Technical Application Guide for UP-SHINE LED Pendant Linear

Transcription

1 Technical Application Guide for UP-SHINE LED Pendant Linear UP-DB8-4W

2 Introduction The design of batten realizes low cost, simple construction and superior capability, milky PC diffuser achieves anti-glare and high light transmittance. It is made of high lumen 835SMD led chip, energy saving, instant start, no flickering, no noise & UV/IR radiation, environmental friendly without Mercury or any other hazardous substances. It is a high efficient and low cost product with quite large potential market. Ideal replacement for various applications such as workshop, warehouse, exhibition hall, factory, shop, supermarket etc. Aluminum components generate a rust-free product for less maintenance Opal Acrylic Diffuser OSRAM Gear Up to 7% energy saving compared to standard CFL Environment friendly, without Mercury or any other hazardous substances Application notes IP for indoor use only The lamp must be installed by professional electrician Ensure the power supply is switched off before fitting this product Do not touch the lamp when in use Keep away from hot steam and corrosive gas Application Areas Widely used in office, meeting room, hotel, school etc. Certificate

3 Product Information Technical Specifications 58.5 Model Voltage Power Power Factor Lumen (±5%) Beam angle CCT Lifespan CRI Dimmable Dimension UP-DB8-4W AC-77V 4W o 3K 4h 8 No L5*W58.5*H58.5mm UP-DB8-4W AC-77V 4W o 4K 4h 8 No L5*W58.5*H58.5mm UP-DB8-4W AC-77V 4W o 5K 4h 8 No L5*W58.5*H58.5mm UP-DB8-4W AC-77V 4W.9 38 o 57K 4h 8 No L5*W58.5*H58.5mm Driver data Sheet Driver data Main Power Input rated Voltage Frequency Input Voltage AC-77V 5/6Hz AC9-35V Efficiency 88% No load wattage Total load Wattage W 4W±5% Power Factor.93 Rated input current 5A Full load output Voltage 6-75V Rated output current Output current range 56mA 56mA±5% Power tolerance ±5% Current output tolerance ±5% Short circuit protection Over voltage protection Over temperature protection PASS PASS PASS THD <% Withstand voltage AC5V Fixture Compatibility Rated Wattage Electrical Classification Ingress Protection Operating Temp Operating Humidity Storage Temp 4W Ⅰ IP - o C~45 o C ~9% - o C~65 o C

4 Spectral Distribution 3K 4K.8 Max=63 [.=] 4.8 SDCM F3K.8 Max=685 [.=] 3.4 SDCM F4K x=485 y=98 x=858 y= K 57K.8 Max=778 [.=] 5.38 SDCM F5K.8 Max=983 [.=].6 SDCM F57K x=539 y=745 x=3 y= Photometric Diagram 3K 4K MH=m C/8 C9/7 Flux out: 87 lm MH=m C/8 C9/7 Flux out: 9 lm AVERAGE BEAM ANGLE(5%): 5.9 DEG Height Eavg, Emax Angle: 5.9deg Diameter AVERAGE BEAM ANGLE(5%): 6. DEG Height Eavg, Emax Angle: 6.56deg Diameter 5K 57K MH=m C/8 C9/7 Flux out: 77 lm MH=m C/8 C9/7 Flux out: 8 lm AVERAGE BEAM ANGLE(5%): 6.6 DEG Height Eavg, Emax Angle: 8.84deg Diameter AVERAGE BEAM ANGLE(5%): 7. DEG Height Eavg, Emax Angle: 8.68deg Diameter

5 Polar Diagram Comparison -5 O 8 O 5 O O O O 9 O O 9 6 O -3 O 5 3 O O AVERAGE BEAM ANGLE (5%): 7.DEG C/8, 8. deg C3/,.6 deg C6/4,.7 deg C9/7, 6.7 deg Driver lifetime & LED light decay rate Driver Lifetime LED Light Decay Rate 9 % 4 Lifetime (hours) o C 75 o C 85 o C 95 o C 5 o C Capacitor Tc ( o C) % Luminous Flux 5% % 95% 9% 85% 8% 75% FLUX 5 U'V' 7% LifeTime (hours) Temperature The testing is operated at 5 C The lifetime of capacitor, minimum of 5, hours if operated at 5 C, will be doubled whenever the temperature drops C The highest withstand temperature of IC, MOS could be C The highest withstand temperature of LED junction temperature is 5 C 9 Temperature ( o C) :3:3 :3: :49: :7: :5: :43: 3:: 3:9: 3:37: Time 3:55: 4:3: 4:3: 4:49: 5:7: 5:43: 6:: 6:9: 6:37: IC Capacitor MOS PCB LED Fitting Environmental temperature The driver lifespan is based on capacitor working temperature.

6 Installation STEP STEP Open PC cover from lamp holder by flathead screwdriver. Remove the PC cover. 3 3 Separate PCB plate from lamp holder by flathead screwdrive. STEP 3 Open the packing and take out the lamp STEP Disconnect fast connector between lamp holder and PCB, then remove PCB from lamp holder. Knock plastic anchor into ceiling. Connect the male and female fast connector. L = BROWN N = BLUE = YELLOW-GREEN Connect L/N to terminal block. 3 3 Fasten lamp holder into ceiling with screw. Put the PCB plate back into lamp holder by pushing it upward directly, until it is attached to lamp holder tightly. STEP 5 STEP 6 OFF Pushing PC cover back to lamp holder by hands, until it is firmly fixed. Restore mains power and switch on for correct operation. ON

7 Installation STEP STEP Pried up the suspension hole by screwdriver. Pried up the terminal block on lamp holder. Open box and take out lamp with accessories. Connect L/N to terminal block. STEP 3 Hang fixture to ceiling with hanging wire. Packaging Information SIZE(CM) N.W/pc (KGS) G.W.(KGS) Q'TY(PCS) Carton 9.5*3*5.5 8 '' standard container 4'' standard container CTNS Q'TY(PCS) VOLUME(CBM) Phone: Add: nd building Dingfeng High-Tech Zone, Fuyuan st road, Fu Yong Sub-district, Bao'an, Shenzhen China