SCOPE OF ACCREDITATION TO ISO/IEC 17025:2005

Transcription

1 SCOPE OF ACCREDITATION TO ISO/IEC 17025:2005 GORRONDONA ENGINEERING SERVICES, INC Kennedy Commerce Drive Houston, TX Corey Ritter Phone: Valid To: August 31, 2020 Certificate Number: In recognition of the successful completion of the A2LA evaluation process, accreditation is granted to this laboratory for: CONSTRUCTION MATERIALS ENGINEERING ASTM: C1077 (Standard Practice for Agencies Testing Concrete and Concrete Aggregates for Use in Construction and Criteria for Testing Agency Evaluation); D3666 (Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials); D3740 (Standard Practice for Minimum Requirements for Agencies Engaged in Testing and/or Inspection of Soil and Rock as Used in Engineering Design and Construction); E329 (Standard Specification for Agencies Engaged in Construction Inspection, Testing, or Special Inspection) CONSTRUCTION MATERIALS TESTING Test Method: Aggregates: ASTM C29 ASTM C40 ASTM C117 ASTM C127 ASTM C128 ASTM C136 ASTM C566 ASTM C702 ASTM D75 1 Tex-400-A 1 Tex-401-A Tex-403-A Tex-404-A Tex-406-A Tex-409-A Bulk Density ( Unit Weight ) and Voids in Aggregate Organic Impurities in Fine Aggregates for Concrete Materials Finer than 75-μm (No. 200) Sieve in Mineral Aggregates by Washing Density, Relative Density (Specific Gravity), and Absorption of Coarse Aggregate Density, Relative Density (Specific Gravity), and Absorption of Fine Aggregate Sieve Analysis of Fine and Coarse Aggregates Total Evaporable Moisture Content of Aggregate by Drying Reducing Samples of Aggregate to Testing Size Sampling Aggregates Sampling Flexible Base, Stone, Gravel, Sand, and Mineral Aggregate Sieve Analysis of Fine and Coarse Aggregate Saturated Surface-Dry Specific Gravity and Absorption of Aggregates Determining Unit Mass (Weight) of Aggregates Material Finer Than 75 µm (No. 200) Sieve in Mineral Aggregates (Decantation Test for Concrete Aggregates) Free Moisture and Water Absorption in Aggregate for Concrete (A2LA Cert. No ) 09/05/2018 Page 1 of 4

2 Asphalt: ASTM D9791 ASTM D1560 ASTM D2041 ASTM D2726 ASTM D2950/D ASTM D3549 (Method A only) 1 ASTM D ASTM D6307 Tex-201-F Tex-206-F Tex-207-F (Part VI, VII and VII) Tex-208-F Tex-227-F Tex-236-F Concrete: ASTM C31/C31M 1 ASTM C39/C39M ASTM C42/C42M ASTM C78/C78M 1 ASTM C138/C138M 1 ASTM C143/C143M 1 ASTM C172/C172M 1 ASTM C173 1 ASTM C192/C192M ASTM C231/C231M 1 ASTM C293/C293M ASTM C617 ASTM C1064/C1064M 1 ASTM C1231/C1231M Tex-407-A 1 Tex-414-A 1 Tex-415-A 1 Tex-416-A 1 Tex-417-A 1 Tex-418-A Tex-422-A Tex-450-A Sampling Bituminous Paving Mixtures Resistance to Deformation and Cohesion of Bituminous Mixtures by Means of Hveem Apparatus Theoretical Maximum Specific Gravity and Density of Bituminous Paving Mixtures Bulk Specific Gravity and Density of Non-Absorptive Compacted Bituminous Mixtures Density of Bituminous Concrete in Place by Nuclear Methods Thickness or Height of Compacted Bituminous Paving Mixture Specimens Sampling Compacted Bituminous Mixtures for Laboratory Testing Asphalt Content of Hot-Mix Asphalt by Ignition Method Bulk Specific Gravity and Water Absorption of Aggregate Compacting Specimens Using the Texas Gyratory Compactor (TGC) Determining Density of Compacted Bituminous Mixtures Test for Stabilometer Value of Bituminous Mixtures Theoretical Maximum Specific Gravity of Bituminous Mixtures Determining Asphalt Content from Asphalt Paving Mixtures by the Ignition Method Making and Curing Concrete Test Specimens in the Field Compressive Strength of Cylindrical Concrete Specimens Obtaining and Testing Drilled Cores and Sawed Beams of Concrete Flexural Strength of Concrete (Using Simple Beam with Third-Point Loading) Density (Unit Weight), Yield, and Air Content (Gravimetric) of Concrete Slump of Hydraulic-Cement Concrete Sampling Freshly Mixed Concrete Air Content of Freshly Mixed Concrete by the Volumetric Method Making and Curing Concrete Test Specimens in the Laboratory Air Content of Freshly Mixed Concrete by the Pressure Method Flexural Strength of Concrete (Using Simple Beam With Center-Point Loading) Capping Cylindrical Concrete Specimens Temperature of Freshly Mixed Hydraulic-Cement Concrete Unbonded Caps in Determination of Compressive Strength of Hardened Concrete Cylinders Sampling Freshly Mixed Concrete Air Content of Freshly Mixed Concrete by the Volumetric Method Slump of Hydraulic Cement Concrete Air Content of Freshly Mixed Concrete by the Pressure Method Unit Weight, Yield, and Air Content (Gravimetric) of Concrete Compressive Strength of Cylindrical Concrete Specimens Measuring Temperature of Freshly Mixed Portland Cement Concrete Capping Cylindrical Concrete Specimens (A2LA Cert. No ) 09/05/2018 Page 2 of 4

3 Fireproofing: ASTM E605 1 ASTM E736 1 Masonry: ASTM C780 (Annex 6 Only) 1 ASTM C Tex-442-A Soils: ASTM D421 (Withdrawn 2016) 2 ASTM D422 (Withdrawn 2016) 2 ASTM D558 ASTM D698 ASTM D854 ASTM D1140 ASTM D1557 ASTM D1633 ASTM D1883 ASTM D2216 ASTM D2487 ASTM D ASTM D3282 ASTM D4318 ASTM D4718 ASTM D6913 ASTM D ASTM D7928 Tex-103-E Tex-104-E Tex-105-E Tex-106-E Tex-108-E Tex-110-E Tex-111-E Thickness and Density of Sprayed Fire-Resistive Material (SFRM) Applied to Structural Members Cohesion/Adhesion of Sprayed Fire-Resistive Materials Applied to Structural Members Preconstruction and Construction Evaluation of Mortars for Plain and Reinforced Unit Masonry Sampling and Testing Grout Determining Compressive Strength of Grouts Dry Preparation of Soil Samples for Particle-Size Analysis and Determination of Soil Constants Particle-Size Analysis of Soils Moisture-Density (Unit Weight) Relations of Soil-Cement Mixtures Laboratory Compaction Characteristics of Soil Using Standard Effort (12,400 ft-lbf/ft3 (600 kn-m/m3)) Specific Gravity of Soil Solids by Water Pycnometer Determining the Amount of Material Finer than 75-μm (No. 200) Sieve in Soils by Washing Laboratory Compaction Characteristics of Soil Using Modified Effort (56,000 ft-lbf/ft3 (2,700 kn-m/m3)) Compressive Strength of Molded Soil-Cement Cylinders CBR (California Bearing Ratio) of Laboratory-Compacted Soils Laboratory Determination of Water (Moisture) Content of Soil and Rock by Mass Classification of Soils for Engineering Purposes Classification of Soils for Engineering Purposes (Unified Soil Classification System) Description and Identification of Soils (Visual-Manual Procedures) Classification of Soils and Soil-Aggregate Mixtures for Highway Construction Purposes Liquid Limit, Plastic Limit, and Plasticity Index of Soils Unit Weight and Water Content for Soils Containing Oversize Particles Particle-Size Distribution (Gradation) of Soils Using Sieve Analysis In-Place Density and Water Content of Soil and Soil-Aggregate by Nuclear Methods (Shallow Depth) Standard Test Method for Particle-Size Distribution (Gradation) of Fine- Grained Soils Using the Sedimentation (Hydrometer) Analysis Determining Moisture Content in Soil Materials Determining Liquid Limits of Soils Determining Plastic Limit of Soils Calculating the Plasticity Index of Soils Determining the Specific Gravity of Soils Particle Size Analysis of Soils Determining the Amount of Material in Soils Finer than the 75 μm (No. 200) Sieve (A2LA Cert. No ) 09/05/2018 Page 3 of 4

4 Steel (Shop & Field) 1 : AWS D1.1 Structural Welding Code - Sheet Steel (Clause 6 Inspection, D1.2 Clause, Part 1 Inspection) AISC 360 Specification for Structural Steel Buildings (Chapter N, Section 16.1, N5, 6 QA/QC Fabrication & Erection) RCSC Specification for Structural Joints Using High-Strength Bolts (Section 9, Inspection) 1 This laboratory meets A2LA R104 General Requirements: Accreditation of Field Testing Laboratories for these tests. 2 This laboratory s scope contains withdrawn or superseded methods. As a clarifier, this indicates that the applicable method itself has been withdrawn or is now considered historical and not that the laboratory s accreditation for the method has been withdrawn. (A2LA Cert. No ) 09/05/2018 Page 4 of 4

5 Accredited Laboratory A2LA has accredited GORRONDONA ENGINEERING SERVICES, INC. Houston, TX for technical competence in the field of Construction Materials Testing This laboratory is accredited in accordance with the recognized International Standard ISO/IEC 17025:2005 General requirements for the competence of testing and calibration laboratories. This accreditation demonstrates technical competence for a defined scope and the operation of a laboratory quality management system (refer to joint ISO-ILAC-IAF Communiqué dated April 2017). Presented this 5 th day of September President and CEO For the Accreditation Council Certificate Number Valid to August 31, 2020 For the tests to which this accreditation applies, please refer to the laboratory s Construction Materials Scope of Accreditation.