Tear Strength: ASTM D Wear Coarse Density (durability). 9. Durometer Hardness: ASTM D Taber Abrasion: ASTM C Flammability: ASTM D Static Coefficient of Friction: ASTM C E. Certificate of Compliance: Submit manufacturer s certificate of compliance indicating materials comply with specified requirements. 2

3 F. Maintenance Instructions: Submit manufacturer s maintenance and cleaning instructions. G. Warranty: Submit Manufacturer s standard warranty. 1.4 QUALITY ASSURANCE A. Installer's Qualifications: 1. Installers must have successful experience in installation of playground safety surfacing tiles of similar type to that specified, with a minimum of 20 projects completed within last 5 years. 2. Employ persons trained for installation of playground safety surfacing tiles and are approved by manufacturer 1.5 DELIVERY, STORAGE, AND HANDLING A. Delivery: Deliver materials to site in manufacturer's original, unopened containers and packaging, with labels clearly identifying product name and manufacturer. B. Storage: 1. Store materials in accordance with manufacturer s instructions. 2. Playground Safety Surfacing Tiles: a. Store tiles in a dry area prior to installation. b. Protect tiles from direct sunlight before installation. 3. Adhesive: Store adhesive in a dry area at a minimum temperature of 40 degrees F. C. Handling: Protect materials during handling and installation to prevent damage. 1.6 ENVIRONMENTAL REQUIREMENTS A. Air Temperature: The air temperature should be a minimum of 40 degrees F (4 degrees C) and preferably climbing for a minimum of 24 hours before and during installation. B. Tile Temperature: Ensure surface temperature of playground safety surfacing tiles is a minimum of 50 degrees F (10 degrees C) at the time of installation. C. Tile or Air Temperatures: Consult manufacturer s installation instructions for modified installation procedure when tile or air temperatures are above 85 degrees F (29 degrees C). 3

4 1.7 WARRANTY A. Materials and Workmanship: Playground safety surfacing tiles shall be warranted for defects in materials and workmanship for 10 years from date of Final Acceptance (i.e. Notice of Completion). PART 2: PRODUCTS 2.1 MANUFACTURER RUBBER DESIGNS LLC Skyway Circle Melbourne, FL Toll Free : PLAYGROUND SURFACING TILES A. Tiles: SECURE LOCK INTERLOCKING TILE. 1. Series: Interlocking Tile 2. Description: Resilient, interlocking, playground safety surfacing tiles. 3. Compliance: Meet and exceed CSPC guidelines for impact attenuation. 4. Material: Compression-molded, recycled rubber and binding agents. 5. Tile Locking: U-shaped male and female configuration running full length on all 4 sides to lock tiles to adjacent tiles. 6. Top Edges: Chamfered. 7. Tile Bottom: Hollow core Tunnel Shaped Grid pattern. 8. Wear Layer: A. Standard Series: Rubber Buffings: 10 Mesh. Minimum.50 inch thick. B. Premium Series: EPDM Granules:.5-1.5mm. Minimum.50 inch thick. 9. Size: X Nominal. Installed size: 24 X Thickness: 4

5 A. Critical Fall Height 4 Feet: 2.25 inches B. Critical Fall Height 6 Feet: 2.75 inches C. Critical Fall Height 8 Feet: 3.25 inches D. Critical Fall Height 10 Feet: 4.25 inches 05/ Minimum Weight Each Tile: A Inch Thickness: 24.5 pounds. B Inch Thickness: 27.5 pounds. C Inch Thickness: 30.5 pounds. D Inch Thickness: 38.5 pounds. 12. Colors: 1. Standard Series: [Black] [Green] [Red] [Blue] [Tan] [Brown] [Grey] 1) Percent Color: [100 percent color]. 2. Premium Series: EPDM Granules 1) Percent Color: [Up to 90 percent color, 10 percent black]. B. Testing Results: 1. Impact Attenuation, ASTM F a: 1) 2.25-inch Thickness: a. G-max Score: Less than 100. b. Head Injury Criteria (HIC) Score: Less than ) 2.75-inch Thickness: a. G-max Score: Less than 140. b. Head Injury Criteria (HIC) Score: Less than ) 3.25-inch Thickness: a. G-max Score: Less than 138. b. Head Injury Criteria (HIC) Score: Less than ) 4.25-inch Thickness: a. G-max Score: Less than 115. b. Head Injury Criteria (HIC) Score: Less than

6 2. Freeze Thaw, ASTM C 1026: no appearance of the presence of cracking, chipping, or breaking of the tile. 05/ Rubber Deterioration/Air Oven, ASTM D 573: No deterioration. 4. Compression Set, ASTM D 395: 2.29 percent Compression Set. 5. Tensile Strength, ASTM D 412: psi. 6. Elongation at Break, ASTM D 412: percent. 7. Tear Strength, D 624: lbs./force/inch. 8. Flammability: a. Burning Pill, ASTM D 2859: Pass. b. Critical Radiant Flux, ASTM E 648: No Classification. 9. Determination of Accessibility, ASTM F 1951: Meets/Exceeds requirements. 10. Water Permeability, ASTM F 1551: 43.8 inches/hour. 11. Durometer Hardness, ASTM D 2240: Static Coefficient of friction, ASTM C 1028: a. Dry:.63 b. Wet: Taber Abrasion, Wear index, ASTM C 501: ACCESSORIES A. Corners: 1. Prefabricated outside and inside corners. 2. Material: Same as playground safety surfacing tiles. B. Ramps: 1. Prefabricated Ramps: 2. Prefabricated ADA-Compliant Ramps: 3. Material: Same as playground safety surfacing tiles. C. Edging: 6

7 1. Prefabricated Curb Edging: 2. Material: Same as playground safety surfacing tiles. D. Adhesive: Furnished by manufacturer. PART 3: EXECUTION 3.1 EXAMINATION A. Examine areas to receive playground safety surfacing tiles. Notify responsible parties if areas are not acceptable. Do not begin installation until unacceptable conditions have been corrected. 3.2 PREPARATION A. Prepare subsurface in accordance with manufacturer's instructions to ensure proper slope, support and drainage for playground safety surfacing tiles. Notes: Specify subsurface of concrete, or asphalt. It is critical that a proper subsurface drainage system be constructed or the tile surface may not stay level and may cause damage to the surfacing. C. Concrete Subsurface: 1. Concrete subsurface shall be as specified. 2. Apply light broom finish. 3. Ensure concrete is sound with no loose material. 4. Ensure concrete is a minimum of 28 days old. 5. Power wash existing concrete in accordance with manufacturer's instructions. D. Asphalt Subsurface: 1. Asphalt subsurface shall be as specified. 2. Ensure asphalt is sound with no loose material or cracks. 3. Ensure asphalt is a minimum of 28 days old. 4. Power Wash existing asphalt. 3.3 INSTALLATION A. Install Secure Lock Interlocking tiles in accordance with manufacturer's instructions at locations indicated. 7

8 B. Ensure prepared subsurface and tiles are dry and clean. 05/2018 C. Layout tile surface in accordance with manufacturer's instructions. D. Install tiles in single installation session, if possible. E. Apply adhesive in accordance with manufacturer's instructions for tile-to-tile as well as tile-to-base for all keystone and strategic tile rows. 3.4 CLEANING A. Remove adhesive spills from playground safety surfacing tiles and equipment in accordance with manufacturer s instructions. B. Clean tiles in accordance with manufacturer's instructions. 3.5 PROTECTION A. Protect playground safety surface tiles from foot traffic for a minimum of 12 hours after installation. B. Protect completed tiles from damage during construction. END OF SECTION 8

9 Secure Lock Ten Year Interlocking Tile Warranty SUBJECT TO THE FOLLOWING TERMS AND CONDITIONS, SECURE LOCK (MANUFACTURER) WARRANTS TO THE BUYER THAT THE SECURE LOCK INTERLOCKING TILE SOLD TO THE BUYER WILL BE FREE FROM MANUFACTURING DEFECTS AT THE DELIVERY. IF UPON INSPECTION BY THE PURCHASER UPON RECEIPT, THE SECURE LOCK INTERLOCKING TILE EVIDENCES MANUFACTURING DEFECTS, MANUFACTURER S LIABILITY AND BUYER S REMEDIES ARE LIMITED, AT MANUFACTURER S OPTION, TO REPLACE THE DEFECTIVE SECURE LOCK INTERLOCKING TILE STARTING FROM THE DATE INVOICED BY MANUFACTURER. MANUFACTURER FURTHERMORE WARRANTS THAT THE SECURE LOCK INTERLOCKING TILE WILL NOT PREMATURELY DECOMPOSE BECAUSE OF WEATHERING FOR A PERIOD OF TEN (10) YEARS FROM THE DATE INVOICED BY MANUFACTURER, IF PROPERLY INSTALLED, CLEANED, MAINTAINED, AND USED FOR THE PURPOSE FOR WHICH THE MANUFACTURER INTENDED. BUYER SHALL GIVE MANUFACTURER NOTICE OF CLAIM UNDER THIS WARRANTY WITHIN THIRTY (30) DAYS OF DISCOVERING PREMATURE DETERIORATION OF THE INTERLOCKING TILE. IF UPON INSPECTION BY THE MANUFACTURER, THE INTERLOCKING TILE SHOWS PREMATURE DETERIORATION BECAUSE OF WEATHERING WITHIN THE TEN (10) YEAR PERIOD STATED HEREIN, THE MANUFACTURER S LIABILITY AND THE BUYER S REMEDIES ARE LIMITED AT THE MANUFACTURER S OPTION TO PROVIDE REPLACEMENT OR REPAIR OF MATERIALS FOR THE INTERLOCKING TILE. THE WARRANTY WILL BE FOR 100% OF THE PRICE OF THE JOB FOR ONE (1) YEAR AFTER SUBSTANTIAL COMPLETION. THEREAFTER, THE WARRANTY COVERS 90% OF THE SUGGESTED RETAIL PRICE FOR THE CURRENT YEAR OF THE JOB FROM THE FIRST ANNIVERSARY OF SUBSTANTIAL COMPLETION UNTIL THE SECOND ANNIVERSARY OF SUBSTANTIAL COMPLETION. THEREAFTER, THE WARRANTY COVERS 80% OF THE SUGGESTED RETAIL PRICE FOR THE CURRENT YEAR OF THE JOB FROM THE SECOND ANNIVERSARY OF SUBSTANTIAL COMPLETION UNTIL THE THIRD ANNIVERSARY OF SUBSTANTIAL COMPLETION. THEREAFTER, THE WARRANTY COVERS 70% OF THE SUGGESTED RETAIL PRICE FOR THE CURRENT YEAR OF THE JOB FROM THE THIRD ANNIVERSARY OF SUBSTANTIAL COMPLETION UNTIL THE FOURTH ANNIVERSARY OF SUBSTANTIAL COMPLETION. THEREAFTER, THE WARRANTY COVERS 60% OF THE SUGGESTED RETAIL PRICE FOR THE CURRENT YEAR OF THE JOB FROM THE FOURTH ANNIVERSARY OF SUBSTANTIAL COMPLETION UNTIL THE FIFTH ANNIVERSARY OF SUBSTANTIAL COMPLETION. THEREAFTER, THE WARRANTY COVERS 50% OF THE 9

10 SUGGESTED RETAIL PRICE FOR THE CURRENT YEAR OF THE JOB FROM THE FIFTH ANNIVERSARY OF SUBSTANTIAL COMPLETION UNTIL THE SIXTH ANNIVERSARY OF SUBSTANTIAL COMPLETION. THEREAFTER, THE WARRANTY COVERS 40% OF THE SUGGESTED RETAIL PRICE FOR THE CURRENT YEAR OF THE JOB FROM THE SIXTH ANNIVERSARY OF SUBSTANTIAL COMPLETION UNTIL THE SEVENTH ANNIVERSARY OF SUBSTANTIAL COMPLETION. THEREAFTER, THE WARRANTY COVERS 30% OF THE SUGGESTED RETAIL PRICE FOR THE CURRENT YEAR OF THE JOB FROM THE SEVENTH ANNIVERSARY OF SUBSTANTIAL COMPLETION UNTIL THE EIGHTH ANNIVERSARY OF SUBSTANTIAL COMPLETION. THEREAFTER, THE WARRANTY COVERS 20% OF THE SUGGESTED RETAIL PRICE FOR THE CURRENT YEAR OF THE JOB FROM THE EIGHTH ANNIVERSARY OF SUBSTANTIAL COMPLETION UNTIL THE NINETH ANNIVERSARY OF SUBSTANTIAL COMPLETION. THEREAFTER, THE WARRANTY COVERS 10% OF THE SUGGESTED RETAIL PRICE FOR THE CURRENT YEAR OF THE JOB FROM THE NINETH ANNIVERSARY OF SUBSTANTIAL COMPLETION UNTIL THE TENTH ANNIVERSARY OF SUBSTANTIAL COMPLETION. THIS WARRANTY EXCLUDES ACTS OF GOD, DAMAGE FROM IMPROPER MAINTENANCE, DAMAGE CAUSED DURING FREIGHT DELIVERY, NORMAL WEAR AND TEAR, PRODUCT VANDALISM BY WAY OF MARKING, SCARRING, PUNCTURING EXPERIENCED FROM ITEMS SUCH AS PENS, PENCILS, KNIVES, HIGH HEELS OR ANY SUCH OBJECT OF LIKENESS, OR MACHINERTY NOT INTENDED FOR TRAFFICKING ON SURFACE OR USE OF MAINTENANCE EQUIPMENT WHEREIN THE SURFACING SUPPORTS THE WEIGHT OF THE EQUIPMENT, DAMAGED DIRECTLY OR INDIRECTLY, INCLUDING, BUT NOT LIMITED TO ON ACCOUNT OF ACCIDENT VANDALISM, ANIMALS, FIRE, FLOOD, CHEMICAL REACTION, STATIC, IMPROPER SUBSURFACE PREPARATION, FAILURE OF THE SUBSURFACE AFTER INSTALLATION AND THE USE OF CLEANING FLUIDS, OR IMPROPER CLEANING METHODS (REFER TO CLEANING MAINTENANCE INSTRUCTIONS FOR DETAILS OF PROPER CLEANING METHODS), AND NATURAL WEAKENING OF PIGMENTS DUE TO PROLONGED SUNGLIGHT PENETRATION AND ULTRAVIOLET RAY EXPOSURE FROM DIRECT OR GLASS- FILTERED SUNLIGHT. THIS WARRANTY ONLY APPLIES TO NEW PRODUCTS PURCHASED, AND IS LIMITED TO THE REPAIR OR REPLACEMENT OF SECURE LOCK PRODUCTS. THIS WARRANTY DOES NOT COVER THE SHIPPING COSTS FOR RETURN, INCONVENIENCE OR CONSEQUENTIAL DAMAGES. NO REPRESENTATIVE OF THE MANUFACTURER HAS AUTHORITY TO MAKE ANY REPRESENTATIONS OR PROMISES EXCEPT STATED HEREIN. NO ALTERATIONS TO PRODUCT SURFACE BY ANYONE OTHER THAN AN AUTHORIZED SECURE LOCK APPLICATOR SHALL TERMINATE CUSTOMER WARRANTY. SECURE LOCK IS NOT RESPONSIBLE FOR SITE SECURITY DURING AND 10

11 AFTER THE PRODUCT INSTALLATION. CUSTOMER MUST RECEIVE A COPY OF PRODUCT WARRANTY FROM AN AUTHORIZED SECURE LOCK DEALER. WHEREBY SUBMITTING A SIGNED COPY OF THE WARRANTY, ALONG WITH THE PURCHASE ORDERS TO THE DEALER DISTRIBUTOR, A SIGNED COPY OF THE WARRANTY MUST BE MAINTAINED BY THE CUSTOMER OR DEALER DISTRIBUTOR FOR THE WARRANTY TO BE HONORED. THE PRODUCT WARRANTY IS COMPLETELY REPRESENTED HERE IN WRITING, AS ALL PROMISES ARE DECLARED WITHIN THIS DOCUMENT. THE MANUFACTURER SHALL NOT BE LIABLE FOR ANY INCIDENTAL, OR CONSEQUENTIAL DAMAGES TO THE PRODUCT, OR ANY TO THE SURROUNDING PREMISES ARISING UNDER ANY THEORY OF LAW WHATSOEVER. Customer/Project Name: Authorized Signature: Date: Title: Date of Invoice: 11

12 SECURE LOCK 12

13 SECURE LOCK 13