TECHNICAL DATA SHEET
|
|
- Penelope Jones
- 6 years ago
- Views:
Transcription
1 PRODUCT : UT105 TWO-PACK ACRYLIC STRUCTURED METALLIC COLOURS Page 1 of 5 DESCRIPTION PROPERTIES COLOUR GLOSS LEVEL WEATHERING CHEMICAL RESISTANCE SOLVENT RESISTANCE ABRASION RESISTANCE TEMPERATURE RANGE : UT105 2-pack topcoat is an unmodified acrylic polyurethane available in a range of fine, medium and coarse metallic colours, designed to maintain maximum appearance the maximum length of time. Its principal application areas are f the decation and protection of kitchens, auto-refinish, buses, marine craft, signage, CFC panelling and masonry. : 20 Chart colours. Matchings on request. : Semi Gloss. Can be adjusted by gloss of clear coat. : Excellent : From -30 C Up to 150 C (dry) TECHNICAL DATA RECOMMENDED FILM BUILD : 100 (wet) 40 (dry) VOLUME SOLIDS : 40% THEORETICAL COVERAGE : approximately 10 metres 2 per litre at 100 wet. COMPONENTS : Two. MIXING RATIO : 4 parts Part A : 1 part Part B by volume DRYING AT 25 C : Touch dry:2 hours Handleable: 6 hours Recoat :4 hours Full cure : 5 days Curing times are adversely affected by excessive paint film thickness, improper surface preparation, improper drying conditions and increct thinner selection. UT100 Thinner is suitable f use at air temperatures up to 25 C UT101 Medium Thinner is suitable f use at air temperatures exceeding 25 C f larger and/ me complex areas. UT102 Flow Thinner is suitable f use at air temperatures exceeding 30 C f large and/ me complex areas. These three different thinners may be cross blended to give the required properties needed to suit the application and/ prevailing weather conditions. Consult the manufacturer f special circumstances.
2 Page 2 of 5 TECHNICAL DATA (continued) CHEMICALLY ASSISTED DRYING AT 25 C Touch dry : 1 hour Handleable : 3 hours Recoat : 2 hours Full cure : 3 days POT LIFE AT 25 C : 8 hours APPLICATION METHODS : Air airless spray. Chemically assisted drying requires air atomisation shaping air. FLASHPOINT : 23 C SHELF LIFE : 12 months (minimum) in iginal sealed containers PACKAGING : Part A 1litre, 4 litre, 20 litre Part B 1 litre, 5 litre SUBSTRATE PREPARATION COATING SEQUENCE FILM BUILD WET (DRY) STEEL Abrasive blast (10-15) Clean AS class2.5 (min) 1 st coat : BC300 2-pack Metal Etch 1 st coat : EP210 2-pack Anticrosive 150 (75) GALVANISED STEEL ALUMINIUM G.R.P. Degrease and mechanically abrade. New gal may require acid wash Degrease thoughly. Abrade if necessary. Remove mould release degrease. 1 st coat : BC300 2-pack Metal Etch (30-40) (40-48) 40 (10) (30-40) (30-40) ( 40-48). * Note that a final clear coat is optional, but strongly recommended to enhance appearance and to offer maximum protection.
3 Page 3 of 5 SUBSTRATE PREPARATION COATING SEQUENCE FILM BUILD WET ( DRY ) TIMBER * * UT100/UT105 on externally exposed timber - not recommended Sand and remove dust. 1 st coat : UT300 UT310 2-pack Timber Sealer. 2 nd coat :UT220 UT240 2-pack Sanding Undercoat. 1 st coat :UT220 UT240 2-pack Sanding Undercoat. 30 CFC PANELS/ MASONRY Remove dust, oil, grease and loose material from aged surfaces. UT100 Series Acrylic Topcoat (40-48) (40-48) * Note that a final clear coat is optional, but is strongly recommended to enhance appearance and to offer maximum protection. SURFACE PREPARATION STEEL GALVANISED STEEL OR ALUMINIUM CFC/MASONRY : Remove any grease oil using suitable solvent water based degreaser. Acid alkali presence should be neutralised with appropriate products followed by though rising with clean water. Any other feign matter, eg. rust, mill-scale & etc., should be abrasively blast cleaned to Australian standard AS class2.5 f ambient conditions class 3 f immersion conditions. : Remove any grease oil using suitable solvent water based degreasers. (See AS ). Mechanical abrasion and dust off should follow. : Acid wash new masonry surfaces using dilute hydrochlic acid. Wash with fresh water and allow to fully dry. CFC should be dry sanded and all dust loose surface material blown away with dry clean compressed air.
4 SURFACE PREPARATION (continued) Page 4 of 5 TIMBER / M.D.F. G.R.P : Sand de-nib and dust off pri to sealing. : Remove any grease, oil mould release using suitable solvent water based degreaser. Allow to dry thoughly befe coating. APPLICATION MIXING THINNING SPRAYING AIRLESS EQUIPMENT CLEANUP : Stir each of the components till homogenous. Mix all base and hardener components until fully blended. Allow induction time of mins pri to commencing application. F smaller quantities mix 4 parts of base to 1 part hardener by volume. : Use recommended thinner only, up to a maximum of 20% by volume depending on method of application employed. : Conventional pressure pot: 1.5 mm Fluid ifice using 385 kpa (50 psi). Pressure at pot : 65 kpa (10 psi) Pressure at Gun : 385 kpa (50 psi) : Standard airless equipment using 28.1pump ratio and fluid tip range ( inches) and supply air at kpa (80-100p.s.i). Thin as necessary with UT100 Thinner. : All equipment should be thoughly cleaned with UT100 Thinner
5 Page 5 of 5 PRECAUTIONS SAFETY : Provide adequate ventilation during use. Airflow should be adequate to ensure a comftable wking atmosphere. When spray painting, users should comply with the provisions of the State Spray Painting Regulations. Where this is not possible, operats must use an air supplied respirat complying with Australian Standards AS1715 and AS1716. This product is flammable and all sources of ignition (flames, pilot lights, furnaces, spark producing switches, etc.) must be eliminated in, near the application area. DO NOT SMOKE. This product is poly-isocyanate catalysed and all the necessary precautions must be observed when handling this type of material. Avoid contact with skin and eyes. Wear protective goggles and gloves when handling the material. In the case of skin contact, remove contaminated clothing and wash skin thoughly with clean water. Seek medical attention if eyes are affected by splashes fumes. GENERAL DANGEROUS GOODS : Freshly mixed material must NOT be added to material which has been in use f some time. Rate of cure is dependent upon temperature. Do not apply this product at temperatures below 10 C relative humidities above 85%. Ensure maximum recoat interval is not exceeded otherwise surface must be lightly abraded and then dusted to ensure maximum inter-coat adhesion. Shelf life is nmally12 months in iginal sealed containers, but depends on stage conditions. Part A Class 3.1 UN 1263 PAINT HFP Part B Class 3.2 UN 1866 PAINT HFP This data sheet is based on infmation in BC Coatings possession at date of issue. BC Coatings supplies its products only on condition that the consumer is satisfied as to the perfmance of the product in meeting his particular requirements
TECHNICAL DATA SHEET
Page 1of 5 PRODUCT DESCRIPTION PROPERTIES COLOUR GLOSS LEVEL WEATHERING UT100 2-Pack topcoat is an unmodified acrylic polyurethane designed to maintain maximum appearance for the maximum length of time.
More informationProduct Information CHEMGLAZE B 9942 A/B. Coating for Casting Pits. Easy Application Chemglaze B 9942 A/B will bond to damp and wet surfaces.
Product Information Chemical Products Division CHEMGLAZE B 9942 A/B Coating for Casting Pits. FEATURES BENEFITS. Easy Application Chemglaze B 9942 A/B will bond to damp and wet surfaces. Will build to
More informationCarboguard 890 PRODUCT DATA SHEET SELECTION & SPECIFICATION DATA. Generic Type. Cycloaliphatic Amine Epoxy
SELECTION & SPECIFICATION DATA Generic Type Description Features Color Finish Primer Cycloaliphatic Amine Epoxy Highly chemical resistant epoxy mastic coating with exceptionally versatile uses in all industrial
More informationProperty Test/Standard Description. semi gloss (35-70) Flash point ISO 3679 Method 1 32 C
Approved 18420;18360 1,2 18420 epoxy ^(ValidationDate) 1 Product description This is a two component amine cured, glass flake reinforced, abrasion resistant epoxy coating. It is a surface tolerant, high
More informationProperty Test/Standard Description
Approved 612;617 1,2 617 epoxy ^(ValidationDate) 1 Product description This is a two component, polyamide cured, high molecular weight epoxy coating. Designed as a primer for new construction. Can be used
More informationPre-qualification testing in accordance with NORSOK M-501, Rev. 5, System 1, suitable for exterior exposure in offshore environment, below 120 C.
Approved 402;2521 1,2 2521 zinc epoxy ^(ValidationDate) 1 Product description This is a two component polyamide cured zinc rich epoxy coating. It is a very high zinc dust containing product. It conforms
More informationProperty Test/Standard Description
Approved 720 1,2 720 silicone acrylic ^(ValidationDate) 1 Product description This is a one component physically drying silicone acrylic coating. It is heat resistant up to 600 C. Can be used as primer,
More informationSIGMACAP MASTIC GF. September surface tolerant coating for lower grade of steel preparation
5 pages DESCRIPTION PRINCIPAL CHARACTERISTICS COLOURS AND GLOSS BASIC DATA AT 20 C Mass density Volume solids VOC (supplied) Recommended dry film thickness Theoretical spreading rate Touch dry after Overcoating
More informationTested in accordance with ISO , high expected durability in corrosivity category C5-I. Property Test/Standard Description
Approved 7461;7680 1,2 7680 zinc epoxy ^(ValidationDate) 1 Product description This is a two component polyamide cured zinc rich epoxy coating. It is a high solids, high zinc dust containing product. It
More informationRefer to Substrates & Surface Preparation.
SELECTION & SPECIFICATION DATA Generic Type Description Features Color Finish Primer Dry Film Thickness Aliphatic Acrylic Polyurethane Thin film, high gloss finish with exceptional weathering performance
More informationProperty Test/Standard Description
Approved 1505;1506 1,2 1505 phenolic/novolac epoxy ^(ValidationDate) 1 Product description This is a two component polyamine cured phenolic/novolac epoxy coating. It is heat resistant up to 205 C (401
More informationProperty Test/Standard Description
Approved 515;519;527;1549 1,2 515 epoxy mastic ^(ValidationDate) 1 Product description This is a two component polyamine cured epoxy mastic coating. It is a surface tolerant, high solids, high build product.
More informationProperty Test/Standard Description
Approved 1537 1,2 1537 alkyd ^(ValidationDate) 1 Product description This is a one component oxidatively drying alkyd coating. It is a fast drying, high build, zinc phosphate pigmented product. Can be
More informationDate of issue: 5 October 2017 Page: 1/6
Approved 16560;16561;16840 1,2 16560 epoxy mastic ^(ValidationDate) 1 Product description This is a two component polyamine cured epoxy mastic coating. It is a surface tolerant, abrasion resistance, high
More informationCorlar 2.1 PR-P High Solids Productive Epoxy Primer
Corlar 2.1 PR-P High Solids Productive Epoxy Primer GENERAL DESCRIPTION A high solids, two component, VOC conforming (2.1 lbs./gal.) Low HAPS productive primer based on Axalta modified polyamide epoxy
More informationProperty Test/Standard Description
Approved 29560;29561 1 29560 zinc silicate ^(ValidationDate) 1 Product description This is a two component ceramically reinforced polyamide cured zinc rich epoxy coating. 1:1 mixing ratio for easy use
More informationCorlar 2.1 PR-P High Solids Productive Epoxy Primer For Use With FG-040, FG-041 or FG-042 Activators
Corlar 2.1 PR-P High Solids Productive Epoxy Primer For Use With FG-040, FG-041 or FG-042 Activators GENERAL DESCRIPTION A high solids, two component, high build, VOC conforming (2.1 lbs./gal.) Low HAPS
More informationApproved. Property Test/Standard Description. matt (0-35) Flash point ISO 3679 Method C calculated VOC-US/Hong Kong. US EPA method 24 (tested)
Approved 28780 1,2 28780 acrylic ^(ValidationDate) 2 Product description This is a one component water borne acrylic emulsion coating. It is a versatile, fast drying product for exterior and interior use.
More informationApproved. Property Test/Standard Description. gloss (70-85) Flash point ISO 3679 Method 1 32 C calculated VOC-US/Hong Kong. US EPA method 24 (tested)
Approved 30060;30061 1,2 30060 polyurethane ^(ValidationDate) 1 Product description This is a two component chemically curing aliphatic acrylic polyurethane coating. It has a glossy finish with very good
More informationProperty Test/Standard Description. US EPA method 24 (tested) (CARB(SCM)2007, SCAQMD rule 1113, Hong Kong)
Approved 402;2522 1,2 2522 zinc epoxy ^(ValidationDate) 1 Product description This is a two component polyamide cured zinc rich epoxy coating. It is a high zinc dust containing product. It conforms to
More informationPRODUCT GUIDE: ZINC-RICH COATINGS. Version:
PRODUCT GUIDE: ZINC-RICH COATINGS Version: 08.07.17 305 Zinc Rich Epoxy Polyamide Primer Description: 305 is a user friendly zinc-rich epoxy primer formulated for use as a primer under acrylic, epoxy,
More informationProperty Test/Standard Description
Approved 16480;18120 1,2 16480 polyurethane ^(ValidationDate) 1 Product description This is a two component chemically curing aliphatic acrylic polyurethane coating. This product contains no solvents on
More informationAerodur CF Primer 37047
AkzoNobel Aerospace Coatings Technical Data Sheet Product Group Polyurethane Primers Characteristics Product Information is a 3-component chromate free isocyanate cured modified polyurethane primer for
More informationApproved. Property Test/Standard Description. matt (0-35) Flash point ISO 3679 Method F (29 C) calculated VOC-US/Hong Kong
Approved 20920;16620 1 20920 epoxy ^(ValidationDate) 1 Product description This is a two component amine cured epoxy coating. It is a fast drying, zinc phosphate pigmented, high solids, high build product.
More informationNormadur 65 HS. Technical Data PROPERTIES AND RECOMMENDED USAGE TECHNICAL DATA
Technical Data Normadur 65 HS PROPERTIES AND RECOMMENDED USAGE Paint type: NORMADUR 65 HS is a fast drying, flexible polyurethane coating with an aliphatic isocyanate curing agent. NORMADUR 65 HS is high-solid
More informationtwo component high build amine adduct cured phenolic epoxy primer
5 pages Revision of January 2003 DESCRIPTION two component high build amine adduct cured phenolic epoxy primer PRINCIPAL CHARACTERISTICS primer coat in the Sigma Phenguard tank coating system excellent
More informationAliphatic Acrylic-Polyester Polyurethane
SELECTION & SPECIFICATION DATA Generic Type Description Features Color Finish Primer Dry Film Thickness Aliphatic Acrylic-Polyester Polyurethane High build, low sheen finish that has excellent resistance
More informationTechnical Data Jotamastic 80 MIO
Technical Data Jotamastic 80 MIO Product description Jotamastic 80 MIO is a high solids two-pack micaceous iron oxide pigmented, surface-tolerant epoxy mastic coating which can be applied in low film thickness.
More informationProduct Information D8120
Product Information High Solids 2-Pack Clearcoat PRODUCTS Deltron Clear Deltron s D803, D841, D861 Deltron Accelerated D863 Deltron s D870, D807,D872, D873 Deltron DG Fade-out D868 For matt, satin and
More informationDULUX INTERIOR LUXURIOUS SILK TECHNICAL DATA SHEET Version SEPTEMBER THIS ISSUE SUPERSEDES ALL PREVIOUS PUBLICATIONS
TECHNICAL DATA SHEET Version 1 2016 SEPTEMBER THIS ISSUE SUPERSEDES ALL PREVIOUS PUBLICATIONS PRODUCT DESCRIPTION A low odour premium quality interior mid sheen finish with supreme stain resistance. PRODUCT
More informationApproved. Property Test/Standard Description. high gloss (85+) Flash point ISO 3679 Method 1 30 C. US EPA method 24 (tested)
Approved 9600;9620 1,2 9600 polysiloxane ^(ValidationDate) 1 Product description This is a two component chemically curing polysiloxane resin based coating. The product does not contain isocyanates and
More informationProperty Test/Standard Description. semi gloss (35-70) Flash point ISO 3679 Method 1
2080;2081 1 2080 epoxy VValidationDate). 1 Product description This is a two component polyamide cured epoxy coating. It is a high solids, high build product. Designed as a mid coat in systems for new
More informationTECH MANUAL TABLE OF CONTENTS
PRO-SPRAY TECH MANUAL TECH MANUAL TABLE OF CONTENTS SURFACE CLEANERS 1-1 ICR-0014, ICR-0015, ICR-1402 1-1 SELF-ETCHING & EPOXY PRIMERS 2-1 A-514 CHROMATE FREE ETCH PRIMER 2-1 A-518 EPOXY PRIMER 2-3 PLASTIC
More informationApproved. Property Test/Standard Description. gloss (70-85) Flash point ISO 3679 Method 1 25 C calculated VOC-US/Hong Kong. US EPA method 24 (tested)
Approved 612;625;627 1,2 625 epoxy ^(ValidationDate) 1 Product description This is a two component polyamide cured epoxy coating. It has a glossy finish with fair gloss retention. To be used as topcoat
More informationProduct Information. DiamondCoat Polyurethane Concrete Floor Finish Clear, high build, high abrasion resistant, decorative concrete floor coating
Product Information DiamondCoat Polyurethane Concrete Floor Finish Clear, high build, high abrasion resistant, decorative concrete floor coating Description Crommelin DiamondCoat Polyurethane Concrete
More informationProperty Test/Standard Description. Flash point ISO 3679 Method C
Other Technical Data Sheet 2906;2907 6 2906 VValidationDate). 1 Product description This is a two component finishing filler. It is a smooth multi purpose product. It has good sanding properties, strong
More informationProperty Test/Standard Description. gloss (70-85) Flash point ISO 3679 Method C VOC-EU EU VOC Directive 2004/42/CE (theoretical) 14 g/l
Approved 29980;29981;30062 1,5 29980 epoxy ^(ValidationDate) 1 Product description This is a two component amine cured solvent free epoxy coating. It is a high performance product. It is easy to apply.
More informationCorlar LV PR 178 Series Epoxy Primer
Corlar LV PR 178 Series Epoxy Primer GENERAL DESCRIPTION A two-component very low VOC corrosion-resistant epoxy primer designed to be extremely tough and durable. When properly activated, the combined
More informationAPPLICATION GUIDELINES EXTERIOR DECK SYSTEM
APPLICATION GUIDELINES EXTERIOR DECK SYSTEM Revision 6 Issue Date: 15 th September 2015 Registered Office The AkzoNobel Building, Wexham Road, Slough, SL2 5DS Page 1 CONTENTS Page 1. SCOPE AND PURPOSE
More information- Aromatic hydrocarbons - Binder 2,67 kg/dm³ (±0,06 Kg/dm³) Solid content - 80% by weight (±2%) - 58% by volume (±2%) according to ASTM D2697
p. 1/6 ZINGA The Film Galvanising System ZINGA is a one pack coating that contains 96% zinc in the dry film and provides cathodic protection of ferrous metals. It can be used as a unique system as an alternative
More informationGRIP-GARD PLUS BRUSH / ROLL ADDITIVE
Description The GRIP-GARD PLUS Brushing/Rolling Additive is designed to convert GRIP-GARD PLUS spray paint into a coating that can be used for brush & roll application. 100 Grip Gard Plus (High Gloss)
More informationCorlar 2.8 HG High Solids Epoxy
Corlar 2.8 HG High Solids Epoxy GENERAL DESCRIPTION A high build, high solids, two-component, VOC conforming (2.8 lbs./gal.), high gloss epoxy based on Axalta modified polyamide epoxy technology. The resulting
More informationApproved. Property Test/Standard Description. gloss (70-85) Flash point ISO 3679 Method C VOC-US/Hong Kong. US EPA method 24 (tested)
Approved 25760;26000 1,5 25760 epoxy ^(ValidationDate) 1 Product description This is a two component amine cured solvent free epoxy coating. It is a high performance product. It is a self smoothing, easy
More informationThe Application Guide offers product details and recommended practices for the use of the product.
Technical Data Sheet Application Guide Approved 720 1,2 720 silicone acrylic ^(ValidationDate) 1 Product description This is a one component physically drying silicone acrylic coating. It is heat resistant
More informationRUST TRAP TECHNICAL DATA SHEET
RUST TRAP TECHNICAL DATA SHEET Check local VOC DESCRIPTION Rust Trap is a high gloss, moisture cured, urethane coating for restoring and protecting rusty metal. FEATURES Premium moisture-cured urethane
More informationPRODUCT DATA SHEET Sika Unitherm Platinum
PRODUCT DATA SHEET Solvent free, ultra high build, two pack, modified epoxy resin based, intumescent fire protection coating for internally or externally exposed structural steel. Ideal for in-shop application.
More informationNFCA 400 Field Quality Assurance Procedure for Application of Mastic and Thin-Film Intumescent Fire Resistive Coatings
NFCA 400 Field Quality Assurance Procedure for Application of Mastic and Thin-Film Intumescent Fire Resistive Coatings 1 Scope The application of mastic and thin-film intumescent fire resistive coatings
More informationTechnical Data Sheet S Topcoats LV 351 TOPCOAT MM/RM FOR PROFESSIONAL USE ONLY
100 Topcoat 40 Hardener 30 Reducer Description: High gloss, state of the art 2K High Solids polyurethane topcoat. The target use for this product is refinishing and refurbish of existing vehicles and the
More informationEclipse ECL-G-2 Clear High Solids Polyurethane Topcoat
Technical Data Sheet Product Group Polyurethane topcoat Characteristics Product Information ECL-G-2 is a high solids, long life clear coat formulated for use with Eclipse base coat and special effect colors
More informationNEXA AUTOCOLOR 2K Plastics Painting Process
PDS N7.1 April 2017 NEXA AUTOCOLOR 2K Plastics Painting Process PRODUCT DESCRIPTION The NEXA AUTOCOLOR 2K Plastic Painting Process offers a complete and high quality rage of products for the painting of
More informationHS High-Build, Primer Surfacer P /1028. HS High-Build, Primer Surfacer P / Grey / White
Product Data Sheet February 2018 INTERNATIONAL MASTER FOR PROFESSIONAL USE ONLY Product P565-1027/8 Product Description HS High-Build, Primer Surfacer P565-1027 /1028 - Grey / White Description HS High
More informationDulux AcraTex Roof Sealer SB Clear
Dulux AcraTex Roof Sealer SB Clear AUDA0476 Part A 194-85752 Image Product Overview Previously known as DULUX AcraTex 501/4 Roof Sealer DULUX AcraTex Roof Sealer Solvend Based is a solvent based, deep
More informationSECTION High Performance Coatings Field Applied Acrylic Urethanes (Solid Color, Pearl and Metallic Finishes)
- 1 - SECTION 099600 High Performance Coatings Field Applied Acrylic Urethanes (Solid Color, Pearl and Metallic Finishes) PART 1 GENERAL 1.1 SECTION INCLUDES A. Systems for field applied acrylic urethane
More information1.4 kg/l (11.4 lb/us gal) Maximum 295 g/kg (Directive 1999/13/EC, SED) Maximum 420 g/l (3.5 lb/gal) 50 to 63 μm (2.0 to 2.
DESCRIPTION One-component, heat-resistant silicone acrylic topcoat primarily for the PPG HI-TEMP 1027 primer or the PPG HI-TEMP 222 G primer. PRINCIPAL CHARACTERISTICS Heat-resistant silicone acrylic topcoat
More information3MTM FireDamTM Intumescent Coating WB Installation Manual. Thinner is. Better
0808-3086E 3M FD Intumescent Coating WB 1000 - INSTALLATION MANUAL:Layout 1 9/30/08 2:32 PM Page 1 3MTM FireDamTM Intumescent Coating WB 1000 Installation Manual Thinner is Better 3 1 Index 1. Product
More informationProduct Data Sheet Waterproofing Membrane for Ponds and Water Features Description Uses Suitable Surfaces Additional Uses Specification
Product Data Sheet Pondseal Waterproofing Membrane for Ponds and Water Features Description Pondseal is a polyurethane / acrylic co-polymer, water based coating which when fully cured, forms an impervious,
More informationGood properties on otherwise difficult to bond substrates. High impact resistance over a wide temperature range
Advanced Materials Araldite 2047-1 Structural Adhesives TECHNICAL DATA SHEET Araldite 2047-1 Methacrylate adhesive requiring minimal surface pretreatment Key properties Gap filling Good properties on otherwise
More informationDP4101 / DP4104 / DP4107 HS PRIMER
Description 2-component High Solids primer with 2 methods of application: a. primer surfacer; b. non-sanding primer. Colour: white, medium grey and black. Composition based on a special hydroxy functional
More informationSP-100 Equipment Wash SP-110 Tool Cleaner SP-120 Internal Storage Lubricant
DESCRIPTION: SP-9888 Pipe Lining is based on the latest Zero VOC Novolac Technology. The product cures to a highly cross-linked coating with excellent chemical, solvent and water immersion resistance.
More informationTT-P-1757B Type I, Class C, Aerosol Zinc Chromate Primer. A one component, alkyd base, corrosion inhibiting zinc chromate primer.
941 111313 TT-P-1757B Type I, Class C, Aerosol Zinc Chromate Primer PRODUCT: TT-P-1757B TY.I, CL.C AEROSOL ZINC CHROMATE PRIMER A one component, alkyd base, corrosion inhibiting zinc chromate primer. DESCRIPTION:
More informationASTEC ANTI-GRAFFITI CLEAR COATING POLYURETHANE SILICONE MODIFIED TYPE. Aliphatic 2 Pack Polyurethane Anti-graffiti coating. PRODUCT DESCRIPTION
[ TECHNICAL BULLETIN ] ASTEC ANTI-GRAFFITI CLEAR COATING POLYURETHANE SILICONE MODIFIED Sumolac PRODUCT TYPE Aliphatic 2 Pack Polyurethane Anti-graffiti coating. PRODUCT DESCRIPTION Astec Sumolac is a
More informationRUST TRAP TM TECHNICAL DATA SHEET
RUST TRAP TM TECHNICAL DATA SHEET Check local VOC DESCRIPTION Rust Trap is a moisture cross- linked urethane for coating ferrous metals. Rust Trap also adheres to aluminum, fiberglass and properly prepped
More informationHYDRAULIC GATE SEALS. Industrial Rubber Supply (1995) Ltd.
Industrial Rubber Supply (1995) Ltd. Manufacturers of Quality Industrial Products 55 Dunlop Avenue, Winnipeg, Manitoba, Canada R2X 2V2 Phone (204) 694-4444 - Fax (204) 632-6767 - www.indrub.com ISO 9001:2000
More informationCROMAX PRO WB9908 SUPER JET BLACK BASECOAT
CROMAX PRO WB9908 SUPER JET BLACK BASECOAT GENERAL DESCRIPTION A super jet black factory package color that delivers the deepest black to meet the most critical color standards. It features high hiding,
More informationTwo component PU adhesive system. Property 2018/A 2018/B 2018 (mixed)
Advanced Materials Araldite 2018 Structural Adhesives TECHNICAL DATA SHEET Araldite 2018 Two component PU adhesive system Key properties Good UV stability Ideal for bonding thermoplastics Low shrinkage
More informationUse suitable respiratory protection Akzo Nobel Car Refinishes recommends the use of a fresh air supply respirator
Description Autobase Plus basecoat provides excellent coverage, metallic control and sprayability when used to duplicate OEM solid, metallic and pearl colour effects. Autobase Plus must be used in conjunction
More information2K P421 - Single Layer Metallic System Medium Solids. P421-2K Single-layer Metallic colour mixes. P K Air dry lacquer converter
FOR PROFESSIONAL USE ONLY I0320 Date of Issue : July 2002 2K P421 - Single Layer Metallic System Medium Solids Products P421-2K Single-layer Metallic colour mixes P420-/P421-/P425-/P429-2K Mixing basics
More informationEpiMax 999WB Concrete Protective Sealer
EpiMax 999WB Concrete Protective Sealer Description EpiMax 999WB Concrete Protective Sealer is a hazmat free, two component water based clear epoxy coating system specially formulated to provide ease of
More informationOne-coat application 5 LV650 Clear 2 LV650 Hardener 1 LV650 Reducer Anti-Graffiti (#484165)
Description Autocoat BT is a two component VOC compliant clear coat that provides excellent chemical resistance and stain repellent properties. is designed for original equipment and repairs of commercial
More informationGently shake the Autowave can prior to use. Prior to clearcoat application: Until completely matt at 25 C 15 minutes at 25 C
Description Autowave waterborne basecoat provides excellent coverage, metallic control and sprayability when used to duplicate OEM solid, metallic and pearl effect colors. Autowave must be used in conjunction
More information5 STAR XTREME AUTOBODY PRODUCTS TECHNICAL DATA INFORMATION DATED: FEBRUARY 2017 PRODUCT NUMBER DESCRIPTION #5180 ORIGINAL KLEARKOTE 2.
5 STAR XTREME AUTOBODY PRODUCTS TECHNICAL DATA INFORMATION DATED: FEBRUARY 2017 PRODUCT NUMBER DESCRIPTION #5180 ORIGINAL KLEARKOTE 2.1 VOC PRODUCT DESCRIPTION 5180 is a medium solids two component polyurethane
More informationTECHNICAL DATA SHEET
Dy-Mark EPOXY COAT WATER-BASED DIRECTIONS FOR USE Dy-Mark All-In-One Epoxy Coat Water-Based is a fast dry floor coating that gives a professional finish to interior bare concrete floors. Epoxy Coat resists
More informationApplication Guide AC- 130 Metal Alloy Surface Preparation For Bonding
Application Guide AC- 130 Metal Alloy Surface Preparation For Bonding SCOPE This document describes the process for the application of AC- 130 pre-bond surface treatment to facilitate adhesive bonding
More information10P20-14 High Solids Low IR Primer
Technical Data Sheet Product Group Epoxy Primer Characteristics Product Information - A high solids primer for aircraft exteriors meeting the low infrared reflectance requirements of the referenced specification.
More informationTECHNICAL DATA SHEET
Dy-Mark EPOXY COAT DIRECTIONS FOR USE Dy-Mark All-In-One Epoxy Coat is a durable floor coating that gives a professional finish to interior bare concrete floors. Epoxy Coat resists hot tyre pick-up and
More informationConcrete Protective Sealer
Concrete Protective Sealer Description EpiMax 999WB Concrete Protective Sealer is a hazmat free, two component water based clear epoxy coating system specially formulated to provide ease of application,
More informationEnvironmentally responsible
Product range guide Intergrain Enviropro uses advanced water based polyurethane technology to bring you a high performance range of interior timber floor coatings. Being low VOC and low odour makes Enviropro
More informationE P CONCRETE BLOCK SEALER
earth friendly chemistry E P CONCRETE BLOCK SEALER E P latest waterproofing product. Utilising advanced ACRYLIC technology, combined with Polyester Polymer. This formula outperforms all other aliphatic
More informationPRODUCT SELECTION GUIDE
PRODUCT SELECTION GUIDE Floor Sealers MasterTop 333 MasterKure 402 MasterKure 404 MasterTop 1116 Mastertop TC 406 Mastertop TC 450 Mastertop TC 471 Mastertop TC 495 Single Pack Two-pack Epoxy Polyurethane
More information1.4 kg/l (11.4 lb/us gal) Maximum 272 g/kg (Directive 1999/13/EC, SED) Maximum 420 g/l (3.5 lb/gal) To 650 C (1200 F) To 538 C (1000 F)
DESCRIPTION One component heat resistant silicone topcoat for use in an elevated temperature coating system, primarily for application over PPG HI-TEMP 1027 primer PRINCIPAL CHARACTERISTICS Heat resistant
More informationSikaCor 255 Epoxy-binder for mortars on concrete and steel. Protective Coatings
Product Data-Sheet Edition 03.09 DS-Code: E 1605 SikaCor 255 Epoxy-binder for mortars on concrete and steel SikaCor 277 Thixotropic epoxy-binder - sag resistant high-build coatings and mortars Protective
More informationInstruction Guide APPLICATION OF CIM TO CONCRETE
23 Elm St., Peterborough, NH 03458 Tel: (800) 543-3458 (603) 924-9481 Fax: (603) 924-9482 Web site: Instruction Guide APPLICATION OF CIM TO CONCRETE 1.0 DESCRIPTION This guide covers the installation of
More informationAPPLICATION GUIDELINES RAPID REPAIR EXTERIOR DECK SYSTEM
APPLICATION GUIDELINES RAPID REPAIR EXTERIOR DECK SYSTEM Revision 6 Issue Date: 15 th September 2015 Registered Office The AkzoNobel Building, Wexham Road, Slough, SL2 5DS Page 1 CONTENTS Page 1. SCOPE
More informationHEAD OFFICE 22 Park Drive Dandenong VIC Phone: (03) Fax (03)
Technical Data Sheet Unitex Polymer Render Unitex Polymer Render is an acrylic polymer-rich wet render for thin trowel-applied one coat applications with the highest adhesion and flexibility that Unitex
More informationSAMPLE SPECIFICATION
SAMPLE SPECIFICATION Section 02760 Paving Specialties STREETCOAT Epoxy Modified Traffic Coating System IDEAL FOR VEHICULAR TRAFFIC, BIKE LANES AND COATING STAMPED ASPHALT SURFACES 1.0 GENERAL 1.1 Summary
More informationMETAL & MACHINERY PAINT POLYURETHANE FLOOR PAINT SKIP & CONTAINER PAINT
Master Paints WE VE GOT IT COVERED Master Paints WE VE GOT IT COVERED MASTERBUILD PRODUCTS LTD MOORSIDE MILL, CHURCH STREET, AINSWORTH, BURY BL2 5RD TEL: +44 (0)161 763 8600 FAX: +44 (0)161 763 8606 www.masterbuildproducts.co.uk
More informationCHROMAPREMIER 42400S / 42410S / 42440S / 42470S 2K PREMIER SEALER
CHROMAPREMIER 42400S / 42410S / 42440S / 42470S 2K PREMIER SEALER GENERAL DESCRIPTION A three-component, high-performance sealer for premium-quality spot, panel and overall repairs. It provides excellent
More informationSEMPEO SQA Unit Code FP46 04 Finishing surfaces by applying coatings or coverings
Overview This standard covers a broad range of basic competences that you need, to apply specified surface finishes by the application of coatings or coverings. It will prepare you for entry into the engineering
More informationJanuary 2007 Product Information ENVIROBASE HIGH PERFORMANCE
GLOBAL REFINISH SYSTEM January 2007 Product Information ENVIROBASE HIGH PERFORMANCE PRODUCTS Envirobase Waterborne Basecoat colour T4xx Envirobase Thinner T494 Envirobase High Performance is waterborne
More informationSILASEC DESCRIPTION FEATURES AND BENEFITS SURFACE PREPARATION
SILASEC WP0001 REVISED: JANUARY 2002 DESCRIPTION Bondall Silasec is a concentrated liquid waterproofing compound designed to be used with Portland type A or type GP cements to form a permanent waterproof
More informationRust Bullet Home and Farm FAQ s
Rust Bullet Home and Farm FAQ s 1. Will Rust Bullet Protect My Galvanized Metal Roof? Yes. Rust Bullet is the ideal coating for protecting sheet metal buildings and roofs; it not only provides protection
More informationPOLYMER CONCRETE 100 EPOXY POLYMER CONCRETE DILUTE ACIDS RESISTANCE
RECOMMENDED APPLICATIONS Polymer Concrete 100 is a three-component, epoxy polymer concrete used for the construction of chemical resistant floors, pads, curbing, trenches and sumps. Polymer Concrete 100
More informationAQUATITE. Also designed as: Crack/gap filler for masonry and unglazed ceramics Sealants against leaks Repairer for roof cracks and gutters
AQUATITE Revision Date: september 2007 Description Bondall AquaTite is a grey, brushable, waterproofing coating that forms a flexible yet tough, seamless membrane. This single pack product exceeds the
More informationSIDER-POOL. Product Data. Features and Uses
153 Regur Road Hawkinsville, GA 31036 USA 1.478.892.9800 888-743-3750 sales@sider-crete.com www.sider-crete.com Product Data Features and Uses A true cement-based plaster No-check cracking and no-brushing
More informationAraldite Advanced Materials. Two component epoxy paste adhesive. Structural Adhesives TECHNICAL DATA SHEET. Key properties Metal coloured paste
Advanced Materials Araldite 2013 Structural Adhesives TECHNICAL DATA SHEET Araldite 2013 Two component epoxy paste adhesive Key properties Metal coloured paste Suitable for vertical applications Low shrinkage
More informationMaximum Rust Protection!
ZERO-RUST Zero Rust is a direct-to-metal, phenolic modified alkyd rust and corrosion control coating, which controls rust and corrosion by putting down an impermeable barrier at the steel level. Its dielectric
More informationCC-1004 Ultra High Temperature Epoxy Adhesive
CC-1004 Ultra High Temperature Epoxy Adhesive PRODUCT DESCRIPTION TYPICAL USES Blome CC-1004 is a two part, high temperature, epoxy adhesive used for the installation of abrasion resistant brick and tile
More informationApplication Guidelines
International Paint Ltd Protective Coatings Application Guidelines Prepared by: PC Technical Support International Paint Ltd. www.international-pc.com The information in this guideline is not intended
More informationWater Based Epoxy Barrier Membrane, Primer & Sealer for Damp Surfaces, New Concrete
Product Data Sheet Primeseal MC Water Based Epoxy Barrier Membrane, Primer & Sealer for Damp Surfaces, New Concrete Description Duram Primeseal MC ('Moisture Cure') is a water based, epoxy waterproof membrane.
More informationAdhesion Promoter/Primer 3M Adhesion Promoter AP596
Adhesion Promoter/ 3M Adhesion Promoter AP596 3M All Purpose P591 3M Metal P592 Technical Data October 2017 Product Description 3M Adhesion Promoter AP596 and 3M s P591, P592, and are low viscosity adhesion
More information