Manual No Revision MODEL GLI HAND-HELD/PORTABLE TOTAL/FREE CHLORINE METER

Transcription

1 Manual No Revision MODEL GLI HAND-HELD/PORTABLE TOTAL/FREE CHLORINE METER

2 Please read this instruction manual carefully before using the instrument. This manual will provide you with all the necessary information for the correct use of the instrument. This meter is in compliance with European Community (CE) directives EN and EN TABLE OF CONTENTS PRELIMINARY EXAMINATION... 2 GENERAL DESCRIPTION... 2 SPECIFICATIONS OPTIONAL REAGENT ACCESSORIES... 3 DISPLAY CODE... 3 OPERATIONAL GUIDE TIPS FOR AN ACCURATE MEASUREMENT... 5 BATTERY REPLACEMENT... 5 WARRANTY... 5 GENERAL DESCRIPTION The meter measures the free and total chlorine (Cl 2 ) content in water and wastewater. The meter uses an exclusive positive-locking system to ensure that the cuvet is in the same place every time it is placed into the measurement cell. The reagents are in liquid form and are supplied in bottles. The amount of reagent is precisely dosed to ensure maximum repeatability. Display codes aid the user in routine operations. The meter has an auto-shut off feature that will turn the instrument off after 10 minutes of non-use. PRELIMINARY EXAMINATION SPECIFICATIONS Remove the instrument from the packing material and examine it carefully to make sure that no damage has occurred during shipping. If there is any damage, notify the transit carrier immediately. METER Each meter is supplied complete with: Two sample cuvets and caps One transport cap Instruction Manual One 9 Volt Battery NOTE: Save all packing material until you are sure that the instrument functions correctly. All defective items must be returned in their original packaging together with the supplied accessories. Model GLI Portable Chlorine Meter 2 Rev

3 Range Free Cl 2 Total Cl to 2.50 mg/l 0.00 to 3.50 mg/l Resolution Free Cl 2 Total Cl mg/l 0.01 mg/l C/68 F ± 0.03 mg/l; ± 3% of reading Typical EMC Deviation ± 0.01 mg/l Light Source 555 nanometers Light Detector Silicone photocell Measurement Method Adaption of EPA recommended DPD method The reaction between the chlorine and the DPD reagent causes a pink tint to appear in the sample. Operating Conditions From 0 to 50 C (32 to 122 F); max. 95% relative humidity Power Requirement One 9 volt battery; 40 hours continuous use; auto shut-off after 10 minutes of non-use Dimensions 7.1 x 3.3 x 1.8 inches (180 x 83 x 46 mm) Weight 10 oz. (290 g) OPTIONAL REAGENT ACCESSORIES The optional liquid reagent kit GLI T (for up to 300 tests of total/free chlorine) consists of: Part Number Unit Description Quantity GLI-93701A-T Total/free Cl 2 DPD1 indicator 3 drops GLI-93701B-T Total/free Cl 2 DPD1 buffer 3 drops GLI-93701C Total Cl 2 only DPD3 solution 1 drop DISPLAY CODE GUIDE This indicates that the meter is in a ready state and zeroing can be performed. Sampling in Progress. This prompt appears each time the meter is performing a measurement. This indicates that the meter is in a zeroed state and measurement can be performed. A zero reading was not taken. Insert a sample before adding reagent and press ZERO. Under range. A blinking "0.00" indicates that the sample absorbs less light than the zero reference. Check the procedure and make sure you use the same cuvet for reference (zero) and measurement. Over range. A flashing value higher than the maximum readable concentration (see SPECIFICATIONS) indicates that the sample absorbs too much light, meaning that the concentration is too high. Dilute the sample. Light over range. The cuvet is not inserted correctly and an excess ambient light is reaching the detector. If the cover is properly installed, then contact the GLI Customer Service Dept. Light under range. The zero sample is too dark for proper zeroing. If this is not the case, contact the GLI Customer Service Dept. The "V" indicates that the battery voltage is getting low and the battery needs to be replaced. This indicates that the battery is dead and must be replaced. NOTE: Once this indication is displayed, the meter will lockup. Change the battery to restart. Rev Model GLI Portable Chlorine Meter

4 OPERATIONAL GUIDE MEASUREMENT PROCEDURE 1. Turn the meter on by pressing ON/OFF. drops of DPD1 buffer ( Bottle B ) to the other cuvet. To measure Total Chlorine, also add 1 drop of DPD3 solution ( Bottle C ). Shake gently before adding 10 ml of unreacted sample from the first cuvet. Replace the cap and shake gently again. 2. When the LCD displays "- - -", it is ready. 3. Select free or total Chlorine by pressing FREE/TOTAL. In the lower right corner, an "I" will appear to indicate free chlorine or a "C" will appear to indicate total. 10. Reinsert the cuvet into the instrument. 4. Fill the cuvet with 10 ml of unreacted sample, up to the mark, and replace the cap. 5. Place the cuvet into the holder and ensure that the notch on the cap is positioned securely into the groove. 6. Press ZERO and "SIP" will appear on the display. 7. Wait for a few seconds and the display will show "-0.0-". Now the meter is zeroed and ready for measurement. 8. Remove the cuvet. 9. To measure Free Chlorine, add 3 drops of DPD1 indicator ( Bottle A ) and Wait for approximately 30 seconds and then press READ. The display will show "SIP" during measurement. The instrument directly displays concentration in mg/l of free or total chlorine. NOTE: Free and total chlorine have to be measured separately with fresh unreacted samples following the previously described procedure if both values are needed. INTERFERENCES Interference may be caused by: Bromine Iodine Fluorine Ozone Oxidized manganese Chromium Alkalinity above 250 mg/l or acidity above 150 mg/l will not reliably develop the full amount of color or it may rapidly fade. To re- Model GLI Portable Chlorine Meter 4 Rev

5 solve this, neutralize the sample with diluted HCl or NaOH. In case of water with hardness greater than 500 mg/l CaCO 3, shake the sample for about 1 minute after adding the reagent. TIPS FOR AN ACCURATE MEASUREMENT The tips listed below should be carefully followed during testing to ensure best accuracy: Do not touch the cuvet walls with hands. To maintain the same conditions during the zeroing and measuring phases, it is necessary to close the cuvet to prevent any contamination. Do not let test sample stand too long after reagent is added or accuracy will be lost. Whenever the cuvet is placed into the measurement cell, it must be completely free of fingerprints, oil or dirt. Wipe it thoroughly with a lint-free cloth prior to insertion. It is important that the sample does not contain any debris. This would corrupt the readings. It is possible to take multiple readings in a row, but it is recommended that a zero reading be taken for each sample and that the same cuvet is used for zeroing and measurement. It is important to discard the sample immediately after the reading is taken because the glass might become permanently stained. Shaking the cuvet can generate bubbles in the sample, causing higher readings. To obtain accurate measurements, remove such bubbles by swirling or by gently tapping the vial. All the reaction times reported in this manual are referred to 20 C (68 F). As a general rule, they should be doubled at 10 C (50 F) and halved at 30 C (86 F). BATTERY REPLACEMENT When the battery is low, "BA" is displayed to indicate that it must be replaced. Battery replacement must only take place in a non-hazardous area. To replace a run-down battery, simply remove the battery compartment cover on the rear of the meter and replace the battery, observing correct polarity. WARRANTY GLI International, Inc. warrants the Model GLI Hand-held/Portable Chlorine Meter to be free from defects in material or workmanship for a period of one year (12 months) from the date of shipment of this product from our facility. A warranty claim will not be honored if defects are not reported within the warranty period, or if GLI International determines that defects or damages are due to normal wear, misapplication, lack of maintenance, abuse, improper installation, alteration or abnormal conditions. GLI International s obligation under this warranty shall be limited to, at its option, replacement or repair of this product. The product must be returned to GLI International, freight prepaid, for examination. The product must be thoroughly cleaned and any process chemicals removed before it will be accepted for replacement or repair. GLI International s liability shall not exceed the cost of the product. Under no circumstances will GLI International be liable for any incidental or consequential damages, whether to person or property. GLI International will not be liable for any other loss, damage or expense of any kind, including loss of profits, resulting from the installation, use, or inability to use this product. Rev Model GLI Portable Chlorine Meter