A Low-Temperature Creep Experiment Using Common Solder

Size: px
Start display at page:

Download "A Low-Temperature Creep Experiment Using Common Solder"

Transcription

1 A Low-Temperature Creep Experiment Using Common Solder L. Roy Bunnell, Materials Science Teacer Soutridge Hig Scool Kennewick, WA Abstract: Tis experiment uses common lead-tin solder as a model material to demonstrate creep in metals at room temperature. By using two specimens loaded wit te same stress but wit different gauge lengts and under te same stress, te concept of te strain is well illustrated. Te data are plotted in a simple manner, but analysis easily sows te effect of increased stress due te reduction in specimen cross-section as strain increases. Objectives: To demonstrate creep as a penomenon in metals, witout using expensive furnaces or equipment, to reinforce te concepts of stress and strain. Student learning objectives: Students see creep actually appening, and by developing a grapical plot, realize te role of stress in determining te creep rate in a metal alloy. MatEd Core Competencies covered: 0.A Demonstrate good communication skills 0.B Prepare tests and analyze data 1.A Carry out measurements of dimensions and pysical properties 7.G Define stress and strengt 7.H Define strain and deformation 16.B Describe te effects of defects on material properties Key words: Creep, solder, stress, strain Type of Module: Laboratory Experiment Time Required: Approximately 1 week, wit experiment conducted at te front of te classroom; observation requires only a few minutes per class period, so te experiment and run concurrently wit oter instruction. Pre-requisite knowledge: Introduction to concepts of stress and strain in mecanical testing would be elpful. Target Grade Levels: 11 t -12 t grade and introductory college courses.

2 Table of Contents Equipment and Supplies Required: Solid-core lead-tin solder (no built-in flux): Te test material used in tis lab was 60/40 tin/lead solder. Be sure tat it is solid core solder wit no built-in flux. You can also try (or compare) oter solder compositions. Solder diameter used in tis experiment was 1/8 inc; larger diameters will need eavier weigts. Also: Brass weigts, meter stick, grap paper. Curriculum overview and notes for te instructor Tis experiment is a modified version, for a ig scool audience, of an experiment originally developed by Prof. Robert Stang and te University of Wasington. His approac, owever, used a tensile testing macine and matematical analysis of te data tat is beyond most introductory tecnology or ig scool classes and students. Te intent of tis work is to adapt tat experiment for use as an introduction witout te matematical finesse. In tis experiment, te mecanical testing macine is replaced by dead weigts, and te gauge lengt of te specimens is measured wen convenient, using a common meter stick. Creep is a slow extension of a material in response to a comparatively low stress. Under a constant load, extension of te material results in a reduction in cross-section area, so stress increases under constant load. Te iger te stress, te iger te creep rate until failure finally occurs. In metals, creep can occur at any temperature iger tan approximately alf te absolute melting point (Celsius melting point + 273). Tus creep is not a problem for common metals used at ordinary temperatures. By coosing te rigt alloy, owever, creep can be demonstrated at room temperature, and te creep of common lead + tin solder is te subject of tis experiment. Lead-tin solder as a melting point of 183 C (456 K), so room temperature at 298K is more tan alf te melting temperature. Tus we would expect creep to occur at room temperature in solder if it is put under sufficient stress. Tis is also wy a soldered electrical connection sould always include a mecanical connection if possible, so tat stresses on te soldered joint are minimized. Creep is also a relevant failure mecanism for ig-temperature engines, suc as jet turbines. Te need for greater efficiency and power output drives temperatures ever iger, and tis makes creep an ever-more-present failure mecanism despite our best efforts to prevent it. As an example of creep-prevention metods, consider te fact tat creep is enanced by fine-grained metals. Turbine blades in te ottest sections of today s engines are now frequently composed of a single grain, a triump of materials processing. Module Procedure: 1. Sample preparation: Te first task was to fabricate specimens tat would not fail due to end effects. One practical metod is to first allow approximately 8 inces of extra wire at eac end of a specimen, and to loop te wire twice around a piece of ¾ ardwood dowel about 1 long, wit a ¼ ole drilled lengtwise troug it (see Figure 1). Once te solder wire is looped around tis end grip, it is wrapped

3 around itself at least 6 times to preclude slippage, and about ½ in. of solder is left projecting perpendicular to te wire to be stressed (to be used as a guide in measuring te sample lengt during te experiment). Tis sould all be done by and, to avoid nicking te solder using tools. Premature failure may occur at any nicks. Te distance between te two ends is measured as a function of time, and is regarded as a gauge lengt. A total of 5 of tese specimens is suggested, four of tem wit a gauge lengt of about 6 and one wit a gauge lengt of about 18. Te longer specimen is used to sow tat te strain calculation eliminates te effect of gauge lengt. 2. Sample testing: Te creep specimens are stressed in te following manner: Specimen #1 as no added weigt on it, and is intended as a control, to sow tat creep requires a minimum stress level to occur. Specimen #2 supports a weigt of 1000 grams, producing a stress level (force/area) of about 200 pounds per square inc. Specimen 3 also supports a weigt of 1 kg, wit specimen 3 about 3 X as long as specimen 2. Specimen 4 supports a weigt of 1.5 kg (stress level about 300 psi), to illustrate te faster failure tat occurs wen te stress is proportionately iger. Finally, specimen 5 supports a weigt of 2000 g (about 400 psi) to be like #4 except more so. Note tat all of tese stress levels are rater trivial for metals, demonstrating tat te stresses do not ave to be very ig for creep to occur once you are above alf te melting temperature. In order to stress te specimens, te appropriate weigts are suspended from teir lower ends, wile te upper ends were suspended from supports at te front of te classroom. 3. Measurement and observation: After te creep experiment is started, measurements sould be taken twice per day, once in te morning and once just before leaving. Eac specimen eventually will fail at some tiny defect suc as a nick were stress was iger, and te effect of tis local overload is seen as necking, wic eventually leads to local overstressing and failure. 4. Data Recording: For convenience, te data may be recorded in an Excel spreadseet, and tis spreadseet projected at te start of eac class for students to review or copy. Strain sould be calculated for eac data point. Te formula for strain is: Strain = (gauge lengt at any time-original gauge lengt)/original gauge lengt Since te units of lengt cancel in te formula above, strain is expressed as a percentage. A sample Excel spreadseet is sown in Table 1, sowing calculated strains as a function of time for te five specimens. Strain versus time for tis example is plotted in Fig. 3. Students sould be required to plot te data in tis manner, and to explain te sapes and ordering of te curves. Note tat, as expected, te specimen wit no added weigt (#1) exibited no strain during tis experiment, and would not be expected to creep because te stress from its own weigt is below te critical creep stress at room temperature for solder. Also, note tat Specimens 2 and 3 plot almost identically even toug differing greatly in lengt, because te strain calculation automatically adjusts for sample lengt. Te creep rate of te specimen is

4 powerfully affected by stress, wit iger stress producing iger creep rates and failure in sorter times. Note also tat all te curves ave basically te same sape; tis is because, as te specimens stretc, te cross-sectional area must decrease, increasing te stress. Consistent wit te previous statement, te iger stress produces iger creep rates. Te failure time is also very sensitive to te stress level. Figure 2 sows te current ig-strain record-older, a specimen loaded wit 700 grams of weigt (stress = 110 psi) tat as not failed wile undergoing almost 600% strain. Tis strain could undoubtedly be exceeded, wit careful enoug specimen preparation, an even lower stress level, and enoug time. Tis experiment as been performed for several years at Soutridge Hig Scool, and is a good way to sow tis metal failure mecanism at minimum trouble and expense. One possible cange could be to add one more specimen, stressed by 500 grams of weigt. At tis lower stress level, failure times are often more tan a week, depending on ambient temperature. Specimen #5 could also be eliminated, since te idea of iger stress effects is conveyed by specimen #4. For comparison, oter solder compositions could be tried, as could be oter materials suc as nylon fising line. Conclusions from tis experiment: 1. Common lead-tin solder creeps at room temperature, and is tus a convenient model material to demonstrate creep in metals. 2. Strain at failure and time to failure are strongly influenced by te applied stress. Supporting Materials: see attaced Reference: Solid core solder may be available at your local ardware store. Oter options include 1. Cline Glass Co., ttp:// 2. Discount Tools, ttp:// Acknowledgement: Tis experiment is a modified version, for a ig scool audience, of an experiment originally developed by Prof. Robert Stang and te University of Wasington. Evaluation Packet: Student evaluation questions (discussion or quiz): 1. Wy is solder used for tis experiment instead of some oter metal or alloy? 2. Wy do we use strain as te measure of creep? 3. Does te lengt of te specimen determine creep beavior? 4. Wat would appen if we doubled te diameter of te specimen wit oter variable remaining te same? Instructor evaluation questions: 1. At wat grade level was tis module used? 2. Was te level and rigor of te module wat you expected? If not, ow can it be improved?

5 3. Did te lab work as presented? Did tey add to student learning? Please note any problems or suggestions. 4. Was te background material sufficient for your background? Sufficient for your discussion wit te students? Comments? 5. Did te lab generate interest among te students? Explain. 6. Please provide your input on ow tis module can be improved, including comments or suggestions concerning te approac, focus and effectiveness of tis activity in your context. Course evaluation questions (for te students) 1. Was te lab clear and understandable? 2. Was te instructor s explanation compreensive and toroug? 3. Was te instructor interested in your questions? 4. Was te instructor able to answer your questions? 5. Was te importance of materials testing made clear? 6. Wat was te most interesting ting tat you learned?

6 Figure 1. Solder Creep Specimen Ready for Use.

7 Figure 2. Higest-Strain Specimen Tested to Date; Strain is Almost 600%.

8 t=0 t=7 t=23 t=30 t=47 t=54 t=71 t=72 t=78 t=106 t=121 t=143 t=150 t=174 t=182 W=0 W=1000g W=1000g W=1500g W=700g Spec. 1 Spec. 2 Spec. 3 Spec. 4 Spec. 5 cm(0) 6.1 cm 30.9 cm 5.2 cm 4.9 cm cm(0), , , , , cm(0) 7.7, , , 2 cm(0) 8.2, , , , 4 cm(0) 9.1, , , , 18 cm(0) 9.7, , , , 14 cm(0) 10.8, , , , 20 Broke cm(0) 11.5, , , 20 cm(0) 14.7, , 83, 33 cm(0) 16.8, , , 39 cm(0) 20.9, , , 49 cm(0) 22.9, , , 49 cm(0) 29.4, , , 59 Broke, 177 cm(0) 34.8, , 63 Table 1. Typical Data Set. At eac time after test start, eac entry contains te gauge lengt at te time of measurement, ten te calculated strain at tat time.

9 Creep Strain, % Time, X 10 Series2 Series3 Series4 Series5 Series6 Fig. 3. Creep Strain in Lead-Tin Solder as a Function of Stress and Time. Series 2 is Specimen 1, wile Series 3 and 4 are Specimens 2 and 3. Series 5 is Specimen 4, and Series 6 is Specimen 5.

ANALYSIS OF TENSION MEMBERS

ANALYSIS OF TENSION MEMBERS CHATER Structural Steel Design LRFD Metod Tird Edition ANALYSIS OF TENSION MEMBERS A. J. Clark Scool of Engineering Department of Civil and Environmental Engineering art II Structural Steel Design and

More information

Forging. Types of Forging Dies. Open-Die Forging. Outline. Forging. Types of forging Forging analysis Examples

Forging. Types of Forging Dies. Open-Die Forging. Outline. Forging. Types of forging Forging analysis Examples Forging Outline Forging Types of forging Forging analysis Examples Oldest of te metal forming operations, dating from about 5000 B C Components: engine cranksafts, connecting rods, gears, aircraft structural

More information

Optimized geothermal binary power cycles

Optimized geothermal binary power cycles Optimized geotermal binary power cycles Kontoleontos E., Mendrinos D., Karytsas C. Centre for Renewable Energy Sources, 9t km Maratonos ave., 9009 Pikermi Attikis, Greece ABSTRACT Tis study as been carried

More information

SHEAR AND FLEXURAL BEHAVIOR OF FERRO CEMENT DEEP BEAMS

SHEAR AND FLEXURAL BEHAVIOR OF FERRO CEMENT DEEP BEAMS IJRET: International Journal of Researc in Engineering and Tecnology eissn: 319-1163 pissn: 31-7308 SHEAR AND FLEXURAL BEHAVIOR OF FERRO CEMENT DEEP BEAMS Md Itesam Hussain 1,Vaijanat Halalli, P.M.B Raj

More information

TECHNICAL NOTE. On Cold-Formed Steel Construction DESIGN CONSIDERATIONS FOR FLEXURAL AND LATERAL-TORSIONAL BRACING

TECHNICAL NOTE. On Cold-Formed Steel Construction DESIGN CONSIDERATIONS FOR FLEXURAL AND LATERAL-TORSIONAL BRACING TECHNICAL NOTE On Cold-Formed Steel Construction Ligt Gauge Steel Engineers Association Wasington, D.C. Toll-Free: 1 (866) 465-4732 www.lgsea.com $5.00 DESIGN CONSIDERATIONS FOR FLEXURAL AND LATERAL-TORSIONAL

More information

COMPETENCE OF PHA TEAMS

COMPETENCE OF PHA TEAMS COMPETENCE OF PHA TEAMS by Paul Baybutt paulb@primatec.com www.primatec.com Presented at te American Institute of Cemical Engineers 10t Global Congress on Process Safety New Orleans, Louisiana Marc 30

More information

The Study on Identifying the Relationship between Opportunity Recognition and Sustainability in Small Business in Sri Lanka

The Study on Identifying the Relationship between Opportunity Recognition and Sustainability in Small Business in Sri Lanka Te Study on Identifying te Relationsip between Opportunity Recognition and Sustainability in Small Business in Sri Lanka H.R.L Perera, K.T.J.C.M. Perera, B.K.U.P Rodrigo, K.M. Gunawickrama, P.V.H.N.D Perera,

More information

NUMERICAL DIFFERENTIATIONS SPREADSHEET CALCULATOR

NUMERICAL DIFFERENTIATIONS SPREADSHEET CALCULATOR Prosiding Seminar Kebangsaan Aplikasi Sains dan Matematik 2013 (SKASM2013) Batu Paat, Joor, 29 30 Oktober 2013 NUMERICAL DIFFERENTIATIONS SPREADSHEET CALCULATOR Kim Gaik ~ a ~ (Sie ', Lo~ig KekZ & Rosmila

More information

Specification Weld requirements for fillet joint by fusion welding process. - Weld requirements

Specification Weld requirements for fillet joint by fusion welding process. - Weld requirements Class: Test Instruction and conditions of delivery Specification 2017-09 Weld requirements for fillet joint by fusion welding process Class No.:61 JED 879 Previous Edition Part name (for databases) - Weld

More information

UC Berkeley Research Reports

UC Berkeley Research Reports UC Berkeley Researc Reports Title Crane Double Cycling in Container Ports: Affect on Sip Dwell Time Permalink ttps://escolarsip.org/uc/item/9qp7p7jq Autors Goodcild, Anne V. Daganzo, Carlos F. Publication

More information

Transportation Research Forum

Transportation Research Forum Transportation Researc Forum Comparison of Alternative Metods for Estimating Houseold Trip Rates of Cross-Classification Cells wit Inadequate Data Autor(s): Judit L. Mwakalonge and Daniel A. Badoe Source:

More information

AIR-VOID-AFFECTED ZONE IN CONCRETE BEAM UNDER FOUR-POINT BENDING FRACTURE

AIR-VOID-AFFECTED ZONE IN CONCRETE BEAM UNDER FOUR-POINT BENDING FRACTURE Journal of Civil Engineering and Management ISSN 139-3730 / eissn 18-3605 018 Volume 4 Issue : 130 137 ttps://doi.org/10.3846/jcem.018.456 AIR-VOID-AFFECTED ZONE IN CONCRETE BEAM UNDER FOUR-POINT BENDING

More information

Structural Change and Economic Dynamics

Structural Change and Economic Dynamics Structural Cange and Economic Dynamics 21 (2010) 5 16 Contents lists available at ScienceDirect Structural Cange and Economic Dynamics journal omepage: www.elsevier.com/locate/sced Industry dynamics in

More information

AN EXPERIMENTAL INVESTIGATION ON CHARACTERISTIC PROPERTIES OF FIBRE REINFORCED CONCRETE CONTAINING WASTE GLASS POWDER AS POZZOLANA

AN EXPERIMENTAL INVESTIGATION ON CHARACTERISTIC PROPERTIES OF FIBRE REINFORCED CONCRETE CONTAINING WASTE GLASS POWDER AS POZZOLANA AN EXPERIMENTAL INVESTIGATION ON CHARACTERISTIC PROPERTIES OF FIBRE REINFORCED CONCRETE CONTAINING WASTE GLASS POWDER AS POZZOLANA S.M. Cikalikar, Govt. of Maarastra, India S.N. Tande, Walcand, Colleg

More information

Citation for published version (APA): Riezebos, J. (2002). Time bucket size and lot-splitting approach. s.n.

Citation for published version (APA): Riezebos, J. (2002). Time bucket size and lot-splitting approach. s.n. University of Groningen Time bucket size and lot-splitting approac Riezebos, Jan IMPORTANT NOTE: You are advised to consult te publiser's version (publiser's PDF) if you wis to cite from it. Please ceck

More information

0.3 to 0.18 W/mK (depending on construction) by CSTB

0.3 to 0.18 W/mK (depending on construction) by CSTB CI/SfB Xt6 September 2017 Contents System components 2 Applications 3 resistances 4-6 considerations 7 Installation guidance 8 Isotec Termally Insulated Balcony Connectors Ancon Isotec Isotec is a ig performance

More information

Improved Fuzzy Load Models by Clustering Techniques in Distribution Network Control

Improved Fuzzy Load Models by Clustering Techniques in Distribution Network Control International Journal on Electrical Engineering and Informatics - Volume 3, Number 2, 20 Improved Fuzzy Load Models by Clustering Tecniques in Distribution Network Control George Grigoras, P.D. * and George

More information

PHASE CHANGE MATERIALS

PHASE CHANGE MATERIALS 18 TECHNOOGY REVIEW: PHASE CHANGE MATERIAS Qpedia continues its review of tecnologies developed for electronics cooling applications. We are presenting selected patents tat were awarded to developers around

More information

Comparison of Empirical Fragmentation Models at the Gol-Gohar Iron Ore Mine

Comparison of Empirical Fragmentation Models at the Gol-Gohar Iron Ore Mine In te Name of God Comparison of Empirical Fragmentation Models at te Gol-Goar Iron Ore Mine Dr. Moammad Taji 24-26 August 2015 Sydney, Australia Contents 2 Introduction Fragmentation surely is one of te

More information

Air Atomizing Design, Features & Introduction

Air Atomizing Design, Features & Introduction Atomizing Design, Features & Introduction atomizing spray nozzles produces fine mist spray wit te elp of compressed air, liquid breaks into small droplets as air provides saring effects on liquid droplets.

More information

Market basket analysis with neural gas networks and self-organising maps Received (in revised form): 3rd March, 2003

Market basket analysis with neural gas networks and self-organising maps Received (in revised form): 3rd March, 2003 Market basket analysis wit neural gas networks and self-organising maps Received (in revised form): rd Marc, 00 Reinold Decker is Professor and Head of Marketing at te University of Bielefeld, Germany

More information

Texto para Discussão. Série Economia

Texto para Discussão. Série Economia Faculdade de Economia, Administração e Contabilidade de Ribeirão Preto Universidade de São Paulo Texto para Discussão Série Economia TD-E 12 / 2011 A Importância da Organização Interna da Firma para o

More information

CE 115 Intro to Civil Eng: Geotechnical Engineering Soil Pressure Acting on Wall

CE 115 Intro to Civil Eng: Geotechnical Engineering Soil Pressure Acting on Wall CE 115 Intro to Civil Eng: Geotecnical Engineering Soil Pressure Acting on Ground Surface Soil Pressure Were: σ = soil pressure acting on wall φ k a = tan 2 45, active eart pressure coefficient 2 γ = unit

More information

HSV Carbon steel with DIN 125 washer. HSV-BW Carbon steel with DIN 9021 washer and DIN 127b spring washer

HSV Carbon steel with DIN 125 washer. HSV-BW Carbon steel with DIN 9021 washer and DIN 127b spring washer HSV Stud ancor Ancor versions HSV Carbon steel wit DIN 125 waser HSV-BW Carbon steel wit DIN 9021 waser and DIN 127b spring waser Benefits - torque-controlled mecanical expansion allows immediate load

More information

Problem Set 2 KEY

Problem Set 2 KEY 2006 7.012 Problem Set 2 KEY Due before 5 PM on FRIDAY, September 29, 2006. Turn answers in to te box outside of 68-120. PLEASE WRITE YOUR ASWERS O THIS PRITOUT. 1. You are doin a enetics experiment wit

More information

On Activity-based Network Design Problems

On Activity-based Network Design Problems UCI-ITS-WP-12-3 On Activity-based Network Design Problems UCI-ITS-WP-12-3 Jee Eun Kang Josep Y. J. Cow Will W. Recker Department of Civil Engineering and Institute of Transportation Studies University

More information

INDEPENDENT DEMAND SYSTEMS: DETERMINISTIC MODELS

INDEPENDENT DEMAND SYSTEMS: DETERMINISTIC MODELS INDEPENDENT DEMAND SYSTEMS: DETEMINISTIC MODELS A major reason for aving inventory is to enable an organization to buy or produe items in eonomi lot sizes Eonomi lot sizing often applied wen organization

More information

14. Area Optimization

14. Area Optimization 14. Area Optimization May 2013 QII52023-13.0.0 QII52023-13.0.0 Tis capter describes tecniques to reduce resource usage wen designing or Altera devices. Tis capter includes te ollowing topics: Resource

More information

WSEAS TRANSACTIONS on POWER SYSTEMS

WSEAS TRANSACTIONS on POWER SYSTEMS ESTIMATION OF LOAD DIAGRAMS IN MV/LV SUBSTATIONS J. N. FIDALGO Department of Electric Engineering and Computers Faculty of Engineering of Porto University Rua Dr. Roberto Frias, nº 378, 42-465, Porto jfidalgo@inescporto.pt

More information

Plain Concrete Tunnel Lining-Design Concepts

Plain Concrete Tunnel Lining-Design Concepts TRANSPORTATON RESEARCH RECORD 1150 15 Plain Concrete Tunnel Lining-Design Concepts RENHARD GNLSEN Discussed in tis paper are domestic and foreign concepts for te design of plain concrete tunnel lining.

More information

Poverty Effects of Higher Food Prices

Poverty Effects of Higher Food Prices Public Disclosure Autorized Policy Researc Working Paper 4887 WPS4887 Public Disclosure Autorized Public Disclosure Autorized Poverty Effects of Higer Food Prices A Global Perspective Rafael E. De Hoyos

More information

Determining Dryness Fraction

Determining Dryness Fraction Determining Dryness Fraction SUPERHEATED EVAPORATION 100 C WATER LINE 0 C g Temperature/Entalpy Dryness Fraction Tis andout assumes te student is amiliar wit Steam Tables and te terms ound terein. I required,

More information

FEM European Materials Handling Federation

FEM European Materials Handling Federation FEM European Materials Handling Federation www.fem-eur.com 0.01.017 FEM 4.005 (4t Edition) Guideline / Indurial trucks 90 acking aisle widt Tale of Contents Introduction... 3 1 Scope... 3 Normative References...

More information

A NOVEL INTEGRATED ENERGY SYSTEM OF SOLAR POWER, HEAT PUMPS AND AI-EV (AIR-CONDITIONER ELECTRIC VEHICLE)

A NOVEL INTEGRATED ENERGY SYSTEM OF SOLAR POWER, HEAT PUMPS AND AI-EV (AIR-CONDITIONER ELECTRIC VEHICLE) t International Conference on Heat Transfer, Fluid Mecanics and Termodynamics HEFAT6 t International Conference on Heat Transfer, Fluid Mecanics and Termodynamics July 6 Malaga, Spain A NOVEL INTEGRATED

More information

Consumer price indices: provisional data December 2016

Consumer price indices: provisional data December 2016 4 January 2017 Consumer price indices: provisional data December 2016 In December 2016, according to provisional estimates, te Italian consumer price index for te wole nation (NIC) increased by 0.4% on

More information

A Model for Efficiency-Based Resource Integration in Services

A Model for Efficiency-Based Resource Integration in Services University of St. Tomas, Minnesota UST Researc Online Operations and Supply Cain Management Faculty Publications Operations and Supply Cain Management 2012 A Model for Efficiency-Based Resource Integration

More information

outlines some of te potential extensions of our model. 2. Literature review As confirmed by Van den Berg et al. (2013) te personnel sceduling problem

outlines some of te potential extensions of our model. 2. Literature review As confirmed by Van den Berg et al. (2013) te personnel sceduling problem A manpower allocation problem wit layout considerations Luca Zeppetella, Elisa Gebennini, Andrea Grassi, Bianca Rimini Dipartimento di Scienze e Metodi dell Ingegneria, Università degli Studi di Modena

More information

Outflow Dynamics in Modeling Oligopoly Markets: The Case of the Mobile Telecommunications Market in Poland

Outflow Dynamics in Modeling Oligopoly Markets: The Case of the Mobile Telecommunications Market in Poland MPRA Munic Personal RePEc Arcive Outflow Dynamics in Modeling Oligopoly Markets: Te Case of te Mobile Telecommunications Market in Poland Katarzyna Sznajd-Weron and Rafal Weron and Maja Wloszczowska Hugo

More information

Biofuels Role in Mexico s Rural Development

Biofuels Role in Mexico s Rural Development Biofuels Role in Mexico s Rural Development George A. Dyer* Te James Hutton Institute Craigiebuckler, Aberdeen AB15 8QH United Kingdom george.dyer@utton.ac.uk * corresponding autor: georgie.dyer@gmail.com;

More information

Consumer prices: final data November 2017

Consumer prices: final data November 2017 14 December 2017 Consumer prices: final data November 2017 In November 2017, te Italian consumer price index for te wole nation (NIC) decreased by 0.2% on montly basis and increased by 0.9% compared wit

More information

HSV. with DIN 125 washer HSV-BW. Carbon steel. with DIN 9021 washer and DIN 127b spring washer

HSV. with DIN 125 washer HSV-BW. Carbon steel. with DIN 9021 washer and DIN 127b spring washer HSV Stud ancor Ancor versions HSV Carbon steel wit DIN 125 waser HSV-BW Carbon steel wit DIN 9021 waser and DIN 127b spring waser Benefits - torque-controlled mecanical expansion allows immediate load

More information

Design of Turbine Screw Model for Pico-Hydro

Design of Turbine Screw Model for Pico-Hydro American Journal of Engineering Researc (AJER) e-issn: 2320-0847 p-issn : 2320-0936 Volume-6, Issue-9, pp-130-140 www.ajer.org Researc Paper Design of Turbine Screw Model for Pico-Hydro Yulianto 1 *, A.Komarudin

More information

Consumer prices: final data July 2017

Consumer prices: final data July 2017 11 August 2017 Consumer prices: final data July 2017 In July 2017 te Italian consumer price index for te wole nation (NIC) increased by 0.1% on montly basis and by 1.1% compared wit July 2016, down from

More information

This article appeared in a journal published by Elsevier. The attached copy is furnished to the author for internal non-commercial research and

This article appeared in a journal published by Elsevier. The attached copy is furnished to the author for internal non-commercial research and Tis article appeared in a journal publised by Elsevier. Te attaced copy is furnised to te autor for internal non-commercial researc and education use, including for instruction at te autors institution

More information

Consumer prices: final data

Consumer prices: final data 16 January 2018 Consumer prices: final data December 2017 In December 2017, te Italian consumer price index for te wole nation (NIC) increased by 0.4% on montly basis and by 0.9 wit respect to December

More information

Consumer prices: provisional data January 2017

Consumer prices: provisional data January 2017 3 February 2017 Consumer prices: provisional data January 2017 In January 2017, according to preliminary estimates, te Italian consumer price index for te wole nation (NIC) increased by 0.2 on montly basis

More information

Inventory Planning with Batch Ordering in Multi-echelon Multi-product Supply Chain by Queuing Approach

Inventory Planning with Batch Ordering in Multi-echelon Multi-product Supply Chain by Queuing Approach Inventory Planning wit Batc Ordering in Multi-ecelon Multi-product Supply ain y ueuing Approac Eraim Teimoury, Ali Mazlomi, Raele Nadafioun, Iman G. Kondai, and Medi Fati Astract In tis paper, we apply

More information

Labor Supply with Social Interactions: Econometric Estimates and Their Tax Policy Implications

Labor Supply with Social Interactions: Econometric Estimates and Their Tax Policy Implications DISCUSSION PAPER SERIES IZA DP No. 3034 Labor Supply wit Social Interactions: Econometric Estimates and Teir Tax Policy Implications Andrew Grodner Tomas J. Kniesner September 2007 Forscungsinstitut zur

More information

Optimal Design and Operation of Energy Polygeneration Systems. Yang Chen

Optimal Design and Operation of Energy Polygeneration Systems. Yang Chen Optimal Design and Operation of Energy Polygeneration Systems by Yang Cen Submitted to te Department of Cemical Engineering in partial fulfillment of te requirements for te degree of Doctor of Pilosopy

More information

FEDERATION EUROPEENNE DE LA MANUTENTION Product Group. Industrial Trucks. Industrial trucks 90 stacking aisle width. I n d e x. Introduction...

FEDERATION EUROPEENNE DE LA MANUTENTION Product Group. Industrial Trucks. Industrial trucks 90 stacking aisle width. I n d e x. Introduction... FEDERTION EUROPEENNE DE L MNUTENTION Product Group Indurial Trucks FEM 4.005 (E Indurial trucks 90 acking aisle widt FEM-IT-T/N985 09/013 (E I n d e x Introduction... 1 1. Scope... 1. Normative references...

More information

DEVELOPING WINTER RESIDENTIAL DEMAND RESPONSE STRATEGIES FOR ELECTRIC SPACE HEATING

DEVELOPING WINTER RESIDENTIAL DEMAND RESPONSE STRATEGIES FOR ELECTRIC SPACE HEATING 12t Conference of International Building Performance Simulation Association, Sydney, 14-16 November. DEVELOPING WINTER RESIDENTIAL DEMAND RESPONSE STRATEGIES FOR ELECTRIC SPACE HEATING Leduc Marie-Andrée

More information

Experimental Analysis of Integrated System of Membrane Distillation for Pure Water with Solar Domestic Hot Water

Experimental Analysis of Integrated System of Membrane Distillation for Pure Water with Solar Domestic Hot Water Experimental Analysis of Integrated System of Membrane Distillation for Pure Water wit Solar Domestic Hot Water Muammad Asim Master of Science Tesis KTH Scool of Industrial Engineering and Management Energy

More information

THE EFFECTS OF WEATHER SHOCKS ON ECONOMIC ACTIVITY: HOW CAN LOW-INCOME COUNTRIES COPE?

THE EFFECTS OF WEATHER SHOCKS ON ECONOMIC ACTIVITY: HOW CAN LOW-INCOME COUNTRIES COPE? CHAPTER 3 THE EFFECTS OF WEATHER SHOCKS ON ECONOMIC ACTIVITY: HOW CAN LOW-INCOME COUNTRIES COPE? Global temperatures ave increased at an unprecedented pace over te past 4 years, and significant furter

More information

TEMPORARY EXCAVATION SUPPORT SYSTEM FOR A NEW RAILWAY BRIDGE AND HIGHWAY UNDERPASS IN PITTSBURGH

TEMPORARY EXCAVATION SUPPORT SYSTEM FOR A NEW RAILWAY BRIDGE AND HIGHWAY UNDERPASS IN PITTSBURGH TEMPORARY EXCAVATION SUPPORT SYSTEM FOR A NEW RAILWAY BRIDGE AND HIGHWAY UNDERPASS IN PITTSBURGH Andrew G. Cusing 1, Member, ASCE and Cristoper J. Lewis 2, P.E., Member, ASCE ABSTRACT: Until recently,

More information

Transportation Costs and U.S. Manufacturing FDI

Transportation Costs and U.S. Manufacturing FDI Marquette University e-publications@marquette Economics Faculty Researc and Publications Business Administration, College of 5-1-2014 Transportation Costs and U.S. Manufacturing FDI Josep P. Daniels Marquette

More information

New Method to Harness More Wind Energy

New Method to Harness More Wind Energy New Metod to Harness More Wind Energy M. Z. I. Sajid, K. Hema Candra Reddy & E. L Nages 1 Quba College of Engineering & Tecnology, Nellore, Andra Prades, India, 2 A & P, JNTU Anantapur, 3 Netaji Institute

More information

Co-Opetition Strategy Model of Hakkanese Culture Relics Museums

Co-Opetition Strategy Model of Hakkanese Culture Relics Museums International Journal of Management Sciences Vol. 5, No. 1, 2015, 85-101 Co-Opetition Strategy Model of Hakkanese Culture Relics Museums Maw-Cerng Lin 1 Abstract Hakkanese culture relic s museums are cultural

More information

OPTIMAL OPERATION OF AN ENERGY HUB NETWORK IN THE CONTEXT OF HYDROGEN ECONOMY

OPTIMAL OPERATION OF AN ENERGY HUB NETWORK IN THE CONTEXT OF HYDROGEN ECONOMY 6t International Conference on Hydrogen roduction UOIT Osawa, Ontario, Canada OTIMAL OERATION OF AN ENERGY HUB NETWORK IN THE CONTEXT OF HYDROGEN ECONOMY 1, 2, 3* Maroufmasat Azade, 2 Fowler Micael, 2

More information

IJISET - International Journal of Innovative Science, Engineering & Technology, Vol. 2 Issue 11, November

IJISET - International Journal of Innovative Science, Engineering & Technology, Vol. 2 Issue 11, November IJISET - International Journal of Innoatie Science, Engineering & Tecnology, Vol. Issue 11, Noember 015. ISSN 348 7968 Matematical Model of Urban Taxi Subsidy Sceme Xiao Tong 1,Wang Zuo,Yang Liucong 3,Cen

More information

POWER systems are undergoing a major transformation

POWER systems are undergoing a major transformation 1 Generic Demand Model Considering te Impact of Prosumers for Future Grid Scenario Analysis Sariq Riaz, Student Member, IEEE, Hesamoddin Marzoogi, Member, IEEE, Gregor Verbič, Senior Member, IEEE, Arcie

More information

Impact of Sampling on Small Area Estimation in Business Surveys

Impact of Sampling on Small Area Estimation in Business Surveys Impact of Sampling on Small Area Estimation in Business Surveys Jan Pablo Burgard, Tomas Zimmermann and Ralf T. Münnic University of Trier, Economic and Social Statistics Department, Universitätsring 15,

More information

AN ASSESSMENT OF VULNERABILITY TO POVERTY IN RURAL NIGERIA

AN ASSESSMENT OF VULNERABILITY TO POVERTY IN RURAL NIGERIA AN ASSESSMENT OF VULNERABILITY TO POVERTY IN RURAL NIGERIA M. A. Agbaje, F. Y. Okunmadewa, B. T. Omomona, and O. A. Oni Department of Agricultural Economics, University of Ibadan, Ibadan, Nigeria E-Mail:

More information

Prime mover sizing for base-loaded combined heating and power systems

Prime mover sizing for base-loaded combined heating and power systems 17 Prime mover sizing for base-loaded combined eating and power systems P J Mago* and R Luck Department of Mecanical Engineering, Mississippi State University, Mississippi, USA Te manuscript was received

More information

Auto landing using fuzzy logic

Auto landing using fuzzy logic 6t International PD Worksop on Systems and Control, October 4-8, 25 Izola, Slovenia INTRODUCTION Auto landing using fuzzy logic Pavle Boskoski, Biljana Mileva 2, Stojce Deskoski 3 Faculty of Electrical

More information

Design of a MSF Desalination Plant to be supplied by a New Specific 42 MW Power Plant Located in Iran

Design of a MSF Desalination Plant to be supplied by a New Specific 42 MW Power Plant Located in Iran Design of a MSF Desalination Plant to be supplied by a New Specific 4 MW Power Plant Located in Iran ouzbe Safagat, Hoda Safagat, Fateme Ganbari, Pouya Sirous ezaei and oolla Espanani Abstract Nowadays,

More information

Forestry An International Journal of Forest Research

Forestry An International Journal of Forest Research Forestry An International Journal of Forest Researc Forestry 2014; 87, 249 255, doi:10.1093/forestry/cpt061 Advance Access publication 15 January 2014 Comparing te efficiency of intensity-based forest

More information

Structural Integrity Assessment of Ferritic-Austenitic Welded Joints

Structural Integrity Assessment of Ferritic-Austenitic Welded Joints Radomir Jovičić Faculty of Mecanical ngineering Innovation Center Aleksandar Sedmak Full Professor Faculty of Mecanical ngineering Zija Burzić Military Institute, Zarkovo Vencislav Grabulov Military Institute,

More information

GISELA GIS-based Evaluation of Land-use and Agriculture Market Analysis and the Effects of Income Distribution

GISELA GIS-based Evaluation of Land-use and Agriculture Market Analysis and the Effects of Income Distribution GISELA GIS-based Evaluation of Land-use and Agriculture Market Analysis and te Effects of Income Distribution Sunsuke Mori Professor, Department of Industrial Administration, Faculty of Science and Tecnology,

More information

Simulation-based study of the energy requirements linked to the temperature control of micro-algae culture in outdoor photobioreactors.

Simulation-based study of the energy requirements linked to the temperature control of micro-algae culture in outdoor photobioreactors. Simulation-based study of te energy requirements linked to te temperature control of micro-algae culture in outdoor potobioreactors. Lorenzo Cappai 1*, Marie-Amélie de Ville d Avray 1, Ounayda Mdere 1,

More information

Available online at ScienceDirect. Energy Procedia 56 (2014 )

Available online at  ScienceDirect. Energy Procedia 56 (2014 ) Available online at www.sciencedirect.com ScienceDirect Energy Procedia 56 (01 98 308 11t Eco-Energy and Materials Science and Engineering (11t EMSES Perormance o steam production by biomass combustor

More information

MFR / MFF / MFT. Magnetic Filters and Dirt Traps : PN 40. p max. : +200 C OScrew O thread: G ¼... G 4. t max. Rp 1...

MFR / MFF / MFT. Magnetic Filters and Dirt Traps : PN 40. p max. : +200 C OScrew O thread: G ¼... G 4. t max. Rp 1... Magnetic Filters and Dirt Traps measuring monitoring analysing MFR / MFF / MFT OO p max : PN 40 OO t max : +200 C OScrew O tread: G ¼... G 4 OScrew O tread: Rp 1... Rp 2 OFlanges: O DN 50... DN 200 OSolder

More information

Design of Earth Dams. Earth Dam Components

Design of Earth Dams. Earth Dam Components Design of Eart Dams Eart Dam Components 1 Design Requirements Types of Eart Dams Oter Types of Dams Concrete Roller Compacted concrete Debris flows Coice of Type Depends on Availability of materials Trucking

More information

Are high value agri-food supply chains participants better insulated from shocks? Evidence from Senegal

Are high value agri-food supply chains participants better insulated from shocks? Evidence from Senegal WORKING PAPER NUMBER 2017/3 Are ig value agri-food supply cains participants better insulated from socks? Evidence from Senegal Sènakpon F. A. DEDEHOUANOU University of Abomey Calavi (UAC)/FASEG, Benin

More information

The strength of a material depends on its ability to sustain a load without undue deformation or failure.

The strength of a material depends on its ability to sustain a load without undue deformation or failure. TENSION TEST The strength of a material depends on its ability to sustain a load without undue deformation or failure. This strength is inherent in the material itself and must be determined by experiment.

More information

Now Available, New YNMG 2.53 Inserts. Insert Shapes YNMG Corner Radii.016",.031" Grades Cermet: PV3010 CT3000 Carbide: TT8115 (CVD) TT5080 (PVD)

Now Available, New YNMG 2.53 Inserts. Insert Shapes YNMG Corner Radii.016,.031 Grades Cermet: PV3010 CT3000 Carbide: TT8115 (CVD) TT5080 (PVD) Insert Sapes YNMG 2.53 Corner Radii.016",.031" Grades Cermet: PV3010 CT3000 Caride: TT8115 (CVD) TT5080 (PVD) Now Availale, New YNMG 2.53 Inserts Ingersoll is pleased to announce te expansion of te Gold-Rino

More information

MFR / MFF / MFT. Magnetic Filters and Dirt Traps : PN40 : +200 C. Rp1...Rp2. OO p max. OO t max. OO Screw thread: G¼...G4. OO Flanges: DN50...

MFR / MFF / MFT. Magnetic Filters and Dirt Traps : PN40 : +200 C. Rp1...Rp2. OO p max. OO t max. OO Screw thread: G¼...G4. OO Flanges: DN50... Magnetic Filters and Dirt Traps measuring monitoring analysing MFR / MFF / MFT OO p max : PN40 OO t max : +200 C OO Screw tread: G¼...G4 OO Screw tread: Rp1...Rp2 OO Flanges: DN50...DN200 OO Solder connections:

More information

Computers and Chemical Engineering

Computers and Chemical Engineering Computers and Cemical Engineering 33 (2009) 1584 1592 Contents lists available at ScienceDirect Computers and Cemical Engineering journal omepage: www.sevier.com/locate/compcemeng Predictive optimal management

More information

Assessment Protocol for the Commercial Harvest of Pacific Oysters (Crassostrea gigas) in British Columbia

Assessment Protocol for the Commercial Harvest of Pacific Oysters (Crassostrea gigas) in British Columbia Canadian Science Advisory Secretariat (CSAS) Researc Document 04/07 Pacific Region Assessment Protocol for te Commercial Harvest of Pacific Oysters (Crassostrea gigas) in Britis Columbia Tammy C. Norgard,

More information

Industrial Rolled. High Performance STOL Alloys. Characteristics

Industrial Rolled. High Performance STOL Alloys. Characteristics Page 1 Alloy Designation Hig Performance STOL Alloys EN - DIN CEN/TS 13388 - UNS JAPAN C 1510 JIS H 3100 Cemical Composition Weigt percentage Cu 99.80 % Zr 0.05.. 0.15 % Fe 0.005 % Mn 0.005 % Al 0.005

More information

STRENGTH PARAMETERS OF MASONRY WALLS IN MODELLING HISTORIC CONSTRUCTIONS

STRENGTH PARAMETERS OF MASONRY WALLS IN MODELLING HISTORIC CONSTRUCTIONS CIVIL AND ENVIRONMENTAL ENGINEERING REPORTS ISSN 2080-5187 CEER 2015; 18 (3): 055-063 DOI: 10.1515/ceer-2015-0036 STRENGTH PARAMETERS OF MASONRY WALLS IN MODELLING HISTORIC CONSTRUCTIONS Micał GOŁĘBIEWSKI

More information

DOCUMENT DE TRAVAIL

DOCUMENT DE TRAVAIL Publié par : Publised by: Publicación de la: Édition électronique : Electronic publising: Edición electrónica: Disponible sur Internet : Available on Internet Disponible por Internet : Faculté des sciences

More information

ENGINEERING MATERIAL 100

ENGINEERING MATERIAL 100 Department of Applied Chemistry Division of Science and Engineering SCHOOL OF ENGINEERING ENGINEERING MATERIAL 100 Experiments 4 and 6 Mechanical Testing and Applications of Non-Metals Name: Yasmin Ousam

More information

PRICING AND SCHEDULING STRATEGIES FOR AIR CARGO CARRIERS: A NON-COOPERATIVE GAME APPROACH

PRICING AND SCHEDULING STRATEGIES FOR AIR CARGO CARRIERS: A NON-COOPERATIVE GAME APPROACH Advanced OR and AI Metods in Transportation PRICING AND SCHEDULING STRATEGIES FOR AIR CARGO CARRIERS: A NON-COOPERATIVE GAME APPROACH Oliver F. SHYR 1, Yuan-Lu LEE Abstract. As an oligopoly maret, te pricing

More information

OPTIMIZATION FOR COGENERATION SYSTEMS IN BUILDINGS BASED ON LIFE CYCLE ASSESSMENT

OPTIMIZATION FOR COGENERATION SYSTEMS IN BUILDINGS BASED ON LIFE CYCLE ASSESSMENT OPTIMIZATION FOR COGENERATION SYSTEMS IN BUILDINGS BASED ON LIFE CYCLE ASSESSMENT SUBMITTED: Marc 2005 REVISED: January 2006 PUBLISHED: May 2006 at ttp://itcon.org/2006/20/ EDITOR: Dana J. Vanier Ayat

More information

Development of Small Hydro Power in India Awadhesh Kumar 1 Dr. ShriRam 2

Development of Small Hydro Power in India Awadhesh Kumar 1 Dr. ShriRam 2 IJSRD - International Journal for Scientific Researc & Development Vol., Issue, ISSN (online): - Development of Small Hydro Power in India Awades Kumar Dr. SriRam Post Graduate Student Associate Professor,

More information

Effect of Construction Joints on Performance of Reinforced Concrete Beams

Effect of Construction Joints on Performance of Reinforced Concrete Beams Al-Kwarizmi Engineering Journal Al-Kwarizmi Engineering Journal, Vol. 8, No. 1, PP 48-64 (2012) Effect of Construction Joints on Performance of Reinforced Concrete Beams Zena Waleed Abass Department of

More information

COMPLIANCE WITH THIS PUBLICATION IS MANDATORY

COMPLIANCE WITH THIS PUBLICATION IS MANDATORY BY ORDER OF THE COMMANDER 50TH SPACE WING 50TH SPACE WING INSTRUCTION 10-217 17 MAY 2013 Incorporating Cange 4, 8 May 2017 Operations AIR FORCE SATELLITE CONTROL NETWORK (AFSCN) USERS OPERATIONS INSTRUCTIONS

More information

CALCULATION ON DEFORMATION RATIO OF SHEAR TO BENDING FOR

CALCULATION ON DEFORMATION RATIO OF SHEAR TO BENDING FOR CLCULTON ON DEFORMTON RTO OF SHER TO BENDNG FOR STEEL RENFORCED CONCRETE SPECL-SHPED COLUMNS Liu Yi, Xue Jianyang, Zao Hongtie, Cen Zongping 3 Candidate for P.D., Sool of Civil Engineering, Xi an University

More information

Volume 14. No

Volume 14. No Volume 4. No 03 Transporta un sakaru institūts (Transport and Telecommunication Institute) Transport and Telecommunication Volume 4, No - 03 ISSN 407-660 ISSN 407-679 (On-line: www.tsi.lv) Riga 03 05 T8

More information

ME -215 ENGINEERING MATERIALS AND PROCESES

ME -215 ENGINEERING MATERIALS AND PROCESES ME -215 ENGINEERING MATERIALS AND PROCESES Instructor: Office: MEC325, Tel.: 973-642-7455 E-mail: samardzi@njit.edu PROPERTIES OF MATERIALS Chapter 3 Materials Properties STRUCTURE PERFORMANCE PROCESSING

More information

True Stress and True Strain

True Stress and True Strain True Stress and True Strain For engineering stress ( ) and engineering strain ( ), the original (gauge) dimensions of specimen are employed. However, length and cross-sectional area change in plastic region.

More information

Fermentation in 24-well plates is an efficient screening platform for filamentous fungi

Fermentation in 24-well plates is an efficient screening platform for filamentous fungi Letters in Applied Microbiology ISSN -5 ORIGINAL ARTICLE Fermentation in -well plates is an efficient screening platform for filamentous fungi T. Linde, N.B. Hansen,M.L ubeck and P.S. L ubeck Section for

More information

Using NI LabVIEW to automate analyses of water flow to a subsurface drain in a layered soil

Using NI LabVIEW to automate analyses of water flow to a subsurface drain in a layered soil Using NI LabVIEW to autoate analyses of water flow to a subsurface drain in a layered soil CONSTANTIN BUTA*, CARMEN MAFTEI*, CORNEL CIUREA, *COSMIN BUCUR**, LUCIAN BALASA** *Civil Engineering Faculty and,

More information

École doctorale n 364 : Sciences Fondamentales et Appliquées. Doctorat ParisTech T H È S E. pour obtenir le grade de docteur délivré par

École doctorale n 364 : Sciences Fondamentales et Appliquées. Doctorat ParisTech T H È S E. pour obtenir le grade de docteur délivré par N : 2009 ENAM XXXX École doctorale n 364 : Sciences Fondamentales et Appliquées Doctorat ParisTec T H È S E pour obtenir le grade de docteur délivré par l École nationale supérieure des mines de Paris

More information

Mechanical Properties of Materials

Mechanical Properties of Materials INTRODUCTION Mechanical Properties of Materials Many materials, when in service, are subjected to forces or loads, it is necessary to know the characteristics of the material and to design the member from

More information

Shape Memory Alloys: Thermoelastic Martensite

Shape Memory Alloys: Thermoelastic Martensite Shape Memory Alloys: Thermoelastic Martensite MatE 152 Thermoelastic Martensite Shape Memory Alloys (SMA) The strain of transformation is much less than the martensitic transformation in steel Thus product

More information

Groundwater Modeling

Groundwater Modeling Groundwater Modeling -introduction and some applications in Delaware Presented by: Cangming He Delaware Geological Survey Wat is a groundwater flow model? A groundwater flow model is a matematical representation

More information

Operating Reserve Quantification Considering System Uncertainties and Day-ahead Optimal Dispatching of a Microgrid with Active PV Generators

Operating Reserve Quantification Considering System Uncertainties and Day-ahead Optimal Dispatching of a Microgrid with Active PV Generators Réunion du Groupe de travail sur les microréseaux Tuesday, November 15, 216 Operating Reserve Quantification Considering System Uncertainties and Day-aead Optimal Dispatcing of a Microgrid wit Active PV

More information

An intertemporal decision framework for electrochemical energy storage management

An intertemporal decision framework for electrochemical energy storage management SULEMENTARY INFORMATION Article ttp://doi.org/10.1038/41560-018-0129-9 In te format provided by te autor and unedited. An intertemporal deciion framework for electrocemical energy torage management Guannan

More information