COATING SOLUTION. I-CanNano TM

Transcription

1 COATING SOLUTION 225

2 226

3 Nano Anti-Damp Coating PRODUCT DESCRIPTION: Based on Chemical Nanotechnology, the synthesized product contains specially modified Functional Nano Particles that are specially linked into a Silicon Matrix in a Solvent Base. Self-organizing Nano components form an invisible layer on the surface with excellent water and oil repellent properties. n-constrkoat is a high performance, multifunctional coating with many key functional properties combined together in one coating solution. BENEFITS & ADVANTAGES Water repellant (hydrophobic) and Dirt repellent (oleo phobic), UV Resistant, Anti-Bacterial / algae, Thermal Shock Absorption, Breathable (air can water can t pass through), It allows water to roll-off the surface forming a Brushing Effect (Self-Cleaning Effect), No dampness develops on the surface, Transparent, Easy application through Spray, Brush, Material can be cured at atmospheric temperature, Stable at varying Temperatures, Low Cleaning and Maintenance Cost, Ecologically beneficial and biologically safe, It helps to retain the quality of the surface. AREAS OF APPLICATION: Can be applied on exterior walls of buildings as TOPCOAT, buildings with Brick exterior, buildings with plaster exterior, brick Walls/Slabs, Exposed RCC, painted building exterior walls, painted building interior walls etc. This coating should be applied as topcoat over plaster/brick/ painted surfaces. APPLICATION INSTRUCTIONS Mixing/Dilution: The material does not require any mixing or dilution. Application of the material as delivered from original packaging is recommended. Cleaning of the Surface: It must be ensured that the surface is free of all loose particles/ Dust etc. Before application of the coat the Plaster/ Brick/ Painted Surface should be cleaned and completely dried. Application of Coating Solution: The material can be applied on the surface by either by Spray, Brush, Roller etc. It should be ensured that the material is adequately applied until the surface is saturated (This may vary for different 227

4 surfaces, usually rough & absorbing surfaces may consume more material than smooth surfaces. On an average, a liter of the coating material should be sufficient for about 150 Sq Ft.). Application Conditions: Ambient temperature: Coating can be applied in ambient temperature conditions (i.e. 10 Deg C to 40 Deg C). Humidity level: 60% to 80%. Deviating conditions can influence the formation of hydrophobic effect and drying time. Coating should be applied and dried in a dust free environment, if possible, in clean room conditions. Application should be avoided under high humid/moist/rainy conditions. Curing: The Coating takes about 6 Hrs to completely set. Test of Coating: Once coated the performance can be tested by pouring some water on the coated panels. If properly coated, the water should form droplets and roll-off. VISCOSITY: 15 sec SPECIFIC GRAVITY: 0.81 COLOR: Transparent STORAGE: Shelf life is of at least 12 months in sealed original packing. In case of overstepping, the quality of the material should be tested again. The material should be protected against heat, frost and moisture. PACKING: 1/10/50 Liters 228

5 Nano Stone Coating PRODUCT DESCRIPTION: Based on Chemical Nanotechnology, this synthesized product contains specially modified Functional Nano Particles that are specially linked into a Silicon Matrix in a Solvent/water Base. Self-organizing Nano components form an invisible layer on the surface with excellent water and oil repellent properties. NANO STONE COATING is very versatile. It has special additional properties like UV protection and anti-bacterial protection BENEFITS & ADVANTAGES: Water repellent (hydrophobic) and Dirt repellent (oleo phobic), Properties such as UV Resistance, Anti-Bacterial property are incorporated, The water rolls-off the surface forming a Brushing Effect (Self-Cleaning Effect), Easy application through Spray/Brush, Material can be cured at atmospheric temperature, Stable at varying temperatures. Low Cleaning and Maintenance Cost. It is ecologically beneficial and biologically safe, It retains the quality of the surface, It provides resistance against: Dirt, Algae, etc. AREAS OF APPLICATION: Buildings with Stone exterior, Buildings with stone interior, Stone Sculptures, Stone Walls, Stone Slabs, dholpur/ yellow/jaisalmer/natural/black/marble stones etc. are all potential areas for the application of this material. APPLICATION INSTRUCTIONS Mixing/Dilution: The material requires no mixing or dilution. The material can be applied directly as delivered from original packaging. Cleaning of Surface: It must be ensured that the surface is free of all loose particles/ dust etc. Before application the Stone/ Brick Surface must be clean and completely dry. Application Conditions: Ambient temperature: Coating can be applied in ambient temperature conditions (i.e. 10 Deg C to 40 Deg C). In this case, drying time would be around 3 hours. Humidity level: 60% to 80%. Deviating conditions can influence the formation of hydrophobic effect and drying time. Coating should be applied and dried in a dust free environment, if possible, in clean room conditions. Application of coating should be avoided under high humid/moist/rainy conditions. Application of Coating Solution: The material can be applied on the surface by either by Spray, Brush, Roller etc. It should be ensured that the material is adequately applied until the surface is saturated (This may vary for different surfaces, usually rough & absorbing surfaces may consume more material than 229

6 smooth surfaces. On an average, a liter of the coating material should be sufficient for about Sq Ft). Solvent based coating and water based coating should be applied for smooth and rough surfaces respectively. Test of Coating: The Coating takes about 6 Hrs to completely set. Once coated the performance can be tested by pouring some water on the coated panels. If properly coated, the water should form droplets and roll-off. VISCOSITY: 15 sec SPECIFIC GRAVITY: 0.81 COLOR: Transparent/white STORAGE: Shelf life is of at least 24 months in sealed original packing. In case of overstepping, the quality of the material should be tested again. The material should be protected against heat, frost and moisture. PACKING: 1/10/50 Liters 230

7 Nano Ceramic Coating PRODUCT DESCRIPTION: Based on Chemical Nanotechnology, this synthesized product contains specially modified Functional Nano Particles that are specially linked into a Silicon Matrix in a Solvent Base. Self-organizing Nano components form an invisible layer on the surface with excellent Water/Dust Repulsion & Anti-bacterial properties. Product n-cerkoat is high performance multifunctional coating with many key functional properties combined together in one coating solution. BENEFITS & ADVANTAGES: It is a stain-free, Water repellant (hydrophobic), Dirt repellent (oleo phobic), Anti-Bacterial / algae/ foul, Scratch Resistant, Anti-sticking, Anti-corrosive, and an easy clean product. It permits water to roll-off the surface forming a Brushing Effect (Self-Cleaning Effect). Other benefits provided by this product hail from its ability to avoid dampness on the surface and its transparency. Easy application through Spray/Brush, curing at atmospheric temperature, stability at varying temperatures, low cleaning and maintenance costs and the fact that this product is ecologically beneficial and biologically safe makes this product perfectly tailored for industry usage. It also helps to retain the quality of the surface. AREAS OF APPLICATION: Areas of application include Ceramic wall tiles, Ceramic sanitary wares, Ceramic bath-wares, Ceramic Wash-Basins, Ceramic Commode/ Urinals, Water-less urinals. UNSUITABLE FOR: Plaster, natural stone, metal or plastic surfaces. APPLICATION INSTRUCTIONS Mixing/Dilution: No mixing or dilution of material should be done. The material should be delivered directly from original packaging. Cleaning of the Surface: It must be ensured that the Surface is free of all loose particles/ dust etc. Before application the ceramic surface must be clean and completely dry. This coating should be applied as topcoat over ceramic surfaces. Application of Coating Solution: The material can be applied on the surface by either Spray, Brush, Roller, Sponge, Tissue paper etc. It should be ensured that the material is adequately applied until the surface is saturated (This may vary based on efficiency of applicator. On an average, a liter of the coating material should be sufficient for about 700 Sq Ft.). Application conditions: Between + 10 C (283 K) and + 40 C (313 K) air and object temperature; dew temperature should be taken into account when working at low temperatures. Relative Humidity level should lie between 60% and 80%. Application process needs to be done in clean & dust-free environment. Application should be avoided in moist/ humid & rainy environment. 231

8 Curing: The coating takes about 3 Hrs to get set completely. Polishing: After 3 hours the surface should be wiped out with a clean & dry tissue paper and should then be polished till it becomes completely dry. Testing: Once coated the performance can be tested by pouring some water on the coated tiles. If properly coated, the water should form droplets and roll-off. CLEANING & MAINTENANCE OF THE COATED SURFACE: Periodically scaly residues, deposited salts and dirt must be removed with a nylon brush, if necessary, mild detergents may also be used. Use of strong detergents and alkali for cleaning purposes is strictly prohibited. TOUCH UP & RE-COAT: Existing coatings need not be removed; surface should be prepared as per above instructions and then recoated. VISCOSITY: 15 sec SPECIFIC GRAVITY: 0.81 COLOR: Transparent CHEMICAL RESISTANCE TESTS Name of Strength BIS Standard BIS+ Standard Chemical Condition Result Condition Resul t Acetic Acid 10% 16 hrs, 100 Deg C 72 hrs, 100 deg C Citric Acid 10% 16 hrs, 100 Deg C 72 hrs, 100 deg C Detergent hrs, 60 Deg C 72 hrs 100 deg C Hydrochloric Acid 50% 48 hrs, Deg C 72 hrs, 35 deg C Sodium Hydroxide 5% ½ hrs, 60 Deg C 24 hrs, 100 deg C Sodium Stearate 0.15% 48 hrs, 60 Deg C 72 hrs, 100 deg C Sulphuric Acid 3% 16 hrs, 100 Deg C 72 hrs, 100 deg C STAIN RESISTANCE TESTS BIS Standard Result 0.5% Methyl Blue Soln.. No stain 10% Sodium Hypochlorite. No stain. 3% Hydrogen Peroxide. No stain. Amyl Acetate Carbon Tetrachloride Iodine with ethanol. No stain.. No stain.. No stain. OTHER TESTS Test Result 232

9 Contact Angle of water droplets Thickness of coating (Dektak Profilometer) 53 0 A Abrasion Resistance Improved Cold Test ( -20ºC for 2 Hrs.) Bake Test (130ºC for 2 Hrs.) Anti-bacterial Test No bacteria growth Humidity Test ( 50ºC & 99.99% RH for 360hrs) Salt Spray (Keep the coated tiles at 5% NaCl salt chamber for 360 hrs) Water immersion test (immersed in water for 360 hrs at room temp.) Boil Test (Boil the coated ceramic tiles at 100ºC for 2 Hrs.) Temperature withstand ability Above Scratch Resistance Improved Contact angle post abrasion test No significant change UV Radiation Test (2 sun intensity for 100 Hrs.) Acid Test (ph=1) & Alkaline Test (ph=11) STORAGE: Shelf life is of at least 12 months in sealed original packing. In case of overstepping, the quality of the material should be tested again. The material should be protected against heat, frost and moisture. PACKING: 0.5/1/10 Liters 233

10 Nano Glass Coating PRODUCT DESCRIPTION: Based on Chemical Nanotechnology, the synthesized product n- glaskoat contains specially modified Functional Nano Particles that are specially linked into a Silicon Matrix in a Solvent Base. NANO GLASS COATING material, when applied on Glass surface forms a thin layer with excellent Roll-Off behavior for water, simplifying the removal of dirt and scaly residues. BENEFITS & ADVANTAGES: Water repellent (hydrophobic) and Dust repellent, Provides UV Protection, Conserves Air-Condition Load Protects glass from corrosion (acid rain etc.) and silicon oil formation, anti-glare, improved visibility, Easy application through spraying, polishing, immersion, smearing etc., Optically neutral (colorless, transparent), Allows curing at room temperature. Stable at varying temperatures, Low Cleaning and Maintenance requirements, It helps to retain the quality of the surface It is ecologically beneficial & biologically safe, It provides resistance against: Dirt, Algae, Scales etc. AREAS OF APPLICATION: Glass facades/ Glass roofs, Window panels/glass doors, Frosted glass, Decorative glass, Glass shower cabins, Automobile glass, all exterior glasses, architectural glasses, Solar PV & Thermal Panels are some of the areas where this material can be applied. APPLICATION INSTRUCTIONS Mixing/Dilution: No mixing or dilution of the material is required. The material can de applied directly as delivered from original packaging. Cleaning of the Glass Surface: Prior to application it must be ensured that the glass surface is free from all loose particles/ dust etc. If the glass surface is very dirty or oily (Fingerprints/Stains) it must be cleaned with a cleaner (detergent wash/acetone). If glass has been stored over a longer period of time, it must be cleaned e.g. a glass washing line. That the glass surface is clean and completely dry, should be ensured, if necessary, it should be wiped with little acetone. Application Conditions: Ambient temperature: Coating can be applied in ambient temperature conditions (i.e. 10 Deg C to 40 Deg C). In this case, drying time would be 234

11 around 3 hours. Humidity level: 60% to 80%. Deviating conditions can influence the formation of hydrophobic effect and drying time. Coating should be applied and dried in a dust free environment, if possible, in clean room conditions. Application of coating solution: Small quantity of the material has to be applied on the Glass Surface (Approximately about 15 ml/m 2, the exact amount need to be determined on site by a simple Roll Off Test). Material can be applied by Spraying, Brushing, Rolling, Dipping or Smearing using soft cloth/tissue paper/sponge. It is recommended to apply the material in small sections for efficient coating. That the glass surface is saturated with coating solution needs to be ensured. Curing: The coating should be allowed to dry naturally for about 3 hours or the coating may be dried by placing the glass at ambient temperature of 80 to 125 Deg C. If drying process is natural and if the coating, due to different climatic conditions, does not dry up even after about 3 hrs, then it needs to be wiped off/ polished until it completely dries out. Polishing: The material once applied need to be polished in circular motion using clean & dry soft cloth/tissue paper. This can be done by polishing/ rubbing in circular motions until it is completely rubbed off/dries out. Polishing the material at least once is recommended in order to ensure the quality of the surface. Test of Coating: Once coated, performance can be tested by pouring some water on the coated panels. If coating is done properly, water should form droplets and rolloff the glass surface and should not spread out into an uniform film. CLEANING & MAINTENANCE OF THE COATED SURFACE: The coated surface should be periodically cleaned with water only. Detergents or alkaline solutions should preferably be avoided. TOUCH UP & RE-COAT: Existing coatings need not be removed; surface should be prepared as per the above instructions and then subsequently recoated. REMOVAL OF COATING: Acetone should be used for removal of coating. VISCOSITY: 10 sec SPECIFIC GRAVITY: 0.78 COLOR: Transparent 235

12 TEST RESULTS Test Result Contact Angle of water droplets Thickness of coating 53 0 A Light Transmission (Transmitivity) No Change Abrasion Resistance Improved Optical Distortion No Change Secondary Image Separation No Change Identification of Colors No Change Cold Test Bake Test UV Radiation Test Humidity Test Cyclic Test Water immersion test Boil Test Wiper Test More than 330 hrs. Temperature withstand ability Above Scratch Resistance Improved Thermal Insulation U value No Change in U value Contact angle post abrasion test No significant change UV Protection 60% blocking of UV Rays STORAGE: Shelf life is of at least 12 months in sealed original packing. In case of overstepping, the quality of the material should be tested again. The material should be protected against heat, frost and moisture. PACKING: 0.1/1/10/50 Liters 236

13 Nano Leather Coating PRODUCT DESCRIPTION: Based on Chemical Nanotechnology, the synthesized product contains specially modified Functional Nano Particles that are specially linked into a Silicon Matrix in a Solvent Base. NANO LEATHER COATING material, when applied on leather surface forms a thin layer with excellent roll-off behavior for water, simplifying the removal of dirt and scaly residues and imparting anti-bacterial and anti-fungal behaviour. BENEFITS & ADVANTAGES: Water repellent (hydrophobic) and Dust repellent, Provides UV Protection, Conserves Air-Condition Load Easy application through spraying, polishing, immersion, smearing etc., Optically neutral (colorless, transparent), Allows curing at room temperature. Stable at varying temperatures, Low Cleaning and Maintenance requirements, It helps to retain the quality of the surface It is ecologically beneficial & biologically safe, It provides resistance against: Dirt, Algae, Scales etc. This product provides anti-bacterial effect AREAS OF APPLICATION: All clean and dry leather surfaces. APPLICATION INSTRUCTIONS Mixing/Dilution: No mixing or dilution of the material is required. The material can de applied directly as delivered from original packaging. Cleaning of the Surface: Prior to application of the coating it must be ensured that the surface is free from all loose particles/ dust etc. If the leather surface is very dirty or oily (Fingerprints/Stains) it must be cleaned with a cleaner (detergent wash/acetone). If leather has been stored over a longer period of time, it must be cleaned. That the leather surface is clean and completely dry, should be ensured, if necessary, it should be wiped with little nano leather cleaner. Application Conditions: Ambient temperature: Coating can be applied in ambient temperature conditions (i.e. 10 Deg C to 40 Deg C). In this case, drying time would be around 3 hours. Humidity level: 60% to 80%. Deviating conditions can influence the formation of hydrophobic effect and drying time. Coating should be applied and dried in a dust free environment, if possible, in clean room conditions. Application of coating solution: Small quantity of the material has to be applied on the Leather Surface (Approximately about 15 ml/m 2, the exact amount need to be 237

14 determined on site by a simple Roll Off Test). Material can be applied by Spraying, Brushing, Rolling, Dipping or Smearing using soft cloth/tissue paper/sponge. It is recommended to apply the material in small sections for efficient coating. That the leather surface is saturated with coating solution needs to be ensured. Curing: The coating should be allowed to dry naturally for about 3 hours or the coating may be dried by placing the leather at an ambient temperature of 80 to 125 Deg C. If drying process is natural and if the coating, due to different climatic conditions, does not dry up even after about 3 hrs, then it needs to be wiped off/ polished until it completely dries out. Polishing: The material once applied need to be polished in circular motion using clean & dry soft cloth/tissue paper. This can be done by polishing/ rubbing in circular motions until it is completely rubbed off/dries out. Polishing the material at least once is recommended in order to ensure the quality of the surface. Test of Coating: Once coated, performance can be tested by pouring some water on the coated panels. If coating is done properly, water should form droplets and rolloff the leather surface and should not spread out into a uniform film. CLEANING & MAINTENANCE OF THE COATED SURFACE: The coated surface should be periodically cleaned with water only. Detergents or alkaline solutions should preferably be avoided. TOUCH UP & RE-COAT: Existing coatings need not be removed; surface should be prepared as per the above instructions and then subsequently recoated. REMOVAL OF COATING: Nano Leather Cleaner should be used for removal of coating. VISCOSITY: 10 sec SPECIFIC GRAVITY: 0.78 COLOR: Transparent 238

15 TEST RESULTS Test Result Contact Angle of water droplets Thickness of coating 53 0 A Abrasion Resistance Improved Optical Distortion No Change Identification of Colors No Change Cold Test Bake Test UV Radiation Test Humidity Test Cyclic Test Water immersion test Boil Test UV Stability 300+hrs. Temperature withstand ability Above Scratch Resistance Improved Thermal Insulation U value Change in U value incurred Contact angle post abrasion test No significant change UV Protection 70% blocking of UV Rays Antibacterial Effect Very high STORAGE: Shelf life is of at least 12 months in sealed original packing. In case of overstepping, the quality of the material should be tested again. The material should be protected against heat, frost and moisture. PACKING: 1/10/50 Liter 239