AIR BLEED VALVES : ST1004 PIPE FLANGE KITS : "F3","F5","F6" SERIES

Transcription

1 AIR BD VAVS : ST04 PIP ANG ITS : "3","5","6" SRIS General Information Pub. C-0 Air Bleed Valves...Page These air bleed valves are designed to use, at the start-up of the pumps, to bleed off the air enclosed in the suction line or the other lines in the system. Graphic Symbol Pipe lange its "3" Series...Page 3 Socket Welding "5" Series...Page 6 Threaded The dimensions of the flange mounting surface are based upon SA 4 Bolt Split lange ( Series). Threaded Socket Welding "6" Series...Page The dimensions of the flange mounting surface are based upon SA 4 Bolt Split lange (High Series). Threaded Socket Welding No.

2 Air Bleed Valves 3/8 Threaded s : ST04 Specifications / Model Number ation / Others Up to 5 MPa (36 PSI) Graphic Symbol Specifications Model Numbers ST04-5- ST04-- Max. Operating MPa (PSI) Reseating MPa (PSI) Cracking MPa (PSI) 5 (36) 0.5 () 0. (49) low Rate to Reseating /min (U.S.GPM) 5 (.3) (.64) Range of Usage to Pump Output low or 0 to 75 /min (5.8 to 9.8 U.S.GPM) or Over 75 /min (9.8 U.S.GPM) 0. (.44) Model Number ation ST Series Number ST04: Air Bleed Valve low Rate to Reseating 5: 5 /min (.3 U.S.GPM) : /min (.64 U.S.GPM) Number s Japanese "JIS" 80: uropean 90: N. American Instructions When the valve is used to bleed off the air from the pump, connect the inlet port of the valve to the discharge port of the pump as close as possible. When removing the air from the pipes, install the valve at the highest position of the systyem. In eighter case, the outlet port of the valve must be connected to the tank, the end of which is located below the oil level in the resevoir. Hydraulic luids Type of Hydraulic luids Petroleum Base Oils... Use R & O (Rust and Oxidation inhibitor) type oils or anti-wear type oils (equivalent to ISO VG-3 or 46) Synthetic luids...use phosphate ester type fluid or polyol ester type fluids. Water Containing luids..use water glycol type fluids or water in oil emulsion type fluids. Other Special luids...consult factory for information. Recommended viscosity and Oil Temperatures Viscosity ranging between 5 and 400 mm /S (77 and 800 SSU). Oil temperatures between -5 and +70 C (5 and 60 ) Use hydraulic fluids which satisfy the recommended viscosity and oil temperatures given above. iltration Recommended...5 microns or less. ST04- -/80/90 C Outlet Port "A" Thd. B Model Numbers ST04- - ST ST "A" Thd. Rc 3/8 3/8 BSP. 3/8 NPT mm (Inches) B 70 4 C (.94) 8 (3.3) 7 (.06) 70 4 (.94) ST04- - Inlet Port "A" Thd. DIMNSIONS IN MIIMTRS (INCHS) No.

3 "3" Series Pipe lange its Socket Welding : 3- -A Threaded : 3- -B Block Type : 3- -C Up to 5 MPa (36 PSI) Specifications Max. Operating...5 MPa (36 PSI) Socket Welding Threaded Model Number ation - Material of Seal 3 Series Number -03W lange -A Type of Pipe -N & Bolts - Number s NBR (Buna N) Seal : PM (Viton) Seal (or Synthetic fluids) 3 03W, 03, 06V 06W, 06, W, 6W, 6 4W, 4 03W, 03, 06W 06, W, 6W, 6, 4W 4 03W, 03, 06V 06W, 06, W, 6W, 6 4W, 4 03W, 03, 06W 06, W, 6W, 6, 4W 4 A: Pipe Socket Welding C: Block Type B: Threaded With and Mounting Bolts N: No and Mounting Bolts With and Mounting Bolts N: No and Mounting Bolts Japanese "JIS" & uropean 90: N. American Japanese "JIS" 80: uropean 90: N. American Three different design standards are available as shown blow. Select the suitable design standard to your requirement. Type of Pipe Pipe Thread Mounting Bolt ( ) Pipe Socket Welding Block Type Threaded Japanese "JIS" & uropean N. American Japanese "JIS" uropean N. American Rc BSP. NPT Unified Thd. Unified Thd. No.3

4 "3" Series Pipe lange its Pipe Socket Welding / Block Type Pipe Socket Welding 3- -A -/90 Block Type 3- -C -/90 "H" Dia. Through "D" Sq. Mounting Surface Surface should have a good machined finish. "J" Dia. "" Dia. "N" Dia. Max. Soc. Hd. P P it Numbers 3-03W W V W W W- - 3-W W W W W /4 3/8 3/8 / 3/4 -/4 -/ -/ 3 Dimensions mm (Inches) D H J N P 54 (.3) 58 (.8) 76 (.99) 0 (3.94) 40 (5.5) 36 (.4) (.0) 73 (.87) 3 (4.06) 7 (.06) (.38) 44 (.73) (.043) 3.5 (.53) 7.5 (.69) 4 (.94) 4.3 (.56) 7.8 (.70) 7.8 (.70). (.87) 7.7 (.09).5 (.36) 43. (.70) 49. (.93) 6. (.4) 77. (3.04) 90.0 (3.54).5 (.49).5 (.49) 6 0 (.79) 5 (.98) 3.5 (.4) 37.5 (.48) 47.5 (.87) 60 (.36) 7 (.80) 8 (.3) 9 (.) 9 (.) (.47) (.7) 0 (.79) (.87) 5 (.98) 5 0 (.79) 3.5 (.4) 50 (.97) 75 (.95) (.7) 7.5 (.69) 8 (.7) 7.5 (.69) 5 (.98). (.87) 5 (.98). (.87) 36 (.4) 38.6 (.5) 36 (.4) 38.6 (.5) SO-NB-G5 SO-NB-G SO-NB-G60 SO-NB-G85 M g. 3/8-6UNC -/ g. M g. 3/8-6UNC -/ g. M g. M g. 3/8-6UNC -/ g. M g. 3/8-6UNC -/ g. M 45 g. /-3UNC -3/4 g. M 45 g. /-3UNC -3/4 g. M6 60 g. 8/5-UNC -/4 g. M6 60 g. 8/5-UNC 3-/4 g. M 80 g. 7/8-9UNC 3-/4 g. M 80 g. 7/8-9UNC 3-/4 g. 0.5 (.) 0.8 (.8).4 (3.).7 (6.0) 5.8 (.8) mass is the value including socket head cap screws. No.4

5 "3" Series Pipe lange its Threaded Threaded Japanese "JIS" & N. American Standarad uropean Standarad "H" Dia. Through 3- -B -/90 "D" Sq. "H" Dia. Through "D" Sq. 3- -B mm ( IN.) Mounting Surface Surface should have a good machined finish. "J" Dia. "" Dia. "J" Dia. "J" Dia. "N" Dia. Max. P P : 03W to P : 6W to 4 it Numbers Dimensions mm (Inches) D H J N P 3-03W-B W-B W-B B B -80 Rc /4 /4 BSP. /4 NPT Rc 3/8 3/8 BSP. 54 (.3) 36 (.4).5 (.45) 4 5 (.47) (.96) SO-NB-G5 M g. 3/8-6UNC -/ g. M g. 0.5 (.) 3-03-B -90 3/8 NPT /8-6UNC -/ g. 3-06V-B W-B W-B W-B B B B -90 Rc3/8 Rc / / BSP. / NPT Rc 3/4 3/4 BSP. 3/4 NPT 58 (.8) 40 7 (.06) (69) 9 (.75) 7.5 (.69) 3 (.9) 4.5 (.96) 3 (.9) 7 0 (.79) 9 (.4).5 (.40) 0 (.79) (.5) 7.5 (.69) SO-NB-G M g. M g. 3/8-6UNC -/ g. M 40 g. 3/8-6UNC -3/4 g. 0.8 (.8) 3-W-B - 3-W-B W-B B - 3--B B W-B - 3-6W-B W-B B B B W-B - 3-4W-B W-B B B B -90 Rc BSP. NPT Rc -/4 -/4 BSP. -/4 NPT Rc -/ -/ BSP. -/ NPT Rc BSP. NPT Rc -/ -/ BSP. -/ NPT Rc 3 3 BSP. 3 NPT 76 (.99) 0 (3.94) 40 (5.5) 56 (.0) 73 (.87) 3 (4.06) 7 (.06) (.38) (.8) 39 (.54) 44 (.73) 49 (.93) 3.5 (.53) 7.5 (.69) 4 (.94) 9 (.4).5 (.0) 9 (.4) 3.5 (.4) 43.5 (.7) 45 (.77) 43.5 (.7) 47.5 (.87) (.85) 70 7 (.80) (.87) (.87) (.87) 0 (.79) 0 (.79) 43.5 (.7) 53 (.09) 3.5 (.4) 50 (.97) 75 (.95) 8 (.7) 7.5 (.69) (.6) 5 (.98) 8.5 (.) 4.5 (.96) 36 (.4) 38.6 (.5) 3 (.) 33.6 (.3) SO-NB-G60 SO-NB-G85 M 45 g. /-3UNC -3/4 g. M 50 g. /-3UNC g. M6 60 g. 5/8-UNC -/ g. M6 60 g. 5/8-UNC -/ g. M 80 g. 7/8-9UNC 3-/4 g. M 80 g. 7/8-9UNC 3-/4 g..4 (3.).7 (6.0) 5.8 (.8) is the value including socket head cap screws. No.5

6 "5" Series Pipe lange its Threaded : 5- -A Socket Welding : 5- -B Butt Welding : 5- -C Up to 8 MPa (4060 PSI) Mounting Surface : SA J58 (Port Dimensions or Bolted lange, Series) Specifications Max. Operating : Maximum operating pressure varies with the type of pipe connection or flange size. Refer to the applicable installation drawings. Threaded Socket Welding Model Number ation A - Material of Seal Series Number lange Type of Pipe Number s 04W, 04, 06X 06, 08, 08W,, 6, 6W, 0 4, 8, 3 Japanese "JIS" NBR (Buna N) Seal 04, 06, 08,, 6 0 A: Threaded 80: uropean 04W, 04, 06 08,, 6, 6W, 0 90: N. American : PM (Viton) Seal (or Synthetic luids) 5 04W, 04, 06X 06, 08, 08W,, 6, 6W, 0 4, 8, 3 04W, 04, 06 08,, 6, 6W, 0,4 8, 3 B: Socket Welding Japanese "JIS" & uropean 90: N. American 04, 06, 08,, 6 0 C: Butt Welding Japanese "JIS" & uropean 90: N. American Three different design standards are available as shown below. Select the suitable design standard to your requirement. Type of Pipe Threaded Japanese "JIS" uropean N. American Pipe Thread Rc BSP. NPT Mounting Bolt ( ) Unified Thd. Pipe Socket Welding Butt Welding Japanese "JIS" & uropean N. American Unified Thd. No.6

7 "5" Series Pipe lange its Threaded Japanese "JIS" & N.American Japanese "JIS" : 5- -A- N. American : 5- -A-90 "J" Dia. Through D Mounting Surface Surface should have a good machined finished. H "N" Dia. Max. Soc. Hd it Numbers Dimensions mm (Inches) D H J N Max. Operating MPa (PSI) Recommended Tightening Torque (Tolerance ±%) Nm (IN.lbs.) 5-04W-A A- 5-04W-A A X-A A A A- 5-3-A- Rc 3/8 Rc / 3/8 NPT / NPT Rc 3/4 3/4 NPT Rc 3-/ Rc (.89) 6 (4.57) (5.8) 50 (5.9) 54 (.3) 65 (.56) 7.5 (.689). (.874) (.500) (.6) (.8) (.39) (.5) M8 45 g. M 45 g. 3/8-6UNC -3/4 g. 5-08W-A- Rc 3/ A- Rc (.7) (.03) (.063) (.433) (.8) (.0) M 45 g A-90 NPT 4.5 3/8-6UNC -3/4 g. 5--A- Rc -/ (.433) 38 3 M 55 g. 5--A-90 -/4 NPT (.5) (3.5) (.89) (.3) (.50) 9. (.6) (.47) 7/6-4UNC -/4 g. 5--A- Rc -/ M 55 g. 5--A-90 -/ NPT (3.70) (.406) (.75) (.53) (.50) 9. (.50) /-3UNC -/4 g. 9. (.89) 5-6-A-90 NPT 5 (.0) 5-0-A- Rc -/ W-A- Rc -/ 48 7 (.89) 5-6-A- Rc (.0) 5-6W-A-90 -/ NPT (3.) (4.0) (.689) (3.063) (.53) (.50) 48 M 55 g. /-3UNC -/4 g. M 65 g. 5-0-A A- -/ NPT Rc 3 (4.0) (4.49) (.000) (3.500) (.53) (.89).8 (.48) (.86) (.437) (4.89) (.99) /-3UNC -3/4 g. M6 70 g (5.3) 53 (6.0) 6 (6.38) (.75) 77.8 (3.068) 8.8 (.6) (.874) (.8) (.433) (4.75). (5.6) 4.5 (.689) (.09) 9 (.75) (3.46) (3.98) M8 40 g. 5/6-8UNC -3/4 g. M6 70 g. M6 70 g. SO-NB-P SO-NB-G SO-NB-G SO-NB-G50 SO-NB-G60 SO-NB-G65 SO-NB-G60 SO-NB-G65 SO-NB-G75 SO-NB-G85 SO-NB-G0 SO-NB-G (50) (50) 7.5 (540) (50) 7.5 (540) 7.5 (540). mass is the value including socket head cap screws.. The values of recommended tightening torque are for socket head cap screws and apply to when these flanges are used for pressure line. 3.5 (5) 0.5 (.) 0.7 (.5) 0.9 (.0). (.6).5 (3.3).8 (4.0).7 (3.8).8 (4.0).7 (3.8).0 (4.4).7 (6.0) 3.4 (7.5) 3.7 (8.) (3) (3) 68.5 (606) 68.5 (606) 68.5 (606) 8 (44) 8 (44) 8 (44) 87 (540) No.7

8 "5" Series Pipe lange its Thread uropean uropean 5- -A-80 "H" Dia. Through "J" C' bore "N" Deep D mm (.0-.0 IN.) Q Q Mounting Surface Surface should have a good machine finish. G "S" Dia. Max. : / to -/ : & -/ it Dimensions mm (Inches) Numbers D G H J N Q S A-80 / BSP. M8 (.3) (.689) (.500) (.6) (.) (.50) (.) g. SO-NB-P A-80 3/4 BSP. M g. SO-NB-G (.89) (.874) (.874) (.433) (.69) (.) (.58) (.79) (.75) A-80 BSP. M g. SO-NB-G (.7) (3.03) (.03) (.063) (.433) (.69) (.) (.58) (.98) A-80 -/4 BSP. M 45 g. (.5) (3.7) (.89) (.3) (.433) (.69) (.54) (.66) (.87) (.6) A-80 -/ BSP. M 45 g. SO-NB-G50 (3.90) (.406) (.75) (.53) (.6) (.69) (.53) (.87) (.50) A-80 BSP. M 45 g. SO-NB-G65 (3.) (4.) (.689) (3.063) (.53) (.6) (.69) (.53) (.) (.97) A-80 -/ BSP. M 50 g. SO-NB-G75 (4.0) (4.65) (.000) (3.500) (.53) (.8) (.69) (.53) (.) (.48) mass is the value including socket head cap screws. Max. Operating MPa (PSI) (50) 7.5 (540) 7.5 (540) kg (lbs.) 0.5 (.) 0.7 (.5) 0.9 (.0). (.6).6 (3.5).8 (4.0).9 (4.) Recommended Tightening Torque or it Numbers 5-04-A A A A A A A-80 Tightening Torque Recommendation Nm (IN.lbs.) Tolerance (3) 68.5 (606) 8 (44) ±% Note: The values of tightening torque above apply to when these flanges are used for pressure line. No.8

9 Japanese "JIS" & uropean : 5- -B- N. American : 5- -B-90 "H" Dia. Through G D "N" Dia. "5" Series Pipe lange its Pipe Socket Welding Q "S" Dia. Max. Mounting Surface Surface should have a good machined finish. Recommended Tightning Torque or Tightening Torque it Numbers Recommendation Tolerance Nm (IN.lbs.) 5-04W-B 5-04-B (3) 5-06X-B 5-06-B 5-08W-B 68.5 (660) 5-08-B 5--B ±% 5--B 5-6W-B 8 (44) 5-6-B 5-0-B 5-4-B 5-8-B 87 (540) 5-3-B Note: The values of tightening torque above apply to when these flanges are used for pressure line. it Numbers 5-04W-B- 5-04W-B B B X-B B B W-B B B B- 5--B B- 5--B W-B- 5-6W-B B- 5-6-B B- 5-0-B B- 5-4-B B- 5-8-B B- 5-3-B-90 3/8 / 3/4 3/4 -/4 -/ -/ -/ 3 3-/ 4 Dimensions mm (Inches) D G H N (.89) 55 (.7) 64 (.5) 7 85 (3.) (4.0) 6 (4.57) (5.8) 50 (5.9) 54 (.3) 65 (.56) (3.5) 94 (3.70) (4.0) 4 (4.49) (5.3) 53 (6.0) 6 (6.38) 7.5 (.689). (.874) 38. (.500) 47.6 (.874) (.03) (.063) (.89) (.3) (.406) (.75) (.689) (3.063) (.000) (3.500) (.437) (4.89) (.75) (4.75) (.063) (5.6) 8.8 (.6) 8.8 (.6) (.433) (.433) (.433) (.47) 3.5 (.53) 3.5 (.53) 3.5 (.53) 7.5 (.689) 7.5 (.689) 7.5 (.689) (.8) (.8) (.8) 38 (.50) 38 (.50) 38 (.50) 48 (.89) 38 (.50) 38 (.50) 38 (.50) (.39) 4.5 (.39) (.86) mass is the value including socket head cap screws. 7.8 (.70). (.874) 7.7 (.09) 7.7 (.09).5 (.8) 43. (.70) 49. (.933) 49. (.933) 6. (.406) 77. (3.0) 90.0 (3.543).8 (4.047) 5.5 (4.547) Q 9 (.) (.47) (.47) (.7) 8 (.7) 0 (.79) (.87) 5 (.98) 8 (.) 3.5 (.4) S 3 (.5) 9 (.75) 6 (.0) 38 (.50) 48 (.89) 5 (.0) 63 (.48) 76 (.99) 88 (3.46) (3.98) M8 40 g. 5/6-8UNC -3/4 g. SO-NB-P M8 40 g. 5/6-8UNC -3/4 g. M8 45 g. M 45 g. 3/8-6UNC -3/4 g. M 45 g. 3/8-6UNC -3/4 g. M 55 g. /-3UNC -/4 g. M 55 g. /-3UNC -/4 g. M 55 g. /-3UNC -/4 g. M 65 g. /-3UNC -3/4 g. M6 55 g. 5/8-UNC -/4 g. M6 55 g. 5/8-UNC -/4 g. M6 55 g. 5/8-UNC -/4 g. SO-NB-G SO-NB-G M 55 g. 3 (.6) 7/6-4UNC -/4 g. SO-NB-G50 SO-NB-G60 SO-NB-G65 SO-NB-G75 SO-NB-G85 SO-NB-G0 SO-NB-G5 Max. Operating MPa (PSI) (0) 8 4 (0) 4 (0) 4 (0) (50).5 (50) 7 (0) 3.5 (5) 3.5 (5) 3.5 (5) 0.5 (.) 0.7 (.5) 0.9 (.0). (.7).5 (3.3).8 (3.7).7 (3.8).0 (4.4).7 (6.0) 3.4 (7.5) 3.7 (8.) No.9

10 "J" Dia. Through D "5" Series Pipe lange its Butt Welding Japanese "JIS" & uropean : 5- -C- N. American : 5- -C-90 N Mounting Surface Surface should have a good machined finish. H "Q" Dia. "S" Dia. Max. it Numbers Dimensions mm (Inches) D H J N Q S C- M8 g (.5) / (.3) (.689) (.500) (.6) (.54) (.5) SO-NB-P 5-04-C (.85) 5/6-8UNC -/4 g. (.58) 5-06-C- 6 M g. 3/ (.89) (.56) (.874) (.874) (.433) (.6) (.75) SO-NB-G 9. (.75) (.07) 5-06-C-90 3/8-6UNC -/ g. (.75) 5-08-C- 6 M g (.7) (.03) (.063) (.433) (.65) (.) (.0) SO-NB-G 9. (.75) 5-08-C-90 3/8-6UNC -/ g. (.75) 5--C- 6 M g. -/ (.433) (.5) (3.5) (.89) (.3) (.73) (.68) (.6) 9. (.75) 5--C-90 7/6-4UNC -/ g. (.47) (.75) 5--C- 8 M 40 g. -/ (.7) (3.70) (.406) (.75) (.53) (.97) (.87) (.9) (.50) SO-NB-G50 5--C /-3UNC -/ g. 5-6-C- 8 M 40 g (.7) (3.) (4.0) (.689) (3.063) (.53) (.97) (.87) (.38) (.0) SO-NB-G C /-3UNC -/ g. 5-0-C- 0 M 45 g. -/ (.79) SO-NB-G75 (4.0) (4.49) (.000) (3.500) (.53) (.97) 9.5 (.98) (3.00) (.48) 5-0-C-90 (.77) /-3UNC -3/4 g. No. mass is the value including socket head cap screws. Recommended Tightening Torque or it Numbers Tightening Torque Recommendation Nm (IN.lbs.) Tolerance 5-04-C (3) 5-06-C 5-08-C 68.5 (660) 5--C ±% 5--C 5-6-C 8 (44) 5-0-C Note: The values of tightening torque above apply to when these flanges are used for pressure line. Max. Operating MPa (PSI) (50) 7.5 (540) 4 (0) 0.5 (.6) 0. (.8) 0.45 (.0) 0.63 (.4).3 (.9).3 (.9).4 (3.)

11 "6" Series Pipe lange its Threaded : 6- -A Socket Welding : 6- -B Up to 4 MPa (6090 PSI) Mounting Surface : SA J58 (Port Dimensions or Bolted lange, High Series) Specifications Model Numbers 6- -A- -/80/ B- -/90 Max. Operating MPa (PSI) 3 (4500) 4 (6090) Remarks Threaded Pipe Socket Welding Threaded Socket Welding Model Number ation - Material of Seal 6 Series Number -06 lange -A Type of Pipe -M Type of Mounting Bolt - Number s 04W, 04 06W, 06 08W, 08 W, W, M: Japanese "JIS" NBR (Buna N) Seal 04W, 04 06W, 06 08W, 08 W, W, A: Threaded M: 80: uropean 6 04W, 04 06W, 06 08W, 08 W, W, U: Unified Thd. 90: N. American : PM (Viton) Seal (or Synthetic luids) 04W, 04 06W, 06 08W, 08 W, W, 04W, 04 06W, 06 08W, 08 W, W, B: Pipe Socket Welding M: U: Unified Thd. Japanese "JIS" & uropean 90: N. American Three different design standards are available as shown below. Select the suitable design standard to your requirement. Type of Pipe Threaded Pipe Socket Welding Japanese "JIS" uropean N. American Japanese "JIS" & uropean N. American Pipe Thread Rc BSP. NPT Mounting Bolt ( ) Unified Thd. Unified Thd. No.

12 "6" Series Pipe lange its Threaded Japanese Std. "JIS" & N.American Std. Japanese "JIS" : 6- -A-M- N. American : 6- -A-U-90 "J" Dia. Through Mounting Surface D H "N" Dia. Max. Soc. Head Surface should have a good machined finish. Model Numbers Dimensions mm (Inches) D H J N Recommended Tightening Torque (Tolerance ±%) Nm (IN.lbs.) 6-04W-A-M A-M- 6-04W-A-U A-U-90 Rc 3/8 Rc / 3/8 NPT / NPT 48 (.89) 56.5 (.) 8. (.77) 40.5 (.594) 8.8 (.6) 8 (.) 6 (.0) (.47). (.48) 5 M8 40 g. 5/6-8UNC -/ g. SO-NB-P 0.4 (.9) (3) 6-06W-A-M A-M- 6-06W-A-U A-U-90 Rc / Rc 3/4 / NPT 3/4 NPT 57.5 (.6) 77.5 (3.05) 3.8 (.937) 50.8 (.000) (.433) (.8) M 45 g. 3/8-6UNC -3/4 g. SO-NB-G 0.9 (.0) 68.5 (606) 6-08W-A-M A-M- 6-08W-A-U A-U-90 6-W-A-M- 6--A-M- 6-W-A-U A-U-90 6-W-A-M- 6--A-M- 6-W-A-U-90 -/4 NPT 6--A-U-90 Rc 3/4 Rc 3/4 NPT NPT Rc Rc -/4 NPT -/4 NPT Rc -/4 Rc -/ -/ NPT 65 (.56) 7 90 (3.54) 8 (3.9) 95 (3.74) 3 (4.45) 7.8 (.094) 3.8 (.5) 36.5 (.437) 57. (.5) 66.7 (.66) 79.4 (3.6) 3.5 (.53) 3.5 (.53) 7.5 (.689) (.8) (.) 6.5 (.04) (.) (.) 39 (.54) (.) 39 (.54) (.) 39 (.54) (.) 39 (.54) (.7) 6.8 (.66) (.66) 8. (.7) 3. (.9) 4.5 (.96) 6 (.0) (.) 44 (.73) M 45 g. M 50 g. /-3UNC -3/4 g. /-3UNC g. M 50 g. M 55 g. /-3UNC g. /-3UNC -/4 g. M6 55 g. M6 60 g. 5/8-UNC -/4 g. 5/8-UNC -/ g. SO-NB-G SO-NB-G50. (.4).3 (.9).5 (3.3) 8 (44) 8 (44) 87 (540). mass is the value including socket head cap screws.. The values of recommended tightening torque are for socket head cap screws. No.

13 "6" Series Pipe lange its Threaded uropean uropean : 6- -A-M-80 "J" Dia. Through D mm (.0-.0 IN.) N Mounting Surface H "P" Dia. Max. Soc. Head Surface should have a good machined finish. Model Numbers 6-04W-A-M A-M W-A-M A-M W-A-M A-M-80 3/8 BSP. / BSP. / BSP. 3/4 BSP. 3/4 BSP. BSP. Dimensions mm (Inches) D H J N (.89) (.) (.6) (3.05) 8. (.77) 3.8 (.937) (.594) (.6) (.) (.47) (.000) (.433) (.8) (.8) (.56) (3.9) (.094) (.5) (.53) 6 (.) 6-W-A-M-80 BSP (3.74) (.5) (.66) (.53) 6--A-M-80 -/4 BSP. 6-W-A-M-80 -/4 BSP (3.54) (4.45) (.437) (3.6) (.689) 6--A-M-80 -/ BSP. (.) 39 (.54) (.) 39 (.54) (.79) 0 (.79) (.87) P 5 M8 40 g. SO-NB-P M 45 g. SO-NB-G M 45 g. 6 SO-NB-G (.0) M 50 g. M 50 g. (.) M 55 g. M6 55 g. 44 SO-NB-G50 (.87) (.73) M6 60 g. Recommended Tightening Torque (Tolerance ±%) Nm (IN.lbs.) 0.4 (.9) 0.9 (.0). (.4).3 (.9).5 (3.3) (3) 68.5 (606) 8 (44) 8 (44) 87 (540). mass is the value including socket head cap screws.. The values of recommended tightening torque are for socket head cap screw. No.3

14 "6" Series Pipe lange its Pipe Socket Welding Japanese "JIS" & uropean : 6- -B-M- N. American : 6- -B-U-90 "J" Dia. Through Mounting Surface D P H "N" Dia. "Q" Dia. Max. Soc. Head Surface should have a good machined finish. Model Numbers 6-04W-B-M- 6-04W-B-U B-M B-U W-B-M- 6-06W-B-U B-M B-U W-B-M- 6-08W-B-U B-M B-U-90 6-W-B-M- 6-W-B-U B-M- 6--B-U-90 6-W-B-M- 6-W-B-U B-M- 6--B-U-90 3/8 / / 3/4 3/4 -/4 -/4 -/ Dimensions mm (Inches) D H J N P Q (.89) (.) (.77) (.594) (.6) (.6) (3.05) (.937) (.000) (.433) (.56) (3.9) (.094) (.5) (.53) (3.74) (.5) (.66) (.53) (3.54) (4.45) (.437) (3.6) (.689) (.) 6 (.0) 8 (.) 6 (.0) (.8) (.8) 6.5 (.04) (.8) (.47). (.48) (.47). (.48) (.7) (.04) (.7) 6 (.) (.) 6.8 (.66) (.66) 3. (.9) 3. (.9) 7.8 (.70). (.874). (.874) 9 (.) 7.7 (.09) (.47) 7.7 (.09) (.47).5 4 (.8).5 4 (.8) (.70) (.70) (.933) (.7). mass is the value including socket head cap screws.. The values of recommended tightening torque are for socket head cap screws. 5 6 (.0) (.) 44 (.73) M8 40 g. 5/6-8UNC -/ g. M8 40 g. 5/6-8UNC -/ g. M 45 g. 3/8-6UNC -3/4 g. M 45 g. 3/8-6UNC -3/4 g. M 45 g. /-3UNC -3/4 g. M 45 g. /-3UNC -3/4 g. M 50 g. /-3UNC g. M 50 g. /-3UNC g. M6 55 g. 5/8-UNC -/4 g. M6 55 g. 5/8-UNC -/4 g. SO-NB-P SO-NB-G SO-NB-G SO-NB-G (.9) 0.9 (.0). (.4).3 (.9).5 (3.3) Recommended Tightening Torque (Tolerance ±%) Nm (IN.lbs.) (3) 68.5 (606) 8 (44) 8 (44) 87 (540) No.4