*PRF8116* MATERIAL SAFETY DATA SHEET MIL-PRF-8116 PUTTY, GENERAL PURPOSE, NON-HARDENING 1. PRODUCT AND COMPANY INFORMATION

Transcription

1 MATERIAL SAFETY DATA SHEET *PRF8116* DATE ISSUED : 11/1/214 MSDS REF. No: PRF PRODUCT AND COMPANY INFORMATION PRODUCT NAME: Inventory ID: PRF8116 COMPANY INFORMATION 24 HR. EMERGENCY TELEPHONE NUMBER MACH-DYNAMICS (US Transportation): +1 (57) ext Main Street (International Transportation): +1 (57) ext. 4 Susquehanna, PA Phone: (57) Fax: (57) Contact: Mark Gingerella 2. HAZARDS IDENTIFICATION EMERGENCY OVERVIEW This material is not considered to be hazardous according to regulatory guidelines. NFPA CODES 3. COMPOSITION/CHEMICAL INFORMATION No reportable hazardous substances or complex substances. Page 1 of 5

2 4. FIRST AID MEASURES INGESTION: Do not induce vomiting. Seek medical attention. EYES: Flush immediately with water for at least 15 minutes Seek medical attention if irritation persist. SKIN: Remove contaminated clothing. Thoroughly wash with soap and large amounts of water. If irritation persist seek medical attention. INHALATION: Remove to fresh air. Seek medical attention. 5. FIRE FIGHTING MEASURES FLASH POINT ( F, TCC): Auto Ignition: LEL: UEL: EXTINGUISHING MEDIA: Water fog, foam, dry chemical, CO2. FIREFIGHTING INSTRUCTIONS: Use water spray to cool fire exposed surfaces. Use standard protective equipment. In enclosed spaces use a SCBA. FIRE AND EXPLOSION HAZARDS: Irritating gases may be present. 6. ACCIDENTAL RELEASE MEASURES GENERAL PROCEDURES: Avoid release into the environment. Contain spill, collect and transfer to suitable containers. Do not flush to sewer or allow to enter waterways. Recycle or dispose in accordance with federal, state and local regulations. 7. HANDLING AND STORAGE STORAGE TEMPERATURE: 72 F SHELF LIFE: Recommended use within 36 months from date of manufacture. HANDLING AND STORAGE PRECAUTIONS: Store in tightly closed properly vented container away from heat, sparks, open flame. COMMENTS: KEEP OUT OF REACH OF CHILDREN! Empty containers retain product residue and can be dangerous. Do not pressurize, cut weld, braze, solder, drill, grind, or expose such containers to heat, flame, sparks static electricity, or other sources of ignition. 8. EXPOSURE CONTROLS/PERSONAL PROTECTION EXPOSURE GUIDELINES: Page 2 of 5

3 ENGINEERING CONTROLS: Provide exhaust ventilation sufficient to keep the airborne concentration of this product below its exposure limits. Exhaust air may need to be cleaned by scrubbers or filters to reduce environmental contamination. PERSONAL PROTECTIVE EQUIPMENT EYES AND FACE: SKIN: Wear gloves when material is hot. RESPIRATORY: HYGIENIC WORK PRACTICES: Use good personal hygiene when handling this product. Wash hands after use, before eating, drinking, smoking, or using the toilet. OTHER USE PRECAUTIONS: Facilities storing or utilizing this material should be equipped with an eyewash facility and a safety shower. 9. PHYSICAL AND CHEMICAL PROPERTIES PHYSICAL STATE: Solid Chemical Type: Mixture ODOR: Slight Polysulfide Odor ph: BOILING POINT ( F): not determined FREEZING POINT: no data available VOLATILE ORGANIC COMPOUNDS: no data G/L (MVOC2 LBS/G) (VOC Theoretical As Packaged) % VOLATILE BY VOLUME: SOLUBILITY IN WATER: Insoluble EVAPORATION RATE (nbuacet=1): VAPOR DENSITY (AIR=1): SPECIFIC GRAVITY (water=1): 1.45 VAPOR PRESSURE (mm Hg): 1. STABILITY AND REACTIVITY STABLE: Yes HAZARDOUS POLYMERIZATION: Will not occur CONDITIONS TO AVOID: Strong oxidizing agents. HAZARDOUS DECOMPOSITION PRODUCTS: CO, CO 2, and various hydrocarbon fumes.. INCOMPATIBLE MATERIALS: Strong oxidizing agents. 11. TOXICOLOGICAL INFORMATION No data available Page 3 of 5

4 12. ECOLOGICAL INFORMATION No data available 13. DISPOSAL INFORMATION DISPOSAL METHOD: Any disposal practice must be in compliance with federal, state, and local regulations. Do not dump into sewers, ground, or any body of water. EMPTY CONTAINER: KEEP OUT OF REACH OF CHILDREN! Empty containers retain product residue and can be dangerous. Do not pressurize, cut weld, braze, solder, drill, grind, or expose such containers to heat, flame, sparks static electricity, or other sources of ignition. RCRA/EPA WASTE INFORMATION: Chemical waste generators must determine whether a discarded chemical is classified as a hazardous waste. US EPA guidelines for the classification determination are listed in 4 CFR. Additionally, waste generators must consult state and local hazardous waste regulations to ensure complete and accurate classification. 14. TRANSPORT INFORMATION DOT/IATA/IMO: Not Regulated *** MACH-DYNAMICS verifies that the material was supplied and shipped in the proper packages in accordance with DOT and federal regulations that are applicable to the mode of transportation selected. The shipper must verify that the packaging supplied is acceptable to be re-shipped in per the federal regulations applicable to the mode of transportation for reshipment. Regulations may change depending on mode of transportation selected.*** 15. REGULATORY INFORMATION When used for its intended purposes, this material is not classified as hazardous in accordance with OSHA 29 CFR This material contains no EPA class I Ozone Depleting Substances, hazardous materials in accordance with FED-STD-313, or any known carcinogens. 16. OTHER INFORMATION APPROVED BY: Mark Gingerella TITLE: President / QC Manager HMIS RATING Health: Flammability: Reactivity: Personal Protection: NFPA CODES DISCLAIMER: To the best of MACH-DYNAMICS knowledge, all information, recommendations, and suggestions appearing herein concerning this product are taken from sources or based upon data believed to be reliable. Although reasonable care has been taken in the preparation of this information, MACH-DYNAMICS extends no warranties or guarantees, express or implied, makes no representations and assumes no responsibility as to the accuracy, reliability or completeness of the information presented. MACH-DYNAMICS assumes no liability arising out of the use of the product by others. The conditions or methods of handling, storage, use and disposal of the product are beyond MACH-DYNAMICS control. The information provided herein may not be valid for this product if it is used in combination with any other materials or process. It is the user s responsibility to determine the suitability of the product, review the information provided herein, assess the safety and toxicity of the product and to comply with all applicable laws and regulations. For this and other reasons, MACH-DYNAMICS does not assume responsibility and expressly disclaims liability for any loss damage or expense arising out of or in any way connected with the handling, storage, use or disposal of the product. Page 4 of 5

5 Method Parameter Result RL Units 35B/61C Arsenic ND 1.9 mg/kg 35B/61C Barium mg/kg 35B/61C Cadmium mg/kg 35B/61C Chromium mg/kg 35B/61C Lead mg/kg 35B/61C Selenium ND 1.9 mg/kg 35B/61C Silver mg/kg 7471B Mercury ND.49 mg/kg 826C- Volatiles ND / Undetected ND Indicates that the analyte was not detected at the reporting limit RL Reporting Limit Test Analysis performed by EMSL Analytical, Inc., New Jersey, USA The sample was not miscible in methanol or water. Results may be biased. Page of 5