PRODUCT CATALOGUE. Aluminium Extrusion

Transcription

1 PRODUCT CATALOGUE Aluminium Extrusion

2

3 COMPANY PROFILE Established in August 2016, P.K. Metal Industries is the industrial brain child of Mr.Vishal Gaur. A civil engineer who completed his education at North cap University (previously known as ITM), he has over 6 years of experience working for parent companies in the field. He aims to revolutionise this industry with both knowledge and technology by applying his experience to create new and better opportunities for everyone. The efficiency of this enterprise can be experienced when you understand the technology and of the machinery used. For the first time MICO manufactured 900 Metric ton hydraulic press has been introduced into the manufacturing system. The results this machinery provides is outstanding and far superior to any other available in today s market scenario. This machine holds a capacity to produce Metric tons per month. From quality control to maintaining international standards the clientele of P.K. Metal Industries are receiving the best products available in the market today. 01 P.K. Metal Industries

4 CHEMICAL COMPOSITION OF WROUGHT ALUMINIUM AND ALUMINIUM ALLOYS Iron New Old Aluminium Copper Magnesium Silicon Manganese Zinc TI and for other Grain Refining Elements Chromium Remarks E1C 99.0 min Ti+V=0.07 Total impurities= E1B E1E 99.5 min Ti+V=0.07 Total impurities= NE4 Remainder Cr+Mn= NE5 Remainder Cr+Mn= HE9 Remainder E91E Remainder HE30 Remainder HE20 Remainder Remainder Remainder Remainder Remainder Others 0.03 Each total Either Mn or Cr shall be present Others each 0.05 total Others each 0.05 total Others each 0.05 total Others each 0.05 otal Remainder Remainder total 0.15 Note : 1 *Titanium and / or other grain refining elements and / or chromium may be present at the option of the supplier provided the total content does not exceed 0.3 percent 2.Compositon limits are in present maximum unless shown otherwise. P.K. Metal Industries 02

5 METALLURGICAL AND MECHANICAL DATA AND TOLERANCE IS India (new) (BS) U.K or I.S (old) ALLOY EQUIVALENTS TABLE (AA) USA (AICAN) Canada DIN Germany ASTM (JIS) Japan (AFNOR) France E1B 1050 or S A A Al-1 A E1C S A A Al-3 A-4 A E1E EC CISDIA E-A EC Al E91E 6101 D50S E-A1 mg Si-0.5 Russia GS 10B NE M57S AIMg2 GR 20A A2-Sl A-G3 AM NE S AIMg3.5 GM 40A HE S AIMg Si 0.5 GS 10A A2-S5 A-SG HE S AIMg Si Cu GS 11A A2-S HE B51S AIMg Si (NP) HE B51S AIMg Si (NP) C51S C62S TEMPER DESIGNATION TABLE INDIA OR UK U.S.A Or Canada ISO TEMPER Description of designation Annealed M F F As fabricated,as manufactured or as cast - T TD Solution heat-treated, and cold worked W T TB Solution heat-treated, naturally aged and amenable to artificial ageing P T TE Artifically aged or precipitation heat-treated WP T TF Solution heat-treated and precipitation heat- treated H-21 H-1 H2A H1 Strain hardened to specified strength H-22 H-32 H2B H3B 1/4 Hard stabilized H-24 H-34 H2D H3D 1/2 Hard stabilized H-26 H-36 H2F H3F 3/4 Hard stabilized H-28 H-38 H2H H3H Fully Hard, stabilized 03 P.K. Metal Industries

6 GENERAL INFORMATION ABOUT CATALOGUE The sections shown in this catalogue are considered standard for which dies are available with us on the date of publication and are available to customers without die charges. We are continually adding to the range of extrusion dies. If the particular section, required by you, is not given in the catalogue, please write to our Works/Branch Offices to meet your specific needs. To avoid confusion and delay in the processing of enquiries and execution of orders, correct and detailed information about the desired sections are required. All the Standard Sections given in the catalogue are generally available in alloy & Temper WP (HE 9 WP) -(IS-733 & IS-1285). Extrusions in alloys other than these would be subject to special enquiry. Please note that the sections are arranged in the increasing order of dimensions. For locating the specific Section number, refer to Index. ABOUT EXTRUSION Extrusion is a modern and very versatile method of forming Aluminium. The aluminium logs, after casting to the specified alloy are fed into the continuous log homogenizing furnace wherein it is heated to a desired temperature. The logs are then fed into hot log shear where the logs are sheared to required size billets. These are pushed under tremendous pressure, applied by a hydraulic ram, through a shaped aperture in a steel die. The die aperture may have almost any imaginable contour, thereby making it possible to produce infinite shapes and the cross sections can be sawed to the required lengths. It is possible to control the finish of the extruded sections to such a degree, during its passage through the steel die, that no further finishing maybe necessary, and if required, the part may be anodized straight away into attractive colors for higher consumer appeal. PHYSICAL PROPERTIES OF ALUMINIUM Specific Garvity-2.70 Electrical Conductivity-53 to 62% IACS Co-efficient of linear expansion-22x10-4 mm/mm/oc Thermal conductivity (at 20 oc) micro-ohm (for EC-0) Modulus of Elasticity-7 x 106 kg/cm2 P.K. Metal Industries 04

7 GENERAL INFORMATION PK.METALS EXTRUSIONS MAXIMUM CIRCUMSCRIBING CIRCLE SIZES: Solid shapes -305mm. Hollow shapes-175mm. Round Tubes-205mm. Rectangular Tube-225x50mm. MANUFACTURING TOLERANCES: Extrusions are supplied to standard commercial tolerances. Special tolerances are subject to individual enquiry. LENGTH: Unless requested for other exact lengths, material will be supplied in 3658mm (12 feet) standard length. Tolerance +/-5mm WEIGHT: The weights kg/m given in catalogue are the nominal weights. In practice, tolerance, alloy and such other factors will affect the final weight and a normal variation of + or 10% should be expected. WEIGHT CALCULATION: Section weight-kg/m=section Area(mm2) x HOW TO ORDER To avoid misunderstanding and delay in the execution of orders the following procedure is recommended: a) State P.K. Metals No. and Drawing No. b) Alloy & Temper c)length in mm d)quantity Required (Min.Order Qty Should be 500 kgs) e) Tolerance and details of mating or interlocking involved, if any. f) Whether approval of section Drawing/Samples necessary. g)mode of packing.(hdpe/wooden Box/stretch wrap) 05 P.K. Metal Industries

8 B FLAT BARS A P.K. Metal Industries 06

9 07 P.K. Metal Industries

10 ROUND RODS C HANDLE D HANDLE P.K. Metal Industries 08

11 SQUARE BARS 09 P.K. Metal Industries

12 TOWER BOLT P.K. Metal Industries 10

13 SQUARE TUBE RECTANGULAR TUBE 11 P.K. Metal Industries

14 ROUND TUBE FLUTED TUBE P.K. Metal Industries 12

15 SINGLE PARTITION DOUBLE PARTITION 13 P.K. Metal Industries

16 DOOR MIDDLE SINGLE DOOR MIDDLE DOUBLE P.K. Metal Industries 14

17 DOOR VERTICAL DOOR TOP-BOTTOM 15 P.K. Metal Industries

18 CORNER PROFILE SAMOSA PROFILE STRUCTURAL PROFILE PATTAM TUBE/ LEG PARTITION P.K. Metal Industries 16

19 HANDLE WINDOW SLIDING PROFILE- 18 MM TOP BOTTOM TOP BOTTOM SINGLE LEG INTERLOCK MIDDLE/METTING 17 P.K. Metal Industries

20 HANDLE WINDOW SLIDING PROFILE- 50X25 MM TOP BOTTOM TOP BOTTOM SINGLE LEG INTERLOCK MIDDLE P.K. Metal Industries 18

21 2 TRACK TOP WINDOW SLIDING PROFILE- 18 MM 2 TRACK BOTTOM 3 TRACK TOP 3 TRACK BOTTOM 4 TRACK TOP 4 TRACK BOTTOM 19 P.K. Metal Industries

22 WINDOW SLIDING PROFILE- 75X25 MM HANDLE TOP BOTTOM MIDDLE P.K. Metal Industries 20

23 3 TRACK TOP WINDOW SLIDING PROFILE- 25 MM 3 TRACK BOTTOM 3 TRACK TOP 21 P.K. Metal Industries

24 WINDOW SLIDING PROFILE- 30 MM 2 TRACK TOP 2 TRACK BOTTOM 3 TRACK TOP 3 TRACK BOTTOM P.K. Metal Industries 22

25 2 TRACK TOP WITH PARTITION WINDOW SLIDING PROFILE- 18 MM 2 TRACK BOTTOM WITH PARTITION 23 P.K. Metal Industries

26 HANDLE WINDOW SLIDING PROFILE- 20 MM TOP BOTTOM MIDDLE P.K. Metal Industries 24

27 WINDOW SLIDING PROFILE- 20 MM 2 TRACK TOP 2 TRACK BOTTOM 3 TRACK TOP 3 TRACK BOTTOM 25 P.K. Metal Industries

28 HANDLE MOULDING PROFILE 60X25 MM TOP BOTTOM MIDDLE TOP BOTTOM SINGLE LEG P.K. Metal Industries 26

29 HANDLE MOULDING PROFILE 80X25 MM TOP BOTTOM TOP BOTTOM SINGLE LEG 27 P.K. Metal Industries

30 MIDDLE MOULDING PROFILE L TUBE L TUBE P.K. Metal Industries 28

31 Z LINE CASEMENT WINDOW PROFILE 38 MM Z HOLLOW Z BOX MULLION 29 P.K. Metal Industries

32 DOMAL SLIDING PROFILE SERIES 27 MM CLIP 2 TR TOP 3 TR TOP P.K. Metal Industries 30

33 DOMAL SLIDING PROFILE SERIES 27 MM CLIP H BOTTOM TRACK 31 P.K. Metal Industries

34 Z FRAME FRAME MULLION CLIP CLIP P.K. Metal Industries 32

35 CURTAIN WALL PROFILE 33 P.K. Metal Industries

36 CURTAIN WALL PROFILE P.K. Metal Industries 34

37 LOUVER SECTION SINTEX U FLUSH DOOR CHANNEL 35 P.K. Metal Industries

38 P.K. Metal Industries 36

39 HANDLE MOULDING PROFILES 25 MM TOP BOTTOM INTERLOCK 37 P.K. Metal Industries

40 CASEMENT WINDOW PROFILE 34 MM P.K. Metal Industries 38

41 CASEMENT WINDOW PROFILE 40 MM 39 P.K. Metal Industries

42 P.K. Metal Industries 40

43 SR1 SR3 SR2 SR4 SR5 41 P.K. Metal Industries

44 SR6 SR7 P.K. Metal Industries 42

45 1/2 GLASS PROFILE PATTAM PROFILE 43 P.K. Metal Industries

46 P.K. Metal Industries 44

47

48 P K METAL INDUSTRIES 219, Phase 1, HSIIDC Barhi, Sonipat, Haryana Phone no: , Emil: pkmetalindustries@gmail.com