Modeling and Simulation of A Laser Deposition Process

Size: px
Start display at page:

Download "Modeling and Simulation of A Laser Deposition Process"

Transcription

1 Modeling and Simulation of A Laer Depoition Proce rank Liou*, Zhiqiang an*, Heng Pan*, Kevin Slattery**, Mary Kinella+, Joeph Newkirk*, and Hin-Nan Chou** *Univerity of Miouri Rolla, Rolla, MO, ** The Boeing Company + ARL/MLLMP Reviewed, accepted September 4, 2007 Abtract A laer depoition proce involve the upply of metallic powder into a laer-heated pot where the powder i melted and form a melt puddle which quickly olidifie into a bead. In order to deign an effective ytem, the laer beam, the powder beam, and their interaction need to be fully undertood. In thi paper, the laer-material interaction within the melt pool i reported uing a multi-cale model: a macrocopic model to model ma, heat, and momentum tranfer. Experiment were alo conducted to validate the imulation model. Introduction The direct laer depoition (DLD) proce i an extenion of the laer cladding proce for rapid prototyping of fully dene metal component. It offer the ability to make a metal component directly from CAD drawing. It involve the upply of metallic powder into a laer-heated pot where the powder i melted and form a melt puddle which quickly olidifie into a bead a hown in igure 1. The thermal behavior of the melt pool in which powder i injected i critical for part quality. Thi paper ue imulation and experiment to invetigate the effect of the proce parameter: laer power, powder ma flow, and canning peed on the melt pool thermal behavior. During the laer depoition proce, everal defect, uch a poroity and crack, hould be paid attention to. Crack initiate corroion fracture and reduce fatigue trength of the depoited part. Crack are caued by the reidual tree created by the high thermal gradient built up during the cooling tage. Reidual tree can be reduced by a reduction of the cooling rate. Thi can be achieved by preheating the ubtrate. Moreover, the preheating caue a better aborption of the laer beam and further it i poible to melt more powder in the larger melting pool and enhance the bonding. Uually the preheating i performed in uch a manner that a very mall melting of the ubtrate material occur without powder injection. Thermal analyi of the laer depoition proce i very important for optimization of the proce. If the ubtrate urface temperature remain too low, wetted depoit material i limited. In that cae, Laer Depoition Nozzle Subtrate Powder eeder Powder delivery tube Melt pool ig 1 Laer-powder interaction at melt pool in a direct laer depoition (DLD) proce. 212

2 irregularly haped track with a lot of crack, poroity and a poor bonding, are produced. However, if an extremely high temperature of the ubtrate urface i reached, evere melting of the ubtrate occur. The high degree of dilution can deteriorate the clad propertie. A comprehenive numerical model ha been developed that allow the prediction of temperature ditribution and melt pool dynamic. Thi model imulate the coaxial laer depoition proce with powder injection, and conider mot of the aociated phenomena, uch a melting, olidification, evaporation, evolution of the free urface, and powder injection. Input parameter for thi model are laer machining parameter and propertie of the laer beam, a well a material propertie and laer beam aborption. To get more accurate prediction, a finer grid need to be ued. Thi, together with the iterative nature of the numerical algorithm, caue the model computationally not to be very efficient. In thi paper an analytical model i applied to the preheating proce (without powder injection) to increae the computational efficiency, while the actual depoition proce with powder injection till ue the numerical model. The output, and the temperature ditribution of the ubtrate, are ued a the initial condition of the numerical model. In thi tudy, a coaxial diode laer depoition ytem, LAMP (developed at UMR), i conidered for imulation and experiment. The blown powder method i ued to deliver powder. A the primary laer in the LAMP ytem, the diode laer i ued. Material of both powder and ubtrate i Ti-6Al-4V, which i widely ued in the aeropace indutry. Melt Pool Governing Equation igure 2 how a chematic diagram of the calculation domain, including the ubtrate, melt pool, remelted zone, depoited layer and part of the ga region. In the laer depoition proce, melting and olidification caue the phae tranformation at the olid/liquid interface. A muhy zone containing olid and liquid i formed. In thi tudy the continuum model [Bennon87a, Bennon87b] i adopted to derive the governing equation. Depoited layer Remelted zone Shielding ga melt pool Subtrate Laer beam Powder ig. 2. Schematic of the calculation domain. The aumption for the ytem of governing equation include: (1) the fluid flow in the melt pool i a Newtonian, incompreible, laminar flow; (2) the olid and liquid phae in the muhy zone are in local thermal equilibrium; (3) the olid phae i rigid; and (4) iotropic permeability exit. or the ytem of interet, the conervation equation for ma, momentum and energy are ummarized a follow: 213

3 Continuity ρ v + ( ρv ) = 0 t (1) Momentum Energy v v v ρ v μl ρ v v v ( ρ V ) + ( ρvv ) = ( μl V ) p ( V V ) + ρg + S (2) t ρ K ρ l l ( ρh) v v v + ( ρvh) = ( k T) ( ρ( hl h)( V V) t (3) In equation (1)-(3), the continuum denity, pecific heat, thermal conductivity, vector velocity, and enthalpy are defined a follow: ρ ρ ρ = g + gl l c fc fc l l v v v V = f V + f V l l = + k = gk + glkl The liquid fraction temperature relationhip i given by: h= fh + flh (4) l 0 if T < T T T gl = if T T Tl Tl T 1 if T > Tl (5) The other volume and ma fraction can be obtained by: f l g ρ ρ l l = f g ρ = g + gl = 1 f = 1 fl (6) ρ The phae enthalpy for the olid and the liquid can be expreed a: h = T 0 c ( T) dt T h= c( TdT ) + ctdt ( ) + L l 0 T l m T (7) where L m i the latent heat of melting. Permeability, K, i aumed to vary with liquid volume fraction according to the Carman - Kozeny equation [Carman37] derived from Darcy law: 214

4 3 K gl = C (1 g ) l 2 (8) where the parameter C i a contant depending on the morphology and ize of the dendrite in the muhy zone. The S i a ource term that i defined below. Solid/liquid interface The olid/liquid interface i implicitly tracked by the continuum model [Bennon87a, Bennon87a]. In the olid phae region and liquid phae region, the third term on the right-hand v v ide of Eq. (2) vanihe. Thi i becaue in the olid phae region V = V = 0 and in liquid phae region K ince g l = 1. So thi term i only valid in the muhy zone. ree urface The liquid/vapor interface, or the free urface of the melt pool, i very complex due to urface tenion, thermocapillary force, and impaction of the powder injection. In thi tudy, the Volume- Of-luid (VO) method [Hirt81] i employed to track the evolution of the moving free urface of the melt pool. The melt pool configuration i defined in term of a volume of fluid function, (x,y,t), which repreent the volume of fluid per unit volume and atifie the conervation equation: t + ( V ) = 0 (9) Source term The ource term, S, in the momentum equation i contributed by the interface force acting on the free urface, uch a urface tenion, etc. In thi tudy, the continuum urface force (CS) model [Brackbill92] i ued to reformulate the urface force. In it tandard form, urface tenion i formulated a [Brackbill92]: r ( x v ) = nˆ γκ + Sγ r where ( x v ) i the net urface force at a point x v on a interface S. ˆn i a unit normal to S at the point x v, which i given by: n r nˆ = r (11) n where n v i the urface normal vector and can be computed from the gradient of the VO function: v n = (12) i the gradient along a direction tangential to the interface, which i defined a: S (10) 215

5 ˆ( ˆ S = N = n n ) (13) γ and κ repreent urface tenion coefficient and curvature, repectively. κ i given in [ Prakah89]: 1 n v v κ = ( nˆ ) = v ( v ) n ( n) n n (14) By uing the CS model, the urface force r i reformulated into a volume force r b a follow: r b r = S r n r = S (15) where i the averaged value acro the free urface. Thu, the ource term S in equation (2) i formulated a: v S = ( nγκ + Sγ ) (16) Boundary Condition The boundary condition at the free urface atify the following equation: T η( Plaer Patten) 4 4 k = h ( ) ( ) 2 c T T εσ T T m& el (17) v n π R where term on the right-hand ide are laer irradiation, convective heat lo, radiation heat lo and evaporation heat lo, repectively. P laer i the power of laer beam, P atten the power attenuated by the powder cloud, R i the laer beam radiu, η the laer aborption coefficient. P atten i calculated according to renk et al. model [renk97] with a minor modification: P atten 3Qextml & = Plaer 1 exp πρr D v p jet p (18) where m& denote the powder ma flow rate, l i the tand-off ditance from the nozzle exit to the ubtrate, ρ i powder denity, r p i the radiu of the powder particle, D jet i the diameter of the powder jet, v p i the powder injection velocity, and Q ext i the extinction coefficient. It i aumed that the extinction cro ection i cloe to the actual geometrical cro ection, and Q ext take a value of unity. In the evaporation term, m& i the evaporation ma flux and L v i the e 216

6 latent heat of evaporation. According to Choi et al. overall evaporation model [Choi87], m& e i of the form: log m& e = A logT (19) T where A i a contant dependent on the material. The boundary condition at the bottom, left and right wall atify the following equation: T k = h ( ) c T T n (20) u = 0 v = 0 (21) Powder injection Powder particle that inject onto the top urface can be claified into three categorie. 1) Thoe powder particle that have not been melted during their paage and hit the olid part of the ubtrate will deflect and loe; 2) Thoe powder particle that have been melted before they arrive on the ubtrate and impact the olid part of the ubtrate will tick to the urface of the ubtrate; and 3) Thoe powder particle that fall into the melt pool including melted and unmelted will merge and mix with the molten liquid in the melt pool [Han04]. In thi tudy, the powder particle belonging to the lat two cae were modeled. Numerical imulation Simulation i performed baed on the capability of the experimental facilitie to compare the imulation reult with the experimental meaurement. A continuou wave diode laer with an 808 nm wavelength i conidered a the energy ource. The laer intenity ditribution i uniform. or ubtrate, Ti-6Al-V4 plate with a thickne of 0.25 inch are elected. Ti-6Al-V4 powder particle with a diameter from 40 to 140 μm are ued a depoit material. The laer aborption coefficient i meaured by Spark et al. [Spark06]. The material propertie and the main proce parameter are hown in Table 1. igure 3 how typical imulation reult for normal depoition and lack of fuion. ig. 3. Typical reult (a) Temperature for imulation field of normal depoition (b) Velocity (left) and field lack of fuion (right). 217

7 Experimental Study The experiment were performed on the LAMP ytem which conit of a diode laer, powder delivery unit, 5-axi CNC machine, and monitoring ubytem. The laer ytem ued in the tudy wa Nuvonyx (Nuvonyx Inc.) ISL-1000M Laer Diode Sytem which combine tate-ofthe-art micro-optic with laer diode to produce the only ingle wavelength fiber coupled direct diode laer at power level up to 1000 watt CW. The laer emit at 808 nm and operate in the continuou wave (CW) mode. The ubtrate have dimenion of in. The Ti-6Al-4V ample were irradiated uing a laer beam with a beam pot diameter of 2.5 mm. Table 1. Material propertie for Ti-6Al-4V and main proce parameter Nonmenclature Symbol Value (unit) Melting temperature T m K Liquidu temperature T l K Solidu temperature T K Evaporation temperature T v K Solid pecific heat at contant c p T T 1268K preure [Kelly04] T 1268 < T 1923 J / kg K Liquid pecific heat at contant preure [Mill02] Thermal conductivity [ Kelly04] c pl J/kg K k T T 1268K T 1268 < T 1923 W / m K T T > 1923 Solid denity [Mill0] ρ (T 298 K) Liquid denity [Mill0] ρ l (T 1923 K) Latent heat of fuion [Mill0] L m J/kg Latent heat of evaporation L v J/kg Dynamic vicoity μ N/m (1923K) (1973K) (2073K) (2173K) Radiation emiivity [Lip 05] ε (T K) Laer aborption coefficient [ Spark04] Powder particle diameter D p μm Shielding ga preure P g 5 pi Ambient temperature T 300K Convective coefficient h c 10 W/m 2 K η 0.4 In order to validate the model prediction, ingle path depoition experiment are conducted. The comparion between model prediction and experimental reult are conducted in term of melt pool peak temperature. The melt pool peak temperature i calibrated through the dualwavelength non-contact temperature enor, which can effectively decreae the diturbance from the powder and other dut. Comparion and dicuion ig. 4 and ig. 5 how the comparion between experimental meaurement and model prediction. ig. 4 how the effect of laer power on melt pool peak temperature. It can be een that an increae in the laer power will increae the melt pool temperature. Thi i eay to 218

8 undertand. A the laer power increae, more power i available for melting the ubtrate. ig. 5 how the effect of laer canning peed on the melt pool peak temperature. An increae in the laer canning peed will decreae the melt pool peak temperature. Thi i becaue, a canning peed decreae, the laer material interaction time i extended. rom ig. 4-5, one can ee that the general trend between experimental meaurement and model prediction i conitent. At a different power intenity level, there i a different error from 10 K (about 0.5%) to 121K (about 5%). It can be een that at a higher power intenity level, there i a bigger error between meaurement and prediction. Thi i becaue the numerical model i two-dimenional. It doe not conider the heat and ma tranfer in the third direction. At a higher power intenity level, heat and ma tranfer in the third dimenion are more ignificant. The error between experimental meaurement and model prediction are analyzed to mainly come from the following apect: (1) The two-dimenional nature of the numerical model; (2) The thermo-phyical propertie taken for the analytical model; (3) The uncertaintie of the material propertie and the appropriatene of the ub-model for the numerical model; (4) Boundary condition. Adiabatic boundary condition are aumed in the analytical model and the numerical model for the bottom urface and ide urface. Meaurement alo have been taken to achieve uch boundary condition in experiment. But it i hard to get abolute adiabatic boundary condition Melt Pool Peak Temperature, K Experimental reult Model prediction Laer Power, W ig. 4 Comparion between experimental meaurement and model prediction at a contant powder ma flow rate of 5g/min and a contant laer canning peed of 20 inch/min. (or actual depoition) 219

9 Melt Pool Peak Temperature, K Experimental reult Model prediction Laer Scanning Speed, inch/min. ig. 5 Comparion between experimental meaurement and model prediction at a contant powder ma flow rate of 5g/min and a contant laer power of 700 W. (or actual depoition) The imulation model wa alo ued to predict the lack of fuion to depoit Ti64. Twenty-eight Ti64 ample were built to validate the imulation model. The idea wa to ue the imulation model to predict the lack of fuion, and the correponding laer power i ued a nominal power. The depoition are then baed on Nominal, Nominal +- 10%, Nominal +- 20%, and Nominal +- 30%. The nominal i about 600 W for the direct diode laer. The nominal power i then et at 600W with a travel peed (canning peed) at 10ipm and powder flow rate ~ 5g/min. The experiment wa performed at -30% (420W), -20% (480W), -10% (540W), nominal (600W), 10%(660W), 20%(720W), 30% (780W). If the predicted model for lack of fuion i accurate, about 50% of the part will be oberved a lack of fuion. Seven ample of thick wall are hown in igure 6. It can be oberved that mot ample with lower power than the nominal howed obviou poroitie on the ample urface. (a) Sample produced at -30% laer power (b) Sample produced at -20% laer power 220

10 (c) Sample produced at -10% laer power (d) Sample produced at nominal laer power (e) Sample produced at +10% laer power (f) Sample produced at +20% laer power (g) Sample produced at +30% laer power ig 6. A thick wall Ti64 part produced at variou laer power (Nominal, Nominal +- 10%, Nominal +- 20%, and Nominal +- 30%) in the UMR LAMP lab. Lack of fuion can be oberved from ome urface of the ample with lower power. Concluion The thermal behavior of melt pool i the mot critical phenomenon in laer depoition. An analytical model for thermal analyi of temperature rie due to a moving heat ource i combined into a comprehenive heat tranfer and fluid flow numerical model for the laer depoition proce. The analytical model i ued for the preheating proce before the actual 221

11 laer depoition with powder injection. And the numerical model i ued for the actual laer depoition proce. Thu the output of the analytical model are ued a the input of the numerical model. Experiment have been conducted to validate the model prediction. A conitent general trend i found between experimental meaurement and the model prediction. The ource of the error have alo been analyzed. Acknowledgement Thi reearch wa upported by the National Science oundation Grant Number DMI , the grant from the U.S. Air orce Reearch Laboratory contract # A C-5704, and UMR Intelligent Sytem Center. Their upport i greatly appreciated. Reference Bennon, W.D.,.P. Incropera, A continuum model for momentum, heat and pecie tranport in binary olid-liquid phae change ytem-i. Model formulation, International Journal of Heat and Ma Tranfer 30 (1987a) Bennon, W.D.,.P. Incropera, A continuum model for momentum, heat and pecie tranport in binary olid-liquid phae-change ytem--ii. Application to olidification in a rectangular cavity, International Journal of Heat and Ma Tranfer 30 (1987b) Brackbill, J. U., D. B. Kothe, C. Zemach, A continuum method for modeling urface tenion, Journal of Computational Phyic 100 (1992) Carman, P.C., luid flow through granular bed, Tran. Intitution Chem. Engr. 15 (1937) Choi, M., R. Greif, M. Salcudean, A tudy of the heat tranfer during arc welding with application to pure metal or alloy and low or high boiling temperature material, Numerical Heat Tranfer 11 (1987) renk, A., M. Vandyouefi, J. Wagniere, A. Zryd, W. Kurz, Analyi of the laer-cladding proce for tellite on teel, Metallurgical and Material Tranaction B (USA) 28B (1997) Han, L.,.W. Liou, K.M. Phatk, Modeling of laer cladding with powder injection, Metallurgical and Material Tranaction B 35B (2004) Hirt, C.W., B.D. Nichol, Volume of fluid (VO) method for the dynamic of free boundarie, Journal of Computational Phyic 39 (1981)

12 Kelly, S.M., Thermal and microtructure modeling of metal depoition procee with application to Ti-6Al-4V, Ph.D. thei, Virginia Polytechnic Intitute and State Univerity, Mill, K. C., Recommended value of thermophyical propertie for elected commercial alloy, Woodhead, Cambridge, Lip, Tobia, Bent ritche, A comparion of commonly ued re-entry analyi tool, Acta Atronautica 57 (2005) Prakah, C., V. Voller, On the numerical olution of continuum mixture model equation decribing binary olid-liquid phae change, Numerical Heat Tranfer 15B (1989) Spark, Todd E., Zhiqiang an, Meaurement of laer aborption coefficient of everal alloy for diode laer, unpublihed report,

Modeling Liquid Phase Sintering of Hard metal powder compacts

Modeling Liquid Phase Sintering of Hard metal powder compacts ing Liquid Phae Sintering of Hard metal powder compact Shama Shamaundar *, Maheha Siddegowda*, Pavanachand Chigurupati**, Rengarajan Raghavan***, Rameh Rao. S. *** * ProSIM AFTC # 326, 8th Main, III Stage,

More information

3.4 BUTT FUSION WELDING

3.4 BUTT FUSION WELDING 3.4 BUTT FUSION 3.4.1 INTRODUCTION The butt welding proce conit of the joining of two component (pipe and/or fitting) of equal diameter and thickne in which the urface to be welded are heated until melting

More information

Equilibrium Sediment Transport and Evolution Trend Simulation of the Lower Yellow River

Equilibrium Sediment Transport and Evolution Trend Simulation of the Lower Yellow River Senor & Tranducer, Vol. 21, Special Iue, May 213, pp. 135-141 Senor & Tranducer 213 by IFSA http://www.enorportal.com Equilibrium Sediment Tranport and Evolution Trend Simulation of the Lower Yellow River

More information

The Use of Swimmer Bars as Shear Reinforcement in Reinforced Concrete Beam

The Use of Swimmer Bars as Shear Reinforcement in Reinforced Concrete Beam American Journal of Engineering and Applied Science, 6 (1): 87-94, 2013 ISSN: 1941-7020 2014 M. Al-Nara et al., Thi open acce article i ditributed under a Creative Common Attribution (CC-BY) 3.0 licene

More information

Land-Surface Models, Page 1

Land-Surface Models, Page 1 Land-Surface Model Introduction A land-urface model mut be able to accurately depict the interaction of the atmophere with the underlying urface land a well a the interaction of the ub-urface, or ubtrate,

More information

Keywords: ILSS, Flexural Strength, Hybrid Polymer Composite, Curing, Epoxy Resin 5052, Vacuum Bagging.

Keywords: ILSS, Flexural Strength, Hybrid Polymer Composite, Curing, Epoxy Resin 5052, Vacuum Bagging. American International Journal Reearch in Science, Technology, Engineering & Mathematic Available online at http://www.iair.net ISSN (Print): 2328-3491, ISSN (Online): 2328-3580, ISSN (CD-ROM): 2328-3629

More information

Exergy Analysis of Organic Rankine Cycle with Internal Heat Exchanger

Exergy Analysis of Organic Rankine Cycle with Internal Heat Exchanger International Journal of Material, Mechanic and Manufacturing, Vol. 1, No. 1, February 21 Exergy Analyi of Organic Rankine Cycle with Internal Heat Exchanger Kyoung Hoon Kim, Hyung Jong Ko, and Se Woong

More information

A Morphing Extrusion Die for Manufacturing of Thermoplastic Hoses THESIS

A Morphing Extrusion Die for Manufacturing of Thermoplastic Hoses THESIS A Morphing Extruion Die for Manufacturing of Thermoplatic Hoe THESIS Preented in Partial Fulfillment of the Requirement for the Degree Mater of Science in the raduate School of The Ohio State Univerity

More information

Challenges of Developing ISO Sampling Standards

Challenges of Developing ISO Sampling Standards Challenge of Developing ISO Sampling Standard Ralph Holme CSIRO Mineral Down Under Flaghip Chair ISO/TC 10/SC 1 Sampling Iron Ore Chair ISO/TC 7/SC 4 Sampling Coal and Coke Convenor ISO/TC 183/WG 9 Sampling

More information

M A S O N R Y. Revised Spring Engineering Notes For Design With Concrete Block Masonry

M A S O N R Y. Revised Spring Engineering Notes For Design With Concrete Block Masonry A S O N R Y Revied Spring 007 Engineering Note For Deign With Concrete Block aonry C H R O N I C L E S To rectify the ituation, the Spring 007 article i being reiued. We apologize for any inconvenience

More information

Bachelor End Project: Characterization of the constitutive behavior of polymer foams

Bachelor End Project: Characterization of the constitutive behavior of polymer foams Bachelor End Project: Characterization of the contitutive behavior of polymer foam R. van Eijden MT 05.27 Coach: Dr. ir. J.A.W. van Dommelen Eindhoven, April 21t 2005 Content Content Abtract Lit of ymbol

More information

Dynamic compressive and splitting tensile tests on mortar using split Hopkinson pressure bar technique

Dynamic compressive and splitting tensile tests on mortar using split Hopkinson pressure bar technique 730 Dynamic compreive and plitting tenile tet on mortar uing plit Hopkinon preure bar technique Abtract Dynamic compreive and tenile propertie of mortar under impact loading were invetigated experimentally

More information

BELIEF PROPAGATION REVEALS ALLOSTERIC MECHANISMS IN PROTEINS

BELIEF PROPAGATION REVEALS ALLOSTERIC MECHANISMS IN PROTEINS BELIEF PROPAGATION REVEALS ALLOSTERIC MECHANISMS IN PROTEINS Hetunandan Kamietty Computer Science Department, Carnegie Mellon Univerity, Pittburgh, PA 15213, USA Email: hetu@c.cmu.edu Arvind Ramanathan

More information

de l Université de recherche Paris Sciences et Lettres PSL Research University

de l Université de recherche Paris Sciences et Lettres PSL Research University THÈSE DE DOCTORAT de l Univerité de recherche Pari Science et Lettre PSL Reearch Univerity Préparée à MINES PariTech Deformation of teel ingot by punch preing during their olidification. Numerical modelling

More information

Effect of Cobalt Doping on Physical Properties of ZnO Nanoparticles

Effect of Cobalt Doping on Physical Properties of ZnO Nanoparticles CPUH-Reearch Journal: 06, (), 47-5 ISSN (nline): 455-6076 http://www.cpuh.in/academic/academic_journal.php Effect of Cobalt oping on Phyical Propertie of Zn Nanoparticle Neha Sharma, Shaveta Thakur, Ruchita

More information

Typical Albedo ALBEDO 1/14/13. Albedo. Disposition of Solar Radiation at Earth s Surface

Typical Albedo ALBEDO 1/14/13. Albedo. Disposition of Solar Radiation at Earth s Surface Introduction to Climatology GEOGAPHY 300 Dipoition of Solar adiation at Earth Surface Tom Giambelluca Univerity of Hawai i at Mānoa eflection: Albedo i a key property of urface controlling the urface energy

More information

Enhanced Biofilter Treatment of Urban Stormwater by Optimizing the Hydraulic Residence Time in the Media

Enhanced Biofilter Treatment of Urban Stormwater by Optimizing the Hydraulic Residence Time in the Media Enhanced Biofilter Treatment of Urban Stormwater by Optimizing the Hydraulic Reidence Time in the Media Redahegn Silehi 1, Robert Pitt 2 and Shirley Clark 3 1 Graduate tudent, Dept. of Civil, Contruction,

More information

Simulation of Continuous Bio-Reactor

Simulation of Continuous Bio-Reactor Proceeding of he 5 th nnual International Conference Syiah Kuala Univerity (IC Unyiah) 205 In conjunction with he 8 th International Conference of Chemical Engineering on Science and pplication (ChES)

More information

The University of Bradford Institutional Repository

The University of Bradford Institutional Repository he Univerity of Bradford Intitutional Repoitory http://bradcholar.brad.ac.uk hi work i made available online in accordance with publiher policie. Pleae refer to the repoitory record for thi item and our

More information

Analysis of Disk AC MHD Generator Performance by Finite Element Method

Analysis of Disk AC MHD Generator Performance by Finite Element Method J. Plaa Fuion Re. SERIES, Vol. 9 () Analyi o Dik AC MHD Generator Perorance by Finite Eleent Method Pattana INTANI, Toru SASAKI, Takahi KIKCHI and Nob.HARADA Departent o Electrical Engineering, Nagaoka

More information

Habitat Evaluation Procedures. Habitat Evaluation Procedures. Habitat Evaluation Procedures. Habitat Evaluation Procedures

Habitat Evaluation Procedures. Habitat Evaluation Procedures. Habitat Evaluation Procedures. Habitat Evaluation Procedures 969-976 an enlightened Congre pae conervation legilation Affecting management of fih & ldlife reource NEPA (National Environmental Policy Act ESA Foret & Rangeland Renewable Reource Planning Act Federal

More information

Modeling and Simulation of Biological Anaerobic Treatment of Sludge Resulted from Wastewater Treatment

Modeling and Simulation of Biological Anaerobic Treatment of Sludge Resulted from Wastewater Treatment Modeling and imulation of Biological Anaerobic Treatment of ludge Reulted from Watewater Treatment AUREL PREURĂ, LĂCRĂMIOARA DIANA ROBECU 2, ILEANA IRINA PANAITECU 3.C. RAJA Contanța.A. 22-24 Călărași

More information

GMACE Pilot #4: Adjusting the National Reliability Input Data

GMACE Pilot #4: Adjusting the National Reliability Input Data INTERBULL BULLETIN NO. 48. Berlin, Germany, May 20 21, 2014 GMACE Pilot #4: Adjuting the National Reliability Input Data P. G. Sullivan 1 and J. H. Jakoben 2 1 Canadian Dairy Network, Guelph, ON, Canada

More information

Carrier-Gas Enhanced Atmospheric Pressure Desalination (Dewvaporation): Economic Analysis and Comparison to Reverse Osmosis and Thermal Evaporation

Carrier-Gas Enhanced Atmospheric Pressure Desalination (Dewvaporation): Economic Analysis and Comparison to Reverse Osmosis and Thermal Evaporation Carrier-Ga Enhanced Atmopheric Preure Dealination (Dewvaporation): Economic Analyi and Comparion to Revere Omoi and Thermal Evaporation Noah Abba and Kehinde Adeoye Chemical Engineering Undergraduate Univerity

More information

THE POTENTIAL AND COST OF CARBON SEQUESTRATION IN AGRICULTURAL SOIL; EMPIRICAL STUDY OF DYNAMIC MODEL IN THE MIDWESTERN U.S.

THE POTENTIAL AND COST OF CARBON SEQUESTRATION IN AGRICULTURAL SOIL; EMPIRICAL STUDY OF DYNAMIC MODEL IN THE MIDWESTERN U.S. THE POTENTIAL AND COST OF CARBON SEQUESTRATION IN AGRICULTURAL SOIL; EMPIRICAL STUDY OF DYNAMIC MODEL IN THE MIDWESTERN U.S. DISSERTATION Preented in Partial Fulfillment of the Requirement for the Degree

More information

Abstract. Nomenclature. A Porosity function for momentum equations L Latent heat of melting (J/Kg) c Specific heat (J/kg-K) s Liquid fraction

Abstract. Nomenclature. A Porosity function for momentum equations L Latent heat of melting (J/Kg) c Specific heat (J/kg-K) s Liquid fraction Enthalpy Porosity Method for CFD Simulation of Natural Convection Phenomenon for Phase Change Problems in the Molten Pool and its Importance during Melting of Solids Abstract Priyanshu Goyal, Anu Dutta,

More information

Application of the standard porosimetry method for nanomaterials. Y.M. Volfkovich and A.V. Sakars*

Application of the standard porosimetry method for nanomaterials. Y.M. Volfkovich and A.V. Sakars* 292 Int. J. Nanotechnology, Vol. 2, No. 3, 2005 Application of the tandard poroimetry method for nanomaterial Y.M. Volfkovich and A.V. Sakar* Porotech Ltd., 100 Cater Avenue, Vaughan, L4L 5Y9 Ontario,

More information

Y. T. Puyate* and Z. R. Yelebe**

Y. T. Puyate* and Z. R. Yelebe** Y. T. Puyate, Z. R. Yelebe / International Journal of Engineering Reearch and Application (IJERA) ISSN: 48-96 www.ijera.com Vol., Iue 6, November- December 1, pp.93-911 Etimation Of Monod Kinetic Parameter

More information

Gas Processing Expander

Gas Processing Expander Expander Operated Ga Proceing April, 2015 Ga Proceing Expander Colder Proce Temperature and Maximized Compreor Uptime with Helidyne Expander Skid. Specification: Flowrate 1-10 mmcfd Max. Preure 1,440 pi

More information

Management Science Letters

Management Science Letters Management Science Letter 2 (202) 247 252 Content lit available at GrowingScience Management Science Letter homepage: www.growingscience.com/ml An empirical tudy to meaure the impact of loan aignment for

More information

2D axial-symmetric model for fluid flow and heat transfer in the melting and resolidification of a vertical cylinder

2D axial-symmetric model for fluid flow and heat transfer in the melting and resolidification of a vertical cylinder Presented at the COMSOL Conference 2010 Paris 2D axial-symmetric model for fluid flow and heat transfer in the melting and resolidification of a vertical cylinder Simon Morville, Muriel Carin, Denis Carron,

More information

Establishment and evaluation of operation function model for cascade hydropower station

Establishment and evaluation of operation function model for cascade hydropower station Water Science and Engineering, 2010, 3(4):443-453 doi:10.3882/j.in.1674-2370.2010.04.007 http://www.waterjournal.cn e-mail: we2008@vip.163.com Etablihment and evaluation o operation unction model or cacade

More information

Pollution prevention with chemical process simulators: the generalized waste reduction (WAR) algorithm full version

Pollution prevention with chemical process simulators: the generalized waste reduction (WAR) algorithm full version Computer and Chemical Engineering 23 (1999) 623 634 Pollution prevention with chemical proce imulator: the generalized wate reduction (WAR) algorithm full verion Heriberto Cabeza *, Jane C. Bare, Subir

More information

Model of Integrated Production and Delivery Batch Scheduling Under JIT Environment to Minimize Inventory Cost

Model of Integrated Production and Delivery Batch Scheduling Under JIT Environment to Minimize Inventory Cost Proceeding of the 2014 International Conference on Indutrial Engineering and Operation Management Bali, Indoneia, January 7 9, 2014 Model of Integrated Production and Delivery Batch Scheduling Under JIT

More information

Address for Correspondence

Address for Correspondence Reearch Paper ENERGY CONSERVATION IN MUD HOUSE AS COMPARED TO BRICK WALL BUILDING IN INDIA Subhah Mihra 1, Dr. J A Umani 2 Addre for Correpondence 1 Ph.d Scholar, 2 Profeor, Department of Mechanical Engineering,

More information

TD 1 BASIC CONCEPTS AND ENERGY ANALYSIS

TD 1 BASIC CONCEPTS AND ENERGY ANALYSIS TD 1 BASIC CONCEPTS AND ENERGY ANALYSIS TD 1.1 Denity of liquid water i r = _ 1008 - T 2 i / m with T in c C. If the temperature increae 10c C, how much will be the change in per meter depth of water?

More information

AGRON 183: Photosynthesis

AGRON 183: Photosynthesis AGRON 183: Photoynthei Dr. Brian Hornbuckle December 1, 2016 Introduction I think I can afely ay that every agronomit i aware of the proce of photoynthei, a decribed by the following chemical equation.

More information

Study on Variable Action Value Standard for Harbor Infrastructures

Study on Variable Action Value Standard for Harbor Infrastructures 4 th International Conference on the Durability of Concrete Structure 24 26 July 2014 Purdue Univerity, Wet Lafayette, IN, USA Study on Variable Action Value Standard for Harbor Infratructure Xiaoping

More information

Design a Sustainable Supply Chain under Uncertainty using Life Cycle Optimisation and Stochastic Programming

Design a Sustainable Supply Chain under Uncertainty using Life Cycle Optimisation and Stochastic Programming 151 A publication of CHEMICAL ENGINEERING TRANSACTIONS VOL. 61, 2017 Guet Editor: Petar S Varbanov, Rongxin Su, Hon Loong Lam, Xia Liu, Jiří J Klemeš Copyright 2017, AIDIC Servizi S.r.l. ISBN 978-88-95608-51-8;

More information

Cerámica y Vidrio A R T I C U L O

Cerámica y Vidrio A R T I C U L O B O L E T I N D E L A S O C I E D A D E S P A Ñ O L A D E Cerámica y Vidrio A R T I C U L O A view on organic binder effect on technical propertie of ceramic Rachig ring Y. BEYGI KHOSROWSHAHI, A. SALEM

More information

Reservoir simulation and geomechanical modeling in Leming Lake, Alberta

Reservoir simulation and geomechanical modeling in Leming Lake, Alberta Reervoir imulation Reervoir imulation and geomechanical modeling in Leming Lake, Alberta John J. Zhang, Tony Settari and Laurence R. Bentley ABSTRACT Thi paper deal with reervoir imulation and geomechanical

More information

SIMULATION OF THE GAIN CHARACTERISTICS OF EDFA

SIMULATION OF THE GAIN CHARACTERISTICS OF EDFA SIMUTIO OF THE GI CHRCTERISTICS OF EDF guyen Hong Suong and Pham Quoc Ho Deartment of Telecommunication, Pot and Telecommunication Intitute of Technology (PTIT), Ho Chi Mh City, Vietnam BSTRCT In thi tudy,

More information

Application Of Single Blow Technique For Heat Transfer Measurement In Packed Bed Of Vegetables

Application Of Single Blow Technique For Heat Transfer Measurement In Packed Bed Of Vegetables Purdue Univerity Purdue e-pub International Rerigeration and Air Conditioning Conerence School o Mechanical Engineering 2016 Application O Single Blow Technique For Heat Traner Meaurement In Packed Bed

More information

Concentration profiles of gold inside activated carbon during adsorption

Concentration profiles of gold inside activated carbon during adsorption Concentration profile of gold inide activated carbon during adorption by N.M. Vegter*, R.F. Sandenbergh*, and A.J. Botha Synopi The gold concentration profile which develop inide the activated carbon particle

More information

An intertemporal decision framework for electrochemical energy storage management

An intertemporal decision framework for electrochemical energy storage management SULEMENTARY INFORMATION Article ttp://doi.org/10.1038/41560-018-0129-9 In te format provided by te autor and unedited. An intertemporal deciion framework for electrocemical energy torage management Guannan

More information

Abstract. 1 Introduction

Abstract. 1 Introduction Automatic conflict detection and reolution in metrorail ytem: evaluation approach for MARCO EU project G.F. D'Addio, M. Mazzucchelli, S. Savio Dipartimento di Ingegneria Elettrica, Univerita di Genova,

More information

Concept of Heat Recovery from Exhaust Gases

Concept of Heat Recovery from Exhaust Gases IOP Conference Serie: Material Science and Engineering PAPER OPEN ACCESS Concept of Heat Recovery from Exhaut Gae To cite thi article: Maria Bukowka et al 2017 IOP Conf. Ser.: Mater. Sci. Eng. 245 052057

More information

The Arcor/Bagley Merger and the Argentine Biscuit Market: Price Increases vs. Cost Reductions

The Arcor/Bagley Merger and the Argentine Biscuit Market: Price Increases vs. Cost Reductions The rcor/agley Merger and the rgentine icuit Market: rice Increae v. Cot Reduction Germán Coloma* Thi paper analyze the behavior of the rgentine bicuit market during 2003-06 to find out whether any important

More information

4 Farmer Perceptions of the Biophysical

4 Farmer Perceptions of the Biophysical 4 Farmer Perception of the Biophyical Contraint to Rice Production in Sub-Saharan Africa, and Potential Impact of Reearch Aliou Diagne,* Didier Y. Alia, Eyram Amovin-Aagba, Marco C.S. Woperei, Kazuki Saito

More information

Fuel-Powered Compact SMA Actuator

Fuel-Powered Compact SMA Actuator Fuel-Powered Compact SMA Actuator Othon K. Redinioti a, Dimitri C. Lagouda a, Hyoung Y. Jun a, Richard D. Allen a Aeropace Engineering Department Texa A&M Univerity, College Station, TX 77843-3141 ABSTRACT

More information

Tom-Reiel Heggedal and Karl Jacobsen

Tom-Reiel Heggedal and Karl Jacobsen Dicuion Paper No. 536, April 2008 Statitic Norway, Reearch Department Tom-Reiel eggedal and Karl Jacoben Timing of innovation policie when carbon emiion are retricted: an applied general equilibrium analyi

More information

Soil Mechanics & Foundation Engineering

Soil Mechanics & Foundation Engineering SAMPLE STUDY MATERIAL Potal Correpondence Coure GATE, IES & PSU Civil Engineering Soil Mechanic & Foundation Engineering 28-B/7, Jia Sarai, Near IIT, Hauz Kha, Ne Delhi-110016. Ph. 011-26514888..engineerintitute.com

More information

SINCE the 1960s, conceptual models are in use to facilitate

SINCE the 1960s, conceptual models are in use to facilitate IEEE TRNSTIONS ON SYSTEMS, MN, ND YBERNETIS PRT Study into the Factor that Influence the Undertandability of Buine Proce Model Hajo. Reijer and Jan Mendling btract Buine proce model are key artifact in

More information

OPTIMIZATION OF ALUMINIUM BLANK SAND CASTING PROCESS BY USING TAGUCHI S ROBUST DESIGN METHOD

OPTIMIZATION OF ALUMINIUM BLANK SAND CASTING PROCESS BY USING TAGUCHI S ROBUST DESIGN METHOD International Journal for Quality reearch UDK 669.76 Original Scientific Paper (.0) OPTIMIZATION OF ALUMINIUM BLANK SAND CASTING PROCESS BY USING TAGUCHI S ROBUST DESIGN METHOD Mekonnen Liben Nekere )

More information

Liquid-Solid Phase Change Modeling Using Fluent. Anirudh and Joseph Lam 2002 Fluent Users Group Meeting

Liquid-Solid Phase Change Modeling Using Fluent. Anirudh and Joseph Lam 2002 Fluent Users Group Meeting Liquid-Solid Phase Change Modeling Using Fluent Anirudh and Joseph Lam 2002 Fluent Users Group Meeting Solidification Model FLUENT can be used to solve fluid flow problems involving both solidification

More information

Software Reverse Engineering Tool for Object Oriented Programming

Software Reverse Engineering Tool for Object Oriented Programming Software Revere Engineering Tool for Object Oriented Programming D.M.Thakore Department of Computer Engineering Bharati vidyapeeth Deemed Univerity College of Engineering, Pune-43, Maharahtra, India S.J.Sarde

More information

Scaling of supersaturation by a simple test

Scaling of supersaturation by a simple test Permafrot, Phillip, pringman & Arenon (ed) 2003 et & Zeitlinger, Lie, IBN 90 5809 582 7 caling of uperaturation by a imple tet M. Dyli oil Mechanic Laboratory of the i Federal Intitute of Technology, Lauanne,

More information

FIRE RESISTANCE RATINGS OF CONCRETE MASONRY ASSEMBLIES. TEK 7-1C Fire Resistance (2009) Related TEK: 2-6, 5-8B, 7-6A

FIRE RESISTANCE RATINGS OF CONCRETE MASONRY ASSEMBLIES. TEK 7-1C Fire Resistance (2009) Related TEK: 2-6, 5-8B, 7-6A n information erie from the national authority on concrete maonry technology FIRE RESISTNCE RTINGS OF CONCRETE MSONRY SSEMBLIES TEK 7-C Fire Reitance (009) INTRODUCTION Concrete maonry i widely pecifi

More information

Narrow Gap Welding, Electrogas - and. Electroslag Welding

Narrow Gap Welding, Electrogas - and. Electroslag Welding 6. Narrow Gap Welding, Electroga - and Electrolag Welding 00 6. Narrow Gap Welding, Electroga- and Electrolag Welding 7 Up to thi day, there i no univeral agreement about the definition of the term Narrow

More information

Further development of indicators in the performance measurement frameworks

Further development of indicators in the performance measurement frameworks Meeting of the Board 8 10 March 2016 Songdo, Incheon, Republic of Korea Proviional agenda item 20 GCF/B.12/13 1March 2016 Further development of indicator in the performance meaurement framework Summary

More information

Online Music Ranking Service: Ranking Mechanism Based on Popularity and Slot Effect

Online Music Ranking Service: Ranking Mechanism Based on Popularity and Slot Effect Aociation for Information Sytem AIS Electronic Library (AISeL) PACIS 00 Proceeding Pacific Aia Conference on Information Sytem (PACIS) 00 Online Muic Ranking Service: Ranking Mechanim Baed on Popularity

More information

FEASIBILITY OF BUILDING AN OVERHANG STRUCTURE USING DIRECT METAL DEPOSITION

FEASIBILITY OF BUILDING AN OVERHANG STRUCTURE USING DIRECT METAL DEPOSITION Proceedings of the 5th Annual ISC Research Symposium ISCRS 2011 April 7, 2011, Rolla, Missouri FEASIBILITY OF BUILDING AN OVERHANG STRUCTURE USING DIRECT METAL DEPOSITION Sriram Prabhu Department Of Manufacturing

More information

CFD MODELLING OF MACRO-SEGREGATION AND SHRINKAGE IN LARGE DIAMETER STEEL ROLL CASTINGS: A COMPARISON ON SEN AND DLP TECHNIQUES

CFD MODELLING OF MACRO-SEGREGATION AND SHRINKAGE IN LARGE DIAMETER STEEL ROLL CASTINGS: A COMPARISON ON SEN AND DLP TECHNIQUES Ninth International Conference on CFD in the Minerals and Process Industries CSIRO, Melbourne, Australia 10-12 December 2012 CFD MODELLING OF MACRO-SEGREGATION AND SHRINKAGE IN LARGE DIAMETER STEEL ROLL

More information

Biological sulphate reduction with primary sewage sludge in an upflow anaerobic sludge bed reactor Part 5: Steady-state model

Biological sulphate reduction with primary sewage sludge in an upflow anaerobic sludge bed reactor Part 5: Steady-state model Biological ulphate reduction with primary ewage ludge in an upflow anaerobic ludge bed reactor Part 5: Steadytate model J Poinapen and GA Ekama 1 Water Reearch Group, Department of Civil Engineering, Univerity

More information

Numerical simulation of heat transfer and fluid flow in coaxial laser cladding process for direct metal deposition

Numerical simulation of heat transfer and fluid flow in coaxial laser cladding process for direct metal deposition JOURNAL OF APPLIED PHYSICS 100, 024903 2006 Numerical simulation of heat transfer and fluid flow in coaxial laser cladding process for direct metal deposition Huan Qi a and Jyotirmoy Mazumder Center for

More information

DESIGN OF SMALL GEOTHERMAL HEATING SYSTEMS AND POWER GENERATORS FOR RURAL CONSUMERS IN MONGOLIA

DESIGN OF SMALL GEOTHERMAL HEATING SYSTEMS AND POWER GENERATORS FOR RURAL CONSUMERS IN MONGOLIA GEOHERMAL RAINING PROGRAMME Report 21 Orkutofnun, Grenávegur 9, Number 3 IS-18 Reykjavík, Iceland DESIGN OF SMALL GEOHERMAL HEAING SYSEMS AND POWER GENERAORS FOR RURAL CONSUMERS IN MONGOLIA Purevuren Dorj

More information

Research Article. Hydration process study on the alkali-activated slag cementing materials

Research Article. Hydration process study on the alkali-activated slag cementing materials Available online wwwjocprcom Journal of Chemical and Pharmaceutical Reearch,, ():88 Reearch Article ISSN : 975738 CODEN(USA) : JCPRC5 Hydration proce tudy on the alkaliactivated lag cementing material

More information

MODELLING OF MICROSTRUCTURE EVOLUTION IN HOT WORK TOOL STEELS DURING SERVICE

MODELLING OF MICROSTRUCTURE EVOLUTION IN HOT WORK TOOL STEELS DURING SERVICE Informatyka w Technologii Materiaów Publihing Houe AKAPIT Vol. 9, 2009, No. 2 MODELLING OF MICROSTRUCTURE EVOLUTION IN HOT WORK TOOL STEELS DURING SERVICE FRIEDRICH KRUMPHALS 1, THOMAS WLANIS 1, CHRISTOF

More information

ENVE 301 Environmental Engineering Unit Operations. CHAPTER: 5 Aeration

ENVE 301 Environmental Engineering Unit Operations. CHAPTER: 5 Aeration ENVE 301 Environmental Engineering Unit Operation CHAPTER: 5 Aeration Ait. Prof. Bilge Alpalan Kocamemi Marmara Univerity Department of Environmental Engineering Itanbul, Turkey 1 Aeration Primary application

More information

Adaptive Description of ATM Traffic Flows 1

Adaptive Description of ATM Traffic Flows 1 Adaptive Decription of ATM Traffic Flow 1 Juergen Rochol Mouriac Halen Diemer (juergen@inf.ufrg.br) (mouriac@univate.br) Univeridade Federal do Rio Grande do Sul - UFRGS Intituto de Informática - Departamento

More information

WHICH CAME FIRST, LAWS OR LOBBYISTS? AN EMPIRICAL INVESTIGATION OF ENVIRONMENTAL REGULATION AND INTEREST GROUP FORMATION. Bryan James Leonard

WHICH CAME FIRST, LAWS OR LOBBYISTS? AN EMPIRICAL INVESTIGATION OF ENVIRONMENTAL REGULATION AND INTEREST GROUP FORMATION. Bryan James Leonard WHICH CAME FIRST, LAWS OR LOBBYISTS? AN EMPIRICAL INVESTIGATION OF ENVIRONMENTAL REGULATION AND INTEREST GROUP FORMATION. by Bryan Jame Leonard A thei ubmitted in partial fulfillment of the requirement

More information

As companies outsource more product design and manufacturing activities to other members of the supply

As companies outsource more product design and manufacturing activities to other members of the supply MANAGEMEN SCIENCE Vol. 55, No. 7, July 2009, pp. 1122 1138 in 0025-1909 ein 1526-5501 09 5507 1122 inform doi 10.1287/mnc.1090.1008 2009 INFORMS Quality Improvement Incentive and Product Recall Cot Sharing

More information

Solubility of Carbohydrates in Subcritical Water

Solubility of Carbohydrates in Subcritical Water Solubility of Carbohydrate in Subcritical Water Fernando Montañé 1, Tiziana Fornari 2, Elena Ibáñez 1, Keerthi Sriniva 3 Dongfang Zhang 3 and Jerry W. King *3 1 Intituto de Fermentacione Indutriale (CSIC).

More information

HEAT TRANSFER AND FLUID FLOW IN STATIONARY GTA WELDING OF γ-tial BASED ALLOYS: EFFECT OF THERMOCAPILLARY FLOW

HEAT TRANSFER AND FLUID FLOW IN STATIONARY GTA WELDING OF γ-tial BASED ALLOYS: EFFECT OF THERMOCAPILLARY FLOW Second International Conference on CFD in the Minerals and Process Industries CSIRO, Melbourne, Australia 6-8 December 999 HEAT TRANSFER AND FLUID FLOW IN STATIONARY GTA WELDING OF γ-tial BASED ALLOYS:

More information

REDUCTIONS IN ENERGY CONSUMPTION AND CO 2 EMISSIONS

REDUCTIONS IN ENERGY CONSUMPTION AND CO 2 EMISSIONS REDUCTIONS IN ENERGY CONSUMPTION AND CO EMISSIONS FOR GREENHOUSES HEATED WITH HEAT PUMPS Y. Tong, T. Kozai, N. Nihioka, K. Ohyama ABSTRACT. In the greenhoue indutry, it i eential to ue energy efficiently

More information

Numerical simulation of weld pool shape during laser beam welding

Numerical simulation of weld pool shape during laser beam welding International Research Journal of Applied and Basic Sciences. Vol., 3 (8), 1624-1630, 2012 Available online at http:// www. irjabs.com ISSN 2251-838X 2012 Numerical simulation of weld pool shape during

More information

Participation, Growth and Social Poverty: Social Capital in a Homogeneous

Participation, Growth and Social Poverty: Social Capital in a Homogeneous The Open Economic Journal, 2008,, -3 Open Acce Participation, Growth and Social Poverty: Social Capital in a Homogeneou Society Angelo Antoci *,, Pier Luigi Sacco 2 and Paolo Vanin 3 DEIR, Univerity of

More information

The Role of Skills Development in Competitiveness in Asia

The Role of Skills Development in Competitiveness in Asia The Role of Skill Development in Competitivene in Aia Profeor Michael J. Enright Univerity of Hong Kong Hong Kong Intitute for Economic and Buine Strategy Enright, Scott & Aociate ADB Copyright Michael

More information

Pigments Special Applications SAnODAL, SANODURe. For the dyeing of anodized aluminum

Pigments Special Applications SAnODAL, SANODURe. For the dyeing of anodized aluminum Pigment pecial Application AnODAL, ANODURe AND ANODYE DYE For the dyeing of anodized aluminum PRODUCT NAME Dark hade Light hade ANODYE Yellow 3GL ANODYE Yellow D ANODAL GOLD 4N ANODURE Fat Gold L ANODURE

More information

Aalborg Universitet. Published in: I E E E Transactions on Industrial Electronics. DOI (link to publication from Publisher): /TIE.2016.

Aalborg Universitet. Published in: I E E E Transactions on Industrial Electronics. DOI (link to publication from Publisher): /TIE.2016. Aalborg Univeritet Droop Control with Improved Diturbance Adaption for PV Sytem with Two Power Converion Stage Liu, Hongpeng; Loh, Poh Chiang; Wang, Xiongfei; Yang, Yongheng; Wang, Wei; Xu, Dianguo Publihed

More information

2nd International Conference on Production and Industrial Engineering CPIE-2010

2nd International Conference on Production and Industrial Engineering CPIE-2010 nd International Conference on Production and Indutrial Engineering CPIE- 59 Actie/Paie Damping Technique for iration control: - FEM aed deign and experimental iration control Sanji Kumar Raji Kumar Rakeh

More information

Fuzzy Decision Approach Based on QFD and FWA for Selection of Medical Suppliers

Fuzzy Decision Approach Based on QFD and FWA for Selection of Medical Suppliers , July 1-3, 2015, ondon,.k. Fuzzy Deciion Approach Baed on QFD and FWA for Selection of Medical Supplier Mehtap Durun and E. Ertugrul Karak Abtract The objective of thi paper i to develop a fuzzy multi-criteria

More information

Maximum Incremental Social Tolerable Irreversible Costs (MISTICs): Assessing Economic and

Maximum Incremental Social Tolerable Irreversible Costs (MISTICs): Assessing Economic and Maximum Incremental Social Tolerable Irreverible Cot (MISTIC): Aeing Economic and Ecological Impact of Innovation under Irreveribility and Uncertainty Sara SCATASTA, Department of Environmental and Reource

More information

CO 2 emissions trading planning in combined heat and power production via multi-period stochastic optimization

CO 2 emissions trading planning in combined heat and power production via multi-period stochastic optimization European Journal of Operational Reearch 176 (2007) 1874 1895 O.R. Application CO 2 emiion trading planning in combined heat and power production via multi-period tochatic optimization Aiying Rong *, Rito

More information

Modeling Reveals Bistability and Low-Pass Filtering in the Network Module Determining Blood Stem Cell Fate

Modeling Reveals Bistability and Low-Pass Filtering in the Network Module Determining Blood Stem Cell Fate Modeling Reveal Bitability and Low-Pa Filtering in the Network Module Determining Blood Stem Cell Fate Jatin Narula, Aileen M. Smith 2, Berthold Gottgen 2, Oleg A. Igohin * Department of Bioengineering,

More information

Characterization and Simulation of High Temperature Process

Characterization and Simulation of High Temperature Process Characterization and Simulation of High Temperature Process Session Chairs: Baojun Zhao Tarasankar DebRoy 469 7th International Symposium on High-Temperature Metallurgical Processing Edited by: Jiann-Yang

More information

Types of fracture in metals

Types of fracture in metals Type of fracture in metal The concept of material trength and fracture ha long been tudied to overcome failure. The introduction of malleable iron during the revolution of material contruction led to the

More information

Product Diversity and Ethnic Fragmentation: Is Heterogeneity Good or Bad for Media Capture?

Product Diversity and Ethnic Fragmentation: Is Heterogeneity Good or Bad for Media Capture? Product Diverity and Ethnic Fragmentation: I Heterogeneity Good or Bad for Media Capture? Caterina Gennaioli Preliminary Draft June 2008 Abtract Under ome circumtance a power eeking politician trie to

More information

Does Bait and Switch Really Benefit Consumers?

Does Bait and Switch Really Benefit Consumers? Doe Bait and Switch Really Benefit Conumer? William L. Wilkie Carl F. Mela Gregory T. Gundlach Univerity of Notre Dame, Notre Dame, Indiana 46556 william.l.wilkie.1@nd.edu Abtract While the field of marketing

More information

Evaluation of Tests To Assess Stripping Potential of Asphalt Concrete Mixtures

Evaluation of Tests To Assess Stripping Potential of Asphalt Concrete Mixtures 18 TRASPORTATIO RESEARCH RECORD 1171 Evaluation of Tet To Ae Stripping Potential of Aphalt Concrete Mixture FRAZIER PARKER JR., AD FouAD A. GHARAYBEH Stre pedetal, boll, and Indirect tenile tet were evaluated

More information

MARINE HEALTH, SAFETY, QUALITY, AND ENVIRONMENTAL MANAGEMENT

MARINE HEALTH, SAFETY, QUALITY, AND ENVIRONMENTAL MANAGEMENT Guide for Marine Health, Safety, Quality and Environmental Management GUIDE FOR MARINE HEALTH, SAFETY, QUALITY, AND ENVIRONMENTAL MANAGEMENT AUGUST 2009 (Updated November 2010 ee next page) American Bureau

More information

Int. J. Production Economics

Int. J. Production Economics Int. J. Production Economic 139 (212) 351 358 Content lit available at SciVere ScienceDirect Int. J. Production Economic journal homepage: www.elevier.com/locate/ijpe Dynamic inventory rationing for ytem

More information

Finite Element Simulation of Nd:YAG laser lap welding of AISI 304 Stainless steel sheets

Finite Element Simulation of Nd:YAG laser lap welding of AISI 304 Stainless steel sheets Finite Element Simulation of Nd:YAG laser lap welding of AISI 304 Stainless steel sheets N. SIVA SHANMUGAM 1*, G. BUVANASHEKARAN 2 AND K. SANKARANARAYANASAMY 1 1 Department of Mechanical Engineering, National

More information

MELT POOL GEOMETRY SIMULATIONS FOR POWDER-BASED ELECTRON BEAM ADDITIVE MANUFACTURING. Bo Cheng and Kevin Chou

MELT POOL GEOMETRY SIMULATIONS FOR POWDER-BASED ELECTRON BEAM ADDITIVE MANUFACTURING. Bo Cheng and Kevin Chou MELT POOL GEOMETRY SIMULATIONS FOR POWDER-BASED ELECTRON BEAM ADDITIVE MANUFACTURING Bo Cheng and Kevin Chou Mechanical Engineering Department The University of Alabama Tuscaloosa, AL 35487 Accepted August

More information

Thermochemical behavior of nano-sized aluminum-coated nickel particles

Thermochemical behavior of nano-sized aluminum-coated nickel particles J Nanopart Re (2014) 16:2392 DOI 10.1007/11051-014-2392-4 RESEARCH PAPER Thermochemical behavior of nano-ized aluminum-coated nickel particle Dilip Sriniva Sundaram Puneeh Puri Vigor Yang Received: 17

More information

Management Science Letters

Management Science Letters Management Science Letter 2 (2012) 3049 3054 Content lit available at GrowingScience Management Science Letter homepage: www.growingscience.com/ml Identification and prioritization of hazardou material

More information

PROJECT MANAGER. Preben Randhol. Inge Manfred Carlsen. CO 2 injeksjonsbrønner CO 2 nedbrytningsmekanismer

PROJECT MANAGER. Preben Randhol. Inge Manfred Carlsen. CO 2 injeksjonsbrønner CO 2 nedbrytningsmekanismer SINTEF Petroleumforkning AS SINTEF Petroleum Reearch NO-7465 Trondheim TITLE REPORT Ivaretakele av brønnintegritet ifm CO 2 injekjon (avrop nr: 6098-06-2007-705880) Enuring well integrity in connection

More information

Label Confusion: The Groucho Effect of Uncertain Standards. Rick Harbaugh, John W. Maxwell, and Beatrice Roussillon.

Label Confusion: The Groucho Effect of Uncertain Standards. Rick Harbaugh, John W. Maxwell, and Beatrice Roussillon. Label Confuion: The Groucho Effect of Uncertain Standard Rick Harbaugh, John W. Maxwell, and Beatrice Rouillon November 15, 21 Abtract Label certify that a product meet ome tandard for quality, but often

More information

A model for predicting time-dependent chloride binding. capacity of cement-fly ash cementitious system

A model for predicting time-dependent chloride binding. capacity of cement-fly ash cementitious system Material and Structure / Matériaux et ontruction, Vol. 37, July 2004, pp 387-396 A model for predicting time-dependent chloride binding capacity of cement-fly ah cementitiou ytem T. Sumranwanich and S.

More information