University of Florida Rocket Team Preliminary Design Review
|
|
- Tyrone Williams
- 6 years ago
- Views:
Transcription
1 University of Florida Rocket Team Preliminary Design Review
2 Agenda Overview Mission Statement Concept of Operations Summary Vehicle Subsystems Motor Choice Flight Dynamics and Simulations Payloads Target Detection Project Plan Verification Safety Verification Educational Engagements Budget and Funding Schedule Future Work
3 Mission Statement The UF Rocket Team will develop a payload that will be flown to an altitude of 5,280 feet. All components will be safely recovered after each flight. By doing so the team hopes to gain experience in a research-based, competitive, and experiential exploration project while also providing relevant and cost effective research and development. During the process, the UF Rocket Team will focus on developing an interest in STEM fields and STEM education in the local area.
4 Concept of Operations The launch vehicle shall reach a target apogee altitude of 5,280 ft. At apogee, the launch vehicle shall separate and release the target detection payload. At apogee, both the launch vehicle and payload will release parachutes (drogue for launch vehicle, singular parachute for payload). The launch vehicle and the target detection payload shall not follow a ballistic trajectory.
5 Concept of Operations The target detection camera shall observe the area beneath the launch vehicle and analyze it to determine the color of the tarps. At an altitude of 600 ft. the launch vehicle will again separate and release the main parachute; it will land using this parachute. The launch vehicle and payload shall transmit its location to the ground station via GPS.
6 Agenda Overview Mission Statement Concept of Operations Summary Vehicle Subsystems Motor Choice Flight Dynamics and Simulations Payloads Target Detection Project Plan Verification Safety Verification Educational Engagements Budget and Funding Schedule Future Work
7 Component Overview
8 Dimensions, Materials and Justification Airframes G12 Fiberglass Yield Strength: 41 ksi Bulkheads/Centering Rings Type 2 PVC Shear Modulus: 145 ksi Nosecone Polypropylene Plastic Weight: 10.5 oz Total Length 102 inches Total Weight lbs
9 Forward Section Dimensions Body Tube: 15.0 in. OD: in. ID: in. Coupler: 12.0 in. OD: in. ID: in. Purpose 1. Aerodynamics 2. Houses payload 3. Contains payload drogue
10 Avionics Bay Dimensions Body Tube: 17.5 in. OD: in. ID: in. Coupler: 10.0 in. OD: in. ID: in. Purpose 1. Ejection charges 2. Houses Avionics Bay 3. Contains drogue chute
11 Aft Section Dimensions Body Tube: 49.4 in. OD: in. ID: 3.90 in. Inner Tube: 24.0 in. OD: in. ID: in. Motor Centering 2 centering rings, 1 in. thick each Motor Retention Screw-on engine retainer Fin Integration Through-the-wall fin attachment
12 Composite Fins Fin Manufacturing Wet Layup Process CNC Milled Aluminum Molds Parchment Paper Mold Release C-clamp Compression E-class Fiberglass Added for Mass at Reduced Cost Carbon Fiber/fiberglass 45 and 90 weave orientations
13 Avionics and Recovery Avionics Electronics PerfectFlite Stratologger CF x2 BigRedBee BRB900 GPS Ejection Charges 2 Grams Black Powder Deployment Scheme Apogee - 36 Drogue Housed in mid fuselage 600 Feet - 48 Main Housed in aft fuselage
14 Avionics and Recovery
15 Motor Selection Motor Selection: Cesaroni K635-RL-17 Chosen based on a plethora of decision criteria, including thrust curve performance, total impulse, max thrust, and burn time. TOTAL IMPULSE: MAX THRUST: AVERAGE THRUST: ISP: BURN TIME: PROPELLANT MASS: DRY MASS: TOTAL MASS: MOTOR DIAMETER: Ns ( lb.s) N ( lb) N ( lb) s s 1115 g (39.33 oz) 649 g (22.89 oz) 1768 g (62.35 oz) 54 mm (2.13 in)
16 Propulsion System & Motor Selection
17 Flight Dynamics and Simulation The simulations were run in OpenRocket, a 6 degree of freedom software used to predict rocket flight. The simulations were run using flight conditions predicted for the month of April in Huntsville, Alabama. Simulations were run to predict: Apogee Velocity Acceleration Stability Margin
18 Velocity vs. Time
19 Acceleration vs. Time
20 Stability Margin Static Stability Margin: SM =(Xcp-Xcg)/d 3.47 Higher static stability margin to ensure stability during the beginning of flight Stability margin of 2.12 off the rod
21 Drift Radius
22 Kinetic Energy Kinetic energy During Descent: Main parachute: lbm*ft 2 /s 2 Drogue parachute: lbm*ft 2 /s 2 Calculated using the average velocity between time when parachute was employed and the time the rocket touched the ground.
23 Agenda Overview Mission Statement Concept of Operations Summary Vehicle Subsystems Motor Choice Flight Dynamics and Simulations Payloads Target Detection Project Plan Verification Safety Verification Educational Engagements Budget and Funding Schedule Future Work
24 Payload Summary Payload subsystem will be ejected at apogee. Payload subsystem will use one 12 parachute for recovery. There will be a primary and redundant altimeter for recovery. A raspberry pi zero will process the images.
25 Alternative Designs
26 Payload Electronics
27 Camera Slot
28 Payload Dimensions
29 Payload Wiring
30 Agenda Overview Mission Statement Concept of Operations Summary Vehicle Subsystems Motor Choice Flight Dynamics and Simulations Payloads Target Detection Project Plan Verification Safety Verification Educational Engagements Budget and Funding Schedule Future Work
31 Verification and Test Plan Subsystem Tests Requirements Payloads Target Detection Test Structures Airframe Material Test Avionics Bay Material Test Drop Test Recovery Charge Ejection Test Parachute Packing Test Ground Main and Drogue Deployment Test
32 Verification and Test Plan Subsystem Tests Requirements Avionics Transmission Test Battery Life Check GPS Range Test Propulsion Static Motor Test Full Scale Launch Subscale Launch Aerodynamics Subscale Wind Tunnel Test Boattail Wind Tunnel Test Miscellaneous Subscale Launch Launch Rehearsal Full Scale Launch
33 Safety Verification Each team shall use a launch and safety checklist created by the team. The safety officer will attend team activities to monitor, emphasize safety and develop hazard analyses, failure modes analyses, and procedures. The team mentor, Jimmy Yawn, will be also be responsible for team safety during any processes that require his involvement. A Launch Operations Risk, Hazards Analysis, Failure Modes, and Vehicle Environmental Concerns assessments have been carried out to emphasize the criticality of potential occurrences that would affect the team s safety or the safety of the surrounding environment and how to best to handle them.
34 Safety Verification Cont. The UF Rocket Team will conduct a majority of all manufacturing, composites, propulsion, and testing work at the UF MAE Student Design Center (SDC) in the Rocket Team bay. All members will abide by the rules of the MAE SDC and safety protocol are obeyed. ensure all Qualified members of the UF Rocket Team will be given tests to become certified as Safety Stewards, if desired, which gives them access to all machines and equipment in the SDC. Safety Stewards have a list of responsibilities that they must follow when conducting work in the SDC. All members that are not certified as Safety Stewards must perform all activities with the guidance of a Safety Steward.
35 Educational Engagement Engagement at local schools Engaging Presentation on STEM geared toward Rocketry Live rocket launch demonstrations, hands-on kits and activities Coordination with Alachua County Public Schools Volunteer Office 3 Elementary School Events Station based hands-on activities
36 Budget and Funding
37 Schedule Event Dates Subscale Work 11/6 12/6 Subscale Launch 12/9 Final Material Ordered 1/1 Full Scale Manufacturing 1/8 2/8 Full Scale Launch 2/10
38 Agenda Overview Mission Statement Concept of Operations Summary Vehicle Design Methodology Subsystems Motor Choice Flight Dynamics and Simulations Vehicle Verifications Plan Payloads Target Detection Project Plan Verification Safety Verification Educational Engagements Budget and Funding Schedule Future Work
39 Future Work Develop detailed, final design Manufacture subscale Component Testing Order all materials Subscale Launch, Dec. 9th
40 Questions
NU HOPE. Northeastern University. High-altitude Object Protection Experiment
NU HOPE Northeastern University High-altitude Object Protection Experiment Agenda Overview of Vehicle Properties Stability Analysis Launch Vehicle Sections and Systems Booster Stage Interstage system Payload
More informationUC Berkeley Space Technologies and Rocketry Post Launch Assessment Review Project U.R.S.A. 1
UC Berkeley Space Technologies and Rocketry Post Launch Assessment Review Project U.R.S.A. 1 April 24, 2017 1 Upright Recovery and Sight Acquisition Contents 1 Flight Results 2 1.1 Motor Used........................................
More informationCAR High Power Rocket. Level 4 Certification Process
Canadian Association of Rocketry Level 4 Certification Process CAR High Power Rocket Level 4 Certification Process Version: 1.61 - Updated: September 20, 2009 Page 1 of 13 Contents 1. Introduction... 3
More informationFlight Readiness Review
Flight Readiness Review 2012-2013 NASA USLI We can lick gravity, but sometimes the paperwork is overwhelming. - Werner Von Braun [Type text] I) Summary of FFR Report [Type text] i Note to reader: To facilitate
More informationNASA Student Launch Preliminary Design Review
2016-2017 NASA Student Launch Preliminary Design Review Institution: Mailing Address: Project Title: United States Naval Academy Aerospace Engineering Department United States Naval Academy ATTN: NASA
More informationrocket s apogee. When this ejection occurs, the balloon and canister will no longer be
4.0 Drogue Chute The balloon and electronics canister will be ejected from the balloon near the rocket s apogee. When this ejection occurs, the balloon and canister will no longer be attached to the rocket
More informationSOFT RECOVERY SYSTEMS FOR GUN- FIRED PROJECTILE COMPONENTS
SOFT RECOVERY SYSTEMS FOR GUN- FIRED PROJECTILE COMPONENTS Item Type text; Proceedings Authors Fritch, Paul L.; Spinelli, Carmine J. Publisher International Foundation for Telemetering Journal International
More informationNASA Student Launch Proposal
2016-2017 NASA Student Launch Proposal Institution: Mailing Address: Project Title: Date: Competition: United States Naval Academy Aerospace Engineering Department United States Naval Academy ATTN: NASA
More informationDesign of a High-g Unmanned Aerial Vehicle Structure
Design of a High-g Unmanned Aerial Vehicle Structure Seth S. Kessler, S. Mark Spearing and Greg A. Kirkos TECHNOLOGY LABORATORY FOR ADVANCED COMPOSITES Department of Aeronautics and Astronautics Massachusetts
More informationPublic Missiles, Ltd.
Copyright 2008 by Public Missiles, Ltd. All rights reserved Copilot2_Instructions_Ver1_6.Doc 1 Public Missiles, Ltd. Co-Pilot v2.0 Dual-Deployment Recovery Altimeter Public Missiles, Ltd. 6030 Paver Lane,
More informationCanSat Competition Guide Mission: Mars Glider
CanSat Competition Guide 2016 Mission: Mars Glider Rev 1.1 Sept 18, 2015 1 Table of Contents 1. Introduction...4 1.1 Competition Description...4 2. Mission Overview...5 3. Requirements...7 3.1 Base Requirements...7
More informationCOOLING TECHNOLOGY INSTITUTE
PAPER NO: TP08-16 CATEGORY: DRY COOLING COOLING TECHNOLOGY INSTITUTE THE COST OF NOISE ROBERT GIAMMARUTI HUDSON PRODUCTS CORPORATION JESS SEAWELL COMPOSITE COOLING SOLUTIONS, LLC The studies and conclusions
More informationPneumatic Mortar Development for the NASA/Orion Capsule Drogue Parachute System
21st AIAA Aerodynamic Decelerator Systems Technology Conference and Seminar 23-26 May 2011, Dublin, Ireland AIAA 2011-2598 Pneumatic Mortar Development for the NASA/Orion Capsule Drogue Parachute System
More informationDATA ITEM DESCRIPTION
DATA ITEM DESCRIPTION Title: Test Plans/Test Procedures Number: DI-SESS-81704 Approval Date: 20061122 AMSC Number: F7658 Limitation: N/A DTIC Applicable: N/A GIDEP Applicable: N/A Preparing Activity: 10
More informationCustom Small UAV Lab. To: Dr. Lewis Ntaimo ISEN
Custom Small UAV Lab To: Dr. Lewis Ntaimo ISEN 689-601 From: Gerardo Iglesias, Sugiri Halim, William, Zane Singleton March 20, 2008 I. Statement of Problem Current development and research in the field
More informationARCHITECTURAL TESTING, Inc. Code Compliance Research Report #0774 CCRR-0131
ARCHITECTURAL TESTING, Inc. Code Compliance Research Report #0774 Subject to Renewal: 10/27/09 Issued: 10/27/08 Visit for current status Revised 11/5/08 Page 1 of 10 Solatube International, Inc 2210 Oak
More informationInfrastructure Point Repair System Technical Specifications
4301 A 34 t h Street North St. Petersburg, FL 33714 PH: 877-327-4216 Fax: 727-327- 4118 Web: www.irsi.net Infrastructure Point Repair System 1. Scope: This specification defines the approved methodology
More informationCanSat Competition Guide Mission: Aero-Braking Atmospheric Entry Probe
CanSat Competition Guide 2018 Mission: Aero-Braking Atmospheric Entry Probe Rev 1.2 Sept 15, 2017 1 Table of Contents 1. Introduction 5 1.1 Competition Description 5 2. Mission Overview 6 3. Requirements
More informationElectronics Technology and Robotics III Structure and Materials 1 Administration: General Introduction: Systems Interaction:
Electronics Technology and Robotics III Structure and Materials 1 (Notes primarily from Underwater Robotics Science Design and Fabrication, an excellent book for the design, fabrication, and operation
More informationBlack Powder Rockets 1 / 12
Black Powder Rockets 1 / 12 Rocket Size Designation Table 1: Black Powder Skyrocket Specifications Summary Engine Casing Dimensions (inches) Minimum Stick Length Upper Payload Weight (grams) I.D. O.D.
More informationGreen Country UAS Competition Rules (Ver. 3.2) Released April 30, 2017 The University of Tulsa
Green Country UAS Competition Rules (Ver. 3.2) Released April 30, 2017 The University of Tulsa Competition Date 19-21 May, 2017 Contents Introduction... 3 Schedule... 4 Safety and Security... 5 General
More informationCHAPTER - 1 INTRODUCTION
CHAPTER - 1 INTRODUCTION Development of Space Launch vehicle is critical for the selfreliant programme of space endeavor of any country. The development of Space launch vehicles is with indigenous effort
More informationAUTOMATIC CUT-OFF LA THES for Bar and Tubular Stock
AUTOMATIC CUT-OFF LA THES for Bar and Tubular Stock Chamfer, Form, Groove, Cut Off Up to 8" Tubing; Up to 3" Bar Stock Rugged Construction Application Engineering Automatic Load/Unload Maximum Productivity
More informationSPECIFICATION for ISCO HDPE DUAL CONTAINMENT PIPE
SPECIFICATION for ISCO HDPE DUAL CONTAINMENT PIPE SECTION 15000 MECHANICAL 1. GENERAL 1.1 This specification shall govern the materials and installation of polyethylene dual contained system of pipe, structures
More informationHigh Strength Epoxy Tested in Accordance with ICC-ES AC308
ADHESIVE ANCHORING SPECIALISTS DESCRIPTION/SUGGESTED SPECIFICATIONS* The 100% epoxy resin and hardener are completely mixed as they are dispensed from the dual cartridge through a static mixing nozzle,
More informationATI Evaluation Service A Division of Architectural Testing Certification Services
ATI Evaluation Service A Division of Architectural Testing Certification Services Subject to Renewal: 07/13/2014 Issued: 07/13/2012 Visit www.ati-es.com for current status Revised: 08/22/2012 Page 1 of
More informationHigh Strength Epoxy tested in accordance to ICC-ES AC308
ADHESIVE ANCHORING SPECIALISTS High Strength Epoxy tested in accordance to ICC-ES AC308 2006 IBC Compliant ICC-ES Report No. 1137 DESCRIPTION/SUGGESTED SPECIFICATIONS* The epoxy resin and hardener are
More informationHigh Strength Epoxy Tested in Accordance with ICC-ES AC308
ADHESIVE ANCHORING SPECIALISTS High Strength Epoxy Tested in Accordance with ICC-ES AC308 DESCRIPTION/SUGGESTED SPECIFICATIONS* The epoxy resin and hardener are completely mixed as they are dispensed from
More informationFlorida Method of Test for NONREPETITIVE STATIC PLATE LOAD TEST OF SOILS AND FLEXIBLE PAVEMENT COMPONENTS
Florida Method of Test for NONREPETITIVE STATIC PLATE LOAD TEST OF SOILS AND FLEXIBLE PAVEMENT COMPONENTS 1. SCOPE Designation: FM 5-527 Modified AASHTO T-222-78 1.1 This method covers the making of nonrepetitive
More informationPractical APCP motor design for Amateur & High Power rocketry
Practical APCP motor design for Amateur & High Power rocketry What we will be covering: The basics & definitions Some other considerations The process to get the data to input into the BurnSim program
More informationDESIGN AND TESTING OF THE BQM-167A PARACHUTE RECOVERY SYSTEM
DESIGN AND TESTING OF THE BQM-167A PARACHUTE RECOVERY SYSTEM Richard J. Farhall 1 and Robert J. Sinclair 2 Airborne Systems North America, Santa Ana, CA 92704 and Douglas A. Meyer 3 Composite Engineering
More informationManufacturing Status Review (MSR) Solid Propellant Additive Manufacturing (SPAM)
Manufacturing Status Review (MSR) Solid Propellant Additive Manufacturing (SPAM) Project Purpose SPAM = ROCKET FUEL PRINTER Sinter at least one 1mm layer of rocket candy propellant Control Parameters Heat
More informationHIGH DENSITY CROSSLINKED POLYETHYLENE STORAGE TANKS WITH OXIDATION RESISTANT LINING SYSTEM (NSF/ANSI 61)
PART 1-GENERAL INTEGRALLY MOLDED FLANGED OUTLET (IMFO ) - COMPLETE DRAIN HIGH DENSITY CROSSLINKED POLYETHYLENE STORAGE TANKS WITH OXIDATION RESISTANT LINING SYSTEM (NSF/ANSI 61) 1.01 Requirements 1. The
More informationNRC capabilities in clean energy and resources
NRC capabilities in clean energy and resources Meeting Canada s innovation challenges 2016: hottest year on record for 3 rd consecutive year Energy production and use account for 80% of Canada s greenhouse
More informationAtlas V for Commercial Passenger Transportation
Atlas V for Commercial Passenger Transportation Jeff A. Patton 1 and Joshua B. Hopkins 2 Lockheed Martin Space Systems Company, P.O. Box 179, Denver Colorado 80433 The Atlas and Centaur Programs have enjoyed
More informationShrink-Kon Thin Wall Heat Shrinkable Tubing
Shrink Ratio 2:1 Shrink-Kon Thin Wall Tubing Styles 2:1 Shrink Ratio, Non-Lined Flame retardant. Resistant to common fluids and solvents. Meets UL 224, 125 C; CSA C22.2 No. 198.1, 125 C; MIL-DTL-23053/5
More informationExperimental Flight of KIT Student s Rocket in France
Experimental Flight of KIT Student s Rocket in France Koji Okuda*, Yuji Ujimoto*, Yuta Otsuka*, Takaya Sato*, Takuya Shidooka*, Daijiro Semba*, Kenichi Tominaga*, Junichi Fukuda*, Yuta Yamamoto*, Kazuki
More informationGravity Air Launching of Earth-To-Orbit Space Vehicles
Gravity Air Launching of Earth-To-Orbit Space Vehicles Marti Sarigul-Klijn, Ph.D. *, Nesrin Sarigul-Klijn, Ph.D., Gary C. Hudson and Livingston Holder AirLaunch LLC, Kirkland, Washington, 98033 Gregg Liesman
More informationRate Dependency Plastic Modeling
Rate Dependency Plastic Modeling Hubert Lobo expert material testing CAE material parameters CAE Validation software & infrastructure for materials materials knowledge electronic lab notebooks Considerations
More informationAppendix B- Milestone Review Flysheet
1 Appendix B- Milestone Review Flysheet Milestone Review Flysheet PDR, CDR, FRR Institution Name Tarleton State University Milestone CDR Vehicle Properties Motor Properties Diameter (in) 5.525 Motor Manufacturer
More informationEasy to Use A7 Saves You Time and Money
ADHESIVE ANCHORING SPECIALISTS Easy to Use Saves You Time and Money DESCRIPTION/SUGGESTED SPECIFICATIONS* Fast Dispensing, Fast Curing The acrylic resin and hardening agent are completely mixed as they
More informationPIA TS 135. Parachute Industry Association (PIA) TECHNICAL STANDARD 135
Parachute Industry Association (PIA) TECHNICAL STANDARD 135 MINIMUM PERFORMANCE STANDARDS FOR PERSONNEL PARACHUTE ASSEMBLIES AND COMPONENTS 1. SCOPE: This document defines the minimum performance standards
More informationDIVISION: WOOD, PLASTICS AND COMPOSITES SECTION: STRUCTURAL PLASTICS REPORT HOLDER: HB&G BUILDING PRODUCTS, INC.
0 Most Widely Accepted and Trusted ICC ES Evaluation Report ICC ES 000 (800) 423 6587 (562) 699 0543 www.icc es.org ESR 1361 Reissued 08/2017 This report is subject to renewal 08/2019. DIVISION: 06 00
More informationTACTICAL PARACHUTE DELIVERY SYSTEMS, Inc. HEAVY LOAD TACTICAL (HLT) BROCHURE
TACTICAL PARACHUTE DELIVERY SYSTEMS, Inc. HEAVY LOAD TACTICAL (HLT) BROCHURE 2018 6520 Fort King Road Zephyrhills, FL 33542 USA Phone: +1 813.782.7482 Fax: +1 813.788.2799 E-mail: info@tpdsairborne.com
More informationMECHANICS OF MATERIALS
Lecture Notes: Dr. Hussam A. Mohammed Al- Mussiab Technical College Ferdinand P. Beer, E. Russell Johnston, Jr., and John T. DeWolf Introduction Concept of Stress The main objective of the study of mechanics
More informationFeasibility of Parachute Recovery Systems for Small UAVs
Feasibility of Parachute Recovery Systems for Small UAVs Kirk Graham Stewart Cartwright University of New South Wales Australian Defence Force Academy School of Aerospace, Civil and Mechanical Engineering
More informationAFRL Perspective Responsive & Reusable Boost System (RBS)
AFRL Perspective Responsive & Reusable Boost System (RBS) ASEB-NRC Briefing 17 February 212 Integrity Service Excellence Bruce Thieman Jess Sponable Air Force Research Laboratory DISTRIBUTION STATEMENT
More informationSECTION VIBRATION CONTROLS FOR HVAC PIPING AND EQUIPMENT
SECTION 230548 - PART 1 - GENERAL 1.1 SUMMARY A. This Section includes the following: 1. Elastomeric Isolation pads. 2. Elastomeric Isolation mounts. 3. [Freestanding] [Restrained] [Freestanding and restrained]
More informationScoping & Concept of Operations (ConOps) Module
Scoping & Concept of Operations (ConOps) Module Space Systems Engineering, version 1.0 Space Systems Engineering: Scoping & ConOps Module Module Purpose: Scoping & ConOps To understand the importance of
More informationSECTION SLOPED TRANSLUCENT METAL SKYLIGHT SYSTEM
PART 1- GENERAL 1.1 SUMMARY A. Section Includes: SECTION 084523 - SLOPED TRANSLUCENT METAL SKYLIGHT SYSTEM 1. Flat factory prefabricated structural insulated translucent sandwich panels; with glazed endwalls.
More informationGREEN THREAD Piping Systems
Bulletin No. A1300 February 15, 2006 SMITH FIBERCAST GREEN THREAD Piping Systems PRODUCT GREEN THREAD pipe is filament wound using an amine cured epoxy resin and fiberglass and has a resin-rich liner reinforced
More informationSYSTEMS DESIGN ANALYSIS APPLIED TO LAUNCH VEHICLE CONFIGURATIONS
PREFERRED RELIABILITY PRACTICES PAGE 1 OF 6 SYSTEMS DESIGN ANALYSIS APPLIED TO LAUNCH VEHICLE CONFIGURATIONS Practice: Use design management improvements such as matrix methods, quality techniques, and
More informationCycle Trades for Nuclear Thermal Rocket Propulsion Systems
. AIM 2003-5131 Cycle Trades for Nuclear Thermal Rocket Propulsion Systems Charles E. White, Michael J. Guidos, and William D. Greene NASA Marshall Space Flight Center, Huntsville, AL Abstract Nuclear
More information8 Mission Design and Mission Analysis
Chapter 8 Mission Design and Mission Analysis Table of Contents 8 Mission Design and Mission Analysis... 8-1 8.1 General... 8-1 8.2 Overall Description of Spacecraft to Rockot Launch Vehicle Integration
More informationMERCHANTS METALS. A. ASTM F552 Standard Terminology Relating to Chain Link Fencing
MERCHANTS METALS SECTION 32 31 13 COLORBOND CHAIN LINK FENCE AND GATES 2014 PART 1 GENERAL 1.1 RELATED DOCUMENTS A. DIVISION 01 - GENERAL REQUIREMENTS: Drawings, quality, product and performance requirements,
More informationSTAINLESS STEEL SHEETS
STAINLESS & NICKEL ALLOY CHATHAM STEEL CORPORATION 59 STAINLESS STEEL SHEETS TYPE 04, 04L, 6, 6L No. 2B Finish Cold Rolled, Annealed *No. 2D Finish No. Finish Polished One Side No. 4 Finish Polished One
More informationModel-Based Concept Development
INNOVATIONS IN ENGINEERING Model-Based Concept Development Brian London Draper Laboratory blondon@draper.com (617)258-3059 NDIA Systems Engineering Conference 22 October 2012 San Diego, CA Agenda Problem
More informationBAY POLES FOR LOAD BEARING WINDOWS
BAY POLES FOR LOAD BEARING WINDOWS From Nicholls & Cooke The Pole Calculations Ordering Head and Base Plates New Build Box Support Anti Bounce Bars Universal Poles Slack Adjuster Kits Deceurninck Series
More informationVision VTOL. The Future of Flight
Vision VTOL The Future of Flight What if batteries had just 10 times their current power density? What would an aircraft look like? What could it do? Wings become obsolete. Motors become as reliable as
More informationContact. Reaction Engines Ltd Building D5, Culham Science Centre, Abingdon, Oxon, OX14 3DB, UK.
SKYLON USERS MANUAL Contact One of the purposes of this document is to elicit feedback from potential users as part of the validation of SKYLON s requirements. Comments are most welcome and should be sent
More informationSSL Payload Orbital Delivery System (PODS) FedEx to GTO/GEO
SSL Payload Orbital Delivery System (PODS) FedEx to GTO/GEO June 11th, 2014 For more information, contact: Al Tadros, SSL Email: alfred.tadros@sslmda.com Tel: (650) 714-0439 Cost-Effective, Frequent, Quick
More informationPROJECT DEVELOPMENT AND THERMAL MANAGEMENT FOR A PROPOSED HYPERSONIC SCRAMJET FLIGHT TEST
PROJECT DEVELOPMENT AND THERMAL MANAGEMENT FOR A PROPOSED HYPERSONIC SCRAMJET FLIGHT TEST Elizabeth M. Croft University of Virginia, Charlottesville, Virginia 94 Dr. Christopher P. Goyne, Advisor The latest
More informationSLI 2011 Statement of Work Madison West High School EFFECTS OF GRAVITATIONAL STRESS AND SUNLIGHT ON THE BEHAVIOR OF SLIME MOLDS
SLI 2011 Statement of Work Madison West High School September 27, 2010 EFFECTS OF GRAVITATIONAL STRESS AND SUNLIGHT ON THE BEHAVIOR OF SLIME MOLDS Front Row: Suzanne, Nhien, Zoë, Stephen Back Row: Ivy,
More informationNSU TARA 2017 AUVSI SUAS JOURNAL PAPER
NSU TARA 2017 AUVSI SUAS JOURNAL PAPER Norfolk State University Terrestrial Aircraft for Reconnaissance Applications Department of Engineering Department of Computer Science Norfolk State University, Norfolk,
More informationBLOCKTITE SYSTEM WATER-REPELLENT ADMIXTURE CERTIFICATION PROGRAM
BLOCKTITE SYSTEM WATER-REPELLENT ADMIXTURE CERTIFICATION PROGRAM Mix Performance Worksheet Testing Procedures/Protocol Test Results, Calculations Certificate of Compliance The Euclid Chemical Company 19218
More informationCode Compliance Research Report CCRR-0194
Code Compliance Research Report CCRR-0194 Issued: 09-16-2013 Renewal Due: 09-16-2018 Revised: 10-12-2017 DIVISION: 06 00 00 WOOD, PLASTICS AND COMPOSITES Section: 06 05 23 Wood, Plastic, and Composite
More informationFlorida Structural Engineers
Florida Structural Engineers South Florida Chapter January 8, 2008 Miami Lakes, Florida Aluminum Association of Florida, Inc. Joe Belcher ~ David Miller AAF Code Involvement: Historical Perspective 1998:
More informationSecondary Launch Services and Payload Hosting Aboard the Falcon and Dragon Product Lines
Secondary Launch Services and Payload Hosting Aboard the Falcon and Dragon Product Lines Dustin Doud, Brian Bjelde, Christian Melbostad, Lauren Dreyer Space Exploration Technologies Corp. 1 Rocket Road,
More informationSmall Satellite Rideshares on Commercial Resupply Missions to the International Space Station
SSC12-V-2 Small Satellite Rideshares on Commercial Resupply Missions to the International Space Station Joshua R. Robinson and Daniel W. Kwon Orbital Sciences Corporation 45101 Warp Drive Dulles, VA 20166
More informationSECTION VIBRATION AND SEISMIC CONTROLS FOR ELECTRICAL SYSTEMS
PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions, apply to this Section. 1.2 SUMMARY A. This Section includes the
More informationSteel Pole Research. Professor Jeffrey Packer. American Iron and Steel Institute. University of Toronto
Steel Pole Research Professor Jeffrey Packer American Iron and Steel Institute Wood Poles Environmentalists are opposing logging & non-replacement. Long, straight poles are becoming difficult to obtain.
More informationThe following are details of the code requirements of the 2015 International Residential Code for single-story decks.
The following are details of the code requirements of the 2015 International Residential Code for single-story decks. The 2015 International Residential Code Section R507 contains additional information
More informationDevelopment of Low Cost Propulsion Systems for Micro-Satellite Launch Vehicles
Development of Low Cost Propulsion Systems for Micro-Satellite Launch Vehicles Dr.-Ing. Peter H. Weuta Dipl.-Ing. Neil Jaschinski WEPA-Technologies GmbH 51375 Leverkusen / Germany info@wepa-technologies.de
More informationSECTION HIGH DENSITY POLYETHYLENE PIPE AND FITTINGS
SECTION 02620 PART 1 GENERAL 1.1 SCOPE OF WORK A. Furnish all labor, materials, equipment, and incidentals required to install High Density Polyethylene (HDPE) pressure pipe, fittings, and appurtenances
More information1. Hangers and supports for electrical equipment and systems. 2. Construction requirements for concrete bases.
SECTION 260529 - HANGERS AND SUPPORTS PART 1 - GENERAL 1.1 SUMMARY A. Section includes: 1. Hangers and supports for electrical equipment and systems. 2. Construction requirements for concrete bases. 1.2
More informationSimulation based design & development of autonomous underwater vehicle IMGAM
Simulation based design & development of autonomous underwater vehicle IMGAM Dr. Ing. Max Abildgaard a sound decision The ATLAS ELEKTRONIK Group/ 1 Introduction IMGAM (Intelligentes Monitoring von Gasaustritten
More informationTHE BOXEL BUNDLER FALL 2010 DESIGN PROPOSAL
THE BOXEL BUNDLER FALL 2010 DESIGN PROPOSAL Gary Gray Team Lead Biosystems Engineering Evan Foster Biosystems Engineering Alice White Agricultural Communications/Agribusiness Jeremy McCasland Agricultural
More informationTEST PROCEDURE FOR AIR PERMEABILITY TESTING OF RIGID, DISCONTINUOUS ROOF SYSTEMS
TESTING APPLICATION STANDARD (TAS) 116-95 TEST PROCEDURE FOR AIR PERMEABILITY TESTING OF RIGID, DISCONTINUOUS ROOF SYSTEMS Scope 1.1 This Protocol covers the determination of the air permeability characteristics
More informationPRODUCT CONTROL SECTION
MIAMI-DADE COUNTY PRODUCT CONTROL SECTION 11805 SW 26 Street, Room 208 DEPARTMENT OF REGULATORY AND ECONOMIC RESOURCES (RER) Miami, Florida 33175-2474 BOARD AND CODE ADMINISTRATION DIVISION T (786)315-2590
More informationMANUFACTURING PROCESSES
1 MANUFACTURING PROCESSES - AMEM 201 Lecture 8: Forming Processes (Rolling, Extrusion, Forging, Drawing) DR. SOTIRIS L. OMIROU Forming Processes - Definition & Types - Forming processes are those in which
More informationQuality and Process Variability in Ti-6Al-4V Powder Bed Electron Beam Additive Manufacturing
Quality and Process Variability in Ti-6Al-4V Powder Bed Electron Beam Additive Manufacturing Northrop Grumman Aerospace Systems 2015 Euromold September 25, 2015 Eric Fodran, Ph.D. EBM AM In-Process Surface
More informationATI Evaluation Service A Division of Architectural Testing Certification Services
ATI Evaluation Service A Division of Architectural Testing Certification Services Subject to Renewal: 05/08/2016 Issued: 08/12/2015 Visit www.ati-es.com for current status Page 1 of 21 Fiber Composites,
More informationLD21 NEW MATERIALS FOR LARGE-CALIBER ROTATING BANDS FOR HIGH CHARGES. M. Schupfer1, K. Steinhoff2, R. Röthlisberger1 1.
LD21 19th International Symposium of Ballistics, 7 11 May 2001, Interlaken, Switzerland NEW MATERIALS FOR LARGE-CALIBER ROTATING BANDS FOR HIGH CHARGES M. Schupfer1, K. Steinhoff2, R. Röthlisberger1 1
More informationJEM Exposed Facility System and Operation
JEM Exposed Facility System and Operation TAKATA Masaharu : Manager, Space Systems Department, IHI Aerospace Co., Ltd. International Space Station ( ISS ) is currently constructing. For Japanese Experiment
More informationCFFWA-20-1-U Chilled/Hot Water Universal Mount Fan Coil 2-Pipe Heat / Cool Fan Coil 60,000 BTUH
CFFWA-20-1-U Chilled/Hot Water Universal Mount Fan Coil 2-Pipe Heat / Cool Fan Coil 60,000 BTUH Rev. 1.3 HVAC Guide Specifications Chilled and Hot Water Universal Mount Fan Coil 2-Pipe Nominal Size: 60,000
More informationDIVISION: EARTHWORK SECTION: BORED PILES REPORT HOLDER: GEOTECH ENTERPRISES, INC.
0 Most Widely Accepted and Trusted ICC ES Report ICC ES 000 (800) 423 6587 (562) 699 0543 www.icc es.org ESR 3623 Reissued 04/2017 This report is subject to renewal 04/2018. DIVISION: 31 00 00 EARTHWORK
More informationTypes of Hydropower Facilities
Types of Hydropower Facilities 1 Impoundment Hydropower- uses a dam to store water. Water may be released either to meet changing electricity needs or to maintain a constant water level. 2 Run-of-River
More informationHigh Strength Epoxy tested in accordance to ICC-ES AC308
ADHESIVE ANCHORING SPECIALISTS High Strength Epoxy tested in accordance to ICC-ES AC308 2006 IBC Compliant ICC-ES Report No. 1137 DESCRIPTION/SUGGESTED SPECIFICATIONS* The epoxy resin and hardener are
More informationAdvantages of Composite Materials in Aircraft Structures
Advantages of Composite Materials in Aircraft Structures Muniyasamy Kalanchiam, and Moorthy Chinnasamy Abstract In the competitive environment of aircraft industries it becomes absolutely necessary to
More informationWEIR PLATES & SCUM BAFFLES
WEIR PLATES & SCUM BAFFLES Bedford Reinforced Plastics Weir Plates and Scum Baffles are available in any SIZE, any LENGTH and any CONFIGURATION Benefits Corrosion Resistant Maintenance Free Strong Easy
More informationDESIGN AND TESTING OF THE KISTLER LANDING SYSTEM PARACHUTES
DESIGN AND TESTING OF THE KISTLER LANDING SYSTEM PARACHUTES Anthony P. Taylor *, Robert J. Sinclair, Richard D. Allamby, M.B.E. Irvin Aerospace Inc., Santa Ana, California 9274 The Kistler Landing system
More informationEME6325D WIND-DRIVEN RAIN RESISTANT STATIONARY LOUVER
3900 Dr. Greaves Rd. Kansas City, MO 64030 (816) 761-7476 FAX (816) 765-8955 EME6325D WIND-DRIVEN RAIN RESISTANT STATIONARY LOUVER MIAMI-DADE APPROVED MIAMI-DADE COUNTY, FLORIDA NOTICE OF ACCEPTANCE NUMBER:
More informationMiniature Aircraft Deployment System (MADS) Approval Name Affiliation Approved Date Customer Eric Frew CU Advisor #2
University of Colorado Department of Aerospace Engineering Sciences Senior Projects ASEN 4018 Miniature Aircraft Deployment System (MADS) (PDD) Document History Release Version Date Description of Top
More informationINDIAN INSTITUTE OF TECHNOLOGY GANDHINAGAR Department of Civil Engineering Soil Mechanics Laboratory
UNCONSOLIDATED UNDRAINED TRIAXIAL COMPRESSION (UU) TEST (IS 2720-Part 11-1993) Reaffirmed-2 THEORY: 1. A loading frame in which the load is applied by yoke acting through an elastic dynamometer, more commonly
More informationC6+ High Strength Epoxy for All. conditions. One product for most environmental conditions and weather conditions. Curing Times
ADHESIVE ANCHORING SPECIALISTS High Strength Epoxy for All Conditions DESCRIPTION/SUGGESTED SPECIFICATIONS* One product for most environmental conditions and weather conditions Design and use with confidence
More informationAeroVironment, Inc. Unmanned Aircraft Systems Overview. Background
AeroVironment, Inc. Unmanned Aircraft Systems Overview Background AeroVironment ( AV ) is a technology company with a 40-year history of practical innovation in the fields of unmanned aircraft systems
More informationMicro-Aerial Vehicles Materials & Structures
Micro-Aerial Vehicles Compiled by Dr Alan Hooper and Dr Eoin O Keefe Schloss Elmau, Garmisch-Partenkirchen, Germany. 22-24 September 2003 Report Documentation Page Form Approved OMB No. 0704-0188 Public
More informationUNCLASSIFIED. Overview. Objective History Approach Progress Summary Conclusions UNCLASSIFIED
Unclassified A FAST COOK OFF ASSESSMENT OF U.S. NAVY LEGACY WEAPONS Weapons Division M. K. Rattanapote, A. I. Atwood, S. E. Towne, S. S. Johnson, M. C. Buffum, J. E. Wilson, and V. L. Brady Naval Air Warfare
More informationSSC06-IX-7. Lessons Learned Developing Separation Systems For Small Satellites
Lessons Learned Developing Separation Systems For Small Satellites Walter Holemans, 20 th Annual AAIA/USU, August 2006 Planetary Systems Corporation, 2303 Kansas Avenue, Silver Spring MD 20910, (301) 495-0737,
More informationSTRESS ANALYSIS OF A REAR PRESSURE BULKHEAD OF THE FUSELAGE STRUCTURE AND FATIGUE LIFE ESTIMATION
Int. J. Mech. Eng. & Rob. Res. 2013 Sreyas Krishnan S et al., 2013 Research Paper ISSN 2278 0149 www.ijmerr.com Vol. 2, No. 2, April 2013 2013 IJMERR. All Rights Reserved STRESS ANALYSIS OF A REAR PRESSURE
More information