Thermal performance of buildings and materials Determination of specific airflow rate in buildings Tracer gas dilution method

Transcription

1 INTERNATIONAL STANDARD ISO Third edition Thermal performance of buildings and materials Determination of specific airflow rate in buildings Tracer gas dilution method Performance thermique des bâtiments et des matériaux Détermination du débit d'air spécifique dans les bâtiments Méthode de dilution de gaz traceurs Reference number ISO 12569:2017(E) ISO 2017

2 ISO 12569:2017(E) COPYRIGHT PROTECTED DOCUMENT ISO 2017, Published in Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISO s member body in the country of the requester. ISO copyright office Ch. de Blandonnet 8 CP 401 CH-1214 Vernier, Geneva, Switzerland Tel Fax copyright@iso.org ii ISO 2017 All rights reserved

3 ISO 12569:2017(E) Contents Page Foreword...v Introduction...vi 1 Scope Normative references Terms and definitions Measurement method and its selection General Concentration decay method Principle Two-point decay method Multipoint decay method Step-down exhaust concentration method Pulse method Continuous dose method Principle Average inverse concentration method Average concentration method Stationary concentration method Constant concentration method Type of tracer gas Measurement apparatus General Tracer gas dosing device Tracer gas sampling apparatus Gas analyser Procedure Building preparations Ancillary measurements Concentration decay method Calculation of two-point and multi-point methods Procedure of two-point and multi-point methods Calculation of step-down exhaust concentration method and pulse method Procedure of the step-down exhaust concentration method and pulse method Continuous dose methods Calculation of average of inverse concentration method Procedure of average of inverse concentration method Calculation of average concentration method Procedure of average concentration method Calculation of stationary concentration method Procedure of stationary concentration method Constant concentration method Calculation of constant concentration method Procedure of constant concentration method Accuracy General Tracer gas dose procedure and room concentration distribution Tracer gas sampling and storage method Tracer gas concentration measuring instruments General Resolution Tracer gas analyser drift Accuracy of tracer gas analyser...29 ISO 2017 All rights reserved iii

4 ISO 12569:2017(E) Calibration of tracer gas analyser Standard gas concentration Changes in outside wind and outdoor air temperature and schedule of air conditioning system Test report General Details necessary to identify the simulation tested Details of heating and ventilation systems Test conditions and apparatus Collected data and results Date of the test...32 Annex A (normative) Confidence intervals...33 Annex B (normative) Method to estimate ventilation rate Q v and effective mixed zone volume V emz simultaneously [3][4]...36 Annex C (informative) Considerations when measuring the ventilation rate of large spaces...41 Annex D (informative) Effects of internal and external temperature difference, temperature change, and outdoor air concentration change during the measurement period...42 Annex E (informative) Estimation error minimizing method in two-point and multi-point decay methods...46 Annex F (informative) Propagation of error analysis...51 Bibliography...53 iv ISO 2017 All rights reserved

5 ISO 12569:2017(E) Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement. For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISO's adherence to the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following URL: This document was prepared by Technical Committee ISO/TC 163, Thermal performance and energy use in the built environment, Subcommittee SC 1, Test and measurement methods. This third edition cancels and replaces the second edition (ISO 12569:2012), which has been technically revised. ISO 2017 All rights reserved v

6 ISO 12569:2017(E) Introduction The aim of ventilation is to maintain a proper hygienic status of the room by introducing outdoor air and diluting contaminants, heat, moisture or odour generated in the room, and evacuating them. In terms of energy savings, it is also important to keep the ventilation at the required rate, in order to reduce heat loss and heat gain under air conditioning as much as possible. Measurement of airflow rates is often necessary, for example, to check if the performance of a ventilation system is as intended, to assess the source strength of contaminants, to ensure that contaminants are properly eliminated, etc. The methods described here can be used to measure the ventilation rate or the specific airflow rate. vi ISO 2017 All rights reserved