SECTION PIBERGLAS REINFORCED PLASTIC PANELING

Transcription

1 SECTION PIBERGLAS REINFORCED PLASTIC PANELING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections, apply to this Section. 1.2 SUMMARY A. Section Includes: 1. Fiberglas Reinforced Plastic Paneling. 2. Miscellaneous Trims and Accessories. 1.3 ACTION SUBMITTALS A. Product Data: For each type of product. 1.4 PROJECT CONDITIONS A. Environmental Limitations: Do not deliver or install plastic paneling until spaces are enclosed and weathertight and temporary HVAC system is operating and maintaining ambient temperature and humidity conditions at occupancy levels during the remainder of the construction period. PART 2 - PRODUCTS 2.1 MANUFACTURERS A. Source Limitations: Obtain plastic paneling and trim accessories from single manufacturer. 2.2 PLASTIC SHEET PANELING A. Glass-Fiber-Reinforced Plastic Paneling: Gelcoat-finished, glass-fiber-reinforced plastic panels complying with ASTM D Panels shall be USDA accepted for incidental food contact.] 1. Manufacturers: Subject to compliance with requirements, [available manufacturers offering products that may be incorporated into the Work include, but are not limited to, the following: FIBERGLAS REINFORCED PLASTIC PANELING Project No

2 b. K%I~!~B...i;"~c~c1r1.irr:51...ftir:.. c. hxi2j.a nd... "!a.~i1.~.';.~...i!i2c:. 2. Surface-Burning Characteristics: As follows when tested by a qualified testing agency according to ASTM E 84. Identify products with appropriate markings of applicable testing agency. a. Flame-Spread Index: 25 or less. b. Smoke-Developed Index: 450 or less. 3. Nominal Thickness: Not less than 0.09 inch (2.3 mm) 4. Surface Finish: Molded pebble texture 5. Color: White 6. Basis-of-Desiqtr Product: CLalle Composites, Inc Glasboard Embossed Wall Panels - FXE - 4 ft by 8.9,10 & 10 R panels 2.3 ACCESSORIES A. Trim Accessories: Manufacturer's standard vinyl extrusions designed to retain and cover edges of panels. Provide division bars, inside comers, outside corners, and caps as needed to conceal edges. 1. Color: White. B. Exposed Fasteners: Nylon drive rivets recommended by panel manufacturer. C. Concealed Mounting Splines: Continuous, H-shaped aluminum extrusions designed to fit into grooves routed in edges of factory-laminated panels and to be fastened to substrate. D. Adhesive: As recommended by plastic paneling manufacturer and with a VOC content of 50 g/l or less. E. Sealant: Mildew-resistant, single-component, neutral-curing silicone sealant recommended by plastic paneling manufacturer and complying with requirements in Section "Joint Sealants." 1. Sealant shall have a VOC content of 250 g/l or less. PART 3 - EXECUTION 3.1 EXAMINATION A. Examine substrates and conditions, with Installer present, for compliance with requirements for installation tolerances and other conditions affecting performance of the Work. B. Proceed with installation only after unsatisfactory conditions have been corrected. FIBERGLAS REINFORCED PLASTIC PANELING Project No

3 3.2 PREPARATION A. Remove wallpaper,.vinyl wall covering, loose or soluble paint, and other materials that might interfere with adhesive bond. B. Prepare substrate by sanding high spots and filling low spots as needed to provide flat, even surface for panel installation. C. Clean substrates of substances that could impair adhesive bond, including oil, grease, dirt, and dust. D. Condition panels by unpacking and placing in installation space before installation according to manufacturer's written recommendations. E. Lay out paneling before installing. Locate panel joints so that trimmed panels at corners are not less than 12 inches (300 mnr) wide. 1. Mark plumb lines on substrate at trim accessory or panel joint locations for accurate installation. 2. Locate trim accessories or panel joints to allow clearance at panel edges according to manufacturer's written instructions. 3.3 INSTALLATION A. Install plastic paneling according to manufacturer's written instructions. B. Install panels in a full spread of adhesive. C. Install factory-laminated panels using concealed mounting splines in panel joints. D. Install trim accessories with adhesive and nails. Do not fasten through panels. E. Fill grooves in trim accessories with sealant before installing panels, and bed inside corner trim in a bead of sealant. F. Maintain uniform space between panels and wall fixtures. Fill space with sealant. G. Maintain uniform space between adjacent panels and between panels and floors, ceilings, and fixtures. Fill space with sealant. H. Remove excess sealant and smears as paneling is installed. Clean with solvent recommended by sealant manufacturer and then wipe with clean dry cloths until no residue remains. END OF SECTION FIBERGLAS REINFORCED PLASTIC PANELING Project No

4 THIS PAGE INTENTIONALLY LEFT BLANK

5 SECTION PENETRATION PIRESTOPPING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections, apply to this Section. 1.2 SUBMITTALS A. Product Data: For each type of product indicated. 1.3 QUALITY ASSURANCE A. Installer Qualifications: A firm that has been approved by FM Global according to FM Global 4991, "Approval of Firestop Contractors," or been evaluated by UL and found.to comply with its "Qualified Firestop Contractor Program Requirements." 1.4 PROJECT CONDITIONS A. Install and cure penetration firestopping per manufacturer's written instructions using natural means of ventilations or, where this is inadequate, forced-air circulation. 1.5 COORDINATION A. Coordinate construction of openings and penetrating items to ensure that penetration firestopping is installed according to specified requirements. B. Coordinate sizing of sleeves, openings, core-drilled holes, or cut openings to accommodate penetration firestopping. PART 2 - PRODUCTS 2.1 MANUFACTURERS A. Manufacturers: Provide products by one of the following available manufacturers: 1. AID Fire Protection Systems Inc. 2. Grace Construction Products. 3. Johns Manville. 4. 3M Fire Protection Products. 5. Tremco, Inc.; Tremco Fire Protection Systems Group. PENETRATION FIRESTOPPING Project No

6 6. Or approved equal. 2.2 PENETRATION FIRESTOPPING A. Provide penetration firestopping that is produced and installed to resist spread of fire according to requirements indicated, resist passage of smoke and other gases, and maintain original fireresistance rating of construction penetrated. Penetration firestopping systems shall be compatible with one another, with the substrates forming openings, and with penetrating items if any. PART 3 - EXECUTION 3.1 EXAMINATION A. Examine substrates and conditions, with Installer present, for compliance with requirements for opening configurations, penetrating items, substrates, and other conditions affecting performance of the Work. B. Proceed with installation only after unsatisfactory conditions have been corrected. 3.2 PREPARATION A. Surface Cleaning: Clean out openings immediately before installing penetration firestopping to comply with manufacturer's written instructions. 3.3 INSTALLATION A. General: Install penetration firestopping to comply with manufacturer's written installation instructions and published drawings for products and applications indicated. 3.4 FIELD QUALITY CONTROL A. Where deficiencies are found or penetration firestopping is damaged or removed because of testing, repair or replace penetration firestopping to comply with requirements. 3.5 CLEANING AND PROTECTION A. Clean off excess fill materials adjacent to openings as the Work progresses by methods and with cleaning materials that are approved in writing by penetration firestopping manufacturers and that do not damage materials in which openings occur. END OF SECTION PENETRATION FIRESTOPPING Project No

7 SECTION JOINT SEALANTS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections, apply to this Section. 1.2 SUMMARY A. Section Includes: 1. Silicone joint sealants. 2. Urethane joint sealants. 1.3 ACTION SUBMITTALS A. Product Data: For each joint-sealant product indicated. B. Samples for Initial Selection: Manufacturer's color charts consisting of strips of cured sealants showing the hll range of colors available for each product exposed to view. C. Joint-Sealant Schedule: Include the following information: 1. Joint-sealant application, joint location, and designation, 2. Joint-sealant manufacturer and product name. 3. Joint-sealant formulation. 4. Joint-sealant color. 1.4 INFORMATIONAL SUBMITTALS A. Product Certificates: For each kind of joint sealant and accessory, from manufacturer. B. Product Test Reports: Based on evaluation of comprehensive tests performed by a qualified testing agency, indicating that sealants comply with requirements. C. Preconstruction Compatibility and Adhesion Test Reports: From sealant manufacturer, indicating the following: 1. Materials forming joint substrates and joint-sealant backings have been tested for compatibility and adhesion with joint sealants. 2. Interpretation of test results and written recommendations for primers and substrate preparation needed for adhesion. D. Warranties: Sample of special warranties. JOINT SEALANTS Project No

8 1.5 QUALITY ASSURANCE A. Source Limitations: Obtain each kind of joint sealant from single source from single manufacturer. B. Moclups: Install sealant in mockups of assemblies specified in other Sections that are indicated to receive joint sealants specified in this Section. Use materials and installation methods specified in this Section. 1.6 PROJECT CONDITIONS A. Do not proceed with installation of joint sealants under the following conditions: 1. When ambient and substrate temperature conditions are outside limits permitted by jointsealant manufacturer[ or are below 40 deg F (5 deg C)]. 2. When joint substrates are wet. 3. Where joint widths are less than those allowed by joint-sealant manufacturer for applications indicated. 4. Where contaminants capable of interfering with adhesion have not yet been removed from joint substrates. 1.7 WARRANTY A. Special Installer's Warranty: Manufacturer's standard form in which Installer agrees to repair or replace joint sealants that do not comply with performance and other requirements specified in this Section within specified warranty period. 1. Warranty Period: Two years from date of Substantial Completion. B. Special Manufacturer's Warranty: Manufacturer's standard form in which joint-sealant manufacturer agrees to furnish joint sealants to repair or replace those that do not comply with performance and other requirements specified in this Section within specified warranty period. 1. Warranty Period: Five years from date of Substantial Completion. C. Special warranties specified in this article exclude deterioration or failure of joint sealants from the following: 1. Movement of the structure caused by structural settlement or errors attributable to design or construction resulting in stresses on the sealant exceeding sealant manufacturer's written specifications for sealant elongation and compression. 2. Disintegration ofjoint substrates from natural causes exceeding design specifications. 3. Mechanical damage caused by individuals, tools, or other outside agents. 4. Changes in sealant appearance caused by accumulation of dirt or other atmospheric contaminants. JOINT SEALANTS Project No

9 PART 2 - PRODUCTS 2.1 MATERIALS, GENERAL A. Compatibility: Provide joint sealants, backings, and other related materials that are compatible with one another and with joint substrates under conditions of service and application, as demonstrated by joint-sealant manufacturer, based on testing and field experience. B. Liquid-Applied Joint Sealants: Comply with ASTM C 920 and other requirements indicated for each liquid-applied joint sealant specified, including those referencing ASTM C 920 classifications for type, grade, class, and uses related to exposure and joint substrates. C. Stain-Test-Response Characteristics: Where sealants are specified to be nonstaining to porous substrates, provide products that have undergone testing according to ASTM C 1248 and have not stained porous joint substrates indicated for Project. D. Suitability for Contact with Food: Where sealants are indicated for joints that will come in repeated contact with food, provide products that comply with 21 CFR E. Colors of Exposed Joint Sealants: As selected by Architect from manufacturer's full range. 2.2 SILICONE JOINT SEALANTS A. Mildew-Resistant, Single-Component, Acid-Curing Silicone Joint Sealant: ASTM C 920, Type S, Grade NS, Class 25, for Use NT. 1. j"!:i?rh&_i: Subject to compliance with requirements, available products that may be incorporated into the Work include, but are not limited to, the following: a. IjiSI: Jj~j.iliidj.fli;-&i>Lk!~jj~y;Omniplus...' " b.!low l_i,rn1ijj;".'t>ri3ori1tio11; 786 Mildew Resistant. c. C'aP Advat~cixl h4;111:ri:1is - Silicones; Sanitary SCS1700. d. '~'~'c:~i.c~~~~c:j~~~~~~r~itc~i; Tremsil 200 Sanitary. 2.3 URETHANE JOINT SEALANTS A. Single-Component, Nonsag, Urethane Joint Sealant: ASTM C 920, Type S, Grade NS, Class 25, for Use NT 1. j~~~~iili-5: Subject to compliance with requirements, available products that may be incorporated into the Work include, but are not limited to, the following: a.!l3p;x::131.1 i Mi t:rg.$sy.b:te~j.~; Sonolastic NP 1 b. I3ost,iL ins.; Chem-Calk 900. c. j":~i!~;~ci~g,("j:i.i_rj.~?ri; Dynatrol I-XL. d. S.i&ii.-L~~~j:j~vc~j.ii~j~-i.~c>i~st ruct it) t~ 1~rotl1.1~1 s 13 i jz i s i on; Sikaflex - 1 a. e..~~'r~:i~cclli1~~~1:~~~~r~ii~~~~_i;vulkem116. JOINT SEALANTS Project No

10 B. Single-Component, Nonsag, Traffic-Grade, Urethane Joint Sealant: ASTM C 920. Type S, Grade NS, Class 25, for Use T. 1. I'"rcxii~i-ls: Subject to compliance with requirements, available products that may be incorporated into the Work include, but are not limited to, the following: a. LS,s?:..i3~ii i~li!ji1:~3y1.4~.~1~; Sonolastic NP1 b. $i Iw ~~~~:por~~tio~~~, C<>t~str~ic!.~~~j-k~rc~clt~cts llj~:&i<~j~; Sikaflex - 1 a. c. ' ; Vulkem JOINT SEALANT BACKING A. General: Provide sealant backings of material that are nonstaining; are compatible with joint substrates, sealants, primers, and other joint fillers; and are approved for applications indicated by sealant manufacturer based on field experience and laboratory testing. B. Cylindrical Sealant Backings: ASTM C 1330, as approved in writing by joint-sealant manufacturer for joint application indicated], and of size and density to control sealant depth and otherwise contribute to producing optimum sealant performance. C. Bond-Breaker Tape: Polyethylene tape or other plastic tape recommended by sealant manufacturer for preventing sealant from adhering to rigid, inflexible joint-filler materials or joint surfaces at back of joint. Provide self-adhesive tape where applicable. 2.5 MISCELLANEOUS MATERIALS A. Primer: Material recommended by joint-sealant manufacturer where required for adhesion of sealant to joint substrates indicated, as determined from preconstruction joint-sealant-substrate tests and field tests. B. Cleaners for Nonporous Surfaces: Chemical cleaners acceptable to manufacturers of sealants and sealant backing materials, free of oily residues or other substances capable of staining or harming joint substrates and adjacent nonporous surfaces in any way, and formulated to promote optimum adhesion of sealants to joint substrates. C. Masking Tape: Nonstaining, nonabsorbent material compatible with joint sealants and surfaces adjacent to joints. PART 3 - EXECUTION 3.1 EXAMINATION A. Examine joints indicated to receive joint sealants, with Installer present, for compliance with requirements for joint configuration, installation tolerances, and other conditions affecting jointsealant performance. B. Proceed with installation only after unsatisfactory conditions have been corrected. JOINT SEALANTS Project No

11 3.2 PREPARATION A. Surface Cleaning of Joints: Clean out joints immediately before installing joint sealants to comply with joint-sealant manufacturer's written instructions and the following requirements: 1. Remove all foreign material from joint substrates that could interfere with adhesion of joint sealant, including dust, paints (except for permanent, protective coatings tested and approved for sealant adhesion and compatibility by sealant manufacturer), old joint sealants, oil, grease, waterproofing, water repellents, water, surface dirt, and fiost. 2. Clean porous joint substrate surfaces by brushing, grinding, mechanical abrading, or a combination of these methods to produce a clean, sound substrate capable of developing optimum bond with joint sealants. Remove loose particles remaining after cleaning operations above by vacuuming or blowing out joints with oil-free compressed air. Porous joint substrates include the following: a. Plaster b. Gypsum Board c. Concrete. d. Masonry. e. Unglazed surfaces of ceramic tile. 3. Remove laitance and form-release agents from concrete. 4. Clean nonporous joint substrate surfaces with chemical cleaners or other means that do not stain, harm substrates, or leave residues capable of interfering with adhesion of joint sealants. Nonporous joint substrates include the following: a. Metal. b. Glass. c. Porcelain enamel. d. Glazed surfaces of ceramic tile. B. Joint Priming: Prime joint substrates where recommended by joint-sealant manufacturer or as indicated by preconstruction joint-sealant-substrate tests or prior experience. Apply primer to comply with joint-sealant manufacturer's written instructions. Confine primers to areas of jointsealant bond; do not allow spillage or migration onto adjoining surfaces. C. Masking Tape: Use masking tape where required to prevent contact of sealant or primer with adjoining surfaces that otherwise would be permanently stained or damaged by such contact or by cleaning methods required to remove sealant smears. Remove tape immediately after tooling without disturbing joint seal. 3.3 INSTALLATION OF JOINT SEALANTS A. General: Comply with joint-sealant manufacturer's written installation instructions for products and applications indicated, unless more stringent requirements apply. B. Sealant Installation Standard: Comply with recommendations in ASTM C 1193 for use of joint sealants as applicable to materials, applications, and conditions indicated. JOINT SEALANTS Project No

12 C. Install sealant backings of kind indicated to support sealants during application and at position required to produce cross-sectional shapes and depths of installed sealants relative to joint widths that allow optimum sealant movement capability. 1. Do not leave gaps between ends of sealant backings. 2. Do not stretch, twist, puncture, or tear sealant backings. 3. Remove absorbent sealant backings that have become wet before sealant application and replace them with dry materials. D. Install sealants using proven techniques that comply with the following and at the same time backings are installed: 1. Place sealants so they directly contact and fully wet joint substrates. 2. Completely fill recesses in each joint configuration. 3. Produce uniform, cross-sectional shapes and depths relative to joint widths that allow optimum sealant movement capability. E. Tooling of Nonsag Sealants: Immediately arer sealant application and before skinning or curing begins, tool sealants according to requirements specified in subparagraphs below to form smooth, uniform beads of configuration indicated; to eliminate air pockets; and to ensure contact and adhesion of sealant with sides of joint. 1. Remove excess sealant from surfaces adjacent to joints. 2. Use tooling agents that are approved in writing by sealant manufacturer and that do not discolor sealants or adjacent surfaces. 3. Provide concave joint profile per Figure 8A in ASTM C 1193, unless otherwise indicated. 4. Provide flush joint profile where indicated per Figure 8B in ASTM C CLEANING A. Clean off excess sealant or sealant smears adjacent to joints as the Work progresses by methods and with cleaning materials approved in writing by manufacturers of joint sealants and of products in which joints occur. 3.5 PROTECTION A. Protect joint sealants during and after curing period from contact with contaminating substances and from damage resulting from construction operations or other causes so sealants are without deterioration or damage at time of Substantial Completion. If, despite such protection, damage or deterioration occurs, cut out and remove damaged or deteriorated joint sealants immediately so installations with repaired areas are indistinguishable from original work. 3.6 JOINT-SEALANT SCHEDULE A. Joint-Sealant Application: Interior joints in horizontal traffic surfaces. 1. Joint Locations: JOINT SEALANTS Project No

13 a. Isolation joints in cast-in-place concrete slabs. b. Control and expansion joints in tile flooring. c. Other joints as indicated. 2. Silicone Joint Sealant: Single component, nonsag, traffic grade, neutral curing. 3. Urethane Joint Sealant: Single component, nonsag, traffic grade. 4. Joint-Sealant Color: As selected by Architect from manufacturer's full range of colors. B. Joint-Sealant Application: Interior joints in vertical surfaces and horizontal nontraffic surfaces. 1. Joint Locations: a. Control and expansion joints on exposed interior surfaces of exterior walls. b. Perimeter joints of exterior openings where indicated. c. Tile control and expansion joints. d. Vertical joints on exposed surfaces of walls and partitions. e. Perimeter joints between interior wall surfaces and frames of interior doors and windows. f. Joints between existing plaster walls and new gypsum board walls. g. Other joints as indicated. 2. Joint Sealant: [Latex] [Acrylic based] [Butyl rubber based]. 3. Joint-Sealant Color: As selected by Architect from manufacturer's full range of colors. END OF SECTION JOINT SEALANTS Project No

14 THIS PAGE INTENTIONALLY LEFT BLANK