MATERIAL SAFETY DATA SHEET

Transcription

1 MATERIAL SAFETY DATA SHEET Page 1 of 7 Issued: 01-Jan Product and Manufacturer Identification Product: Mend-It Polymer Admix Chemical Family: Compound curing agent; water-reducible acrylo-linolate Product Use: Modified emulsion concrete admixture for bonding Manufacturer: Brilliant Coatings, Inc. Tel: / PO Box 68 Fax: / Niagara Falls, NY bci@freenorth.net For Chemical Emergency - Spill, Leak, Fire, Explosion or Accident: Call CHEMTREC (day or night) Within US/Canada: Outside US/Canada: (collect calls accepted) Effects of Overexposure: 2. Hazards Identification Inhalation Eye Contact Skin Contact Ingestion Permissible Exposure Limits: Threshold Limit Value: Inhalation of vapour or mist can cause headache, nausea and irritation to the nose, throat and lungs. Direct contact with material can cause a slight irritation. Prolonged or repeated skin contact may cause slight irritation. See SECTION 11 (below) for toxicological information. Not applicable 1,000 ppm 3. Component Information Component: CAS Registry: Concentration: Acrylic Polymer Complex Non-Hazardous 55.0% 57.0% Linoglycolate Wetting Agent Non-Hazardous 8.0% 12.0% Water No % or above

2

3 7. Handling & Storage Handling: Avoid contact with eyes, skin and clothing. Wash thoroughly after handling. Keep containers tightly closed. Do not breathe vapours, mist or gas. Further Information on Storage Conditions: Keep from freezing as product stability may be affected. Stir well before using. Storage: Storage Temperature: Other Data: 1⁰ to 49⁰ Celsius (34⁰ to 120⁰ Fahrenheit) Monomer vapours can be evolved when material is heated during processing operations. See SECTION 8 (below) for types of ventilation requirements. 8. Exposure Controls / Personal Protection Exposure Limits: Exposure limits are listed below, if they exist. Eye Protection: Safety glasses with side-shields. Eye protection worn must be compatible with respiratory protection system employed. Hand Protection: Neoprene gloves may provide protection against permeation. (Gloves of other chemicallyresistant materials may not provide adequate protection.) Respiratory Protection: A respiratory protection program meeting OSHA and ANSI Z6B.2 requirements or equivalent must be followed whenever workplace conditions warrant respirator use. None required under normal operating conditions. Where vapours and/or mists may occur, wear a a properly fitted NIOSH-approved (or equivalent) half-mask, air-purifying respirator. Air-purifying respirators should be equipped with NIOSH-approved (or equivalent) organic vapour cartridges and N95 filters. If oil mist is present, use R95 or P95 filters. Protective Measures: Facilities storing or utilizing this material should be equipped with an eyewash facility. Engineering Measures: Use local exhaust ventilation with a minimum capture velocity of 100 ft/min (0.5 m/sec) at the point of vapour evolution. Refer to the current edition of "Industrial Ventilation: A Manual of Recommended Practice" published by the American Conference of Government Industrial Hygienists for information on the design, installation, use and maintenance of exhaust systems. Mend-It Material Safety Data Sheet - Page 3 of 7 01-Jan-11

4 9. Physical & Chemical Properties Appearance: Form: Colour: Odour: Liquid Milky White Acrylic ph: 9.3 to 10.2 Boiling Point/Range: Melting Point/Range: Flash Point: Lower Explosion Limit: Upper Explosion Limit: Vapour Pressure: Relative Vapour Density: Water Solubility: 100⁰ Celsius (212⁰ Fahrenheit) 0⁰ Celsius (32⁰ Fahrenheit) water Non-combustible Not applicable Not applicable 17.0 mm Hg at 20⁰ Celsius (68⁰ Fahrenheit) water <1.0 water Dilutable Relative Density: 1.00 to 1.20 Viscosity, Dynamic: Evaporation Rate: Percent Volatility: 10 to 60 mpa.s <1.0 water 52% to 54% water NOTE: The physical data presented above represent typical values and should not be constituted as a specification. Hazardous Reactions: None known. Product is stable. Materials To Avoid: 10. Stability & Reactivity There are no known materials which are incorporated with this product. Polymerization: Product will not undergo polymerization. 11. Toxicological Information No data is available for this material. The information shown is based on profiles of compositionally similar materials. Acute Oral Toxicity: LD50 rat > 5,000 mg/kg Mend-It Material Safety Data Sheet - Page 4 of 7 01-Jan-11

5

6

7