32 Inch Touch Screen Specification

Transcription

1 32 Inch Touch Screen Specification Mode Name PCT5L32SBR-1093 Touch Technology Projected Capacitive Touch (P-Cap) Rev 0.1 1

2 Content 1) Introduction a. Definition b. Features and General Specification ) Appearance Inspection a. Inspection Condition b. Appearance Limit Standard ) Controller ) Cover lens ) Structure ) Electronic Characteristics ) Reliability ) Durability ) Application ) Operation Instruction ) Drawing

3 1. Introduction 1.1 Definition It s a projected touch panel with USB interface. It can be operated under Windows 7,Win8,Win10, Android, Linux OS and can realize 10 point touch. 1.2 Features and General Specification Item Contents Unit Size 32 inch Total Thickness 4.40 ±0.30 mm Outline of Cover Lens * ±0.5 mm Outline of ITO Sensor * ±0.5 mm Active Area * ±0.5 mm Number of touch point 10 Interface Controller IC USB ILI2312 Response time 10 ms Working temperature and Humidity(Non-condensing) Input -10~+60, 20~85% RH Hand writing or capacitive pen Transmittance 83% Surface Hardness Application 7H It s applied in ordinary electric equipments and automatic office facilities. 3

4 2. Appearance Inspection 2.1 Inspection Condition 1. Environment: 22 ± 3ºC, Inspection distance:30 ± 2cm. 2. Vertical rotating angle : ±75 (from up to down); Horizontal rotating angle :±75 (from left to right) 3. illuminance :1000~1200Lux 4. I n s p e c t i o n P e r i o d Front and back surfaces: 45 seconds, Each side: 1-2 seconds. 2.2 Appearance Inspection Standard 4

5 Linear object Concave/Covex edge/bubbles 1 D<0.35mm, DS>10mm,N 5; ignored mm D 0.5mm, DS>10mm, N 2 ; ignored. 3 Others are not allowed. X 3mm,Y 3mm,Z GT; ignored Corner chip X: Length; Y: Width; Z: Thickness Side chip X 8mm, Y 3mm, Z GT; ignored X: Length; Y: Width; Z: Thickness Color of cover lens/logo typeface/shade of background Color shows no difference from that of the samples. Clear typeface and clear pattern Less than 3mm tolerance is allowed..good shield of back color Notes For other particles or linear objects, refer to the criteria above Number of defect for each piece: N 10, DS 10mm. 5

6 3. Controller IC VID/PID Interface Power Supply Response time Accuracy ESD EMI EMS ILI2312 VID_222A/PID_A16C USB 5.0 ± 0.5V DC 10ms ±2.0mm(Center) IEC ,Contact 4KV,Air 8KV EN 55022,CLASS B IEC Cover Lens Items Pressure Value Ball Drop Test Contents 400 ~500 mpa above 6u 227g±2g, 35cm, No damage after the impact at the central area for once. Hardness 7H Pencil: 7H Pressure: 1N/45. Note 1 :The ball drop test illustration is shown as follows. 6

7 Note 2 : The hardness test follows the JIS K-5400 series industry standard and the test is shown as below. 7

8 5. Structure Items Contents Notes 1 st layer Cover Lens/Glass Thickness: 4.0±0.2mm 2 nd layer UV glue (OCA ) Thickness: 0.3±0.05mm 3 rd layer ITO Glass (free of etching lines on one surface ) Thickness:1.1±0.05mm 6. Electronic Characteristics Items ESD (Machine) ESD (Body) Contents ±300V 200pF, 0 Ω, 3 times ±1000V, 100pF, 1500Ω, 3 times 8

9 ESD (Touch) ESD (Air) 4KV, 100pF, 1500Ω, 3 times 8KV, 100pF, 1500Ω, 3 times Note 1: In order to make a touch panel work functionally well, please make sure that the host device is grounded. Note 2: All environmental characteristics listed above should be less than 1 atmospheric pressure. Note3 :The touch panel must be assembled with LCD panel by VHB or other materials. The control board should be fixed on LCM bezel or other mechanical parts of the system and then be grounded; In ESD test, the touch panel should work normally and there should be no damage to the appearance, when no static electricity discharges. However, irregular changes like display flickering are acceptable when static electricity discharges. Note4: The touch panel may be damaged functionally or work unstably if the touch panel is not grounded properly. Note5: In order to make a touch panel work normally, power supply or power adapter has to conform to IEC Reliability Items Contents Notes Working temperature and humidity -10~+60, 20~85% RH non-condensing Storage temperature and humidity Humidity resistance -20~+70, 20~85% RH non-condensing 85% RH, 120H non-condensing Heat resistance 70, 120H non-condensing Cold resistance -20, 120H non-condensing Thermal shock Humidity resistance Heat resistance Cold resistance -10 (0.5hour)-60 (0.5hour) by 50 cycles The product will not be influenced after being exposed under 85% RH for 120 hours and then exposed under normal temperature and humidity for 24 hours. The product will not be influenced after being exposed at 70 for 120 hours and at normal temperature and humidity for 24 hours. The product will not be influenced after being exposed at -20 for 120 hours and at normal temperature and humidity for 24 hours. non-condensing non-condensing non-condensing non-condensing 9

10 Thermal shock The product will not be influenced after being exposed at -20 (0.5 hour) hour )by 50 cycles and at normal temperature for 24 hours non-condensing 8. Durability Items Contents Notes Panel Hitting life SlideTest 250g, 20mm, 100,000 times 35,000,000 times Durability test may cause slight scratch on surface, but the function stays intact. Durability test may cause surface slight Scratch, yet the function stays intact 9. Application Instructi 9.1 Environment Items Contents Notes Temperature -10~60ºC Humidity 20~85% RH 10

11 10. Operation Instruction Storage Unloading Store panels under the temperature and humidity range prespecified. Direct sunlight exposure or piling should be avoided. Unpack the box with the printed red arrow pointing up. Handling (1) Use clean finger sheaths or gloves to prevent fingerprints and/or stains on the panel. Extra attention and carefulness should be taken while handling the glass edge. (2) Avoid touching the viewing area before installation /integration. (3) Holding the panel instead of the tail (FPC )all the time. Cleaning (1) Use neutral detergent or isopropyl alcohol on a clean soft cloth to clean the panel surface. (2) Prevent using any kind of chemical solvent, acidic or alkali solution. Installation Operating Others (1) Excessive force or strain to the panel or tail is prohibited. (2) Retain at least 0.5 mm clearance between panel and display module. (3) Gasket or cushion pads around the edge of the panel may segregate water and/or dust contamination. (1) Touch the panel with your finger or stylus only to assure normal operation. Any sharp edged or hard objects are prohibited. (2) Operate the panel in a steady environment. Abrupt variation on temperature and humidity may cause malfunction of the panel. (1) Keep the panel surface clean. Prevent any kind of adhesive being sticked on the surface. (2) Avoid high voltage and/or static charge. 11. Drawing(Screen) 11

12