OWNER S MANUAL DIRECT-IT PRODUCTS. October 2006

Transcription

1 OWNER S MANUAL DIRECT-IT PRODUCTS October 2006 Injectidry Systems, Inc. Phone: Fax: Toll Free:

2

3 THE DIRECT-IT (UAA2) USAGE The newly designed Direct-It, now works with axial fans, air scrubbers or other collared drying devices that fit duct ring sizes of 12, 14, 16 & 18. The adapter can be attached to dry either positively or negatively. The back of the Direct-It resembles a set of stair steps, and will simply slip into the correct size opening of your drying equipment. READ BEFORE OPERATING or ATTACHING THE ADAPTER SERIOUS PHYSICAL INJURY CAN RESULT FROM FAILURE TO FOLLOW THESE INSTRUCTIONS: 1. Wear protective eyewear such as safety glasses when stretching, fastening or releasing hooks. 2. Do not stretch cord more than 50%. (Example 12 to max 18 ). Cords can be stretched more than 50%, but could cause failure of cord or hook & result in serious eye or other injury. 3. Inspect cord before use. Do not use if cord is frayed or hooks are bent or damaged. 4. Cord acts like a rubber band. Do not stretch cord toward or away from you to avoid being struck by hooks. Pull to one side and keep your face and body away from rebound path. HOW TO ATTACH THE DIRECT-IT (UAA2) BUNGEE CORD - The bungee cord allows for the greatest range of movement. Grasp both ends of the cord (the hooks) and pull on them to equalize the cord length on both sides of equipment. Now, extend cord around smaller drying equipment such as axial fans and attach the end hooks to other side of shroud. For attaching to larger drying equipment, pull only on one end of the bungee cord (hook) and then extend cord to accommodate longer odd shaped products. Page 1 of 6

4 HOW TO ATTACH THE DIRECT-IT (UAA2) Step 1. Place the Direct-It in front of the airmoving device to be used (as shown in picture below). Step 2. Insert the Direct-It housing into the ring of the chosen airmoving device.. Step 3. While holding the Direct-It housing, carefully stretch the lower bungee cord around the base of the airmoving device and fasten the cord hook. Step 4. Repeat Step 3. Step 5. We recommend placing the Direct-It and airmoving device in the center of the run to be dried. The hosecuffed ends of the supplied hoses may now be installed on the Direct-It. SIMPLE TO INSTALL * See warning on previous page Page 2 of 6

5 INSTALLATION OF DIRECT-IT It is recommended that the drying device be set up at the center of the drying run. Install in a safe manner. Keep aisles clear and always reduce any unnecessary trip hazards. Set up warnings if trip hazard exists. The Direct-It comes with the following parts: 01 - UAA2 (bungee cord attached) 03-1 ¼ inch Hoses (3 sections of 1 1/4 inch x 50 feet hose) 17-5/8 Wall Penetrators (bagged) /4 Hose Cuffs 01 - CB1 Carry Bag 5/8 WALL PENETRATOR *Redesigned* This part is black in color. It will slide into the end of the 1 1/4 hose or into a 1 1/4 Hose Cuff. The business end of the Penetrator is 5/8. DRILLING HOLES We HIGHLY RECOMMEND using an adjustable drill stop. The depth of drill penetration will be based upon the thickness of material being drilled. The drill should be stopped from penetrating hidden wall components such as electrical wires or plumbing pipes. Use a 11/16 Paddle bit for the 5/8 Wall Penetrator. SUGGESTED HOSE LENGTHS The hose is shipped blank, allowing the technician the freedom to choose whatever lengths make the most sense. Be cautious when cutting the hose with sharp instruments. Always cut away from yourself and not towards anything that you aren t willing to cut - if your hand were to slip.. Put the hose on a surface such as plywood or OSB to avoid damaging surfaces beneath the hose. Extra hoses sections are available for purchase (Item # PL05). CONTAMINATION On all restoration jobs, moving air can disturb dust and particulates. Air filtration devices (AFD's) should be used to control dust, debris and possible mold. Page 3 of 6

6 Page 4 of 6

7 Wall Drying Stair Drying Cabinet Drying Abatement Technologies Air Scrubber When drying negatively using an airscrubber such as pictured above, the Direct-It may be positioned on top without bungee cord attachment. Page 5 of 6

8 WARRANTY DIRECT-IT / DIRECT-IT IN - 1 Year Limitations: This warranty will not extend to Injectidry products showing any accidental damage, alteration, normal wear, disassembly, lack of proper maintenance, damage from fire or flood, damage from corrosive or other chemicals, improper voltage use, unauthorized repairs, use of non-genuine parts and materials, misuse, or any other causes beyond the control of Injectidry. The warranty obligation extends only to the repairs or replacement of parts found to be defective upon the examination and the decision of Injectidry Systems. The preceding limitations constitute the entire warranty. No other warranty or responsibility is expressed or implied. The warranty includes legal rights to the original purchaser, and additional rights may be available, varying state to state. In addition, Injectidry Systems Repair Department must authorize all incoming products and/or repair work to be completed by an authorized repair center. Injectidry Systems is not responsible for any repairs or modifications to any of its products, unless completed by Injectidry Systems or an authorized service center. We are not responsible for subsequent damaged caused by the user and or its agents. CUSTOMER SERVICE Please call one of our customer service representatives for technical support or to order parts. It is our number one priority to take care of your needs in a fast and courteous fashion. Incomplete Shipments All shortages must be reported within five business days. Be sure to check the number of cartons or packages. Compare this count with the total listed on Bill of Lading and confirm that all cartons or packages pertaining to this shipment have been received. If quantities do not match, have the delivery driver note shortage. If the missing cartons or packages do not show up in the next few days, contact the Shipping Department and we can reship on a new order. You must file a Freight Claim for shorted packages if the count differs from the Bill of Lading. For your protection, the carrier which delivers merchandise to your door is responsible for any loss or damages. Acceptance of the shipment by the carrier company is acknowledgement that the articles delivered to them were in good condition and properly packaged. Freight Damage Orders are shipped Freight on Board (F.O.B.) from our warehouse in Lynnwood, WA. Once the product has shipped to the customer, it is the customer s responsibility. We will assist the customer in filing for any freight damage claims but these claims must be filed by the recipient. We suggest that the shipment be inspected carefully upon receipt. If there is visible damage, note this on the waybill before you sign and you must notify the carrier immediately. We want to know if there are any freight damages, so please contact our shipping department right away. CONTACT US Our phone number: Our fax number: Our toll free number in the U.S. and Canada: On the Web at: Page 6 of 6