STEELWORX SWL LEVERS CATALOGUE 2014/15

Transcription

1 STEELWORX SWL LEVERS CATALOGUE 2014/15

2 Introduction Eurospec was formed in 1997 as a subsidiary of Carlisle Brass specialising in the commercial sector of the architectural ironmongery market. Steelworx was launched in 2005 to provide beautifully engineered stainless steel commercial door hardware for the specification market. The SWL range will provide a cost effective stainless steel solution that can be used both commercially or for residential projects. Following the merger of Carlisle Brass Ltd and Eurospec in 2011 the brand has gone from strength to strength. Products include: High specification hinges Door control mechanisms Panic hardware Cylinder locks Mortice locks and latches Carlisle Brass Ltd. is an ISO 9001 and ISO certified company, which means that Eurospec branded products are fully traceable from point of manufacture to customer and that the environmental impact is being constantly measured and improved. Accredited products carrying the Eurospec brand are stringently tested to ensure they comply to the latest regulations, which makes Eurospec branded products the ideal choice for the professional installer, architect or specifier.

3 Contents Astoria 6 Cutlass 21 Valiant 7 Scimitar 22 Lucerna 8 Cervino 23 Berna 9 Shore 24 Breeze 10 Parigi 25 Brema 11 Nera 26 Peninsula 12 Spira 27 Tirolo 13 Treviri 28 Berlino 14 Philadelphia 29 Zurigo 15 Dresda 30 Carlton 16 SWT1016/i 32 Luenza 17 SWT1025i 33 Plaza 18 SWL102/ Lubecca 19 Accessories 35 Londra 20 1

4 Key to Finishes BSS = Bright Stainless Steel = Satin Stainless Steel BSS/ = Dual Finish Stainless Steel Care of Finishes Stainless steel needs to be cleaned for aesthetic considerations and to preserve corrosion resistance. Stainless steel is protected by a thin layer of chromium oxide. Oxygen from the atmosphere combines with chromium in stainless steel to form a passive chromium oxide film that protects from further corrosion. Any contamination of the surface by dirt or other material hinders this passivation process and traps corrosive agents, reducing corrosion protection. Thus some form of routine cleaning is necessary to preserve the appearance and integrity of the surface. They actually thrive with frequent cleaning and, unlike some other materials, it is impossible to wear out stainless steel by excessive cleaning. Stainless steel performs best when clean - cleanliness is essential for maximum resistance to corrosion. Stainless steel products should be wiped over with a clean cloth and warm water with a mild detergent on a frequent basis. For more stubborn dirt or stains use mild, non-scratching abrasing powders such as typical household cleaners. These can be used with warm water, bristle brushes, sponges or clean cloths. For more aggressive cleaning a small amount of vinegar can be added to the powder. Carbon steel brushes should be avoided as they may leave particles embedded in the surface, which can lead to rusting. Cleaning should always be immediately followed by rinsing in clean hot water and the surface then wiped completely with a dry towel. The maximum recommendation for routine cleaning is once a month and more often in areas subject to heavy soiling or frequent use. 2

5 Key to Symbols FD 30/60 The UK Construction Products Regulations require that door hardware for use on fire doors be safe and durable. BS EN 1906 BS EN 1906 is the British/European standard requirements and testing methods covering lever handles and knob furniture. BS 8300 is the design of buildings and their approaches to meet the needs of disabled people. 10 Year Mechanical Guarantee. Grade 304 Stainless Steel. GRADE 304 Suitable for use in domestic environments. Suitable for use in commercial environments. Suitable for use in industrial environments. INDUSTRIAL 3

6 Guide to BS EN 1906:2012 Digit 5 - Safety Grade 0: Normal use Grade 1: Safety application - to qualify for this grade, handles must have high strength handle-to-plate and plate-to-door fixing and/or handle to spindle fixing, such that they would withstand a person grabbing in order to prevent falling. It is recommended that only Safety Grade 1 furniture is used at the top of cellar steps or other staircases. Digit 1 - Category of Use Grade 1: Medium frequency of use with a high incentive to exercise care and a small chance of misuse, e.g. internal residential doors; Grade 2: Medium frequency of use by people with some incentive to exercise care but where there is some chance of misuse e.g. internal office doors; Grade 3: High frequency of use by public or others with little incentive to exercise care and with a high chance of misuse, e.g. public office doors Grade 4: High frequency of use on doors which are subject to frequent violent use, e.g. football stadiums, oil rigs, barracks, public toilets, etc Digit 6 - Corrosion Resistance Grade 0: No defined corrosion resistance Grade 1: Mild resistance - minimum requirement for internal use Grade 2: Moderate resistance Grade 3: High resistance - minimum requirement for external use Grade 4: Very high resistance - recommended for use in exposed marine atmospheres or very polluted industrial environments. Note: Products intended to develop a natural patina (such as bronze or brass) are not required to comply with any requirements A Digit 2 - Durability Grade 6: Medium use - 100,000 cycles Grade 7: High use - 200,000 cycles The tests undertaken to achieve these grades involve the application of additional forces to the door furniture in order to stimulate the conditions of use likely to be experienced in the field. Digit 3 - Test Door Mass No requirement Digit 7 - Security Grade 0: Not approved for use on burglary resistant doors Grade 1: Mild burglary resistance Grade 2: Moderate burglary resistance Grade 3: High burglary resistance Grade 4: Extra high burglary resistance Note: The main requirements include resistance to drilling, close fitting plates or escutcheons to help protect the lock and support the cylinder. They must be resistant to removal from the outside of the door and make provision to minimise the cylinder projection to a maximum of 3mm. Full details of the requirements can be found in BS EN Digit 4 - Fire Resistance Grade 0: Not approved for use on fire/smoke door assemblies. Grade 1: Suitable for use on fire/smoke door assemblies. Note: A Grade 1 classification means only that the furniture has been designed for use on fire/smoke control doors; the actual fire performance achieved (e.g. fire integrity of 30 minutes on a partially glazed timber door etc.) will be contained in a separate fire test report. Digit 8 - Type of operation Type A: Spring assisted furniture Type B: Spring loaded furniture Type U: Unsprung furniture 4

7 5

8 Astoria SWL1006DUO Astoria Lever handle length 135mm, Ø 19mm Lever projection 62mm Rose Ø mm x 7mm Solid G304 stainless steel Dual finish stainless steel BSS/ 6

9 Valiant SWL1008DUO Valiant Lever handle length 134mm, Ø 19mm Lever projection 53mm Rose Ø mm x 7mm Solid G304 stainless steel BSS/ Dual finish stainless steel 7

10 Lucerna SWL1009DUO Lucerna Lever handle length 133mm, Ø 19mm Lever projection 60mm Rose Ø mm x 7mm Solid G304 stainless steel Dual finish stainless steel BSS/ 8

11 Berna SWL1010DUO Berna Lever handle length 136mm, Ø 19mm Lever projection 62mm Rose Ø mm x 7mm Solid G304 stainless steel BSS/ Dual finish stainless steel 9

12 Breeze SWL1121 Breeze Lever handle length 124mm Lever projection 68mm Rose Ø mm x 7mm Formed G304 stainless steel

13 Brema SWL1122 Brema Lever handle length 135mm, Ø 19mm Lever projection 64mm Rose Ø mm x 7mm Solid G304 stainless steel 11

14 Peninsula SWL1127 Peninsula Lever handle length 126mm, Ø 20mm Lever projection 62mm Rose Ø mm x 7mm Formed G304 stainless steel

15 Tirolo SWL1131 Tirolo Lever handle length 120mm Lever projection 58mm Rose Ø mm x 7mm Solid G304 stainless steel 13

16 Berlino SWL1132 Berlino Lever handle length 125mm, Ø 22mm Lever projection 60mm Rose Ø mm x 7mm Solid G304 stainless steel BS8300 suitable

17 Zurigo SWL1133 Zurigo Industrial Lever handle length 125mm, Ø 23mm Lever projection 57mm Rose Ø mm x 7mm Solid G304 stainless steel BS8300 suitable INDUSTRIAL 15

18 Carlton SWL1134 Carlton Lever handle length 127mm Lever projection 60mm Rose Ø mm x 7mm Formed G304 stainless steel

19 Luenza SWL1135 Luenza Lever handle length 133mm, Ø 19mm Lever projection 64mm Rose Ø mm x 7mm Formed G304 stainless steel BS8300 suitable 17

20 Plaza SWL1160 Plaza Lever handle length 132mm Lever projection 71mm Rose Ø mm x 7mm Formed G304 stainless steel

21 Lubecca SWL1161 Lubecca Lever handle length 128mm Lever projection 66mm Rose Ø mm x 7mm Solid G304 stainless steel 19

22 Londra SWL1162 Londra Lever handle length 134mm Lever projection 58mm Rose Ø mm x 7mm Formed G304 stainless steel

23 Cutlass SWL1164 Cutlass Lever handle length 132mm, Ø 19mm Lever projection 54mm Rose Ø mm x 7mm Formed G304 stainless steel BS8300 suitable BSS Bright stainless steel 21

24 Scimitar SWL1165 Scimitar Lever handle length 134mm, Ø 22mm Lever projection 67mm Rose Ø mm x 7mm Formed G304 stainless steel BS8300 suitable Bright stainless steel BSS 22

25 Cervino SWL1166 Cervino Lever handle length 126mm, Ø 19mm Lever projection 68mm Rose Ø mm x 7mm Formed G304 stainless steel BSS Bright stainless steel 23

26 Shore SWL1167DUO Shore Lever handle length 140mm, Ø 19mm Lever projection 65mm Rose Ø mm x 7mm Formed G304 stainless steel Dual finish stainless steel BSS/ 24

27 Parigi SWL1168 Parigi Lever handle length 127mm Lever projection 62mm Rose Ø mm x 7mm Formed G304 stainless steel 25

28 Nera SWL1190 Nera Industrial Lever handle length 141mm, Ø 19mm Lever projection 65mm Rose Ø mm x 7mm Tubular G304 stainless steel BS8300 suitable Bright stainless steel INDUSTRIAL BSS 26

29 Spira SWL1191 Spira Industrial Lever handle length 133mm, Ø 19mm Lever projection 65mm Rose Ø mm x 7mm Tubular G304 stainless steel INDUSTRIAL BSS Bright stainless steel 27

30 Treviri SWL1192 Treviri Lever handle length 128mm, Ø 19mm Lever projection 65mm Rose Ø mm x 7mm Tubular G304 stainless steel Dual finish stainless steel BSS/ 28

31 Philadelphia SWL1194 Philadelphia Lever handle length 137mm, Ø 19mm Lever projection 66mm Rose Ø mm x 7mm Tubular G304 stainless steel BSS/ Dual finish stainless steel 29

32 Dresda SWL1196 Dresda Lever handle length 128mm, Ø 19mm Lever projection 65mm Rose Ø mm x 7mm Tubular G304 stainless steel

33 31

34 STEELWORX SWL Thumbturns SWT1016 SWT1016i SWT1016 SWT1016i 7 SWT1016 Rose Ø mm x 7mm Concealed Rose G304 stainless steel Polished stainless steel Dual finish stainless steel SWT1016i 7 BSS/ BSS GRADE 304 FD 30/60 32

35 STEELWORX SWL Disabled Thumbturn SWT1025i 7 Lever handle length 60mm, Ø 10mm Lever projection 37mm Rose Ø mm x 7mm Concealed Rose G304 stainless steel BSS/ Bright stainless steel Dual finish stainless steel BSS GRADE 304 FD 30/60 33

36 Escutcheons SWL102 SWL103 SWL102 Euro SWL103 Lock 7 SWL102 Rose Ø mm x 7mm Concealed Rose G304 stainless steel 7 Bright stainless steel Dual finish stainless steel SWL103 BSS/ BSS For matching rose pack for use with Steelworx pull handles, please specify SWL1134 GRADE 304 FD 30/60 34

37 Roses Accessories SWR1134BSS SWR1134 Steelworx SWL Rose Pack SWR1136BSS SWR1136 Steelworx SWL Spare Outer Rose Spindles ATS mm conversion sleeve SP6T Taylor spindle ASS5100 8mm split follower ALP5038 1/2 set spindle adaptor ALS1002H 120mm heso longer spindle Fixings & Screws FIXSSL Spare fitting screw pack AGWS1000H Heso spare grub screw 35

38 36

39 CSL Residential A range of levers on backplate in 201 grade stainless steel orientated to the housing sector. CSL Contract Stainless A range of commercial tubular 304 grade stainless steel levers on rose, backplate and pull handles. SSL A range of 304 grade designer levers and pull handles with a square motif. SW A classic range of 316 grade stainless steel, commercially orientated pull handles and accessories with finely engineered details.

40 Carlisle Brass Ltd. Parkhouse Road, Carlisle, Cumbria, CA3 0JU Sales: Web: