CREEK Technical Services, LLC

Transcription

1 a CREEK Certificate of Authorization Edinburgh Dr Tampa, FL (813) EVALUATION REPORT FLORIDA BUILDING CODE, 6 TH EDITION (2017) Manufacturer: FIRESTONE BUILDING PRODUCTS CO., LLC Issued April 18, th Avenue South Nashville, TN (800) Manufacturing Plants: Quality Assurance: Indianapolis, IN UL LLC (QUA9625) SCOPE Category: Roofing Subcategory: Single Ply Roof Code Sections: , , , , , , , , , , , Properties: Wind Resistance, Physical Properties, Impact Resistance PRODUCT DESCRIPTION Products Specification Description Firestone UltraPly TPO XR 100 ASTM D 6878 TAS mil thick thermoplastic polyolefin, heat-weldable, single-ply roof membrane with polyester weft-inserted reinforcement and 8 oz. non-woven polyester fabric backing Firestone UltraPly TPO XR 115 ASTM D 6878 TAS 131 Firestone UltraPly TPO XR 135 ASTM D 6878 TAS mil thick thermoplastic polyolefin, heat-weldable, single-ply roof membrane with polyester weft-inserted reinforcement and 8 oz. non-woven polyester fabric backing 80-mil thick thermoplastic polyolefin, heat-weldable, single ply roof membrane with polyester weft-inserted reinforcement and 8 oz. polyester fleece backing FBP FL# R2 Page 1 of 5 This evaluation report is provided for State of Florida product approval under Rule 61G20-3. The manufacturer shall notify CREEK of any product changes or quality assurance changes throughout the duration for which this report is valid. This evaluation report does not express nor imply warranty, installation, recommended use, or other product attributes that are not specifically addressed herein.

2 A CREEK UltraPly TPO XR with SBS Modified Roofing s REFERENCES Entity Report Standards FM Approvals (TST1867) FM 4470 (2012) FM Approvals (TST1867) FM 4470 (2012); FM 4474 (2011) FM Approvals (TST1867) FM 4470 (2012) FM Approvals (TST1867) FM 4474 (2011) FM Approvals (TST1867) FM 4470 (2012); FM 4474 (2011) FM Approvals (TST1867) FM 4470 (1992) FM Approvals (TST1867) FM 4470 (2012); FM 4474 (2011) FM Approvals (TST1867) FM 4470 (2012); FM 4474 (2011) FM Approvals (TST1867) FM 4470 (2012) FM Approvals (TST1867) FM 4470 (2012) FM Approvals (TST1867) FM 4470 (2012) FM Approvals (TST1867) FM 4470 (2012) FM Approvals (TST1867) FM 4470 (2012) FM Approvals (TST1867) FM 4470 (2012) FM Approvals (TST1867) RR FM 4470 (2012) PRI Construction Materials Technologies (TST5878) FBP ASTM D 6164 (2011) PRI Construction Materials Technologies (TST5878) FBP ASTM D 6164 (2011) PRI Construction Materials Technologies (TST5878) FBP TAS 114(J & H) (1995);TAS 117(B) (1995) PRI Construction Materials Technologies (TST5878) FBP FM 4474(D) (2011); TAS 114(J) (1995) PRI Construction Materials Technologies (TST5878) FBP ASTM D 6163 [2000(2008)] PRI Construction Materials Technologies (TST5878) FBP FM 4474(B) (2011); TAS 114(D) (1995) PRI Construction Materials Technologies (TST5878) FBP ASTM D 4601 [2004(2012)E1] PRI Construction Materials Technologies (TST5878) FBP ASTM D 1876 (2008); ASTM D 903 [1998(2010];; TAS 117(B) (1995); TAS 114(D & H) (1995) PRI Construction Materials Technologies (TST5878) FBP FM 4474(D) (2011); TAS 114(J) (1995) PRI Construction Materials Technologies (TST5878) FBP FM 4474(D) (2011); TAS 114(J) (1995) PRI Construction Materials Technologies (TST5878) FBP FM 4474(B) (2011); TAS 114(D) (1995) PRI Construction Materials Technologies (TST5878) FBP ASTM D 6878 (2011a); TAS 131 (1995) PRI Construction Materials Technologies (TST5878) FBP FM 4474(D) (2011); TAS 114(J) (1995) PRI Construction Materials Technologies (TST5878) FBP FM 4474(D) (2011); TAS 114(J) (1995) PRI Construction Materials Technologies (TST5878) FBP FM 4474(D) (2011); TAS 114(J) (1995) PRI Construction Materials Technologies (TST5878) FBP FM 4474(D) (2011); TAS 114(J) (1995) PRI Construction Materials Technologies (TST5878) FBP FM 4474(D) (2011); TAS 114(J) (1995) PRI Construction Materials Technologies (TST5878) FBP FM 4474(C) (2011) PRI Construction Materials Technologies (TST5878) FBP FM 4474(C) (2011) PRI Construction Materials Technologies (TST5878) FBP FM 4474(D) (2011); TAS 114(J) (1995) PRI Construction Materials Technologies (TST5878) FBP FM 4474(D) (2011); TAS 114(J) (1995) PRI Construction Materials Technologies (TST5878) FBP FM 4474(D) (2011); TAS 114(J) (1995) PRI Construction Materials Technologies (TST5878) FBP FM 4474(D) (2011); TAS 114(J) (1995) PRI Construction Materials Technologies (TST5878) FBP FM 4474(D) (2011); TAS 114(J) (1995) PRI Construction Materials Technologies (TST5878) FBP ASTM D 6163 [2000(2008)] PRI Construction Materials Technologies (TST5878) FBP ASTM D 6164 (2011) PRI Construction Materials Technologies (TST5878) FBP FM 4474(B) (2011); TAS 114(D) (1995) PRI Construction Materials Technologies (TST5878) FBP FM 4474(B) (2011); TAS 114(D) (1995) PRI Construction Materials Technologies (TST5878) FBP FM 4474(D) (2011); TAS 114(J) (1995) PRI Construction Materials Technologies (TST5878) FBP FM 4474(D) (2011); TAS 114(J) (1995) PRI Construction Materials Technologies (TST5878) FBP FM 4474(D) (2011); TAS 114(J) (1995) PRI Construction Materials Technologies (TST5878) FBP FM 4474(D) (2011); TAS 114(J) (1995) PRI Construction Materials Technologies (TST5878) FBP FM 4474(D) (2011); TAS 114(J) (1995) PRI Construction Materials Technologies (TST5878) FBP FM 4474(D) (2011); TAS 114(J) (1995) PRI Construction Materials Technologies (TST5878) FBP ASTM D 6878 (2011a); TAS 131 (1995) PRI Construction Materials Technologies (TST5878) FBP FM 4474(D) (2011); TAS 114(J) (1995) PRI Construction Materials Technologies (TST5878) FBP FM 4474(D) (2011); TAS 114(J) (1995) PRI Construction Materials Technologies (TST5878) FBP FM 4474(C) (2011) PRI Construction Materials Technologies (TST5878) FBP FM 4474(D) (2011); TAS 114(J) (1995) PRI Construction Materials Technologies (TST5878) FBP FM 4470 (2012) PRI Construction Materials Technologies (TST5878) FBP ASTM D 1970 (2015a) PRI Construction Materials Technologies (TST5878) FBP ASTM D 6163 [2000(2008)] PRI Construction Materials Technologies (TST5878) FBP ASTM D 6164 (2011) PRI Construction Materials Technologies (TST5878) FBP ASTM D 4601 [2004(2012)E1] PRI Construction Materials Technologies (TST5878) FBP B FM 4474(D) (2011); TAS 114(J) (1995) PRI Construction Materials Technologies (TST5878) FBP UL 1897 (2012) PRI Construction Materials Technologies (TST5878) FBP B FM 4474(D) (2011); TAS 114(J) (1995) PRI Construction Materials Technologies (TST5878) FBP FM 4474(D) (2011); TAS 114(J) (1995); FBP FL# R2 Page 2 of 5 This evaluation report is provided for State of Florida product approval under Rule 61G20-3. The manufacturer shall notify CREEK of any product changes or quality assurance changes throughout the duration for which this report is valid. This evaluation report does not express nor imply warranty, installation, recommended use, or other product attributes that are not specifically addressed herein.

3 A CREEK UltraPly TPO XR with SBS Modified Roofing s Entity Report Standards UL1897 (2012) PRI Construction Materials Technologies (TST5878) FBP FM 4474(D) (2011); TAS 114(J) (1995); UL1897 (2012) PRI Construction Materials Technologies (TST5878) FBP FM 4474(D) (2011); TAS 114(J) (1995); UL1897 (2012) PRI Construction Materials Technologies (TST5878) FBP FM 4474(D) (2011); TAS 114(J) (1995); UL1897 (2012) PRI Construction Materials Technologies (TST5878) FBP FM 4474(B) (2011); TAS 114(D) (1995) PRI Construction Materials Technologies (TST5878) FBP A FM 4474(D) (2011); TAS 114(J) (1995); UL1897 (2012) PRI Construction Materials Technologies (TST5878) FBP ASTM D 3746 [1985(2015)] PRI Construction Materials Technologies (TST5878) FBP A FM 4474(D) (2011); TAS 114(J) (1995); UL1897 (2012) PRI Construction Materials Technologies (TST5878) FBP FM 4474(D) (2011); TAS 114(J) (1995); UL1897 (2012) PRI Construction Materials Technologies (TST5878) FBP FM 4474(B) (2011); TAS 114(D) (1995); PRI Construction Materials Technologies (TST5878) FBP FM 4474(D) (2011); TAS 114(J) (1995) UL 1897 (2012) PRI Construction Materials Technologies (TST5878) FBP FM 4474(D) (2011); TAS 114(J) (1995) UL 1897 (2012) PRI Construction Materials Technologies (TST5878) FBP ASTM D 6164 (2011) PRI Construction Materials Technologies (TST5878) FBP FM 4474(D) (2011); TAS 114(J) (1995) UL 1897 (2012) PRI Construction Materials Technologies (TST5878) FBP A FM 4474(D) (2011); TAS 114(J) (1995) UL 1897 (2012) PRI Construction Materials Technologies (TST5878) FBP FM 4474(D) (2011); TAS 114(J) (1995); UL1897 (2012) PRI Construction Materials Technologies (TST5878) FBP ASTM D 4601 [2004(2012)E1] PRI Construction Materials Technologies (TST5878) FBP FM 4474(B) (2011); TAS 114(D) (1995) PRI Construction Materials Technologies (TST5878) FBP ASTM D 6164 (2011) PRI Construction Materials Technologies (TST5878) FBP FM 4474(D) (2011); TAS 114(J) (1995); UL1897 (2012) PRI Construction Materials Technologies (TST5878) FBP FM 4474(D) (2011); TAS 114(J) (1995); UL1897 (2012) PRI Construction Materials Technologies (TST5878) FBP FM 4474(D) (2011); TAS 114(J) (1995); UL1897 (2012) PRI Construction Materials Technologies (TST5878) FBP FM 4474(C) (2011) PRI Construction Materials Technologies (TST5878) FBP FM 4474(D) (2011); TAS 114(J) (1995); UL 1897 (2012) PRI Construction Materials Technologies (TST5878) MSA ASTM D 4897 [2001(2009)] Trinity ERD (TST6049) F ASTM D 6163 [2000(2008)] FBP FL# R2 Page 3 of 5 This evaluation report is provided for State of Florida product approval under Rule 61G20-3. The manufacturer shall notify CREEK of any product changes or quality assurance changes throughout the duration for which this report is valid. This evaluation report does not express nor imply warranty, installation, recommended use, or other product attributes that are not specifically addressed herein.

4 A CREEK UltraPly TPO XR with SBS Modified Roofing s LIMITATIONS 1. Fire classification is not within the scope of this evaluation. 2. The roof deck and the roof deck attachment shall be designed by others to meet the minimum design loads established for components and cladding and in accordance with FBC requirements. 3. Foam plastic insulation shall be installed in accordance with the FBC Section and In the HVHZ, fastener spacing for insulation attachment is determined using a Minimum Characteristic Force (F ) of 275 lbf as demonstrated via testing to TAS 105. If the field tested fastener value is below 275 lbf, then insulation attachment shall not be acceptable. 5. In the HVHZ, fastener spacing for base sheets or membrane attachment shall meet the minimum fastener resistance value and the for the specified assembly. It is permissible for a qualified professional to submit a revised fastener spacing utilizing the withdrawal resistance value obtained from TAS 105 testing and calculations performed in accordance with RAS 117 and/or RAS 137, when the fastener resistance is found less than required. 6. In the HVHZ, if mechanical attachment through the lightweight insulating concrete to the structural deck is proposed, a field fastener withdrawal test shall be conducted in compliance with TAS 105 to determine equivalent or increased attachment densities. Revised fastener densities shall be submitted utilizing the withdrawal resistance value obtained from TAS 105 testing and calculations performed in accordance with RAS 117 and/or RAS For assemblies containing mechanical attachment, the allowable uplift pressure for the selected assembly shall meet or exceed the minimum design loads as determined in accordance with the FBC Chapter 16. For perimeter and corner roof zones 2 and 3, the attachment density may be increased by a qualified design professional, as necessary, to meet the design pressure requirements in these areas. In the HVHZ, calculations shall be conducted in compliance with RAS 117 and/or RAS 137. Outside the HVHZ, commonly used standards include RAS 117, FM LPDS 1-29, or ANSI/SPRI WD Reroofing applications shall be examined in accordance with FBC Section 1511 outside of the HVHZ and FBC Section 1521 within the HVHZ. For mechanically fastened systems, a field withdrawal resistance test (TAS 105 in the HVHZ; ANSI/SPRI FX-1 or TAS 105 in the non- shall be conducted by a qualified professional to ensure the fastener meets the minimum design load requirements of the system. For adhered systems, a field uplift resistance test (TAS 124 in the HVHZ; ASTM E 907, FM LPDS 1-52, ANSI/SPRI IA-1, or TAS 124 in the non- shall be conducted to confirm conformance of the existing to the minimum design loads. 9. For assemblies containing fully adhered or ribbon adhered attachment, or where extrapolation of the assembly is not permitted, the for the selected assembly shall meet or exceed the minimum design loads as determined in accordance with the FBC Chapter 16 without augmentation. 10. Installation of the evaluated products shall comply with this report, the FBC, and the manufacturer s published application instructions. Where discrepancies exist between these sources, the more restrictive and FBC compliant installation detail shall prevail. 11. The minimum roof slope shall be 1/4:12 for new construction. 12. All products listed in this report shall be manufactured under a quality assurance program in compliance with Rule 61G20-3. FBP FL# R2 Page 4 of 5 This evaluation report is provided for State of Florida product approval under Rule 61G20-3. The manufacturer shall notify CREEK of any product changes or quality assurance changes throughout the duration for which this report is valid. This evaluation report does not express nor imply warranty, installation, recommended use, or other product attributes that are not specifically addressed herein.

5 A CREEK UltraPly TPO XR with SBS Modified Roofing s COMPLIANCE STATEMENT The products evaluated herein by Zachary R. Priest, P.E. have demonstrated compliance with the Florida Building Code, 6 th Edition (2017) as evidenced in the referenced documents submitted by the named manufacturer. Zachary R. Priest, P.E. Florida Registration Organization ANE9641 CERTIFICATION OF INDEPENDENCE CREEK does not have, nor will it acquire, a financial interest in any company manufacturing or distributing products under this evaluation. CREEK is not owned, operated, or controlled by any company manufacturing or distributing products under this evaluation. Zachary R. Priest, P.E. does not have, nor will acquire, a financial interest in any company manufacturing or distributing products under this evaluation. Zachary R. Priest, P.E. does not have, nor will acquire, a financial interest in any other entity involved in the approval process of the product. APPENDICES 1) APPENDIX A Installation (6 pages) 2) Nomenclature and Approved Assemblies (28 pages) FBP FL# R2 Page 5 of 5 This evaluation report is provided for State of Florida product approval under Rule 61G20-3. The manufacturer shall notify CREEK of any product changes or quality assurance changes throughout the duration for which this report is valid. This evaluation report does not express nor imply warranty, installation, recommended use, or other product attributes that are not specifically addressed herein.

6 [NOMENCLATURE] UltraPly TPO XR with SBS Modified Roofing s APPENDIX A INSTALLATION Note - Refer to the APPROVED ASSEMBLIES section of this report within Appendix B for specific installation details of a selected assembly. Unless otherwise specified in this report the following installation details shall be met for the named products: Component Product Installation Detail Fastening s Insulation Adhesives Membrane Adhesives Insulation/Cover Boards Base/Ply Sheets Firestone All-Purpose Fasteners Firestone All-Purpose S Fasteners Firestone Concrete Drive Firestone 1.7 LWC Base-Ply Fastener Firestone Heavy Duty Fasteners Firestone Insulation Fastening Plates Firestone Metal Batten Strip Min.0.75-inch penetration through the top rib of the steel deck or wood deck Min embedment into min. 3 thick structural concrete Full embedment of shank into substrate Min. 7-inch penetration through the top rib of the steel deck or wood deck. Min. penetration 1-inch into concrete deck. Min. 3-inch diameter Galvalume steel plate Min. 1-inch wide, in. Galvalume steel batten ASTM D 312, Type IV Asphalt Fully adhered within the EVT range at a rate of lbs/100 ft 2 Firestone I.S.O. Fix II Firestone I.S.O. Stick Firestone I.S.O. Twin Pack Firestone I.S.O. Spray R Firestone Twin Jet Partially adhered in 0.75 to 1-inch wide ribbons Partially adhered in 0.75 to 1-inch wide ribbons Partially adhered in 0.5 to 0.75-inch wide ribbons Partially adhered in 0.75 to 1-inch wide ribbons Partially adhered in 1 to 1.25-inch wide ribbons ASTM D 312, Type IV Asphalt Fully adhered within the EVT range at a rate of lbs/100 ft 2 Firestone I.S.O. Spray R Firestone XR Stick Partially adhered in inch wide ribbons Partially adhered in inch wide ribbons Owens Corning PermaMop Asphalt Fully adhered within the EVT range at a rate of lbs/100 ft 2 Georgia-Pacific DensDeck Georgia-Pacific Firestone ISO 95+ GL GenFlex ISO Insulation Firestone ISO 95+ GL (Tapered) GenFlex ISO Insulation (Tapered) Firestone ISOGARD HD GenFlex HD ISO Firestone ISOGARD HD Composite GenFlex HD Composite ISO Firestone RESISTA GenFlex Coated Glass Facer Structodek High Density Fiberboard USG Gypsum-Fiber Roof Board USG Glass-Mat Roof Board SA Channel Venting Base SBS Base SBS Glass Torch Base SBS Glass Torch Base 1.5 SBS Poly Base SBS Poly Torch Base Min inch thick thick; Min. 20 psi; Adhered boards shall be a maximum 4 ft x 4 ft 0.5-inch to start with 0.25-inch per ft taper; Adhered boards shall be a maximum 4 ft x 4 ft thick; Adhered boards shall be a maximum 4 ft x 4 ft thick; Adhered boards shall be a maximum 4 ft x 4 ft thick; Min. 20 psi; Adhered boards shall be a maximum 4 ft x 4 ft thick Min inch thick Min. 3.4-inch wide side-laps; Min. 6-inch end laps; Side-laps shall be installed perpendicular to the direction of the steel deck ribs and parallel to the direction of the wood trusses for mechanically attached systems FBP FL# R2 Page 1 of 6 This evaluation report is provided for State of Florida product approval under Rule 61G20-3. The manufacturer shall notify CREEK of any product changes or quality assurance changes throughout the duration for which this report is valid. This evaluation report does not express nor imply warranty, installation, recommended use, or other product attributes that are not specifically addressed herein.

7 [NOMENCLATURE] Component Product Installation Detail Base/Ply Sheets (Cont d) Membrane Vapor Barriers Cellular Lightweight Concrete SBS Premium Base SBS Premium Poly Base SBS Smooth MB Base UltraPly TPO XR 100 UltraPly TPO XR 115 UltraPly TPO XR 135 Firestone V-Force Vapor Barrier Membrane Min. 300 psi Celcore S-1 Min. 300 psi Mearlcrete Min. 300 psi Elastizell Min. 300 psi Concrecel Min. 200 psi Cellular Lightweight Concrete UltraPly TPO XR with SBS Modified Roofing s APPENDIX A Min. 3.4-inch wide side-laps; Min. 6-inch end laps; Side-laps shall be installed perpendicular to the direction of the steel deck ribs and parallel to the direction of the wood trusses for mechanically attached systems Min. 2-inch wide side-laps; Side-laps shall be installed perpendicular to the direction of the steel deck ribs for mechanically attached systems Min. 2-inch wide side-laps with min. 1.5-inch wide heat weld; Self-adhered; Min. 3-inch side laps; Min. 6-inch end laps; ; All substrates except metal decks must be primed; Prime surface with Firestone SA-Solvent Based (SB) Primer or Firestone SA-LVOC Primer at a rate of 0.5 gal/100ft 2 or Firestone SA-Water Based (WB) Primer gal/100ft 2 ; Slurry coat min. 1/8-inch thick; 1-inch thick EPS board (1 lbs/ft 3 ); Min. 2-inch thick top coat; Celcore PVA curing compound applied at rate of 300 ft 2 /gal Deck is treated by applying a continuous film with a broom prior to placement of the Celcore lightweight concrete Slurry coat min. 1/8-inch thick; Min. 1-inch thick EPS board (1 lbs/ft 3 ); Min. 2-inch top coat FBP FL# R2 Page 2 of 6 This evaluation report is provided for State of Florida product approval under Rule 61G20-3. The manufacturer shall notify CREEK of any product changes or quality assurance changes throughout the duration for which this report is valid. This evaluation report does not express nor imply warranty, installation, recommended use, or other product attributes that are not specifically addressed herein.

8 [NOMENCLATURE] Description Insulation/Cover Board Fastening Patterns Fastening Pattern UltraPly TPO XR with SBS Modified Roofing s APPENDIX A 4 per 4 ft x 4 ft board (Max. 4.0ft 2 contributory area per fastener) 8 per 4 ft x 4 ft Board (Max. 2.0ft 2 contributory area per fastener) 5 per 4 ft x 8 ft board (Max. 6.4ft 2 contributory area per fastener) FBP FL# R2 Page 3 of 6 This evaluation report is provided for State of Florida product approval under Rule 61G20-3. The manufacturer shall notify CREEK of any product changes or quality assurance changes throughout the duration for which this report is valid. This evaluation report does not express nor imply warranty, installation, recommended use, or other product attributes that are not specifically addressed herein.

9 [NOMENCLATURE] Description Insulation/Cover Board Fastening Patterns Fastening Pattern UltraPly TPO XR with SBS Modified Roofing s APPENDIX A 8 per 4 ft. x 8 ft. board (Max. 4.00ft 2 contributory area per fastener) 10 per 4 ft. x 8 ft. board (Max. 3.2ft 2 contributory area per fastener) 12 per 4 ft x 8 ft board (Max. 2.67ft 2 contributory area per fastener) FBP FL# R2 Page 4 of 6 This evaluation report is provided for State of Florida product approval under Rule 61G20-3. The manufacturer shall notify CREEK of any product changes or quality assurance changes throughout the duration for which this report is valid. This evaluation report does not express nor imply warranty, installation, recommended use, or other product attributes that are not specifically addressed herein.

10 [NOMENCLATURE] Description Insulation/Cover Board Fastening Patterns Fastening Pattern UltraPly TPO XR with SBS Modified Roofing s APPENDIX A 15 per 4 ft x 8 ft board (Max. 2.13ft 2 contributory area per fastener) 18 per 4 ft x 8 ft board (Max. 1.78ft 2 contributory area per fastener) 20 per 4 ft x 8 ft board (Max. 1.60ft 2 contributory area per fastener) FBP FL# R2 Page 5 of 6 This evaluation report is provided for State of Florida product approval under Rule 61G20-3. The manufacturer shall notify CREEK of any product changes or quality assurance changes throughout the duration for which this report is valid. This evaluation report does not express nor imply warranty, installation, recommended use, or other product attributes that are not specifically addressed herein.

11 [NOMENCLATURE] Description Insulation/Cover Board Fastening Patterns Fastening Pattern UltraPly TPO XR with SBS Modified Roofing s APPENDIX A 22 per 4 ft x 8 ft board (Max. 1.45ft 2 contributory area per fastener) 24 per 4 ft x 8 ft board (Max. 1.33ft 2 contributory area per fastener) 32 per 4 ft x 8 ft board (Max. 1.00ft 2 contributory area per fastener) FBP FL# R2 Page 6 of 6 This evaluation report is provided for State of Florida product approval under Rule 61G20-3. The manufacturer shall notify CREEK of any product changes or quality assurance changes throughout the duration for which this report is valid. This evaluation report does not express nor imply warranty, installation, recommended use, or other product attributes that are not specifically addressed herein.

12 UltraPly TPO XR with SBS Modified Roofing s NOMENCLATURE The following naming conventions are utilized to specify products in the APPROVED ASSEMBLIES section of this report. Refer to the nomenclature below when deciphering the allowable products for use in the selected assembly. Installation requirements shall be as noted in the APPROVED ASSEMBLIES and INSTALLATION section of this report. Name AP Fasteners & Plates As Tested CD Fasteners & Plates Cover Board Deck Detail DensDeck HA SBS Ply HD Fasteners & Plates Definition Firestone All-Purpose Fasteners or All-Purpose S Fasteners and Insulation Fastening Plates Information provided to the report user based on the as tested condition of the roof system One ply of SA. Subsequent ply shall be applied in hot asphalt or by torch or shall be UltraPly TPO XR membrane applied in hot asphalt only. Firestone Concrete Drive and Insulation Fastening Plates One layer of any of the following products: -Georgia-Pacific DensDeck -Georgia-Pacific -Firestone ISOGARD HD -GenFlex HD ISO -USG Glass-Mat Roof Board -USG Gypsum-Fiber Roof Board As Tested deck construction details are described as follows: Concrete Deck Min. f c = 2,500 psi at 28 days CWF Deck Min. 2.5-inch thick Tectum I cementitious wood fiber panels Steel Deck Min. 22 ga, Wide Rib Deck (Type WR) conforming to ANSI/SDI-RD1.0 & FBC; 0.5% Vented for LWIC applications only. The following nomenclature is used to further describe the As Tested condition. F<#> <#> #12-24 HWH self-drilling screws or equivalent fastener at each flute used to secure the deck to the structural supports; Min inch penetration G<#> Min. Grade <#> of Steel Deck L<#> Max. span of <#> ft P Min. 5/8-inch diameter puddle welds at each flute used to secure the deck to the structural supports S<#> 1/4-14 HWH x7/8 self-drilling screws or equivalent fastener secured <#>-inch o.c. along the panel side laps W 0.75-inch O.D. flat washer used with indicated fastener Wood Deck APA Span-Rated plywood sheathing. The following nomenclature is used to further describe the As Tested condition. T<#> Min. <#>-inch thickness of the plywood L<#> Max. span of <#> inches N<#> Min inch diameter x 2-3/8-inch ring shank nails spaced <#>-inch o.c. at all intermediate supports and at the perimeter of each board Min inch Georgia-Pacific DensDeck Min inch Georgia-Pacific One or more plies of MB Base, SBS, Base, SBS Poly Base, SBS Premium Poly Base, SBS Premium Base, or SBS Smooth fully bonded in ASTM D 312, Type IV hot asphalt One or more plies of SBS, Base, SBS Poly Base, SBS Premium Poly Base, SBS Premium Base, or SBS Smooth fully bonded in ASTM D 312, Type IV hot asphalt Firestone Heavy Duty Fasteners and Insulation Fastening Plates FBP FL# R2 Page 1 of 28 This evaluation report is provided for State of Florida product approval under Rule 61G20-3. The manufacturer shall notify CREEK of any product changes or

13 UltraPly TPO XR with SBS Modified Roofing s Name Insulation II III ISO ISO HD ISO HD-C ISO GF LWIC MA Base MA Base II MA Base III MA Base IV MCRF Preliminarily Secured Recover SBS Base Sheet SBS TA Vapor Barrier TPO XR HA TPO XR XRS Definition One of more layers in any combination of: -Georgia-Pacific DensDeck -Georgia-Pacific -Firestone ISO 95+ GL -Firestone ISOGARD HD -Firestone ISOGARD HD Composite -Firestone RESISTA -GenFlex ISO Insulation -GenFlex HD ISO -GenFlex HD Composite ISO -GenFlex Coated Glass Facer -USG Glass-Mat Roof Board -USG Gypsum-Fiber Roof Board I.S.O. Twin Pack Adhesive, I.S.O. Stick, or I.S.O. Fix II Adhesive I.S.O. Twin Pack Adhesive, I.S.O. Stick, I.S.O. Fix II Adhesive, I.S.O. Spray R, or Twin Jet I.S.O. Twin Pack Adhesive, I.S.O. Stick, I.S.O. Fix II Adhesive, or Twin Jet One or more layers of GenFlex ISO Insulation or Firestone ISO 95+ GL One or more layers of GenFlex HD ISO or Firestone ISOGARD HD One or more layers of GenFlex HD Composite ISO or Firestone ISOGARD HD Composite One or more layers of GenFlex Coated Glass Facer or Firestone RESISTA Poured-in-place Cellular Lightweight Concrete with encapsulated insulation board One ply of Channel Venting Base, MB Base, SBS Base, SBS Glass Torch Base, SBS Glass Torch Base 1.5, SBS Premium Base, SBS Poly Base, SBS Premium Poly Base, SBS Poly Torch Base, or SBS Smooth mechanically attached as prescribed per the approved assembly One ply of MB Base, SBS Base, SBS Glass Torch Base, SBS Glass Torch Base 1.5, SBS Premium Base, SBS Poly Base, SBS Premium Poly Base, SBS Poly Torch Base, or SBS Smooth mechanically attached as prescribed per the approved assembly One ply of SBS Base, SBS Glass Torch Base, SBS Glass Torch Base 1.5, SBS Premium Base, SBS Poly Base, SBS Premium Poly Base, SBS Poly Torch Base, or SBS Smooth mechanically attached as prescribed per the approved assembly One ply of Channel Venting Base, SBS Base, SBS Base-P, SBS Glass Torch Base, SBS Glass Torch Base 1.5, SBS Poly Torch Base Minimum Characteristic Resistance Force as determined by TAS 105 for the named fastener in the selected assembly Maximum Design Pressure Fastened at minimum rate of 5 per 4 ft x 8 ft board or 4 per 4 ft x 4 ft board. Where assemblies are used to recover an existing roof, the existing roof shall consist of only one layer of roofing, i.e. recovering a previously recovered roof is not permitted. Recover roofing shall be conducted in compliance with FBC Section 1511 outside of the HVHZ and FBC Section 1521 within the HVHZ. For mechanically fastened roof assemblies, the existing roof insulation thickness may be contributory in meeting the minimum insulation thickness requirements for a given assembly. One ply of SBS Base, SBS Glass Torch Base, SBS Poly Base, SBS Premium Poly Base, SBS Poly Torch Base, SBS Premium Base, or SBS Smooth SBS Glass Torch Base torched adhered over primed concrete deck Min inch USG Gypsum-Fiber Roof Board One or more plies of SBS Glass Torch Base, SBS Glass Torch Base 1.5 or SBS Poly Torch Base fully bonded by torch adhering One ply of UltraPly TPO XR 100, 115, 135 applied in ASTM D 312, Type IV asphalt or Owens Corning PermaMop asphalt One ply of UltraPly TPO XR 100, 115, 135 applied in XR Stick Membrane Adhesive max. One ply of UltraPly TPO XR 100, 115, 135 applied in I.S.O. Spray R spaced max. FBP FL# R2 Page 2 of 28 This evaluation report is provided for State of Florida product approval under Rule 61G20-3. The manufacturer shall notify CREEK of any product changes or

14 UltraPly TPO XR with SBS Modified Roofing s Name V-Force Definition One ply of Firestone V-Force Vapor Barrier Membrane FBP FL# R2 Page 3 of 28 This evaluation report is provided for State of Florida product approval under Rule 61G20-3. The manufacturer shall notify CREEK of any product changes or

15 UltraPly TPO XR with SBS Modified Roofing s APPROVED ASSEMBLIES The following notes shall be observed when using the assembly tables below. 1. s were calculated using a 2:1 margin of safety per FBC Section and Refer to LIMITATIONS and NOMENCLATURE sections of this evaluation when using the table(s) below. 3. Refer to INSTALLATION section of this report for installation detail when the information is not explicitly stated for the selected assembly. 4. The on-center (o.c.) spacing given is the maximum allowable attachment spacing for the rated system. 5. As Tested information for roof deck construction is provided for information only. The addition of the As Tested deck information does not obviate the requirement for rational design of the roof deck and roof deck attachment in accordance with FBC requirements. 6. Prior to application of the approved assembly an optional vapor barrier, such as 4-6 mil polyethylene, V-Force, or with V-Force, may be installed over concrete or steel decks when the approved assembly contains insulation or the membrane fastened through to the deck. C-A-# C-AM-# CW-A-# LC-A-# LC-AM-# LC-M-# LS-A-# LS-AM-# LS-M-# R-AM-# R-M-# S-AM-# S-M-# W-AM-# W-M-# Assembly Numbers and Definitions Assemblies with All Layers Adhered over Concrete Deck (New or Existing) Assemblies with Adhered Membranes over Fastened Insulation over Concrete Deck (New, Existing, or Recover) Adhered Assemblies over Cementitious Wood Fiber Deck (New or Existing) Lightweight Concrete Assemblies with All Layers Adhered over Concrete Deck (New or Existing) Lightweight Concrete Assemblies with Adhered Membranes over Fastened Insulation or Anchor Sheet over Concrete Deck (New or Existing) Mechanically Fastened Lightweight Concrete Assemblies over Concrete Deck (New or Existing) Lightweight Concrete Assemblies with All Layers Adhered over Steel Deck (New or Existing) Lightweight Concrete Assemblies with Adhered Membranes over Fastened Insulation or Anchor Sheet over Steel Deck (New or Existing) Mechanically Fastened Lightweight Concrete Assemblies over Steel Deck (New or Existing) Recover Assemblies with Adhered Membranes over Fastened Insulation Recover Assemblies with Mechanically Fastened Base Sheet Assemblies with Adhered Membranes over Fastened Insulation over Steel Deck (New, Existing, or Recover) Mechanically Fastened Assemblies over Steel Deck (New, Existing, or Recover) Assemblies with Adhered Membranes over Fastened Insulation over Wood Deck (New, Existing, or Recover) Mechanically Fastened Assemblies over Wood Deck (New, Existing, or Recover) Assemblies with All Layers Adhered over Concrete Deck (New or Existing) Vapor Barrier Base Insulation Top Insulation Cover Board Base Ply Ply Sheet Membrane C-A-1 - ISO II ribbon applied in - Min. 1-inch ISO I.S.O. Twin Pack spaced -105 FBP FL# R2 Page 4 of 28 This evaluation report is provided for State of Florida product approval under Rule 61G20-3. The manufacturer shall notify CREEK of any product changes or

16 UltraPly TPO XR with SBS Modified Roofing s Assemblies with All Layers Adhered over Concrete Deck (New or Existing) Vapor Barrier Base Insulation Top Insulation Cover Board Base Ply Ply Sheet Membrane C-A-2 - ISO II ribbon applied in - ISO HD spaced -110 C-A-3 - ISO II ribbon applied in - installed with I.S.O. Twin Pack spaced, C-A-4 - ISO ASTM D 312, Type IV Asphalt - installed with ASTM D 312, Type IV Asphalt, -130 C-A-5 - ISO III ribbon applied in - III ribbon applied in, or or C-A-6 - ISO II ribbon applied in - I.S.O. Stick or Twin Jet spaced, or or -175 C-A-7 - ISO II ribbon applied in 6-inch o.c. - II ribbon applied in 6-inch o.c. HA SBS Ply or or -230 C-A-8 - ISO II ribbon applied in 6-inch o.c. - II ribbon applied in 6-inch o.c FBP FL# R2 Page 5 of 28 This evaluation report is provided for State of Florida product approval under Rule 61G20-3. The manufacturer shall notify CREEK of any product changes or

17 UltraPly TPO XR with SBS Modified Roofing s Assemblies with All Layers Adhered over Concrete Deck (New or Existing) Vapor Barrier Base Insulation Top Insulation Cover Board Base Ply Ply Sheet Membrane C-A-9 C-A-10 C-A-11 C-A-12 C-A-13 C-A-14 V-Force V-Force V-Force or 1-2 ply of Ply IV or VI in hot asphalt or APP 80 Glass Base, SBS Glass FR Torch, or SBS Poly Torch Base torch adhered V-Force V-Force V-Force ISO I.S.O. Stick applied in Taper ISO installed with I.S.O. Stick spaced ISO I.S.O. Twin Pack or I.S.O. Spray R applied in ISO I.S.O. Twin Pack or I.S.O. Stick applied in ISO I.S.O. Stick applied in 6-inch o.c. ISO I.S.O. Stick applied in 6-inch o.c. Min. 1-inch ISO I.S.O. Stick spaced ISO HD or I.S.O. Stick spaced - ISO I.S.O. Stick applied in - ISO HD or DensDeck Prime I.S.O. Twin Pack or I.S.O. Spray R spaced - - Min. 1-inch ISO I.S.O. Stick spaced 6-inch o.c. Min. 1-inch ISO I.S.O. Stick spaced 6-inch o.c. - installed with I.S.O. Stick spaced HA SBS Ply, or HA SBS Ply, or HA SBS Ply, or HA SBS Ply, or HA SBS Ply, or HA SBS Ply, or TPO XR HA TPO XR HA TPO XR HA TPO XR HA TPO XR HA TPO XR HA FBP FL# R2 Page 6 of 28 This evaluation report is provided for State of Florida product approval under Rule 61G20-3. The manufacturer shall notify CREEK of any product changes or

18 UltraPly TPO XR with SBS Modified Roofing s Assemblies with All Layers Adhered over Concrete Deck (New or Existing) Vapor Barrier Base Insulation Top Insulation Cover Board Base Ply Ply Sheet Membrane C-A-15 V-Force or 1-2 ply of Ply IV or VI in hot asphalt or APP 80 Glass Base, SBS Glass FR Torch, or SBS Poly Torch Base torch adhered ISO I.S.O. Twin Pack or I.S.O. Spray R applied in - - HA SBS Ply, or TPO XR HA C-A-16 - ISO I.S.O. Stick applied in 6-inch o.c. Min. 1-inch ISO I.S.O. Stick spaced 6-inch o.c. installed with I.S.O. Stick spaced HA SBS Ply, or TPO XR HA C-A-17 - ISO ribbon applied in 6-inch o.c. - installed with I.S.O. Stick spaced 6-inch o.c., or HA SBS Ply, or TPO XR HA C-A-18 V-Force or 1-2 ply of Ply IV or VI in hot asphalt or APP 80 Glass Base, SBS Glass FR Torch, or SBS Poly Torch Base torch adhered ISO I.S.O. Twin Pack or I.S.O. Spray R applied in - installed with I.S.O. Twin Pack or I.S.O. Spray R spaced, or HA SBS Ply, or TPO XR HA FBP FL# R2 Page 7 of 28 This evaluation report is provided for State of Florida product approval under Rule 61G20-3. The manufacturer shall notify CREEK of any product changes or

19 UltraPly TPO XR with SBS Modified Roofing s Assemblies with All Layers Adhered over Concrete Deck (New or Existing) Vapor Barrier Base Insulation Top Insulation Cover Board Base Ply Ply Sheet Membrane C-A-19 V-Force or 1-2 ply of Ply IV or VI in hot asphalt or APP 80 Glass Base, SBS Glass FR Torch, or SBS Poly Torch Base torch adhered ISO I.S.O. Twin Pack or I.S.O. Spray R applied in - installed with I.S.O. Twin Pack or I.S.O. Spray R spaced or or SBS Poly Base or SBS Smooth in ASTM D 312, Type IV Asphalt HA SBS Ply, or TPO XR HA -400 C-A-20 - installed with I.S.O. Stick spaced 6-inch o.c. - - or HA SBS Ply, or TPO XR HA -400 C-A-21 - installed with I.S.O. Stick spaced 6-inch o.c. - - SBS Poly Base or SBS Smooth in ASTM D 312, Type IV Asphalt HA SBS Ply, or TPO XR HA -400 Assemblies with Adhered Membranes over Fastened Insulation over Concrete Deck (New, Existing, or Recover) Base Insulation Top Insulation Insulation Attachment Base Ply Ply Sheet Membrane C-AM-1 ISO or ISO GF ISO HD-C at 8 per 4 ft x 8 ft board or C-AM-2 secured with CD Fasteners & Plates or HD Fasteners & Insulation Plates at 8 per 4 ft x 8 ft board followed by V-Force ISO I.S.O. Stick or Twin Jet applied in or FBP FL# R2 Page 8 of 28 This evaluation report is provided for State of Florida product approval under Rule 61G20-3. The manufacturer shall notify CREEK of any product changes or

20 UltraPly TPO XR with SBS Modified Roofing s Assemblies with Adhered Membranes over Fastened Insulation over Concrete Deck (New, Existing, or Recover) Base Insulation Top Insulation Insulation Attachment Base Ply Ply Sheet Membrane C-AM-3 secured with CD Fasteners & Plates or HD Fasteners & Insulation Plates at 8 per 4 ft x 8 ft board followed by V-Force Layer 1: ISO (Tapered) Layer 2: ISO HD or, Layer 1 & Layer 2 adhered in I.S.O. Stick or Twin Jet applied in or w/ only or C-AM-4 Min. 2-inch ISO at 12 per 4 ft x 8 ft board or C-AM-5 HD Fasteners & Plates at 10 per 4 ft x 8 ft board or C-AM-6 Min inch HD Fasteners & Plates at 8 per 4 ft x 8 ft board or C-AM-7 Min. 2-inch ISO, ISO (Tapered)or ISO GF at 18 per 4 ft x 8 ft board or or C-AM-8 Min. 2-inch ISO HD-C laid perpendicular to flutes with staggered end joints at 8 per 4 ft x 8 ft board or C-AM-9 Min 2.5-inch ISO at 15 per 4 ft x 8 ft board or (Lim 7) C-AM-10 Min. 1-inch ISO HD at 24 per 4 ft x 8 ft board or C-AM-11 ISO HD-C at 12 per 4 ft x 8 ft board or FBP FL# R2 Page 9 of 28 This evaluation report is provided for State of Florida product approval under Rule 61G20-3. The manufacturer shall notify CREEK of any product changes or

21 UltraPly TPO XR with SBS Modified Roofing s Assemblies with Adhered Membranes over Fastened Insulation over Concrete Deck (New, Existing, or Recover) Base Insulation Top Insulation Insulation Attachment Base Ply Ply Sheet Membrane C-AM-12 ISO at 18 per 4 ft x 8 ft board or C-AM-13 Min. 1-inch at 15 per 4 ft x 8 ft board or C-AM-14 Min 0.5-inch ISO 95+GL or ISO GF at 18 per 4 ft x 8 ft board or - C-AM-15 One or more layers of ISO or ISO GF at 18 per 4 ft x 8 ft board (min inch side laps) (min inch side laps) C-AM-16 One or more layers of ISO or ISO GF at 18 per 4 ft x 8 ft board or C-AM-17 Min. 1-inch ISO GF or at 20 per 4 ft x 8 ft board or C-AM-18 Min. 2-inch ISO, ISO GF or ISO (Tapered) at 18 per 4 ft x 8 ft board or II or II C-AM-19 One or more layers of ISO or ISO GF at 24 per 4 ft x 8 ft board or TA SBS Ply C-AM-20 One or more layers of ISO or ISO GF at 24 per 4 ft x 8 ft board or, or C-AM-21 One or more layers of ISO or ISO GF at 18 per 4 ft x 8 ft board (min inch side laps) (min inch side laps) C-AM-22 One or more layers of ISO or ISO GF at 18 per 4 ft x 8 ft board or FBP FL# R2 Page 10 of 28 This evaluation report is provided for State of Florida product approval under Rule 61G20-3. The manufacturer shall notify CREEK of any product changes or

22 UltraPly TPO XR with SBS Modified Roofing s Assemblies with Adhered Membranes over Fastened Insulation over Concrete Deck (New, Existing, or Recover) Base Insulation Top Insulation Insulation Attachment Base Ply Ply Sheet Membrane C-AM-23 ISO HD-C at 18 per 4 ft x 8 ft board or C-AM-24 Min. 2-inch ISO, ISO GF or ISO (Tapered) at 20 per 4 ft x 8 ft board or II or II C-AM-25 ISO at 22 per 4 ft x 8 ft board (min inch side laps) or (min inch side laps) -90 C-AM-26 Min 2.5-inch ISO- at 32 per 4 ft x 8 ft board or (Lim 7) C-AM-27 Min. 2-inch ISO, ISO GF or ISO (Tapered) at 24 per 4 ft x 8 ft board or or C-AM-28 ISO at 32 per 4 ft x 8 ft board -150 C-AM-29 Min. 2-inch ISO, ISO GF or ISO (Tapered) at 32 per 4 ft x 8 ft board or or Adhered Assemblies over Cementitious Wood Fiber Deck (New or Existing) Base Insulation Base Attachment Top Insulation Top Attachment Base Ply Ply Sheet Membrane CW-A-1 Min. 400 psi Celcore MF with HS Rheology Admixture Poured-in-place I.S.O. Sick or Twin Jet, or HA SBS BUR Ply, or -145 CW-A-2 ISO I.S.O. Stick Ribbons spaced I.S.O. Sick or Twin Jet, or HA SBS BUR Ply, or FBP FL# R2 Page 11 of 28 This evaluation report is provided for State of Florida product approval under Rule 61G20-3. The manufacturer shall notify CREEK of any product changes or

23 UltraPly TPO XR with SBS Modified Roofing s Lightweight Concrete Assemblies with All Layers Adhered over Concrete Deck (New or Existing) Vapor Barrier LWIC Insulation/ Cover Board Insulation/Cover Board Attachment Base Ply Ply Sheet Membrane LC-A-1 SBS TA Vapor Barrier Min. 300 psi LWIC Min. 2-inch ISO CD Fasteners & Plates or HD Fasteners & Insulation Plates at a rate of 18 per 4 ft x 8 ft board or LC-A-2 - Min. 200 psi Cellular Lightweight Concrete (MCRF 80 lbf using Firestone 1.7-inch LWC Base-Ply Fastener) I.S.O. Stick or Twin Jet, or or LC-A-3 - Min. 200 psi Cellular Lightweight Concrete (MCRF 80 lbf using Firestone 1.7-inch LWC Base-Ply Fastener) ISO HD I.S.O. Twin Pack or Twin Jet, or or LC-A-4 SBS TA Vapor Barrier Min. 300 psi I.S.O. Stick or Twin Jet, or or -106 LC-A-5 SBS TA Vapor Barrier Min. 300 psi ISO HD I.S.O. Twin Pack or Twin Jet, or or -106 LC-A-6 SBS TA Vapor Barrier Min. 400 psi III, or or FBP FL# R2 Page 12 of 28 This evaluation report is provided for State of Florida product approval under Rule 61G20-3. The manufacturer shall notify CREEK of any product changes or

24 UltraPly TPO XR with SBS Modified Roofing s Lightweight Concrete Assemblies with All Layers Adhered over Concrete Deck (New or Existing) Vapor Barrier LWIC Insulation/ Cover Board Insulation/Cover Board Attachment Base Ply Ply Sheet Membrane LC-A-7 - LC-A-8 - Min. 350 psi Min. 350 psi Min. 1-inch ISO or ISO GF, Min. 2-inch ISO HS-C, or ISO HD; or followed by ISO HD ISO or ISO GF followed by I.S.O. Twin Pack, I.S.O. Stick, or Twin Jet I.S.O. Twin Pack, I.S.O. Stick, or Twin Jet or or or LC-A-9 - Min. 300 psi ISO HD III or LC-A-10 - Min. 300 psi I.S.O. Stick or Twin Jet or LC-A-11 - Min. 300 psi Min. 1-inch ISO III; Ribbons spaced 12-inch o.c. or LC-A-12 - Min. 350 psi Min. 1-inch ISO GF I.S.O. Twin Pack Ribbons spaced LC-A-13 - Min. 350 psi Min. 1-inch ISO or ISO GF, or Min. 2-inch ISO HD-C I.S.O. Stick Ribbons spaced HA SBS Ply or FBP FL# R2 Page 13 of 28 This evaluation report is provided for State of Florida product approval under Rule 61G20-3. The manufacturer shall notify CREEK of any product changes or

25 UltraPly TPO XR with SBS Modified Roofing s Lightweight Concrete Assemblies with All Layers Adhered over Concrete Deck (New or Existing) Vapor Barrier LWIC Insulation/ Cover Board Insulation/Cover Board Attachment Base Ply Ply Sheet Membrane LC-A-14 - Min. 350 psi followed by ISO HD I.S.O. Stick Ribbons spaced HA SBS Ply or LC-A-15 - Min. 350 psi followed by I.S.O. Stick Ribbons spaced HA SBS Ply LC-A-16 - Min. 350 psi followed by or ISO HD I.S.O. Twin Pack Ribbons spaced HA SBS Ply LC-A-17 - Min. 350 psi Min. 2-inch ISO HD-C I.S.O. Twin Pack Ribbons spaced HA SBS Ply LC-A-18 - Min. 350 psi Min. 1-inch ISO GF I.S.O. Twin Pack Ribbons spaced HA SBS Ply LC-A-19 - Min. 350 psi Min. 1-inch ISO I.S.O. Twin Pack Ribbons spaced -210 LC-A-20 - Min. 350 psi Min. 1-inch ISO I.S.O. Twin Pack Ribbons spaced HA SBS Ply LC-A-21 - Min. 350 psi Min. 2-inch ISO HD-C or ISO or ISO GF followed by ISO HD I.S.O. Twin Pack Ribbons spaced FBP FL# R2 Page 14 of 28 This evaluation report is provided for State of Florida product approval under Rule 61G20-3. The manufacturer shall notify CREEK of any product changes or

26 UltraPly TPO XR with SBS Modified Roofing s Lightweight Concrete Assemblies with All Layers Adhered over Concrete Deck (New or Existing) Vapor Barrier LWIC Insulation/ Cover Board Insulation/Cover Board Attachment Base Ply Ply Sheet Membrane LC-A-22 SBS TA Vapor Barrier Min. 400 psi Celcore MF with HS Ribbons spaced 12-inch o.c., or or Lightweight Concrete Assemblies with Adhered Membranes over Fastened Insulation or Anchor Sheet over Concrete Deck (Existing) LWIC Anchor Sheet Insulation Cover Board Base Ply Ply Sheet Membrane LC-AM-1 LC-AM-2 Mearlcrete, Celcore, or Celcore MF with HS Rheology Admixture Mearlcrete, Celcore, or Celcore MF with HS Rheology Admixture MA Base secured with 1.8-inch Two- Piece Impact Nail installed 7-inch o.c. in the 4-inch wide laps, 7-inch o.c. in two (2) staggered rows in the field MA Base secured with 1.8-inch Two- Piece Impact Nail installed 7-inch o.c. in the 4-inch wide laps, 7-inch o.c. in two (2) staggered rows in the field Min. 1-inch ISO or ISO GF spaced Min. 1-inch ISO or ISO GF spaced Followed by ISO (Tapered) or Tapered ISO GF spaced ISO (Tapered) or Tapered ISO GF spaced spaced or or FBP FL# R2 Page 15 of 28 This evaluation report is provided for State of Florida product approval under Rule 61G20-3. The manufacturer shall notify CREEK of any product changes or

27 UltraPly TPO XR with SBS Modified Roofing s Mechanically Fastened Lightweight Concrete Assemblies over Concrete Deck (New or Existing) LWIC Base Sheet Base Sheet Attachment Ply Sheet Membrane LC-M-1 Min. 300 psi SBS PolyBase 1.7-inch LWC Base-Ply Fastener installed 9-inch o.c. in the 3.4-inch wide side laps, 9- inch o.c. in two (2) equally spaced, staggered rows in the field, or Non - LC-M-2 Min. 350 psi Elastizell SBS Poly Torch Base 1.8-inch Twin Loc-Nails and Straight Line Batten Bars secured 6-inch o.c. within the torch adhered, 4-inch wide side laps SBS Poly Torch Base Torch adhered LC-M-3 Min. 300 psi Mearlcrete MA Base 1.7-inch LWC Base-Ply Fastener installed 7-inch o.c. in the laps, 7-inch o.c. in two (2) equally spaced, staggered rows in the field or LC-M-4 Min. 300 psi Elastizell SBS Base Sheet 1.7-inch LWC Base-Ply Fastener installed 9-inch o.c. in the laps, 9-inch o.c. in two (2) staggered rows in the field LC-M-5 Min. 380 psi SBS Base Sheet 1.8-inch Two-Piece Impact Nail installed 8- inch o.c. in the laps, 8-inch o.c. in two (2) staggered rows in the field, or LC-M-6 Min. 200 psi Cellular Lightweight Concrete (MCRF 176 lbf) MA Base 1.7-inch LWC Base-Ply Fastener installed 7-inch o.c. in the laps, 7-inch o.c. in two (2) equally spaced, staggered rows in the field or LC-M-7 Min. 300 psi MA Base 1.7-inch LWC Base-Ply Fastener installed 7-inch o.c. in the laps, 7-inch o.c. in two (2) equally spaced, staggered rows in the field or LC-M-8 Min. 380 psi MA Base 1.7-inch LWC Base-Ply Fastener installed 8-inch o.c. in the laps, 8-inch o.c. in two (2) staggered rows in the field or LC-M-9 Min. 360 psi Channel Venting Base, SBS Base, SBS Glass Torch Base, SBS Glass Torch Base 1.5 or SBS PolyTorch Base 1.8-inch Two-Piece Impact Nail installed 7- inch o.c. in the laps, 7-inch o.c. in two (2) staggered rows in the field, LC-M-10 Min. 300 psi MA Base 1.7-inch LWC Base-Ply Fastener installed 7-inch o.c. in the laps, 7-inch o.c. in two (2) staggered rows in the field FBP FL# R2 Page 16 of 28 This evaluation report is provided for State of Florida product approval under Rule 61G20-3. The manufacturer shall notify CREEK of any product changes or