D PROCESSES WITH NADCAP MANDATE (Sorted by Specification Number)

Transcription

1 Commodity 1P00075 H152 HT 7102 Heat Treatment of Titanium Alloys 1P00095 H701 COMP 7118 MB Adhesive Bonding Multicomponent Structural 1P00097 H702 COMP 7118 MB Adhesive Bonding Structural 5PTPHB26A 323D CP 7108/1 Sol Gel Surface Treatment for Painting Titanium Alloys AA P253 WLD 7110, 7110/1 Brazing of Aluminum Torch AA P253A HT 7102/1 Brazing of Aluminum Furnace Dip AA P251 WLD 7110, 7110/1 Silver Alloy Brazing Torch Induction AA P251A HT 7102/1 Silver Alloy Brazing Furnace AA P366 CP 7108 Electroless Nickel Phosphorus Plating SMPP Required AA P320 CP 7108 Application of Chemical Films to Aluminum Alloys (Immersion Application Only) AA P313 CP 7108 Anodizing of Aluminum Alloys for P106 AA P141A HT 7102 Heat Treatment of Nickel Based Alloys AA P122 HT 7102 Thermal Treatment of Beryllium AA P103 HT 7102 Annealing of Electrical Steels AA P141B HT 7102 Termal Selected Ni Iron Base Maxidem Stability AA P121 HT 7102 Heat Treatment of Copper and Copper Alloys AA P105 HT 7102 Heat Treatment of Magnetic Alloys AA P111 HT 7102/2 Heat Treatment of Aluminum Alloys AA P390 CP 7108/1 Application of Phosphoric Acid Bonded Dry Film Lubricant AMS B CP 7108 Plating Electroless Nickel AMS A CP 7108 Tin Plating AMS A CP 7108 Silver Plating AMS B CP 7108 Silver Plating AMS CP 7108 Silver Plating AMS CP 7108 Diffused Nickel Cadmium Plating AMS A CP 7108 Zinc Nickel Alloy Plating AMS A CP 7108 Plating Copper AMS SE 7117 Shot Peening AMS SE 7117 Shot Peening AMS A CP 7108 Chromium Plating Thin Hard Dense AMS A CP 7108 Hard Coating Aluminum AMS B CP 7108 Hard Coating Aluminum AMS A CP 7108 Black Oxide Coating AMS CP 7108 Anodic Treatment of Titanium AMS A NDT 7114/3,7114/3S NDI Ultrasonic AMS A WLD 7110, 7110/1 Brazing Aluminum Torch AMS H HT 7102/1 Brazing Aluminum Furnace AMS B HT 7102/1 Dip Brazing Aluminum AMS HT 7102/1 Nickel Brazing of Steel CRES Heat Resistant Alloys AMS A WLD 7110/3 Electron Beam Welding for Fatigue Critical Application AMS B WLD 7110/3 Electron Beam Welding AMS WLD 7110/13 Welding Tungsten Arc Inert Gas AMS HT 7102 Heat Treatment of Steel Parts General Requirements AMS HT 7102 Heat Treat of Corrosion Resistant Steel AMS 2759/1 103A HT 7102 Heat Treatment of Carbon and Low Alloy Steel Parts <220 PSI AMS 2759/10 103K HT 7102/4 Automated Gaseous Nitriding Controlled by Nitriding Potential AMS 2759/2 103B HT 7102 Heat Treatment of Low Alloy Steel Parts >220 PSI AMS 2759/3 103C HT 7102 Heat Treatment Precipitation Hardening Corrosion Resistant and Maraging Steel Parts AMS 2759/4 103D HT 7102 Heat Treatment Austenitic Corrosion Resistant Steel Parts AMS 2759/5 103E HT 7102 Heat Treatment Martensitic Corrosion Resistant Steel Parts AMS 2759/6 103F HT 7102/4 Gas Nitriding and Heat Treatment of Low Alloy Steel Parts AMS 2759/7 103G HT 7102/3 Carburizing and Heat Treatment of Carburizing Grade Steel Parts AMS 2759/8 103H HT 7102/4 Ion Nitriding AMS 2759/9 103J HT 7102 Hydrogen Embrittlement Relief (Baking) of Steel Parts AMS HT 7102 Heat Treatment of Magnesium Alloy Castings AMS HT 7102/2 Heat Treat of Wrought Aluminum Alloys AMS HT 7102/2 Heat Treatment of Aluminum Alloy Castings AMS HT 7102/2 Heat Treatment of Aluminum Alloy Raw Materials AMS HT 7102 Heat Treatment Wrought Nickel Alloy and Cobalt Alloy Parts AMS HT 7102 Heat Treatment of Titanium Alloy Parts AMS WLD 7110, 7110/2 Flash Welding of CRES and Austenitic Steel AMS D CP 7108 Hard Anodic Coating of Magnesium Alloys Alkaline Type High Voltage AMS B CP 7108 Anodic Treatment of Magnesium Alloys Acid Type Full Coat AMS C CP 7108 Anodic Treatment of Magnesium Alloys Acid Type Thin Coat Page 1 of 14 9/19/2017

2 Commodity AMS B HT 7102/5, 7101/5 Optional Hardness and Conductivity Inspection of Wrought Aluminum Alloy Parts AMS C HT 7102/5, 7101/5 Optional Hardness and Conductivity Inspection of Wrought Aluminum Alloy Parts AMS C C CP 7108 Coatings Electroless Nickel Requirements for AMS H A HT 7102/2 Heat Treat of Aluminum Alloys AMS H A HT 7102 Heat Treat of Alloy Steels AMS H A HT 7102 Heat Treat of Corrosion Resistant Steel AMS H A HT 7102 Heat Treatment of Wrought Copper Beryllium Alloys for AMS H A HT 7102 Heat Treatment of Titanium and Titanium Alloys AMS M B CP 7108 es for Pretreatment and Prevention of Corrosion on Magnesium Alloy AMS P D CP 7108 Tin Lead Electroplate AMS QQ C B CP 7108 Chromium Plating (Electrodeposited) AMS QQ N A CP 7108 Nickel Plating (Electrodeposited) AMS QQ P A CP 7108 Plating Cadmium (Electrodeposited) AMS S A SE 7117 Shot Peening AMS STD B NDT 7114/3,7114/3S Ultrasonic Inspection of Flat Surface Shapes AMS STD A NDT 7114/3,7114/3S Ultrasonic Inspection of Rounds and Shapes AMS STD WLD 7110/13 Fusion Welding for A/S App Steel CRES Heat Resist Alloys AMS STD B WLD 7110/13 Fusion Welding for Aerospace Applications Aluminum Alloys AMS STD B WLD 7110/13 Fusion Welding for Aerospace Applications Magnesium Alloys AMS STD C WLD 7110/13 Fusion Welding for Aerospace Applications Titanium Alloys AMS W A WLD 7110/4 Resistance Welding Nickel Cobalt Base Alloys ASTM D NDT 7114/3,7114/3S NDI Ultrasonic ASTM E10 806E HT 7102/5, 7101/5 Optional Standard Test Method for Brinell Hardness of Metallic Materials ASTM E18 806D HT 7102/5, 7101/5 Optional Standard Test Methods for Rockwell Hardness of Metallic Materials ASTM B CP 7108/4 Salt Spray Testing ASTM B A CP 7108 Chromates on Aluminum (Immersion Application Only) ASTM B 488 N371A CP 7108 Electrodeposited Coatings of Gold for Engineering Uses (DIV N P R ONLY) ASTM B A CP 7108 Electrodeposited Coatings of Tin ASTM B C CP 7108 Standard for Electrodeposited Coatings of Silver for Engineering Use ASTM D A CP 7108/3 Phosphoric Acid Anodizing of Aluminum for Structural Bonding ASTM E NDT 7114/1,7114/1S Penetrant Inspection ASTM E NDT 7114/2,7114/2S Magnetic Particle Inspection ASTM E MTL 7101/1 & /2 Determination of Hydrogen in Titanium ASTM E A NDT 7114/1 Standard Practice for Radiographic Inspection ASTM E E NDT 7114/3,7114/3S Ultrasonic Inspection of Flat Surfaces ASTM E C NDT 7114/3,7114/3S Ultrasonic Inspection of Rounds and Curved Shapes ASTM E MTL 7101/1 & /3 Fracture Toughness Testing AWS C C WLD 7110, 7110/1 Torch Brazing AWS C D WLD 7110, 7110/1 Induction Brazing AWS C E HT 7102/1 Furnace Brazing AWS C F WLD 7110, 7110/1 Aluminum Brazing Torch Induction AWS C J HT 7102/1 Aluminum Brazing Furnace Dip AWS D A WLD 7110/13 Spec for Fusion Welding for Aerospace Applications for Steel CRES and Heat Resistant Alloys AWS D A WLD 7110/13 Spec for Fusion Welding for Aerospace Applications for Aluminum Alloys AWS D A WLD 7110/13 Spec for Fusion Welding for Aerospace Applications for Magnesium Alloys AWS D B WLD 7110/13 Spec for Fusion Welding for Aerospace Applic for Titanium Alloys AWS QC1 812A WLD 7110/3, 7110/5, 7110/6, 7110/12, 7110/13 Certified Visual Weld Inspector BAC CP 7108 Chromic Acid Anodizing Class 1 and 4 BAC CP 7108 Chromic Acid Anodizing Class 1 and 3 BAC CP 7108 Chromic Acid Anodizing Class 5 BAC CP 7108 Sulfuric Acid Anodizing Page 2 of 14 9/19/2017

3 Commodity BAC COMP 7118 PAR & CP, (CP only with F4 Limitation, PAR only with F10 Limitation) Fiber Reinforced Composite Parts (QPL) BAC COMP 7118 PAR & CP Carbon and Aramid Reinforced Composite Parts 350F Cure (QPL) BAC COMP 7118 PAR & CP Manufacturing of Low Temperature Autoclave Cure Epoxy Structural Parts (QPL) BAC COMP 7118 PAR & CP Mfg. of High Temperature Resistant Epoxy Str. Parts (QPL) BAC COMP 7118 PAR & CP Adv. Composite Honeycomb Sandwich Str. Parts (QPL) BAC COMP 7118 PAR & CP Mfg. of Adv. Composite Structural Parts 250F Cure (QPL) BAC COMP 7118 PAR & CP Manufacture of Perforated Carbon Fiber Reinforced Parts (QPL) BAC COMP 7118 PAR Manufacture of Composite Parts by Bulk Resin Infusion (BRI) ing (QPL) BAC COMP 7118 PAR Manufacture of Fiber Reinforced Bismaleimide (BMI) Matrix Composite Parts BAC NDT 7114/1,7114/1S Penetrant Inspection BAC NDT 7114/2,7114/2S Magnetic Particle Inspection BAC CP 7108/2 Etch Inspection of Ground or Machined Steel Parts BAC NDT 7114/3,7114/3S Ultrasonic Inspection Longitudinal Wave BAC NDT 7114/3,7114/3S Ultrasonic Inspection Shear Surface Lamb Wave BAC NDT 7114/3,7114/3S Ultrasonic Inspection of Welds BAC NDT 7114/3,7114/3S Ultrasonic Inspection of Tubing BAC NDT 7114/3,7114/3S UT Insp Plate and Flat Obsolete Superseded by BSS 7055 BAC NDT 7114/3,7114/3S UT Insp Rounds Shapes Obsolete Superseded by BSS 7055 BAC COMP 7118 MB Structural Bonding Class MM per D (QPL) BAC COMP 7118 MB & CP (MB not required with F4 Limitation) Structural Bonding Class HC per D (QPL) BAC COMP 7118 PAR & CP Manufacture of Polyimide Structural Laminates and Honeycomb Sandwich (QPL) BAC CP 7108/3 Phosphoric Acid Anodize (QPL) BAC COMP 7118 PAR Mfg. of Carbon Fiber Reinforced Adv. Composite parts (QPL) BAC HT 7102/2 Heat Treat of Aluminum Alloys BAC CP 7108 Conversion Coating on Magnesium (Dow 7) BAC HT 7102 Heat Treat of Copper Copper Alloys BAC HT 7102 Heat Treat of Titanium and Titanium Alloys BAC HT 7102 Heat Treat of Nickel Cobalt Base Alloy BAC HT 7102 Heat Treat of Alloy Steels BAC HT 7102 Heat Treat of Corrosion Resistant Steel BAC CP 7108 Colored Chem Conversion Coatings for Alum Immersion App only BAC CP 7108 Boric Acid Sulfuric Acid Anodizing Class 1 BAC CP 7108 Boric Acid Sulfuric Acid Anodizing Class 5 BAC CP 7108 Zinc Nickel Alloy Plating BAC HT 7102/4 Nitriding of Steel BAC HT 7102/3 Carburizing of Steel BAC COMP 7118 PAR Manufacture of Carbon Fiber Reinforced Composite Structure by Automated Fiber Placement 350 Cure Epoxy Systems BAC A CP 7108/1 Sol Gel Conversion Coatings for Aluminum Alloys BAC C CP 7108 Low Hydrogen Embrittlement Stylus Zinc Nickel Alloy Plating BAC CP 7108/1 Application of Sol Gel Conversion Coatings on Corrosion Resistant Alloys for Painting BAC A WLD 7110/13 Fusion Welding of Girth Joints in 5080 PSI (35 MPA) Systems Tubing BAC E CP 7108/3 Application of Sol Gel Coatings for Adhesive Bonding of Ti & Ti Alloys BAC B CP 7108 Low Hydrogen Embrittlement (LHE) Zinc Nickel Alloy Plating (QPL) BAC CP 7108 Cadmium Plating Types I II BAC CP 7108 Cadmium Plating Type III BAC CP 7108 Hard Chromium Plating Class 1 and 2 BAC CP 7108 Hard Chromium Plating Class 3 BAC CP 7108 Hard Chromium Plating Class 4 (QPL) BAC CP 7108 Electroplating of Aluminum BAC CP 7108 Silver Plating BAC CP 7108 Tin Plating Types I and II BAC A CP 7108 Low Hydrogen Embrittlement Cadmium Plating BAC CP 7108 Chemical Conversion Coatings for Aluminum (Immersion Application Only) BAC CP 7108 Copper Plating BAC CP 7108 Electroless Nickel Plating BAC SE 7117 Shot Peening Page 3 of 14 9/19/2017

4 Commodity BAC SE 7117 Shot Peening (Boeing Helicopters only) BAC SE 7117 Shot Peen Forming BAC SE 7117 Shot Peening Self Contained BAC CP 7108 Anodizing of Magnesium (Dow 17 ) BAC CP 7108 Nickel Plating Types I and II BAC CP 7108 Nickel Plating Type III (QPL) BAC CP 7108/2 Cleaning Descaling of Titanium Method II Only BAC CP 7108 Chemical Milling of Steel Nickel Cobalt BAC CP 7108 Chemical Milling of Aluminum Type I (QPL) BAC CP 7108 Chemical Milling of Aluminum Type I and II (QPL) BAC CP 7108/1 Application Corrosion Resistant Finish for Integral Fuel Tanks manual touch up excluded for requiring approval BAC CP 7108 Low Hyd. Embrittlement Cadmium/Titanium Plating (QPL) BAC CP 7108 Phosphate Conversion Coating on Steel BAC CP 7108/1 Dry Film Lubricant Type VIII Only (QPL) BAC CP 7108 Hard Anodizing Class 1 and 2 BAC CP 7108 Chemical Milling of Titanium Alloys (QPL) BAC CP 7108 Brush Plating Cadmium only BAC CP 7108 Low Hydrogen Embritt. Stylus Cadmium Plate BAC CP 7108 Phosphate Fluoride Coatings Titanium BAC CP 7108 Anodizing of Aluminum Alloys BAC HT 7102/1 Furnace Brazing with Heat Resistant Alloys BAC WLD 7110, 7110/2 Flashwelding of Steel BAC HT 7102/1 Copper Brazing of Steel BAC WLD 7110, 7110/1 Silver Brazing of Steel Copper Nickel Cobalt Alloys Torch Induction BAC A HT 7102/1, 7110/1 Silver Brazing of Steel Copper Nickel Cobalt Alloys Furnace Dip BAC WLD 7110, 7110/1 Aluminum Brazing of Aluminum Torch BAC A HT 7102/1 Aluminum Brazing of Aluminum Furnace Dip BAC HT 7102/5, 7101/5 Optional Temper Inspection of Non ferrous Alloys (Only applies to BAC 5602) BAC SE 7117 Glass Bead Peening BAC WLD 7110, 7110/7 Inertia Friction Welding BAC NDT 7114/3,7114/3S NDI of Adhesive Bonds BAC WLD 7110/13 Fusion Welding of Girth Joints in Systems Tubing BAC WLD 7110/13 Fusion Welding Steel Alloys BAC WLD 7110/13 Fusion Welding CRES Heat Resist Nickel Cobalt Alloys BAC WLD 7110/13 Fusion Welding Aluminum Alloys BAC WLD 7110/13 Fusion Welding Magnesium Alloys BAC WLD 7110/13 Fusion Welding Titanium Titanium Alloys BAC WLD 7110, 7110/3, 7110/6, 7110/12, 7110/13 Electron Beam and Laser Welding BAC WLD 7110, 7110/4 Resistance Welding Steel Alloys BAC WLD 7110, 7110/4 Resistance Welding Ni. Co. Base Alloys BAC WLD 7110, 7110/4 Resistance Welding Aluminum Alloys BAC WLD 7110, 7110/4 Resistance Welding Magnesium Alloys BAC WLD 7110, 7110/4 Resistance Welding Titanium Alloys BAC NDT 7114/3,7114/3S Nondestructive Inspection of Composite Parts Structures BAC COMP 7118 PAR & CP ing for Vacuum Bag Only/Autoclave Cure Epoxy Polymer Matrix Composite, including Sandwich Structures BAC A HT 7102/5, 7101/5 Optional Hardness Testing BAC A CP 7108 Nickel Plating Type III Class 1 Immersion Plating (QPL) BAC B CP 7108 Nickel Plating Type III Class 2 Cup Plating (QPL) BAC A HT 7102/1 BRAZING OF HEAT RESISTANT HONEYCOMB STRUCTURES BMS D COMP 7122, 7124 Structural Adhesives for 180 F Service Applications (QPL) BMS B COMP 7122, 7124 Structural Adhesives for Composite Application 250 F Cure (QPL) BMS C COMP 7122, 7124 Adhesive for Composite Bonding (350 F Cure) (QPL) BMS G COMP 7122, 7124 Adhesives for Primary Structure Composite (QPL) BMS B COMP 7122, 7124 Structural Adhesives for Metal to Sandwich Assemblies FM 61 System (QPL) BMS A COMP 7122, 7124 Polyimide Paste Adhesives (QPL) BMS A COMP 7122, 7124 Foaming Adhesives (QPL) Page 4 of 14 9/19/2017

5 Commodity BMS B COMP 7122, 7124 Fire Resistant Epoxy Resin Preimpreg. Glass Fabrics for General Purpose Use (QPL) BMS C COMP 7122, 7124 Glass Fabric Preimpreg. High Temperature Resistance Epoxy Resin (QPL) BMS A COMP 7122, 7124 Nomex Paper and Glass Fabric Resin Impreg. for Interior Decorative Laminates (QPL) BMS A COMP 7122, 7124 Polyimide Resin Impregnated Structural Fiberglass Fabric (QPL) BMS D COMP 7122, 7124 High Temperature Resistant Epoxy Adhesive Film Glass Fabric Reinforced Plastic Sandwich Assemblies (QPL) BMS D COMP 7122, 7124 Epoxy Preimpreg. Glass Fabric for Interior Sandwich Panels / Laminates / Elec (QPL) BMS E COMP 7122, 7124 High Strength Glass Fabric Preimpreg. High Temp Resistant Epoxy Resin (QPL) BMS A COMP 7122, 7124 Epoxy Preimpreg. Graphite Tapes and Woven Fabrics 250 F (121C) Cure (QPL) BMS E COMP 7122, 7124 Auxiliary Resins for Use with Single Stage Interior Sandwich Panels (QPL) BMS B COMP 7122, 7124 Epoxy Preimpreg. Carbon Fiber Tapes and Woven Fabrics 350 F (177C) Cure (QPL) BMS A COMP 7122, 7124 Aramid Fabrics Preimpregnated With Epoxy Resin (350 F Curing) (QPL) BMS B COMP 7122, 7124 Aramid Fabrics Preimpregnated With Epoxy Resin (250 F Curing) (QPL) BMS A COMP 7122, 7124 Glass Fabric Preimpreg. Modified Phenolic Resin for Crush Core Sandwich Panels (QPL) BMS B COMP 7122, 7124 Modified Phenolic Preimpreg. Glass Fabric for Int. Sandwich Panel and Laminate (QPL) BMS C COMP 7122, 7124 Epoxy Preimpregnated Carbon Fiber Tapes and Woven Fabrics 350 F (177 C Cure) (QPL) BMS D COMP 7122, 7124 Epoxy Preimpreg. Graphite Woven Fabrics 275 F (135C) Cure Vacuum Bag (QPL) BMS C COMP 7122, 7124 Aramid Fabrics Epoxy Resin Impreg. for Int. Sandwich Panels and Laminates (QPL) BMS D COMP 7122, 7124 Aramid Fabrics Preimpregnated With Epoxy Resin for Vacuum Bag (QPL) BMS A COMP 7122, 7124 Carbon Fiber/Phenolic Prepreg. for Interior Sandwich Panels (QPL) BMS E COMP 7122, 7124 Advanced Composites 350 F Cure Toughened Epoxy Preimpreg Carbon Fiber Tapes Fab (QPL) BMS F COMP 7122, 7124 Aluminum Coated Glass Fiber Cloth Epoxy Resin Preimpregnated (QPL) BMS F COMP 7122, 7124 Epoxy Preimpregnated Carbon Tape and Woven Fabric for Aircraft Structure 350 F Cure (QPL) BMS A COMP 7122, 7124 Bismaleimide Roving for Filament Winding (QPL) BMS G COMP 7122, 7124 Advanced Composites 350 F Cure Epoxy Preimpregnated Fiberglass Fabrics (QPL) BMS F COMP 7122, 7124 Surfacing Films for Composites (QPL) BMS A COMP 7122, 7124 Glass Fabric Preimpregnated Epoxy Resin Low Temperature Curing (QPL) BMS A COMP 7122, 7124 Fire Resistant Polyester Resin Preimpreg Glass Fabrics for General Purpose Use (QPL) BMS B COMP 7122, 7124 Epoxy Preimpregnated Peel Ply for Surface Preparation of Composites BSPS B CP 7108/3 Application of Sol Gel Coating for Titanium Bonding BSPS C CP 7108/1 Application of Sol Gel Coating for Titanium Painting BSS A NDT 7114/1,7114/1S Liquid Penetrant Inspection BSS A NDT 7114/2,7114/2S Magnetic Particle Inspection BSS NDT 7114/1,7114/1S Radiologic Inspection/Radiography (film) BSS A NDT 7114/3,7114/3S Ultrasonic Inspection/Longitudinal BSS B NDT 7114/3,7114/3S Ultrasonic Inspection/Shear Wave BSS A NDT 7114/3,7114/3S Ultrasonic Inspection/Plate Flat BSS B NDT 7114/3,7114/3S Ultrasonic Inspection/Round Shapes BSS C WLD 7110/3, 7110/5, 7110/6, 7110/12, 7110/13 Personnel Certification for Visual Weld Inspectors/Examiners Chem. Testing 809 CP 7108/4 Solution Control D027Z COMP 7118 PAR for Manufacture of Composite Parts using Priform(R) by Vacuum Assisted Resin Infusion ing (QPL) D HT 7102/3 Carburizing of Steel D CP 7108 HAE Anodic Treatment of Magnesium Alloys Type I D HT 7102/3 Carburizing of Steel D COMP 7118 PAR & CP BV Doc. for Adv. Comp. (QPL) D COMP 7118 PAR & CP General Req. for Adhesive Bonding Composite Fab. Boeing Helicopters only (QPL) D A CP 7108 Dow 17 Anodizing of Magnesium Alloys DOD P CP 7108 Phosphate Conversion Coating on Steel Page 5 of 14 9/19/2017

6 Commodity DPS L306C CP 7108 Boric Acid Sulfuric Acid Anodizing DPS1.05 L806B HT 7102/5, 7101/5 Optional Hardness Testing of Metals DPS L806A HT 7102/5, 7101/5 Optional Eddy Current Conductivity Testing Equipment & Procedures DPS1.624 L706 COMP 7118 PAR Autoclave ing of Carbon Epoxy DPS1.630 L713 COMP 7118 PAR Resin Film Infusion DPS1.631 L714 COMP 7118 LRP Controlled Atmospheric Pressure Resin Infusion (CAPRI) DPS1.632 L715 COMP 7118 LRP Resin Transfer Molding (RTM) of Fiber Reinforced Parts DPS1.650 L707 COMP 7118 PAR Laminate Fabrication Aramid Fiber Base / Plastic DPS L708 COMP 7118 PAR Laminate Fabrication Composite Assys (DC 9/80) DPS1.660 L709 COMP 7118 PAR,7118 CP Laminate Fabric. Composite Assys Syntactic Core MD 80 DPS L710 COMP 7118 PAR Laminate Fabrication PMR 15 Polymide/Carbon DPS L711 COMP 7118 PAR Laminate Fabrication Bismaleimide/Carbon DPS L712 COMP 7118 PAR Laminate Fabrication Reinforced Bismaleimide DPS1.950 L701 COMP 7118 MB Adhesive Bonding Metal / Metal DPS1.960 L702 COMP 7118 PAR Adhesive Bonding Composite Structure DPS1.964 L703 COMP 7118 PAR Structural Bonding Elevated Cryogenic Temperatures DPS1.967 L704 COMP 7118 MB,7118 CP Adhesive Bonding Composite Assys (DC 9/80) DPS1.99 L705 COMP 7118 MB Adhesive Bonding Metal Face Assys DPS L204 WLD 7110/13 Fusion Weld DPS L812 WLD 7110/3, 7110/5, 7110/6, 7110/12, 7110/13 Qualification of Fusion Welders & Welding Operators DPS L205 WLD 7110/13 Orbital Tube Welding DPS L248 WLD 7110, 7110/3, 7110/12, 7110/13 Electron Beam Welding DPS L203 WLD 7110/13 Fusion Weld Repair Casting DPS L240 WLD 7110, 7110/2 Flash Welding Steel DPS L241 WLD 7110, 7110/2 Flash Welding Rings DPS L242 WLD 7110, 7110/2 Resistance Flash Welding Aluminum DPS L272 WLD 7110, 7110/9 Capacitor Discharge Stud Welding DPS L271 WLD 7110, 7110/7 Inertia Welding DPS L220 WLD 7110, 7110/4 Resistance Welding Spot Seam DPS L253 WLD 7110, 7110/1 Brazing Aluminum Torch DPS L253A HT 7102/1 Brazing Aluminum Dip DPS L251 WLD 7110, 7110/1 Brazing Steel / Nickel / Copper Torch Induction DPS L251A HT 7102/1 Brazing Steel / Nickel / Copper Furnace DPS L254 WLD 7110, 7110/1 Brazing Tube Joints Automatic DPS L254A WLD 7110, 7110/1 Brazing High Stregnth Tube Joints Automatic DPS L254B WLD 7110, 7110/1 Brazing Flex Titanium Tube Joints Automatic DPS L254C WLD 7110 Brazing Tube RF Induction Gage Measurements DPS L254D WLD 7110, 7110/1 Brazing Titanium Tube Joints Automatic DPS L255 HT 7102/1 Brazing Honeycomb Assemblies DPS L255A HT 7102/1 Vacuum Brazing Inconel 625 Honeycomb Assemblies DPS11.01 L304 CP 7108 Chromic Acid Anodizing DPS L304A CP 7108/3 Chromic Acid Anodizing Metal Adhesive Bonding DPS L304B CP 7108 Chromic Acid Anodizing Chromate Sealed DPS11.04 L308 CP 7108 Hard Anodizing Aluminum DPS11.05 L306 CP 7108 Sulfuric Acid Anodizing DPS L306A CP 7108 Sulfuric Acid Anodizing Controlled Thickness DPS L306B CP 7108 Sulfuric Acid Anodizing Thin Film DPS11.06 L313 CP 7108 Color Anodizing DPS11.08 L542 CP 7108/3 Phosphoric Acid Anodizing DPS3.694 L501A SE 7117 Peen Forming Aluminum DPS3.695 L501B SE 7117 Peen Forming Honeycomb DPS L392A CP 7108/1 Fuel Tank Coating manual touch up excluded for requiring approval DPS4.704 L400 NDT 7114/2,7114/2S Magnetic Particle Inspection DPS4.706 L424 NDT 7114/4,7114/4S Radiographic Inspection Castings DPS4.707 L410 NDT 7114/1,7114/1S Penetrant Inspection DPS4.713 L430 NDT 7114/3,7114/3S Ultrasonic Inspection Wrought Metals DPS4.715 L441 CP 7108/2 Etch Inspection Machined / Ground Steel DPS4.736 L421 NDT 7114/4,7114/4S Radiographic Inspection DPS L430B NDT 7114/3,7114/3S Ultrasonic Inspection Composite Structures DPS L425 NDT 7114/4,7114/4S Radiographic Inspection Composite Structures Page 6 of 14 9/19/2017

7 Commodity DPS L430C NDT 7114/3,7114/3S Ultrasonic Inspection Metal Bonded Sandwich DPS4.999 L500 SE 7117 Shot Peening Metal Parts DPS L101E HT 7102 HT Steel Martensitic Stainless DPS HI L101G HT 7102 HT Steel Vacuum (> 220 KSI) DPS LO L101F HT 7102 HT Steel Vacuum (< 220 KSI) DPS5.00 1HI L101B HT 7102 HT Steel (> 260 KSI) Does NOT apply when referenced to DPS9.74 DPS5.00 1LO L101A HT 7102 HT Steel (< 260 KSI) Does NOT apply when referenced to DPS9.74 DPS L101C HT 7102 HT Steel Precipitation Hardenable Does NOT apply when referenced to DPS9.74 DPS L171 HT 7102 Case Hardening Nitriding DPS L161 HT 7102 Case Hardening Carburizing DPS L165 HT 7102 Case Hardening Induction DPS L101D HT 7102 HT Steel Stainless Strain Hardenable DPS5.08 L121 HT 7102 HT Beryllium Copper DPS6.30 L141 HT 7102 HT Super Alloy DPS6.33 L151 HT 7102 HT Titanium DPS L111A HT 7102 HT Aluminum Wrought Materials DPS T111A HT 7102/2 Aluminum Heat Treatment Procedures C17 DPS L111B HT 7102 HT Aluminum Rivets DPS L111C HT 7102 HT Aluminum Local OverAging 7075 T73 DPS9.28 L341 CP 7108 Cadmium Plating High Strength Steel DPS L341A CP 7108 Cadmium Plating High Strength Steel Post Chromate Treat. DPS9.45 L322 CP 7108 Coating Colorless Chemical Surface Treatment of Aluminum Alloys (Immersion Application Only) DPS9.45 L325 CP 7108 Coating Multicolored Chemical Surface Treatment of Aluminum Alloys (Immersion Application Only) DPS9.481 L532 CP 7108 Chemical Milling Aluminum DPS9.482 L537 CP 7108 Chemical Milling Requirements Low Alloy Steels DPS9.483 L530 CP 7108 Chemical Milling Titanium DPS9.484 L531 CP 7108 Chemical Milling Corrosion Resistant Steel DPS9.485 L534 CP 7108 Chemical Milling Nickel DPS9.67 L364 CP 7108 Electroless Nickel Plating DPS9.69 L356 CP 7108 Copper Plating DPS9.71 L351 CP 7108 Chromium Plating DPS L363 CP 7108 Nickel Plating Sulfamate DPS9.84 L354 CP 7108 Chromium Plating Thin Dense DPS9.86 L368 CP 7108 Tin Plating DPS9.89 L347 CP 7108 Brush Plating DPS L347A CP 7108 Brush Nickel Plating ES 5 37 R248A WLD 7110, 7110/3, 7110/12, 7110/13 Electron Beam Welding GA R532 CP 7108 Chem Milling Aluminum Alloys SMPP Rqd GA R192 HT 7102 Surface Hardening Carbon Alloy Steel HBPS H712 COMP HBPS H205A WLD HBPS H200 WLD 7118 PAR & CP, (CP only with F4 Limitation, PAR only with F10 Limitation) Laminate, Sandwich Constructions, High Temperature Bismaleimide Composite, 375/440F Cure, Fabrication of 7110/13 Orbital Tube Welding CRES Titanium and Nickel Alloys 7110/13 Fusion Welding for Space Systems HBPS H443 NDT 7114/3,7114/3S Ultrasonic Inspection of Composite Laminates Structures and Honeycomb Assemblies HBPS H444 NDT 7114/3,7114/3S Sonic and Ultrasonic Resonance Inspection of Bonded Assemblies HBPS H421D NDT 7114/4 Radiographic Inspection of Composites HP1 1 M101A HT 7102 HT Steel HP11 1 M204 WLD 7110/13 Fusion Welding HP11 21 M203A WLD 7110/13 Fusion Weld Repair Aluminum Magnesium Castings HP11 22 M203B WLD 7110/13 Fusion Weld Repair Steel Castings HP11 25 M271 WLD 7110, 7110/7 Inertia Welding Metals HP11 27 M203C WLD 7110/13 Fusion Weld Repair Titanium Castings HP11 28 M203D WLD 7110/13 Fusion Weld Repair Copper Castings HP11 3 M220 WLD 7110, 7110/4 Welding Spot / Seam / Projection Page 7 of 14 9/19/2017

8 Commodity HP11 31 M250A HT 7102/1 Furnace Brazing (Excluding Aluminum Alloys) Type II HP11 31 M251C WLD 7110/1 Torch Brazing (Using Silver Brazing Alloys Only) Type I HP11 31 M253A HT 7102/1 Dip Brazing (Aluminum Alloys Only) Type V HP11 31 M255A WLD 7110/1 Induction Brazing (Excluding Aluminum Alloys) Type III HP11 8 M248 WLD 7110/3 Electron Beam Welding HP1 18 M151 HT 7102 HT Titanium HP1 2 M111A HT 7102 HT Aluminum HP1 20 M181 HT 7102 HT Magnesium HP1 25 M141 HT 7102 Heat Treatment of Nickel and Cobalt Alloys (QPL) HP1 3 M121 HT 7102 HT Beryllium Copper HP15 42 M716 COMP 7118 PAR Laminate Fabricaiton Reinforced Composites HP15 90 M718 COMP 7118 PAR Composite Fabrication Autoclave / Pressure Cure HP15 96 M707 COMP 7118 PAR,7118 CP Bonding Honeycomb Nonmetallic Core HP16 21 M708 COMP 7118 MB Structural Bonding Metal / Metal HP16 30 M710 COMP 7118 MB,7118 CP Structural Bonding High Strength Metals Nonmetallic HP18 14 M713 COMP 7118 PAR Structural Bonding Syntactic Foam HP18 15 M714 COMP 7118 PAR Fabrication Core Closed Cell Rigid Polyvinyl Foams HP18 4 M531 CP 7108 Chemical Milling HP2 11 M161A HT 7102 Carburizing Steel Transmission Gears HP2 12 M161B HT 7102 Carburizing and Heat Treat of Steel, UNSK71040 (QPL) HP2 2 M161 HT 7102 Carburizing Steel HP2 3 M171 HT 7102/4 Nitriding Steel HP2 4 M165 HT 7102 Induction Hardening Steel HP2 9 M171A HT 7102/4 Nitriding Steel (AH 64A Only) HP30 4 M441 CP 7108/2 Etching For Detection Of Grinding Burns HP4 10 M364 CP 7108 Electroless Nickel Plating HP4 100 M702 CP 7108/3 Adhesive Primer Control HP4 11 M341 CP 7108 Cadmium Plating HP4 113 M347 CP 7108 Brush Plating HP4 12 M349 CP 7108 Zinc Plating HP4 120 M703A CP 7108 Bonding Preparation Titanium HP4 121 M703B CP 7108/3 Bonding Preparation AM 355 Stainless Steel HP4 124 M307 CP 7108 Anodizing Titanium HP4 125 M344 CP 7108 Cadmium Titanium Plating HP4 13 M351 CP 7108 Chromium Plating HP4 136 M323 CP 7108/1 Preparation of Metallic Materials for Adhesive Bonding using Sol Gel HP4 137 M542 CP 7108/3 Phosphoric Acid Anodizing of Aluminum for Structural Bonding HP4 14 M368 CP 7108 Tin Plating HP4 17 M335 CP 7108 Silver Plating HP4 18 M357 CP 7108 Gold Plating HP4 2 M304 CP 7108 Anodizing Aluminum HP4 35 M305 CP 7108 Anodizing Aluminum Metal to Metal Bonding HP4 36 M500 SE 7117 Shot Glass Bead Peening Metal Parts HP4 49 M701 CP 7108/3 Adhesive Bonding Nickel / Stainless Steel HP4 50 M384 CP 7108 Chemical Blackening Ferrous Metals HP4 57 M325 CP 7108 Chemical Film Aluminum (Immersion Application Only) HP4 60 M361 CP 7108 Nickel Electrodeposited HP4 62 M356 CP 7108 Copper Plating HP4 68 M319 CP 7108 Flourocarbon Impregnation Inorganic Coatings HP4 7 M332A CP 7108 Manganese Zinc Phosphate Coatings for Ferrous Metals HP4 79 M308 CP 7108 Anodizing Aluminum Wear Resistance HP4 9 M324 CP 7108 Corrosion Protection Magnesium not required for Type VII HP4 90 M365 CP 7108 Electroless Nickel / PTFE Plating HP6 13 M410A NDT 7114/1,7114/1S Penetrant Inspection Fluorescent HP6 18 M424 NDT 7114/4 Radiographic Inspection HP6 19 M806B HT 7102/5, 7101/5 Optional Hardness Testing of Metals HP6 22 M430 NDT 7114/3,7114/3S Ultrasonic Inspection Metals HP6 35 M806A HT 7102/5, 7101/5 Optional Heat Treat Temper Inspection of Aluminum Alloys Conductivity Inspection (QPL) HP6 46 M444 NDT 7114/3,7114/3S Ultrasonic Inspection Composites HP6 47 M425 NDT 7114/4 Radiographic Inspection Composite Structures HP6 48 M466 NDT 7114/3,7114/3S Resonance Inspection Composite Structures HP6 5 M400 NDT 7114/2,7114/2S Magnetic Particle Inspection HP9 20 M703C CP 7108/3 Bonding Preparation Tungsten LA U133 HT 7102 Limitation For ing PH Steel Details LA U103 HT 7102 Limit. Straightening HT Carbon/Alloy/400 Series Steel Parts Page 8 of 14 9/19/2017

9 Commodity LA U530 CP 7108 Chemical Milling of Titanium Alloys SMPP Req d LA U536A CP 7108 Chem Mill ing of Magnesium Alloys LA U537A CP 7108 Chem Milling of Ferrous Nickel Base Alloys SMPP Req d LA U733 COMP 7118 PAR Fabrication of Temperature Resistant Advanced Comp. LA U729 COMP 7118 PAR Fab Solid Graphite Reinf Epox Lam Substr Parts 67 >350 F LA U540A COMP 7118 MB Structural Adhesive Bonding at Room Temperature LA U250 HT 7102/1 Copper Furnace Brazing of Steel LA U251 WLD 7110, 7110/1 Low Temp Silver Brazing of Steels Copper Copper Alloys Torch Induction LA U251A HT 7110, 7110/1 Low Temp Silver Brazing of Steels Copper Copper Alloys Dip LA U220 WLD 7110, 7110/4 Resistance Weld Spot Seam Stitch All Welds Cl A LA U255 HT 7102/1 Furnace Brazing H 11 Steel 440C Cor. Resistant Steel LA U254 HT 7102/1 Furnace Brazing of Cres Steel LA U252 WLD 7110/13 Fusion Weld Sealing of 9NI 4CO 30C SMPP Req d LA U214A WLD 7110/13 Fusion Weld Seal 6A1 4V Ti Hydr. Components SMPP Req d LA U216A WLD 7110/13 Fusion Weld Magnetic Alloy (LB ) SMPP Req d LA U202A WLD 7110/13 Fusion Weld Heat Resistant Alloys SMPP Req d LA U313 CP 7108 Anodizing and Coloring of Aluminum Alloys LA U351 CP 7108 Hard Chromium Plating SMPP Req d LA U326 CP 7108 Chemically Film Treatment for Ti and Ti Alloys SMPP LA U360 CP 7108 Nickel Tin Coating of Alloy Steel SMPP Req d LA U165 HT 7102 Surface Hardening of Carbon Alloy Steel LA U101A HT 7102 Heat Treatment of Carbon and Alloy Steels LA U151 HT 7102 Heat Treatment of Ti Alloy Bar Forgings And Extrusions LA U101B HT 7102 ing Steel Parts Heat Treated to Hi. Tensile Strength LA U121 HT 7102 Heat Treatment of Copper and Copper Alloys LA U101C HT 7102 Heat Treat ing of Ultra Hi. Strength Steel Alloy LA U101E HT 7102 ing H T of Tool Steels for Airframe Use LA U101F HT 7102 Surface Hardening of Stainless Steels by Malcomizing SMPP LA U101G HT 7102 Heat Treatment of 18 NI Mar Aging Steel LA U151A HT 7102 Heat Treatment of Titanium Alloys LA U141A HT 7102 Heat Treat of Heat Resist Fe Cobalt Base Alloys SMPP Req d LA U105A HT 7102 Heat Treatment of Nickel Base Magnetic Alloys SMPP Req d LA U101H HT 7102 Heat Treatment of 400 Series Steels LA U153 HT 7102 HT Diffusion Bonded Ti. Base 6ENT Vanadium SMPP Req d LA U390B CP 7108/1 Lubricant/Dry Film/Resin/Bonded/Graphite Free Appl of SMPP LA U392B CP 7108/1 Appli. of Corro Prevent Finish for Elec Bonding SMPP Req d LA U203 WLD 7110/13 Casting In Repair Welding SMPP Req d LA U166 HT 7102 Autoclave Form. Concur.Precip. HT B1 B Wing Outer Pnls SMPP LA U722 COMP 7118 PAR,7118 CP Fabrication Graphite/Epoxy Flaps for B1 B LA U723A COMP 7118 PAR,7118 CP Fab Fairing Pnls Cocure Graph/Epx Fibergl Graph/Epx HybHC LA U723B COMP 7118 PAR,7118 CP Fab Cocured Graphite/Epoxy SW B1 B Weapons Bay Door Assy Mech. Testing 802 MTL 7101/1 & /3 Mechanical Testing Metallic Met. Testing 803 MTL 7101/1 & /4 Metallurgical Testing MIL A CP 7108 Chromic Acid Anodizing of Alum. Type I MIL A D CP 7108 Anodize Aluminum Type Ic Boric Sulfuric Anodize MIL A CP 7108 Sulfuric Acid Anodize Type II (Approval Not Required for International Space Station (ISS) Houston Only) MIL A B CP 7108 Anodize Type IIb Boric Sulfuric Anodize MIL A CP 7108 Hard Anodize Type III MIL B WLD 7110, 7110/1 Brazing of Steel Copper Nickel Aluminum Torch Induction MIL B G HT 7102/1 Brazing of Steel Copper Nickel Aluminum Furnace Dip MIL C CP 7108 Black Oxide Conversion Coating on Steel MIL C CP 7108 Copper Plating MIL C CP 7108 Electroless Nickel Coatings MIL C CP 7108 Chemical Conversion Coating on Aluminum (Immersion App only) (Approval Not Required for International Space Station (ISS) Houston Only) MIL DTL B CP 7108 Phosphate Coating Heavy Manganese or Zinc Base MIL DTL N371C CP 7108 Gold Plating, Electrodeposited MIL DTL B CP 7108 Chemical Conversion Coatings on Aluminum and Aluminum Alloys (Immersion Application Only) MIL G N371 CP 7108 Gold Plating/Electrodeposited (Approval Required for NASA Space Shuttle and IDS Anaheim Only) MIL H HT 7102/2 Heat Treat of Aluminum Alloys Page 9 of 14 9/19/2017

10 Commodity MIL H HT 7102 Heat Treat of Alloy Steels MIL H HT 7102 Heat Treat of Corrosion Resistant Steel MIL H HT 7102 Heat Treat of Copper/Beryllium Alloys MIL H HT 7102 Heat Treat of Titanium and Ti. Alloys MIL I NDT 7114/1,7114/1S Penetrant Inspection MIL I NDT 7114/2,7114/2S Magnetic Particle Inspection MIL I C NDT 7114/3,7114/3S Ultrasonic Inspection of Flat Surface Shapes MIL I B NDT 7114/3,7114/3S Ultrasonic Inspection of Rounds and Shapes Req d Compensation MIL M CP 7108 Conversion Coating on Magnesium Type III (Dow 7) MIL M CP 7108 Anodizing of Magnesium (HAE ) MIL M CP 7108 Anodizing of Magnesium (Dow 17 ) MIL M HT 7102 Heat Treat of Magnesium MIL P A CP 7108 Phosphate Coatings Heavy Manganese or Zinc Base (for Ferrous Metals) MIL P A CP 7108 Tin Lead Electroplate MIL R CP 7108 Rhodium Plating Electrodeposited MIL R SE 7117 Rotary Flap Peening of Metal Parts MIL S SE 7117 Shot Peening MIL S HT 7102/3 Carburizing of Steel MIL S HT 7102/4 Nitriding of Steel MIL STD F HT 7102/5, 7101/5 Optional Test Method Standard for Electrical Conductivity Test for Verification of Heat Treatment of Aluminum Alloys Eddy Current Method MIL STD NDT 7114/2,7114/2S Magnetic Particle Inspection MIL STD NDT 7114/3,7114/3S Ultrasonic Inspection of Flat Surface Shapes MIL STD NDT 7114/3,7114/3S Ultrasonic Inspection of Rounds Shapes Req d Compensation MIL STD WLD 7110/13 Fusion Welding for A/S App Steel CRES Heat Resist Alloys MIL STD WLD 7110/13 Fusion Welding for Aerospace Applications Aluminum Alloys MIL STD WLD 7110/13 Fusion Welding for Aerospace Applications Magnesium Alloys MIL STD A WLD 7110/13 Fusion Welding for Aerospace Applications Titanium Alloys MIL STD NDT 7114/1,7114/1S Radiographic Inspection MIL STD NDT 7114/1,7114/1S Penetrant Inspection MIL STD A SE 7117 Glass Bead Peening MIL STD 865 N372 CP 7108 Brush Plating/Electrodeposited (Approval Required for NASA Space Shuttle and IDS Anaheim Only) MIL T CP 7108 Tin Plating Types I and II MIL W C WLD 7110/3 Electron Beam Welding for Fatigue Critical Application MIL W D WLD 7110/3 Electron Beam Welding MIL W WLD 7110, 7110/4 Resistance Welding Steel Alloys MIL W WLD 7110, 7110/4 Resistance Welding Ni. Co. Base Alloys MIL W WLD 7110, 7110/4 Resistance Welding Aluminum Alloys MIL W WLD 7110, 7110/4 Resistance Welding Magnesium Alloys MIL W WLD 7110, 7110/4 Resistance Welding Titanium Alloys MIL W WLD 7110, 7110/2 Flash Welding Steel MIL W C WLD 7110/13 Fusion Welding for Aerospace Applications Aluminum Alloys MPD2019 H101 HT 7102 Cold Treatment for Metals MS HT 7102/4 Nitriding of Steel MS CP 7108 Black Oxide Steel Conversion Coating MSFC SPEC 469 R152 HT 7102 Titamium Ti Alloys Heat Treatment of SMPP Rqd NAS A NDT 7114,7114S NDI Personnel Certification Level 3 Magnetic NAS A NDT 7114,7114S NDI Personnel Certification Level 3 Penetrant NAS A NDT 7114,7114S NDI Personnel Certification Level 3 Radiographic NAS A NDT 7114,7114S NDI Personnel Certification Level 3 Ultrasonic NAS824 H430A NDT 7114/3,7114/3S Ultrasonic Inspection Wrought Metals PRC 0001 H210D WLD 7110/13 for the Manual Arc Welding of Aluminum Alloy Hardware (ISS Support Only) PRO 14 R248B WLD 7110, 7110/3, 7110/12, 7110/13 Electron Beam Welding SMPP Rqd PS12035 S542 CP 7108/3 Cleaning of Aluminum Detail Parts for Adhesive Bonding PS12037 S510 CP 7108/3 Cleaning of Titanium Detail Parts for Adhesive Bonding PS13025 S368 CP 7108 Tin Plating PS13055 S375A CP 7108 Silver Plating 17 4 PH Steel PS13101 S341 CP 7108 Cadmium Plating PS13102 S351 CP 7108 Chromium Plating PS13104 S356 CP 7108 Copper Plating Page 10 of 14 9/19/2017

11 Commodity PS13105 S364 CP 7108 Electroless Nickel Plating PS13107 S365 CP 7108 Plating Diffused Nickel Cadmium PS13108 S375 CP 7108 Silver Plating PS13112 S361 CP 7108 Nickel Plating PS13113 S347 CP 7108 Brush Plating PS13144 S348 CP 7108 Cadmium Plating Low Embrittlement PS13201 S304 CP 7108 Anodizing Aluminum PS S304A CP 7108 Black Anodizing Aluminum PS13202 S322 CP 7108 Coatings Colorless Chemical Surface Treatment of Aluminum Alloys (Immersion Application Only) PS13208 S306 CP 7108 Hard Coat Aluminum PS13209 S325 CP 7108 Coating Multicolored Chemical Conversion of Aluminum Alloys by Immersion PS14023 S500 SE 7117 Peening PS14034 S719 COMP 7118 PAR Laminate Fabrication Plastic PS S720 COMP 7118 PAR Laminate Fabrication Non Structural Plastic PS S721 COMP 7118 PAR Fabrication Plastic Pressure Ducts PS S722 COMP 7118 PAR Laminate Fabrication Glass Fabric/Reinforced Bismaleimide PS14057 S723 COMP 7118 PAR Fabrication Duct Assembly PS14059 S724 COMP 7118 PAR Laminate Fabrication Silicone Rubber Plastic PS14062 S702 COMP 7118 CP Fabrication Impregnated Paper Core Honeycomb Assys PS14081 S703 COMP 7118 PAR,7118 CP Fabrication Aluminum Honeycomb / Boron Skin PS14094 S501 SE 7117 Peen Forming PS14120 S704 COMP 7118 PAR,7118 CP Fabrication Aluminum Honeycomb / Boron Skin / Fiberglass PS14123 S705 COMP 7118 PAR,7118 CP Fabrication Honeycomb Core / Glass Epoxy Skin PS14124 S706 COMP 7118 PAR,7118 CP Fabrication Aluminum Honeycomb / Graphite Skin PS14130 S707 COMP 7118 PAR Laminate Fabrication Boron / Epoxy PS14196 S712A COMP 7118 PAR Carbon Epoxy Structural Skin Fab and Acceptance of PS14197 S712B COMP 7118 PAR & CP Carbon Epoxy Structural Skins Al Honeycomb Core Fab and Acceptance of PS14198 S706A COMP 7118 PAR,7118 CP Carbon Epoxy Structural Skins Al Honeycomb Core Fiber Glass Fab and Acceptance PS14214 S709 COMP 7118 MB Fabrication Aluminum Sandwich Assemblies PS14223 S710 COMP 7118 MB Fabrication Aluminum Sandwich Assemblies PS14240 S711 COMP 7118 PAR Laminate Fabrication Graphite PS14247 S711A COMP AC7118 PAR CARBON FIBER BISMALEIMIDE LAMINATES, FABRICATION AND ACCEPTANCE OF PS14250 S713A COMP 7118 PAR & CP Low Temp Cure Epoxy Laminates and Sandwich Structures (Non Autoclave Cure) Fab and Acceptance of PS14257 S723A COMP 7118 PAR & CP Polyimide Laminates and Sandwich Structures PS14261 S712C COMP 7118 PAR Carbon Fiber Reinforced Toughened Epoxy Laminates (Low Rate Production) fab of PS14268 S712 COMP 7118 PAR Laminate Fabrication Carbon Fiber / Epoxy PS14269 S713 COMP 7118 PAR Laminate Fabrication Carbon / Epoxy PS14270 S722C COMP 7118 PAR Carbon Fiber Reinforced Bismaleimide Laminates (Low Rate Production) Fab and Acceptance of PS14274 S714 COMP 7118 LRP Fabrication Resin Transfer Molded Composites PS14302 S715 COMP 7118 PAR Adhesive Bonding Composite Structures PS14340 S716 COMP 7118 PAR Fabrication Carbon / Epoxy Horizontal Stab. Rudder PS14605 S714A COMP 7118 LRP Vacuum Assisted Resin Transfer Molding (VARTM) of Composite Laminates and Sandwich Assemblies PS14998 S706B COMP 7118 PAR,7118 CP Co bonded and Co cured Carbon Epoxy Honeycomb Core Structure PS14999 S718 COMP 7118 CP Bonding Graphite / Aluminum PS S101H HT 7102 HT Hardening Martensitic Stainless Steels to KSI PS S101J HT 7102 HT Hardening PH Grade Stainless Steel to H Condition PS S101K HT 7102 HT Hardening PH Gr Stainless Steel to CH900/CA 850 Condition PS S101L HT 7102 HT Hardening PH Grade Stainless Steel to RH Condition PS S101M HT 7102 HT Hardening PH Grade Stainless Steel to TH Condition PS S101N HT 7102 HT Steel Annealing PS S101A HT 7102 HT Steel Normalizing PS S101B HT 7102 HT Steel Normalizing & Tempering PS S101C HT 7102 HT Steel Hardening (<= 180 KSI) PS S101D HT 7102 HT Steel Hardening (>= 200 KSI) PS S101E HT 7102 HT Steel Martempering 4340 PS S101F HT 7102 HT Steel Martempering 4330V PS S101G HT 7102 HT Steel Annealing Stainless & 18% Ni (Grade 250) PS15149 S103B HT 7102 HT Steel Hardening 440C PS15151 S103C HT 7102 HT Steel Hardening & Cold Stabilization 440C (incl PS15326) PS15154 S103D HT 7102 HT Steel Age Hardening 18% Ni (Grade 250) Maraging Steel Page 11 of 14 9/19/2017

12 Commodity PS15159 S103E HT 7102 HT Steel Vacuum Hardening & Cold Stabilization 440C PS15165 S103F HT 7102 HT Steel HP9Ni 4Co.30C ( KSI) PS15166 S103G HT 7102 HT Steel HP9Ni 4Co.20 ( KSI) PS15167 S103H HT 7102 HT Steel AF1410 PS15169 S103J HT 7102 HT Steel Aermet 100 PS15220 S103K HT 7102 HT Steel High Alloy Stabilization PS15233 S103L HT 7102 HT Steel 17 7PH to TH 1050 Condition PS15296 S103M HT 7102 HT Steel Hardening 300M ( KSI) PS15300 S103N HT 7102 HT Steel Hardening 4340 ( KSI) PS15301 S103P HT 7102 HT Steel Hardening H 11 PS15305 S103R HT 7102 HT Steel Subcritical Annealing 300M PS15325 S103S HT 7102 Vacuum ing of Metals PS15351 S182A HT 7102 HT Steel Hardening 300M (AMS 6419) to KSI PS15352 S182B HT 7102 HT Steel Hardening D6AC to KSI PS15416 S103U HT 7102 HT Steel Martempering AF 1410 PS15451 S171A HT 7102 Case Hardening Nitriding PS15452 S161 HT 7102 Case Hardening Carburizing PS15453 S171B HT 7102 Case Hardening Salt Bath Nitriding PS15500 S111 HT 7102/2 Heat Treating for Aluminum Alloys PS15600 S141 HT 7102 HT Nickel, Cobalt, and Super Alloys PS15800 S151 HT 7102 HT Titanium PS15935 S121 HT 7102 HT Copper Beryllium Alloys PS18021 S391 CP 7108 Application Dry Film Lubricant PS20022 S531 CP 7108 Chemical Milling PS20650 S531A CP 7108 Chemical Blanking PS S531B CP 7108 Chemical Blanking Stainless Steel PS21201 S400 NDT 7114/2,7114/2S Magnetic Particle Inspection PS21202 S410A NDT 7114/1,7114/1S Penetrant Inspection Aluminum PS21202 S410B NDT 7114/1,7114/1S Penetrant Inspection Beryllium PS21202 S410C NDT 7114/1,7114/1S Penetrant Inspection Cobalt Nickel PS21202 S410D NDT 7114/1,7114/1S Penetrant Inspection Copper PS21202 S410E NDT 7114/1,7114/1S Penetrant Inspection Low Alloy Steels PS21202 S410F NDT 7114/1,7114/1S Penetrant Inspection Magnesium PS21202 S410H NDT 7114/1,7114/1S Penetrant Inspection Stainless Steels PS21202 S410J NDT 7114/1,7114/1S Penetrant Inspection Titanium PS21203 S806B HT 7102/5, 7101/5 Optional Hardness Testing of Parts and Materials PS21205 S441 CP 7108/2 Temper Etch Inspection PS21206 S421 NDT 7114/4,7114/4S Radiographic Inspection PS S421A NDT 7114/4,7114/4S Radiographic Inpsection Metallic Honeycomb Assys PS S421C NDT 7114/4,7114/4S Radiographic Inspection Composite Parts PS21207 S806A HT 7102/5, 7101/5 Optional Eddy Current Determination of Electrical Conductivity for Aluminum Alloys PS21211 S430 NDT 7114/3,7114/3S Ultrasonic Inspection PS S430A NDT 7114/3,7114/3S Ultrasonic Inspection Welds PS S430B NDT 7114/3,7114/3S Ultrasonic Inspection Metal Tubing PS S430C NDT 7114/3,7114/3S Ultrasonic Inspection Machined Parts / Thin Mat l PS S430D NDT 7114/3,7114/3S Ultrasonic Inspection Honeycomb / Composites Structure PS S430E NDT 7114/3,7114/3S Ultrasonic Inspection Metal Bond / Brazed Honeycomb PS21244 S466A NDT 7114/3,7114/3S Ultrasonic Resonsance Inspection Honeycomb / Composites PS21406 S421D NDT 7114/4,7114/4S Radiographic Inspection AV 8 Horizontal Stab. Rudder PS21411 S466C NDT 7114/3,7114/3S Ultrasonic Inspection AV8 Horizontal Stab. Rudder PS22000 S220 WLD 7110, 7110/4 Resistance Welding Spot Seam PS22010 S230 WLD 7110, 7110/4 Resistance Welding Aluminum PS22155 S222 WLD 7110, 7110/4 Resistance Welding Stainless Steel Wire PS22162 S205 WLD 7110/5 Automatic Gas Tunsten Arc Welding of Tubular Joints PS22201 S210 WLD 7110/5 Fusion Welding Aluminum PS22240 S214 WLD 7110/5 Fusion Welding Titanium PS22250 S200 WLD 7110/5 Fusion Welding Steel PS22300 S248 WLD 7110, 7110/3, 7110/12, 7110/13 Electron Beam Welding PS22604 S251 WLD 7110, 7110/1 Brazing Steel Torch Induction PS22604 S251A HT 7102/1 Brazing Steel Furnace PS22605 S253 WLD 7110, 7110/1 Brazing Aluminum Torch PS22605 S253A HT 7102/1 Brazing Aluminum Furnace Dip QQ C CP 7108 Chromium Plating QQ N CP 7108 Nickel Plating QQ P CP 7108 Cadmium Plating Types I and II Page 12 of 14 9/19/2017

13 Commodity QQ P CP 7108 Cadmium Plating Type III QQ S CP 7108 Silver Plating Quality System 1 AQS 7004 Boeing approved QMS as defined in or Requirements Sec SCGPS A CP 7108 Low Microwave Resistance Silver Plating (Electrodeposited) SCGPS A CP 7108 Electroless Nickel Plating SCGPS N371B CP 7108 Gold Plating (Electrodeposited) SCGPS COMP 7118 PAR & CP Cocured Honeycomb Sandwiches, Epoxy/Polyamide, Fabrication of SCGPS COMP 7118 PAR Epoxy/Polyamide Laminate, Fabrication of SCGPS COMP 7118 PAR & CP Cocured Honeycomb Sandwiches, Epoxy/Graphite, Fabrication of SCGPS COMP 7118 PAR Epoxy/Graphite Laminates, Fabrication of S F501 S761 COMP 7118 MB (MB not required with F4 Limitation),7118 CP Bonding, Structural Adhesive Sandwich/Laminates Aluminum Alloy S F502 S762 COMP 7118 PAR & CP Fabrication of 250F Curing Epoxy Resin Composites Laminate and Honeycomb Sandwich Parts SPS03510 H304 CP 7108 Anodizing Aluminum SPS H304A CP 7108 Color Anodize Aluminum SPS07040 H210A WLD 7110/13 Fusion Welding Aluminum SPS99008 H410A NDT 7114/1,7114/1S Penetrant Inspection SPS99009 H421A NDT 7114/4,7114/4S Radiographic Inspection ST0106LA0032 U547 COMP 7118 MB,7118 CP Adhesive Bonded Honeycomb Panel SMPP Req d ST0106LA0039 U540B COMP 7118 MB Structural Adhes Bonding Metals Reinforced Plastics SMPP ST0107AA0034 P248 WLD 7110, 7110/3, 7110/12, 7110/13 Qual Rqmts for Electron Beam Welding ST0107AA0036 P216 WLD 7110/13 Fusion Welding of Specialty Materials ST0107AA0052 P217 WLD 7110/13 Repair Welding of Steel Castings:Polaris Poseidon Contract ST0107AA0053 P236 WLD 7110, 7110/4 Resistance Welding of Specialty Materials ST0107AA0065 P210 WLD 7110/13 Fusion Welding of Aluminum Aluminum Alloys ST0107AA0068 P201A WLD 7110/13 Fusion Welding of Nickel Base Alloys ST0107AA0069 P200 WLD 7110/13 Fusion Welding of Carbon Low Alloy Steels ST0107AA0070 P201B WLD 7110/13 Fusion Welding of Corrosion Resistant Steels ST0107LA0012 U216D WLD 7110/13 Fusion Welding Magnetic Alloy (ST0170L0011) ST0107LA0014 U216E WLD 7110, 7110/1 TIG Brazing Magnetic Alloy ST0107LA0017 U214B WLD 7110, 7110/1 Fusion Welding Titanium SMPP Req d ST0107LA0018 U201C WLD 7110/5 Fusion Welding High Strength Steel SMPP Req d ST0107LA0019 U201D WLD 7110/13 Fusion Welding 9NI 4CO 0.20C SMPP Req d ST0107LA0020 U210 WLD 7110/13 Fusion Welding Aluminum Alloys ST0107LA0021 U202B WLD 7110/13 Fusion Welding Corrosion Resistant Steel ST0108LA0011 U914 CP 7108/1 Application of Intregal Fuel Tank Coating ST0109LA0007 U363 CP 7108 Hard Nickel Plating SMPP Req d ST0110LA0007 U514B CP 7108/3 Surface Preparation of Materials for Adhesive Bonding ST0110LA0008 U396 CP 7108 Cleaning Titanium Titanium Alloys SMPP Req d ST0111AA0018 P131A HT 7102 HT Wrought/Non Hard./Austenitic/CRES 300 Series ST0111AA0019 P131B HT 7102 HT Wrought/Hard/Martinsitic Cor. Resist Steels 400 Series ST0111AA0020 P131C HT 7102 HT Wrought Precipitation Hardening Cor. Resist Steels ST0111AA0021 P131D HT 7102 Heat Treatment of Cast Corrosion Resistant Steels ST0111LA0001 U105B HT 7102 Heat Treatment of Magnetic Alloy ST0170LB0011 ST0111LA0002 U141B HT 7102 Heat Treatment of 9NI 4CO Alloy Steel SMPP Req d ST0111LA0003 U151B HT 7102 Heat Treat of Titanium SMPP Req d ST0111LA0005 U101J HT 7102 Heat Treatment Carbon and Alloy Steels ST0111LA0007 U101K HT 7102 Heat Treat of Ultra High Strength Steel SMPP Req d ST0111LA0008 U131 HT 7102 Heat Treat of Precipitation Hardening CRES SMPP Req d ST0111LA0009 U111 HT 7102/2 Heat Treat of Aluminum Alloys SMPP Req d ST0111LA0011 U101L HT 7102 Surface Hardening of Carbon Alloy Steel ST0115AA0089 P420 NDT 7114/4,7114/4S Radiographic Inspection ST0115AA0102 P400 NDT 7114/2,7114/2S Magnetic Particle Inspection ST0115AA0114 P410 NDT 7114/1,7114/1S Penetrant Inspection General Requirements for Page 13 of 14 9/19/2017