3M Three-Wall Header Latch/Ejector, Straight and Right Angle 3000 Series

Transcription

1 M Three-Wall Header Latch/Ejector, Straight and Right ngle 000 Series Military (with M's 518 or N518 polarizing key) and center bump polarization Low profile Optional ejector latches Mounting holes for securing header to board Three wall shroud provides design flexibility Solder tail and wrap tail options Optional polarizing posts available Optional high temperature insulator suitable for "no lead" soldering operations High temperature option is suitable for reflow soldering using "paste in hole" techniques See Regulatory Information ppendix for chemical compliance information Date Modified: February 2, 2007 Sheet 1 of 5 Physical Insulator Material: Glass Filled Polyester (PT) Glass Filled Polyester (PCT) - High Temp Option Flammability: UL 94V-0 Color: Gray (PT), eige (PCT), or lack (PCT) Contact Material: Copper lloy Plating Underplating: 100 µ [ 2.54 µm ] Nickel - Overall Wiping rea: 0 µ [ 0.76 µm ] Gold Solder Tails: 200 µ [ 5.08 µm ] Tin Lead or Matte Tin (See Ordering Information) Marking: M Logo, Part Identification Number and Orientation Triangle Electrical Current Rating: Insulation Resistance: Withstanding Voltage: 1 > Ω at 500 V DC 1000 V RMS at Sea Level Environmental Temperature Rating: -55 C to +105 C Process Rating: 260 C (High Temp. PCT insulator) single pass (per J-STD-020C) PT gray insulator, maximum insulator temperature 191 C (solder wave process only) Moisture Sensitivity Level: 1 (per J-STD-020C) High Temp. (PCT) versions only UL File No.: E M is a trademark of M Company

2 M Three-Wall Header Latch/Ejector, Straight and Right ngle 000 Series -X0XX Header without Latchs.08 [2.0] -X2XX Header with Short Ejector/Latch for M Sockets without Strain Relief.424 ±.010 [ ].97 Ref [24.6].08 [2.0] -XXX Header with Long Ejector/Latch for M Sockets with Strain Relief.57 ±.010 [ ] 1.07 Ref [27.2].7 Ref [9.4].46 Ref [11.7].025 ±.002 Sq Typ [ 0.64 ].0 [7.6].24 [6.1] REF. D E ±.010 F Typ.1. 2X O.100 SEE NOTE # POSITION #1 REF Section - (Straight) Position 1 Orientation Triangle Notch (See Table 1 & Note1) Notch (See Table 1).025 ±.002 Sq Typ [ 0.64 ].21 [5.].16 [4.1] Notch C (See Table 1 & Note 1) F Typ.100 Ref.24 [6.1].0 [7.6].68 [17.].5 [8.9].12 [.0].049 Ref Section - (Right ngle) E ± [0.51] 2X Ø.100 (See Note 2) C.197 [5.00].20 [5.1] Sheet 2 of 5 M is a trademark of M Company

3 M Three-Wall Header Latch/Ejector, Straight and Right ngle 000 Series Pin Quantity Table 1 M Part Number Dimensions Polarization Notches Provided C D [2.1] [28.07].865 [21.97].71 [18.0] C [7.2] 1.05 [.15] [27.05].91 [2.1] C [9.7] [5.69] [29.59] 1.01 [25.6] C [44.8] [40.77] 1.65 [4.67] 1.21 [0.7] C [52.4] [48.9] [42.29] 1.51 [8.] C [62.6] 2.05 [58.55] [52.45] 1.91 [48.5] C [70.2] [66.17] 2.65 [60.07] 2.21 [56.1] C [82.9].105 [78.87] [72.77] 2.71 [68.8] C [95.6].605 [91.57].65 [85.47].21 [81.5] C [100.7].805 [96.65].565 [90.55].41 [86.6] C M Part Number Suffix -1XX2-2XX2-1X0-2X0 Table 2 Contact Tail Dimension E Pin Cross Section Dimension G Solder Tail for.062 [1.57] Thick PC oard Solder Tail for.094 [2.9] to.125 [.18] Thick PC oard.112 [2.84].155 [.94] Dimension F Diagonals Corner Radii ±.0005 [0.622] ±.0005 [0.622] ±.001 [0.71] ±.001 [0.71] Ref [0.191] Ref [0.191] ø.05 ±.00 [0.89] (See Note ) ø.05 ±.00 [0.89].00 [7.62] Side to Side Stackability or Ø.116 [2.95] Ø.106 [2.69] (See Note 2) G Dim Ø.106 [2.69].41 [10.4] Max to Edge of PC for Daisy Chain (See Note 2) or Ø.116 [2.95] G Dim.060 [1.52].100 ±.00 Position ± [8.94] Recommended Mounting Hole Pattern (Straight).029 [0.74].100 ±.00 Notes: 1. Notches & C will accomodate M Polarizing Keys (M Part #518 or N518). 2. ccepts Rear and Front mounting hardware: Rear Entry: #4-24 thread cutting screw, M Part #41-5,.116 [2.95] dia mounting hole Front Entry: (Prior to installation of latch on Straight Versions) #2-56 bolt and nut, M Part #41-6,.106 [2.69] dia mounting hole. The recommended PC hole size for the kinked tail positions on the.112 solder tail connector is.05 ±.002. Kink is located.05 below bottom surface of plastic. External radius of kink toward part centerline. Position ± [5.89] Recommended Mounting Hole Pattern (Right ngle) C Inch [mm] Tolerance Unless Noted Inch ±.1 ±.01 ±.005 [ ] Dimensions for Reference only Sheet of 5 M is a trademark of M Company

4 M Three-Wall Header Latch/Ejector, Straight and Right ngle 000 Series Ordering Information lank = Std. Temp Gray (PT) /(lank or U Pltg. Req'd.) N = High Temp eige (PCT) /(lank or U Pltg. Req'd.) N = High Temp lack (PCT)/(R Plating Req'd) XXXX-XXXX XX M Part Number (See Table 1) Latch/Ejector System 0 = No Latch/Ejector 2 = Short Roll PinLatch/Ejectors = Long Roll Pin Latch/Ejectors blank or U = 0 µ" Gold with Sn/Pb Tails (pp. E & C2 pply) R = 0 µ" Gold with Matte Tin Tails (pp. E1 & C1 pply) Shroud and Pin Configuration 1 = Wall, Right ngle Solder Tail 2 = Wall, Straight Solder Tail Tail 02 = Solder Tail for.062 [1.57] Thick oard K2= Kinked Solder Tails for.062 [1.57] Thick oard 0 = Solder Tails for.094 to.125 [2.9 to.18] Thick oard Part Customization This spec sheet details our standard offering. M has several capabilities that can provide a part tailored to your specific needs. sk your M sales representative or customer service for more details. Use of snap-in style latch/ejectors in either short (NXXX- X5XX) or long (NXXX-X6XX) styles, installed or shipped separately (the -5 & -6 snap-in latches are dimensional and functional equivalents to the -2 & - roll pin latches) which are also available separately with roll pins included. Refer to chart below. If ordering snap-in or roll pin style latches separately, please use the below chart Short Latch Long Latch Latch Style Color Standard Temperature (PT) Roll Pin Gray High Temperature (PCT) N505-2 N505- Roll Pin eige High Temperature (PCT) N505-2 N505- Roll Pin lack High Temperature (PP) Snap-In Gray High Temperature (PP) N505-0 N505-1 Snap-In eige High Temperature (PP) N505-0 N505-1 Snap-In lack Kinked Tail (K2 option) positions: 2500 & 000 Series Shrouded Header Total Number of Pins Number of Tails Kinked Positions Kinked Selective pin removal (T or other compatibility) Wire wrap tail styles Kinked Tail Detail: Kink is located.05 below bottom surface of plastic. External radius of kink toward part centerline. Sheet 4 of 5 M is a trademark of M Company

5 M Three-Wall Header Latch/Ejector, Straight and Right ngle 000 Series Polarizing Post.21 [8.15] 201- PT Gray LCP lack.100 Dia Note: Insert Post into one mounting hardware hole on bottom of header. Set post to protrude.115 [2.92]. Polarizing Keys Dim N518 LCP lack PT Gray.02 reakaway Tab.15 [.8].4 Ref [8.6].09 [2.] Note: #2216 / Scotchweld can be used to adhere keys (Installed from bottom of board) Mounting Hardware 41-6 (Must be inserted prior to latch on vertical headers).1 [7.9].50 [12.7] Panhead Thread Cutting Screw: #4-24 X 5/16 Type: US Std T, Federal G 41-5 & 6 Material - Stainless Steel Hex Head olt, Nut and Washer olt - #2-56 X 1/2 Sheet 5 of 5 M is a trademark of M Company

6 Regulatory Information ppendix (RI) M Electronic Solutions Division/Interconnect EUROPE ppendix E1: European Union RoHS Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment, as amended by EU Commission Decision 2005/618/EC. This product is RoHS Compliant 2005/95/EC. RoHS Compliant 2005/95/EC means that the product or part ( Product ) does not contain any of the substances in excess of the maximum concentration values in EU Directive 2002/95/EC, as amended by Commission Decision 2005/618/ EC, unless the substance is in an application that is exempt under EU RoHS. Unless otherwise stated by M in writing, this information represents M s best knowledge and belief based upon information provided by third party suppliers to M. In the event any product is proven not to conform with M s Regulatory Information ppendix, then M s entire liability ppendix E2: European Union RoHS Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment, as amended by EU Commission Decision 2005/618/EC. This product contains lead in the compliant pin area in excess of the maximum concentration value allowed but is compliant by exemption under EU Commission Decision 2005/747/EC. RoHS Compliant 2005/95/EC means that the product or part ( Product ) does not contain any of the substances in excess of the maximum concentration values in EU Directive 2002/95/EC, as amended by Commission Decision 2005/618/ EC, unless the substance is in an application that is exempt under EU RoHS. Unless otherwise stated by M in writing, this information represents M s best knowledge and belief based upon information provided by third party suppliers to M. In the event any product is proven not to conform with M s Regulatory Information ppendix, then M s entire liability ppendix E: European Union RoHS Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment as amended by Commission Decision 2005/618/EC. This product contains lead in the solder tail area in excess of the maximum concentration value allowed. Unless otherwise stated by M in writing, this information represents M s best knowledge and belief based upon information provided by third party suppliers to M. In the event any product is proven not to conform with M s Regulatory Information ppendix, then M s entire liability CHIN ppendix C1: China RoHS Electronic Industry Standard of the People s Republic of China, SJ/T , Requirements for Concentration Limits for Certain Hazardous Substances in Electronic Information Products. This symbol, per Marking for the Control of Pollution Caused by Electronic Information Products, SJ/T , means that the product or part does not contain any of the following substances in excess of the following maximum concentration values in any homogeneous material: (a) 0.1% (by weight) for lead, mercury, hexavalent chromium, polybrominated biphenyls or polybrominated diphenyl ethers; or (b) 0.01% (by weight) for cadmium. Unless otherwise stated by M in writing, this information represents M s best knowledge and belief based upon information provided by third party suppliers to M. In the event any product is proven not to conform with M s Regulatory Information ppendix, then M s entire liability RI-2217-

7 20 ppendix C2: China RoHS Electronic Industry Standard of the People s Republic of China, SJ/T , Requirements for Concentration Limits for Certain Hazardous Substances in Electronic Information Products. This symbol, per Marking for the Control of Pollution Caused by Electronic Information Products, SJ/T , means that the product or part does contain a substance, as detailed in the chart below, in excess of the following maximum concentration values in any homogeneous material: (a) 0.1% (by weight) for lead, mercury, hexavalent chromium, polybrominated biphenyls or polybrominated diphenyl ethers; or (b) 0.01% (by weight) for cadmium. Unless otherwise stated by M in writing, this information represents M s best knowledge and belief based upon information provided by third party suppliers to M. The numerical reference in the symbol above should not be construed as a representation regarding the product s life or an extension of a product warranty. The product warranty is stated below. In the event any product is proven not to conform with M s Regulatory Information ppendix, then M s entire liability and uyer s exclusive remedy will be in accordance with the product Warranty stated below. Name and Content of Hazardous Substances or Elements Important Notice ll statements, technical information, and recommendations related to M s products are based on information believed to be reliable, but the accuracy or completeness is not guaranteed. efore using this product, you must evaluate it and determine if it is suitable for your intended application. You assume all risks and liability associated with such use. ny statements related to the product which are not contained in M s current publications, or any contrary statements contained on your purchase order shall have no force or effect unless expressly agreed upon, in writing, by an authorized officer of M. Warranty; Limited Remedy; Limited Liability. This product will be free from defects in material and manufacture for a period of ninety (90) days from the time of purchase. M MKES NO OTHER WRRNTIES INCLUDING, UT NOT LIMITED TO, NY IMPLIED WRRNTY OF MERCHNTILITY OR FITNESS FOR PRTICULR PURPOSE. If this product is defective within the warranty period stated above, your exclusive remedy shall be, at M s option, to replace or repair the M product or refund the purchase price of the M product. Except where prohibited by law, M will not be liable for any indirect, special, incidental or consequential loss or damage arising from this M product, regardless of the legal theory asserted. M Electronic Solutions Division 6801 River Place lvd. ustin, TX / Printed in US M 2007