Transcription

1

2 The Erdman 3M VHB Structural Glazing Tape Applicator, Frame Assembly & Glass Lay-in System Erdman 3M VHB Structural Glazing Tape Applicator, Frame Assembly and Glass Lay-in System Erdman 3M VHB Structural Glazing Tape Applicator, Frame Assembly, Glass Lay-in System, with Bridge Manipulator 1 Phone:

3 Erdman Automated Linear Tape Applicator Capacity: (4) Aluminum extrusion profiles, each up to 16 ft. long Operator manually loads and unloads the aluminum extrusion profiles on the machine Automatic X & Y coordinate travel Automatic compressed air blow off of loose contaminates on extruded product Automatic cleaning solvent applicator, with low solvent auto sensing alarm Automatic primer applicator, with low solvent auto sensing alarm Automatic tape applicator with straight cut capability and low tape auto shutoff sensor Adjustable pressure sensitive roller provides verification of applied pressure as defined by 3M requirements, assuring a proper bond of the adhesive tape to the aluminum Steel mesh safety guarding mounted on the rear and both ends of the machine. Safety light curtain mounted on the front (operator area) of the machine Equipment will be configured to meet your specifications Phone:

4 Erdman Hand Assisted Manual Linear Tape Applicator Capacity: (1) Aluminum extrusion profile up to 16 ft. long Hand Assisted X axis (right to left) controlled travel of the tape dispensing head Aluminum extrusion profiles must be manually cleaned and primed prior to sealant tape application Operator manually loads and unloads the aluminum extrusion profiles on the machine Once the part is manually cleaned, primed and loaded, the operator will control the tape application head and manually roll the tape carriage across the aluminum extrusion, sequencing all functions with the hand control Adjustable pressure sensitive roller provides verification of applied pressure as defined by 3M requirements, assuring a proper bond of the adhesive tape to the aluminum Standard 240v (480v optional) Custom Equipment and Options Available 3 Phone:

5 Erdman Conveyor The Erdman Eacy Conveyor is a complete system including motors controls, sensors and/or feed back devices as required for your application. We offer a wide variety of non-marking, non-stick belts and/or rollers. The Eacy Conveyor is built to handle your toughest or most delicate applications. Conveying speeds from 10 to 600 FPM, fixed or variable. 90 degree transfers, 180 degree in-line flip over, product diverters and product queuing stops are some of the available options. Custom equipment and options are available! Phone:

6 Erdman Semi-Automated Frame Assembly Clamp Unit capacity: 6 ft. x 12 ft. Frames (overall outside dimension) PLC controlled; operator to select frame size and fastening pattern Non-marring work surfaces Two work surfaces sized accordingly to support vertical side components and mull posts One work surface position is fixed and the other work surface is adjustable. Stationary stop fence on fixed side and stop blocks at the beginning end. Operator to position product components to stationary fence and end stop blocks Adjustable work surface side clamps in one direction, towards operator (1) Screw Feeder, supplying (2) machine mounted Screw Guns 5 Phone: Screw Guns mounted on THK rails to the long sides of the Frame Assembly Clamp Operator is responsible for manually positioning the Screw Guns, utilizing the Laser Pointer for locating the hole centers Operator pushes a button to actuate clamping of mull post component, centering it into fastening position. Once clamped, the Screw Gun, controlled by a servo, will auto index and drive screws Initial estimated clamping and (4) screw drilling sequence time: seconds AB Opto-Touch dual hand push button anti-tie down start for operator safety Electrical Utilities: standard 110 VAC Equipment will be configured to meet your specifications

7 Erdman 6 ft. x 12 ft. Glass Lay-in Station Maximum Capacity: 6ft. wide x 12ft. long frames Non-powered roller bed top; manual load and unload of product Urethane coated rollers on 9 centers. Bed height: (TBD) Stationary front guide fence Retractable squaring end stops (12) Beams with (5) Lift Pins mounted on each beam Complete set of lift pins shift 6, front to back, to provide clearance for the frame vertical side rails Manual override capability of pin positioning, to avoid the vertical frame rail when solid panels exist (12) Lift pin rows can shift independently 6, right to left, providing clearance for the horizontal frame components Hydraulic lift package Two-stage drop, with foot or hand switch for lowering First stage lowers glass inside frame, just above sealant or adhesive tape, allowing for final glass alignment and setting blockplacement Second stage sets glass in its finished position The Glass Lay-in Station provides the ability to place single or multiple lights at one time, with the capability to manually disable individual rows of lift pins, allowing the placement of specific lights into the frames Standard 240 VAC (480 VAC Optional) Equipment will be configured to meet your specifications Phone:

8 7 Phone: Erdman Tip Table Eliminate lifting and significantly reduces the potential of back injuries Gently handles your product, no dents, scratches or marks! Hydraulically driven and electronically controlled Worldwide recognized hardware and controls Little or no special maintenance required Custom Equipment and Options are Available!

9 Erdman 6ft. x 12ft. Hand Assisted Glass Roll Press Station Maximum Capacity: 6ft. wide x 12ft. long frames Operator manually loads and unloads the window units on the machine Hand assisted X & Y coordinate travel Once the window unit is loaded, the operator will manually traverse the roll press across the glass, sequencing all functions of the roll press head with the hand control Adjustable pressure sensitive roller provides verification of applied pressure as defined by 3M requirements, assuring a proper bond of the glass to the adhesive tape Standard 240v (see options for 480v) Equipment will be configured to meet your specifications Phone:

10 External Weather/Cap/Heel Bead Sealant Applicator The Erdman sealant applicator can be used for curtain wall and interior glass partition applications. A servo control system, it uses Erdman s fluid metering technologies to provide a consistent diameter bead of sealant at speeds up to 30 per second. Hot, cold or two-part sealant dispensing is available. It can be set for bead sizes from in diameter. Custom models, configurations and sizes are available. The equipment will be configured to meet your specifications 72 Depth by 144 Width glazing area (light opening) 32 to top of rollers (or matched to bed height of existing equipment) Eacy Slide, PVC covered steel rollers Heavy Duty hose hanger assembly Hoses for single-part ambient sealant LED Light-Kit Z Axis Floating Head (Air/oil included) Standard 240v (see options for 480v) 9 Phone:

11 Equipment will be configured to meet your specifications Enables the operator to perform controlled precise movement and placement of glass Increase operator safety & reduces product damage Weight capacity: 500# Dimension 34 x 50 (can be customized for your facility) 36 vertical travel Dial regulator to adjust for different weights Handle bar to keep controls at comfortable height and operator at a safe distance from glass. Erdman Bridge Manipulator Automatically pivots along with glass 90 PSI air supply Four 10 diameter cups Venturi style vacuum pumps w/ blow off and VacTrap to prevent glass from dropping in event of lost air supply The four cups can be arranged in a straight line for long, narrow glass Must achieve desired vacuum level before manipulator will lift. Pneumatic powered 90-degree tilt Squaring capability on end effectors Phone:

12 Discover the Erdman Line of Equipment Visit our website: for more products and services Erdman Automated Chop Saw Erdman EacyClamp Erdman Bridge Manipulator Erdman 7000 Series IG Sealer Erdman Tilt Table Erdman Screw Feeder Erdman Hand Assist Glazer Erdman Manipulator Arm MORGAN DONOHUE V.P. Sales and Marketing JEFF AUMOCK Sales DALE HATCH Design Supervisor JIM TIBESAR Sales Manager PAUL VAN KEMPEN General Manager LARRY BERNING Controls Engineer Supervisor CHAD HEITSCHMIDT Sales JESSICA ERDMAN Marketing Manager JOLENE ERDMAN Project Coordinator 1603 South 14th Street Princeton, MN Phone: Fax: