Chapter 6: Mechanical Properties

Size: px
Start display at page:

Download "Chapter 6: Mechanical Properties"

Transcription

1 Chapter 6: Mechanical Properties ISSUES TO ADDRESS... Stress and strain: What are they and why are they used instead of load and deformation? Elastic behavior: When loads are small, how much deformation occurs? What materials deform least? Plastic behavior: At what point does permanent deformation occur? What materials are most resistant to permanent deformation? Toughness and ductility: What are they and how do we measure them? Chapter 6-1

2 Elastic Deformation 1. Initial 2. Small load 3. Unload bonds stretch Elastic means reversible! F F return to initial Linearelastic Non-Linearelastic Chapter 6-2

3 Plastic Deformation (Metals) 1. Initial 2. Small load 3. Unload bonds stretch planes & planes still shear sheared elastic + plastic plastic F F Plastic means permanent! linear elastic plastic linear elastic Chapter 6-3

4 Tensile stress, : Engineering Stress Ft Shear stress, : Ft F Area, A o Area, A o Fs = F t lb f = 2 A o in original area before loading Ft or N 2 m = F s A o Fs F Stress has units: N/m 2 or lb f /in 2 Ft Chapter 6-4

5 Chapter 6-5

6 Common States of Stress Simple tension: cable F F Ao = cross sectional area (when unloaded) F A o Torsion (a form of shear): drive shaft A c M 2R M Fs A o F s A o Note: = M/A c R here. Ski lift (photo courtesy P.M. Anderson) Chapter 6-6

7 Chapter 6-7

8 OTHER COMMON STRESS STATES (i) Simple compression: A o Canyon Bridge, Los Alamos, NM (photo courtesy P.M. Anderson) Balanced Rock, Arches National Park (photo courtesy P.M. Anderson) F A o Note: compressive structure member ( < 0 here). Chapter 6-8

9 OTHER COMMON STRESS STATES (ii) Bi-axial tension: Hydrostatic compression: Pressurized tank (photo courtesy P.M. Anderson) > 0 Fish under water (photo courtesy P.M. Anderson) z > 0 < 0 h Chapter 6-9

10 Tensile strain: L o Engineering Strain w o /2 L o Lateral strain: L L w o Shear strain: x L /2 = x/y = tan y 90º 90º - Strain is always dimensionless. Adapted from Fig. 6.1(a) and (c), Callister & Rethwisch 8e. Chapter 6-10

11 Typical tensile test machine Stress-Strain Testing Typical tensile specimen extensometer specimen Adapted from Fig. 6.2, Callister & Rethwisch 8e. gauge length Adapted from Fig. 6.3, Callister & Rethwisch 8e. (Fig. 6.3 is taken from H.W. Hayden, W.G. Moffatt, and J. Wulff, The Structure and Properties of Materials, Vol. III, Mechanical Behavior, p. 2, John Wiley and Sons, New York, 1965.) Chapter 6-11

12 Linear Elastic Properties Modulus of Elasticity, E: (also known as Young's modulus) Hooke's Law: = E F E Linearelastic F simple tension test Chapter 6-12

13 Poisson's ratio, Poisson's ratio, : L L metals: ~ 0.33 ceramics: ~ 0.25 polymers: ~ Units: E: [GPa] or [psi] : dimensionless For isotropic materials < 0.50 (this is the value for which there is no net volume change) Chapter 6-13

14 Chapter 6-14

15 Chapter 6-15

16 Mechanical Properties Slope of stress strain plot (which is proportional to the elastic modulus) depends on bond strength of metal Adapted from Fig. 6.7, Callister & Rethwisch 8e. Chapter 6-16

17 Elastic Shear modulus, G: = G Other Elastic Properties G M simple torsion test Elastic Bulk modulus, K: P = -K V Vo Special relations for isotropic materials: G E 2(1 ) K P K E 3(1 2) V Vo P M P P pressure test: Init. vol =V o. Vol chg. = V Chapter 6-17

18 Young s Moduli: Comparison E(GPa) 10 9 Pa Metals Alloys Tungsten Molybdenum Steel, Ni Tantalum Platinum Cu alloys Zinc, Ti Silver, Gold Aluminum Magnesium, Tin Graphite Ceramics Semicond Diamond Si carbide Al oxide Si nitride <111> Si crystal <100> Glass -soda Concrete Graphite Polymers Composites /fibers Polyester PET PS PC PP HDPE PTFE LDPE Carbon fibers only CFRE( fibers)* Aramid fibers only AFRE( fibers)* Glass fibers only GFRE( fibers)* GFRE* CFRE* GFRE( fibers)* CFRE( fibers) * AFRE( fibers) * Epoxy only Wood( grain) Based on data in Table B.2, Callister & Rethwisch 8e. Composite data based on reinforced epoxy with 60 vol% of aligned carbon (CFRE), aramid (AFRE), or glass (GFRE) fibers. Chapter 6-18

19 Simple tension: Ao Useful Linear Elastic Relationships FL o EA o F L Fw o EA o /2 Simple torsion: 2ML o r o 4 G M = moment = angle of twist w o L o L o L /2 2r o Material, geometric, and loading parameters all contribute to deflection. Larger elastic moduli minimize elastic deflection. Chapter 6-19

20 Plastic (Permanent) Deformation (at lower temperatures, i.e. T < T melt /3) Simple tension test: engineering stress, Elastic+Plastic at larger stress Elastic initially permanent (plastic) after load is removed p engineering strain, plastic strain Adapted from Fig. 6.10(a), Callister & Rethwisch 8e. Chapter 6-20

21 Yield Strength, y Stress at which noticeable plastic deformation has occurred. when p = y tensile stress, y = yield strength Note: for 2 inch sample = = z/z z = in p = engineering strain, Adapted from Fig. 6.10(a), Callister & Rethwisch 8e. Chapter 6-21

22 2000 Yield Strength : Comparison Metals/ Alloys Steel (4140) qt Graphite/ Ceramics/ Semicond Polymers Composites/ fibers Yield strength, y (MPa) Ti (5Al-2.5Sn) W (pure) a Cu (71500) Mo (pure) cw Steel (4140) a Steel (1020) cd Al (6061) ag Steel (1020) hr Ti (pure) Ta (pure) a Cu (71500) hr Al (6061) a Hard to measure, since in tension, fracture usually occurs before yield. dry PC Nylon 6,6 PET humid PVC PP HDPE Hard to measure, in ceramic matrix and epoxy matrix composites, since in tension, fracture usually occurs before yield. Room temperature values Based on data in Table B.4, Callister & Rethwisch 8e. a = annealed hr = hot rolled ag = aged cd = cold drawn cw = cold worked qt = quenched & tempered 10 Tin (pure) LDPE Chapter 6-22

23 VMSE: Virtual Tensile Testing Chapter 6-23

24 Chapter 6-24

25 y Tensile Strength, TS Maximum stress on engineering stress-strain curve. TS engineering stress Typical response of a metal strain engineering strain Metals: occurs when noticeable necking starts. Polymers: occurs when polymer backbone chains are aligned and about to break. Adapted from Fig. 6.11, Callister & Rethwisch 8e. F = fracture or ultimate strength Neck acts as stress concentrator Chapter 6-25

26 Tensile strength, TS (MPa) Tensile Strength: Comparison Metals/ Alloys Steel (4140) qt W (pure) Ti (5Al-2.5Sn) Steel (4140) a a Cu (71500) Cu (71500) hr cw Steel (1020) Al (6061) Ti (pure) ag a Ta (pure) Al (6061) a Graphite/ Ceramics/ Semicond Diamond Si nitride Al oxide Si crystal <100> Glass-soda Concrete Graphite Polymers Nylon 6,6 PC PET PVC PP LDPE HDPE Composites/ fibers C fibers Aramid fib E-glass fib AFRE( fiber) GFRE( fiber) CFRE( fiber) wood( fiber) GFRE( fiber) CFRE( fiber) AFRE( fiber) wood ( fiber) Room temperature values Based on data in Table B.4, Callister & Rethwisch 8e. a = annealed hr = hot rolled ag = aged cd = cold drawn cw = cold worked qt = quenched & tempered AFRE, GFRE, & CFRE = aramid, glass, & carbon fiber-reinforced epoxy composites, with 60 vol% fibers. Chapter 6-26

27 Tensile strain at failure: Engineering tensile stress, Ductility smaller %EL larger %EL L %EL f L o L o x 100 A L o o A f L f Adapted from Fig. 6.13, Callister & Rethwisch 8e. Engineering tensile strain, Another ductility measure: A A f %RA = x 100 A o - o Chapter 6-27

28 Toughness Energy to break a unit volume of material Approximate by the area under the stress-strain curve. Engineering tensile stress, Adapted from Fig. 6.13, Callister & Rethwisch 8e. small toughness (ceramics) large toughness (metals) very small toughness (unreinforced polymers) Engineering tensile strain, Brittle fracture: elastic energy Ductile fracture: elastic + plastic energy Chapter 6-28

29 Resilience, U r Ability of a material to store energy Energy stored best in elastic region U r 0 y d If we assume a linear stress-strain curve this simplifies to U r 1 2 y y Adapted from Fig. 6.15, Callister & Rethwisch 8e. Chapter 6-29

30 Elastic Strain Recovery yi D yo Stress 2. Unload 1. Load 3. Reapply load Strain Adapted from Fig. 6.17, Callister & Rethwisch 8e. Elastic strain recovery Chapter 6-30

31 Hardness Resistance to permanently indenting the surface. Large hardness means: -- resistance to plastic deformation or cracking in compression. -- better wear properties. e.g., 10 mm sphere apply known force measure size of indent after removing load D d Smaller indents mean larger hardness. most plastics brasses Al alloys easy to machine steels file hard cutting tools nitrided steels diamond increasing hardness Chapter 6-31

32 Rockwell Hardness: Measurement No major sample damage Each scale runs to 130 but only useful in range Minor load 10 kg Major load 60 (A), 100 (B) & 150 (C) kg A = diamond, B = 1/16 in. ball, C = diamond HB = Brinell Hardness TS (psi) = 500 x HB TS (MPa) = 3.45 x HB Chapter 6-32

33 Hardness: Measurement Table 6.5 Chapter 6-33

34 True Stress & Strain Note: S.A. changes when sample stretched True stress True strain T F A i ln T i o T T 1 ln 1 Adapted from Fig. 6.16, Callister & Rethwisch 8e. Chapter 6-34

35 Chapter 6-35

36 Hardening An increase in y due to plastic deformation. y1 y0 large hardening small hardening Curve fit to the stress-strain response: T K n T hardening exponent: n = 0.15 (some steels) to n = 0.5 (some coppers) true stress (F/A) true strain: ln(l/l o ) Chapter 6-36

37 Variability in Material Properties Elastic modulus is material property Critical properties depend largely on sample flaws (defects, etc.). Large sample to sample variability. Statistics Mean n Standard Deviation s x i x 2 n 1 x n where n is the number of data points x n n 1 2 Chapter 6-37

38 Design or Safety Factors Design uncertainties mean we do not push the limit. Factor of safety, N working y N Often N is between 1.2 and 4 Example: Calculate a diameter, d, to ensure that yield does not occur in the 1045 carbon steel rod below. Use a factor of safety of 5. d 220,000N d 2 /4 working 5 y N d = m = 6.7 cm 1045 plain carbon steel: y = 310 MPa TS = 565 MPa F = 220,000N Chapter 6-38 Lo

39 Summary Stress and strain: These are size-independent measures of load and displacement, respectively. Elastic behavior: This reversible behavior often shows a linear relation between stress and strain. To minimize deformation, select a material with a large elastic modulus (E or G). Plastic behavior: This permanent deformation behavior occurs when the tensile (or compressive) uniaxial stress reaches y. Toughness: The energy needed to break a unit volume of material. Ductility: The plastic strain at failure. Chapter 6-39

40 Chapter 6-40

Chapter 6: Mechanical Properties

Chapter 6: Mechanical Properties Chapter 6: Mechanical Properties ISSUES TO ADDRESS... Stress and strain: What are they and why are they used instead of load and deformation? Elastic behavior: When loads are small, how much deformation

More information

Chapter 6: Mechanical Properties

Chapter 6: Mechanical Properties Chapter 6: Mechanical Properties ISSUES TO ADDRESS... Stress and strain: What are they and why are they used instead of load and deformation? Elastic behavior: When loads are small, how much deformation

More information

Chapter 8: Mechanical Properties of Metals. Elastic Deformation

Chapter 8: Mechanical Properties of Metals. Elastic Deformation Chapter 8: Mechanical Properties of Metals ISSUES TO ADDRESS... Stress and strain: What are they and why are they used instead of load and deformation? Elastic behavior: When loads are small, how much

More information

بسم الله الرحمن الرحیم. Materials Science. Chapter 7 Mechanical Properties

بسم الله الرحمن الرحیم. Materials Science. Chapter 7 Mechanical Properties بسم الله الرحمن الرحیم Materials Science Chapter 7 Mechanical Properties 1 Mechanical Properties Can be characterized using some quantities: 1. Strength, resistance of materials to (elastic+plastic) deformation;

More information

Chapter 6: Mechanical Properties

Chapter 6: Mechanical Properties Chapter 6: Mechanical Properties Elastic behavior: When loads are small, how much deformation occurs? What materials deform least? Stress and strain: What are they and why are they used instead of load

More information

ISSUES TO ADDRESS...

ISSUES TO ADDRESS... Chapter 7: Mechanical Properties School of Mechanical Engineering Choi, Hae-Jin Materials Science - Prof. Choi, Hae-Jin Chapter 7-1 ISSUES TO ADDRESS... Stress and strain: What are they and why are they

More information

CHAPTER 6: MECHANICAL PROPERTIES ISSUES TO ADDRESS...

CHAPTER 6: MECHANICAL PROPERTIES ISSUES TO ADDRESS... CHAPTER 6: MECHANICAL PROPERTIES ISSUES TO ADDRESS... Stress and strain: What are they and why are they used instead of load and deformation? Elastic behavior: When loads are small, how much deformation

More information

CHAPTER 6: Mechanical properties

CHAPTER 6: Mechanical properties CHAPTER 6: Mechanical properties ISSUES TO ADDRESS... Stress and strain: What are they and why are they used instead of load and deformation? Elastic behavior: When loads are small, how much deformation

More information

Chapter 7: Mechanical Properties

Chapter 7: Mechanical Properties Chapter 7: Mechanical Properties ISSUES TO ADDRESS... Stress and strain: What are they and why are they used instead of load and deformation? Elastic behavior: When loads are small, how much deformation

More information

Chapter 6: Mechanical Properties

Chapter 6: Mechanical Properties ISSUES TO ADDRESS... Stress and strain Elastic behavior: When loads are small, how much reversible deformation occurs? What material resist reversible deformation better? Plastic behavior: At what point

More information

Chapter 7: Mechanical Properties 1- Load 2- Deformation 3- Stress 4- Strain 5- Elastic behavior

Chapter 7: Mechanical Properties 1- Load 2- Deformation 3- Stress 4- Strain 5- Elastic behavior -1-2 -3-4 ( ) -5 ( ) -6-7 -8-9 -10-11 -12 ( ) Chapter 7: Mechanical Properties 1- Load 2- Deformation 3- Stress 4- Strain 5- Elastic behavior 6- Plastic behavior 7- Uniaxial tensile load 8- Bi-axial tensile

More information

AERO 214. Introduction to Aerospace Mechanics of Materials. Lecture 2

AERO 214. Introduction to Aerospace Mechanics of Materials. Lecture 2 AERO 214 Introduction to Aerospace Mechanics of Materials Lecture 2 Materials for Aerospace Structures Aluminum Titanium Composites: Ceramic Fiber-Reinforced Polymer Matrix Composites High Temperature

More information

Concepts of stress and strain

Concepts of stress and strain Chapter 6: Mechanical properties of metals Outline Introduction Concepts of stress and strain Elastic deformation Stress-strain behavior Elastic properties of materials Plastic deformation Yield and yield

More information

Chapter 7. Mechanical Properties

Chapter 7. Mechanical Properties Chapter 7 Mechanical Properties Chapter 7 Plastic Deformation, Ductility and Toughness Issues to address Stress and strain: What are they and why are they used instead of load and deformation? Elastic

More information

Chapter 6:Mechanical Properties

Chapter 6:Mechanical Properties Chapter 6:Mechanical Properties Why mechanical properties? Need to design materials that can withstand applied load e.g. materials used in building bridges that can hold up automobiles, pedestrians materials

More information

NDT Deflection Measurement Devices: Benkelman Beam (BB) Sri Atmaja P. Rosyidi, Ph.D., P.E. Associate Professor

NDT Deflection Measurement Devices: Benkelman Beam (BB) Sri Atmaja P. Rosyidi, Ph.D., P.E. Associate Professor NDT Deflection Measurement Devices: Benkelman Beam (BB) Sri Atmaja P. Rosyidi, Ph.D., P.E. Associate Professor NDT Deflection Measurement Devices on Pavement Structure NDT measurement of pavement surface

More information

Issues to address. Why Mechanical Test?? Mechanical Properties. Why mechanical properties?

Issues to address. Why Mechanical Test?? Mechanical Properties. Why mechanical properties? Mechanical Properties Why mechanical properties? Folsom Dam Gate Failure, July 1995 Need to design materials that can withstand applied load e.g. materials used in building bridges that can hold up automobiles,

More information

CHAPTER 7: MECHANICAL PROPERTIES

CHAPTER 7: MECHANICAL PROPERTIES CHAPTER 7: MECHANICAL PROPERTIES ISSUES TO ADDRESS... Stress and strain: What are they and why are they used instead of load and deformation? Elastic behavior: When loads are small, how much deformation

More information

ISSUES TO ADDRESS... What types of defects arise in solids? Can the number and type of defects be varied and controlled?

ISSUES TO ADDRESS... What types of defects arise in solids? Can the number and type of defects be varied and controlled? CHAPTER 4: IMPERFECTIONS IN SOLIDS ISSUES TO ADDRESS... What types of defects arise in solids? Can the number and type of defects be varied and controlled? How do defects affect material properties? Are

More information

Mechanical Properties

Mechanical Properties Stress-strain behavior of metals Elastic Deformation Plastic Deformation Ductility, Resilience and Toughness Hardness 108 Elastic Deformation bonds stretch δ return to initial Elastic means reversible!

More information

MECHANICAL PROPERTIES. (for metals)

MECHANICAL PROPERTIES. (for metals) MECHANICAL PROPERTIES (for metals) 1 Chapter Outline Terminology for Mechanical Properties The Tensile Test: Stress-Strain Diagram Properties Obtained from a Tensile Test True Stress and True Strain The

More information

CE205 MATERIALS SCIENCE PART_6 MECHANICAL PROPERTIES

CE205 MATERIALS SCIENCE PART_6 MECHANICAL PROPERTIES CE205 MATERIALS SCIENCE PART_6 MECHANICAL PROPERTIES Dr. Mert Yücel YARDIMCI Istanbul Okan University Deparment of Civil Engineering Chapter Outline Terminology for Mechanical Properties The Tensile Test:

More information

The Mechanical Properties of Polymers

The Mechanical Properties of Polymers The Mechanical Properties of Polymers Date: 14/07/2018 Abu Zafar Al Munsur Behavior Of Material Under Mechanical Loads = Mechanical Properties. Term to address here Stress and strain: These are size-independent

More information

Chapter 15: Characteristics, Applications & Processing of Polymers

Chapter 15: Characteristics, Applications & Processing of Polymers Chapter 15: Characteristics, Applications & Processing of Polymers Study: 15.1-15.14 Read: 15.15-15.24 What are the tensile properties of polymers and how are they affected by basic microstructural features?

More information

WEEK FOUR. This week, we will Define yield (failure) in metals Learn types of stress- strain curves Define ductility.

WEEK FOUR. This week, we will Define yield (failure) in metals Learn types of stress- strain curves Define ductility. WEEK FOUR Until now, we Defined stress and strain Established stress-strain relations for an elastic material Learned stress transformation Discussed yield (failure) criteria This week, we will Define

More information

Topic/content. By the end of this course : Why study? MATERIALS ENGINEERING SME 3623

Topic/content. By the end of this course : Why study? MATERIALS ENGINEERING SME 3623 MATERIALS ENGINEERING SME 3623 WWII Liberty Ships fracture into two halves Dr. Norhayati Ahmad Department of Materials Engineering Faculty of Mechanical Engineering, Universiti Teknologi Malaysia. E-mail:

More information

11/2/2018 7:58 PM. Chapter 6. Mechanical Properties of Metals. Mohammad Suliman Abuhaiba, Ph.D., PE

11/2/2018 7:58 PM. Chapter 6. Mechanical Properties of Metals. Mohammad Suliman Abuhaiba, Ph.D., PE 1 Chapter 6 Mechanical Properties of Metals 2 Assignment 7, 13, 18, 23, 30, 40, 45, 50, 54 4 th Exam Tuesday 22/11/2018 3 WHY STUDY Mechanical Properties of Metals? How various mechanical properties are

More information

CHAPTER 3 OUTLINE PROPERTIES OF MATERIALS PART 1

CHAPTER 3 OUTLINE PROPERTIES OF MATERIALS PART 1 CHAPTER 3 PROPERTIES OF MATERIALS PART 1 30 July 2007 1 OUTLINE 3.1 Mechanical Properties 3.1.1 Definition 3.1.2 Factors Affecting Mechanical Properties 3.1.3 Kinds of Mechanical Properties 3.1.4 Stress

More information

Welcome to ENR116 Engineering Materials. This lecture summary is part of module 2, Material Properties.

Welcome to ENR116 Engineering Materials. This lecture summary is part of module 2, Material Properties. Welcome to ENR116 Engineering Materials. This lecture summary is part of module 2, Material Properties. 1 2 Mechanical properties. 3 The intended learning outcomes from this lecture summary are that you

More information

Engineering Materials

Engineering Materials Engineering Materials Mechanical Properties of Engineering Materials Mechanical testing of engineering materials may be carried out for a number of reasons: The tests may simulate the service conditions

More information

MATERIALS SELECTION ECONOMIC, ENVIRON., & DESIGN ISSUES

MATERIALS SELECTION ECONOMIC, ENVIRON., & DESIGN ISSUES MATERIALS SELECTION ECONOMIC, ENVIRON., & DESIGN ISSUES ISSUES TO ADDRESS... Price and availability of materials. How do we select materials based on optimal performance? Applications: --shafts under torsion

More information

MECHANICAL PROPERTIES AND TESTS. Materials Science

MECHANICAL PROPERTIES AND TESTS. Materials Science MECHANICAL PROPERTIES AND TESTS Materials Science Stress Stress is a measure of the intensity of the internal forces acting within a deformable body. Mathematically, it is a measure of the average force

More information

Chapter Outline Mechanical Properties of Metals How do metals respond to external loads?

Chapter Outline Mechanical Properties of Metals How do metals respond to external loads? Chapter Outline Mechanical Properties of Metals How do metals respond to external loads?! Stress and Strain " Tension " Compression " Shear " Torsion! Elastic deformation! Plastic Deformation " Yield Strength

More information

SMU 2113 ENGINEERING SCIENCE. PART 1 Introduction to Mechanics of Materials and Structures

SMU 2113 ENGINEERING SCIENCE. PART 1 Introduction to Mechanics of Materials and Structures SMU 2113 ENGINEERING SCIENCE PART 1 Introduction to Mechanics of Materials and Structures These slides are designed based on the content of these reference textbooks. OBJECTIVES To introduce basic principles

More information

Chapter 16: Composite Materials

Chapter 16: Composite Materials Chapter 16: Composite Materials What are the classes and types of composites? Why are composites used instead of metals, ceramics, or polymers? How do we estimate composite stiffness & strength? What are

More information

Materials Science ME 274. Dr Yehia M. Youssef. Materials Science. Copyright YM Youssef, 4-Oct-10

Materials Science ME 274. Dr Yehia M. Youssef. Materials Science. Copyright YM Youssef, 4-Oct-10 ME 274 Dr Yehia M. Youssef 1 The Structure of Crystalline Solids Solid materials may be classified according to the regularity with which atoms or ions are arranged with respect to one another. A crystalline

More information

ME -215 ENGINEERING MATERIALS AND PROCESES

ME -215 ENGINEERING MATERIALS AND PROCESES ME -215 ENGINEERING MATERIALS AND PROCESES Instructor: Office: MEC325, Tel.: 973-642-7455 E-mail: samardzi@njit.edu PROPERTIES OF MATERIALS Chapter 3 Materials Properties STRUCTURE PERFORMANCE PROCESSING

More information

High Temperature Materials. By Docent. N. Menad. Luleå University of Technology ( Sweden )

High Temperature Materials. By Docent. N. Menad. Luleå University of Technology ( Sweden ) of Materials Course KGP003 Ch. 6 High Temperature Materials By Docent. N. Menad Dept. of Chemical Engineering and Geosciences Div. Of process metallurgy Luleå University of Technology ( Sweden ) Mohs scale

More information

Energy and Packing. typical neighbor bond energy. typical neighbor bond energy. Dense, regular-packed structures tend to have lower energy.

Energy and Packing. typical neighbor bond energy. typical neighbor bond energy. Dense, regular-packed structures tend to have lower energy. Energy and Packing Non dense, random packing Energy typical neighbor bond length typical neighbor bond energy r Dense, regular packing Energy typical neighbor bond length typical neighbor bond energy r

More information

Energy and Packing. Materials and Packing

Energy and Packing. Materials and Packing Energy and Packing Non dense, random packing Energy typical neighbor bond length typical neighbor bond energy r Dense, regular packing Energy typical neighbor bond length typical neighbor bond energy r

More information

CE 221: MECHANICS OF SOLIDS I CHAPTER 3: MECHANICAL PROPERTIES OF MATERIALS

CE 221: MECHANICS OF SOLIDS I CHAPTER 3: MECHANICAL PROPERTIES OF MATERIALS CE 221: MECHANICS OF SOLIDS I CHAPTER 3: MECHANICAL PROPERTIES OF MATERIALS By Dr. Krisada Chaiyasarn Department of Civil Engineering, Faculty of Engineering Thammasat university Outline Tension and compression

More information

Materials Engineering 272-C Fall 2001, Lectures 9 & 10. Introduction to Mechanical Properties of Metals

Materials Engineering 272-C Fall 2001, Lectures 9 & 10. Introduction to Mechanical Properties of Metals Materials Engineering 272-C Fall 2001, Lectures 9 & 10 Introduction to Mechanical Properties of Metals From an applications standpoint, one of the most important topics within Materials Science & Engineering

More information

Material Properties 3

Material Properties 3 Material Properties 3 Real Stress and Strain True M Corrected Stress M Engineering Strain Several Alloys Material n MPa psi Low-carbon steel 0.26 530 77,000 (annealed) Alloy steel 0.15 640 93,000 (Type

More information

3. MECHANICAL PROPERTIES OF STRUCTURAL MATERIALS

3. MECHANICAL PROPERTIES OF STRUCTURAL MATERIALS 3. MECHANICAL PROPERTIES OF STRUCTURAL MATERIALS Igor Kokcharov 3.1 TENSION TEST The tension test is the most widely used mechanical test. Principal mechanical properties are obtained from the test. There

More information

بسم هللا الرحمن الرحیم. Materials Science. Chapter 3 Structures of Metals & Ceramics

بسم هللا الرحمن الرحیم. Materials Science. Chapter 3 Structures of Metals & Ceramics بسم هللا الرحمن الرحیم Materials Science Chapter 3 Structures of Metals & Ceramics 1 ISSUES TO ADDRESS... How do atoms assemble into solid structures? How does the density of a material depend on its structure?

More information

Chapter 1. The Structure of Metals. Body Centered Cubic (BCC) Structures

Chapter 1. The Structure of Metals. Body Centered Cubic (BCC) Structures Chapter 1 The Structure of Metals Body Centered Cubic (BCC) Structures Figure 1. The body-centered cubic (bcc) crystal structure: (a) hard-ball model; (b) unit cell; and (c) single crystal with many unit

More information

Tensile/Tension Test Fundamentals

Tensile/Tension Test Fundamentals CIVE.3110 Engineering Materials Laboratory Fall 2016 Tensile/Tension Test Fundamentals Tzuyang Yu Associate Professor, Ph.D. Structural Engineering Research Group (SERG) Department of Civil and Environmental

More information

Mechanical Properties of Metals. Goals of this unit

Mechanical Properties of Metals. Goals of this unit Mechanical Properties of Metals Instructor: Joshua U. Otaigbe Iowa State University Goals of this unit Quick survey of important metal systems Detailed coverage of basic mechanical properties, especially

More information

Mechanical behavior of crystalline materials - Stress Types and Tensile Behaviour

Mechanical behavior of crystalline materials - Stress Types and Tensile Behaviour Mechanical behavior of crystalline materials - Stress Types and Tensile Behaviour 3.1 Introduction Engineering materials are often found to posses good mechanical properties so then they are suitable for

More information

Chapter 4 MECHANICAL PROPERTIES OF MATERIAL. By: Ardiyansyah Syahrom

Chapter 4 MECHANICAL PROPERTIES OF MATERIAL. By: Ardiyansyah Syahrom Chapter 4 MECHANICAL PROPERTIES OF MATERIAL By: Ardiyansyah Syahrom Chapter 2 STRAIN Department of Applied Mechanics and Design Faculty of Mechanical Engineering Universiti Teknologi Malaysia 1 Expanding

More information

Today s Topics. Plastic stress-strain behaviour of metals Energy of mechanical ldeformation Hardness testing Design/safety factors

Today s Topics. Plastic stress-strain behaviour of metals Energy of mechanical ldeformation Hardness testing Design/safety factors MME 291: Lecture 10 Mechanical Properties of Materials 2 Prof. A.K.M.B. Rashid Department of MME BUET, Dhaka Today s Topics Plastic stress- behaviour of metals Energy of mechanical ldeformation Hardness

More information

Mechanical Properties of Materials

Mechanical Properties of Materials INTRODUCTION Mechanical Properties of Materials Many materials, when in service, are subjected to forces or loads, it is necessary to know the characteristics of the material and to design the member from

More information

Chapter 2: Mechanical Behavior of Materials

Chapter 2: Mechanical Behavior of Materials Chapter : Mechanical Behavior of Materials Definition Mechanical behavior of a material relationship - its response (deformation) to an applied load or force Examples: strength, hardness, ductility, stiffness

More information

FME201 Solid & Structural Mechanics I Dr.Hussein Jama Office 414

FME201 Solid & Structural Mechanics I Dr.Hussein Jama Office 414 FME201 Solid & Structural Mechanics I Dr.Hussein Jama Hussein.jama@uobi.ac.ke Office 414 Lecture: Mon 11am -1pm (CELT) Tutorial Tue 12-1pm (E207) 10/1/2013 1 CHAPTER OBJECTIVES Show relationship of stress

More information

REVISED PAGES IMPORTANT TERMS AND CONCEPTS REFERENCES QUESTIONS AND PROBLEMS. 166 Chapter 6 / Mechanical Properties of Metals

REVISED PAGES IMPORTANT TERMS AND CONCEPTS REFERENCES QUESTIONS AND PROBLEMS. 166 Chapter 6 / Mechanical Properties of Metals 1496T_c06_131-173 11/16/05 17:06 Page 166 166 Chapter 6 / Mechanical Properties of Metals IMPORTANT TERMS AND CONCEPTS Anelasticity Design stress Ductility Elastic deformation Elastic recovery Engineering

More information

MECHANICAL PROPERTIES OF MATERIALS

MECHANICAL PROPERTIES OF MATERIALS MECHANICAL PROPERTIES OF MATERIALS Stress-Strain Relationships Hardness Effect of Temperature on Properties Fluid Properties Viscoelastic Behavior of Polymers Mechanical Properties in Design and Manufacturing

More information

MSE 170 Final review part 2

MSE 170 Final review part 2 MSE 170 Final review part 2 Exam date: 12/9/2008 Tues, 8:30-10:20 Place: Here! Closed book, no notes and no collaborations Two sheets of letter-sized paper with doublesided notes is allowed Exam is comprehensive:

More information

Metals are generally ductile because the structure consists of close-packed layers of

Metals are generally ductile because the structure consists of close-packed layers of Chapter 10 Why are metals ductile and ceramics brittle? Metals are generally ductile because the structure consists of close-packed layers of atoms that allow for low energy dislocation movement. Slip

More information

Price and Availability

Price and Availability Price and Availability Outline Introduction Relative cost of materials Example MECH 321 Mech. Eng. Dept. - Concordia University lecture 21/1 Current Prices on the web (a) : - Short term trends: fluctuations

More information

5. A round rod is subjected to an axial force of 10 kn. The diameter of the rod is 1 inch. The engineering stress is (a) MPa (b) 3.

5. A round rod is subjected to an axial force of 10 kn. The diameter of the rod is 1 inch. The engineering stress is (a) MPa (b) 3. The Avogadro's number = 6.02 10 23 1 lb = 4.45 N 1 nm = 10 Å = 10-9 m SE104 Structural Materials Sample Midterm Exam Multiple choice problems (2.5 points each) For each problem, choose one and only one

More information

MECHANICAL PROPERTIES PROPLEM SHEET

MECHANICAL PROPERTIES PROPLEM SHEET MECHANICAL PROPERTIES PROPLEM SHEET 1. A tensile test uses a test specimen that has a gage length of 50 mm and an area = 200 mm 2. During the test the specimen yields under a load of 98,000 N. The corresponding

More information

Chapter 8: Deformation & Strengthening Mechanisms. School of Mechanical Engineering Choi, Hae-Jin ISSUES TO ADDRESS

Chapter 8: Deformation & Strengthening Mechanisms. School of Mechanical Engineering Choi, Hae-Jin ISSUES TO ADDRESS Chapter 8: Deformation & Strengthening Mechanisms School of Mechanical Engineering Choi, Hae-Jin Materials Science - Prof. Choi, Hae-Jin Chapter 8-1 ISSUES TO ADDRESS Why are the number of dislocations

More information

Types of Strain. Engineering Strain: e = l l o. Shear Strain: γ = a b

Types of Strain. Engineering Strain: e = l l o. Shear Strain: γ = a b Types of Strain l a g Engineering Strain: l o l o l b e = l l o l o (a) (b) (c) Shear Strain: FIGURE 2.1 Types of strain. (a) Tensile. (b) Compressive. (c) Shear. All deformation processes in manufacturing

More information

Deformation, plastic instability

Deformation, plastic instability Deformation, plastic instability and yield-limited design Engineering Materials 2189101 Department of Metallurgical Engineering Chulalongkorn University http://pioneer.netserv.chula.ac.th/~pchedtha/ Material

More information

Workshop Practice TA 102

Workshop Practice TA 102 Workshop Practice TA 102 Lec 2 & 3 :Engineering Materials By Prof.A.Chandrashekhar Engineering Materials Materials play an important role in the construction and manufacturing of equipment/tools. Right

More information

The photograph of Figure (a)

The photograph of Figure (a) Chapter 6 Mechanical Properties of Metals 2000 TS (a) Stress (MPa) 1000 E Stress (MPa) 2000 y 1000 0 0 0 0.000 0.040 (b) Strain 0.010 Strain 0.080 The photograph of Figure (a) shows an apparatus that measures

More information

CHAPTER 4 1/1/2016. Mechanical Properties of Metals - I. Processing of Metals - Casting. Hot Rolling of Steel. Casting (Cont..)

CHAPTER 4 1/1/2016. Mechanical Properties of Metals - I. Processing of Metals - Casting. Hot Rolling of Steel. Casting (Cont..) Processing of Metals - Casting CHAPTER 4 Mechanical Properties of Metals - I Most metals are first melted in a furnace. Alloying is done if required. Large ingots are then cast. Sheets and plates are then

More information

Plastic stress-strain behaviour of metals Energy of mechanical ldeformation Hardness testing Design/safety factors

Plastic stress-strain behaviour of metals Energy of mechanical ldeformation Hardness testing Design/safety factors Mechanical Properties of Materials 2 Prof. A.K.M.B. Rashid Department of MME BUET, Dhaka Plastic stress-strain behaviour of metals Energy of mechanical ldeformation Hardness testing Design/safety factors

More information

Chapter 15: Characteristics, Applications & Processing of Polymers (1)

Chapter 15: Characteristics, Applications & Processing of Polymers (1) Chapter 15: Characteristics, Applications & Processing of Polymers (1) ISSUES TO ADDRESS... What are the tensile properties of polymers and how are they affected by basic microstructural features? Hardening,

More information

Reproducible evaluation of material properties. Static Testing Material response to constant loading

Reproducible evaluation of material properties. Static Testing Material response to constant loading Material Testing Material Testing Reproducible evaluation of material properties Static Testing Material response to constant loading Dynamic Testing Material response to varying loading conditions, including

More information

Page 1 of 46 Exam 1. Exam 1 Past Exam Problems without Solutions NAME: Given Formulae: Law of Cosines: C. Law of Sines:

Page 1 of 46 Exam 1. Exam 1 Past Exam Problems without Solutions NAME: Given Formulae: Law of Cosines: C. Law of Sines: NAME: EXAM 1 PAST PROBLEMS WITHOUT SOLUTIONS 100 points Tuesday, September 26, 2017, 7pm to 9:30 You are allowed to use a calculator and drawing equipment, only. Formulae provided 2.5 hour time limit This

More information

Chapter 7. Mechanical properties 7.1. Introduction 7.2. Stress-strain concepts and behaviour 7.3. Mechanical behaviour of metals 7.4.

Chapter 7. Mechanical properties 7.1. Introduction 7.2. Stress-strain concepts and behaviour 7.3. Mechanical behaviour of metals 7.4. Chapter 7. Mechanical properties 7.1. Introduction 7.2. Stress-strain concepts and behaviour 7.3. Mechanical behaviour of metals 7.4. Mechanical behaviour of ceramics 7.5. Mechanical behaviour of polymers

More information

The strength of a material depends on its ability to sustain a load without undue deformation or failure.

The strength of a material depends on its ability to sustain a load without undue deformation or failure. TENSION TEST The strength of a material depends on its ability to sustain a load without undue deformation or failure. This strength is inherent in the material itself and must be determined by experiment.

More information

True Stress and True Strain

True Stress and True Strain True Stress and True Strain For engineering stress ( ) and engineering strain ( ), the original (gauge) dimensions of specimen are employed. However, length and cross-sectional area change in plastic region.

More information

MECHANICS OF MATERIALS. Mechanical Properties of Materials

MECHANICS OF MATERIALS. Mechanical Properties of Materials MECHANICS OF MATERIALS Mechanical Properties of Materials By NUR FARHAYU ARIFFIN Faculty of Civil Engineering & Earth Resources Chapter Description Expected Outcomes Understand the concept of tension and

More information

TRUE STRESS AND STRAIN

TRUE STRESS AND STRAIN TRUE STRESS AND STRAIN TS M F Implies the material is getting weaker? Stress True stress Strain TRUE STRAIN True strain of system Assuming no volume change i.e. RELATION BETWEEN TRUE STRESS AND STRAIN

More information

3. Mechanical Properties of Materials

3. Mechanical Properties of Materials 3. Mechanical Properties of Materials 3.1 Stress-Strain Relationships 3.2 Hardness 3.3 Effect of Temperature on Properties 3.4 Fluid Properties 3.5 Viscoelastic Properties Importance of Mechanical Properties

More information

Materials of Engineering ENGR 151 CHARACTERISTICS, APPLICATIONS AND PROCESSING OF POLYMERS

Materials of Engineering ENGR 151 CHARACTERISTICS, APPLICATIONS AND PROCESSING OF POLYMERS Materials of Engineering ENGR 151 CHARACTERISTICS, APPLICATIONS AND PROCESSING OF POLYMERS POLYMER CRYSTALLINITY Crystalline regions thin platelets with chain folds at faces Chain folded structure Fig.

More information

Properties of Engineering Materials

Properties of Engineering Materials Properties of Engineering Materials Syllabus Mechanical Properties, Tensile, Fatigue, Creep, Impact, Hardness, Chemical Properties, Physical properties, Corrosion and Cathodic Protection, Carbon Steel,

More information

MATERIALS SCIENCE-44 Which point on the stress-strain curve shown gives the ultimate stress?

MATERIALS SCIENCE-44 Which point on the stress-strain curve shown gives the ultimate stress? MATERIALS SCIENCE 43 Which of the following statements is FALSE? (A) The surface energy of a liquid tends toward a minimum. (B) The surface energy is the work required to create a unit area of additional

More information

BFF1113 Engineering Materials DR. NOOR MAZNI ISMAIL FACULTY OF MANUFACTURING ENGINEERING

BFF1113 Engineering Materials DR. NOOR MAZNI ISMAIL FACULTY OF MANUFACTURING ENGINEERING BFF1113 Engineering Materials DR. NOOR MAZNI ISMAIL FACULTY OF MANUFACTURING ENGINEERING Course Guidelines: 1. Introduction to Engineering Materials 2. Bonding and Properties 3. Crystal Structures & Properties

More information

MME 2001 MATERIALS SCIENCE

MME 2001 MATERIALS SCIENCE MME 2001 MATERIALS SCIENCE 1 20.10.2015 crystal structures X tal structure Coord. # Atoms/ unit cell a=f(r) APF % SC 6 1 2R 52 BCC 8 2 4R/ 3 68 FCC 12 4 2R 2 74 HCP 12 6 2R 74 Theoretical Density, knowing

More information

Strengthening Mechanisms. Today s Topics

Strengthening Mechanisms. Today s Topics MME 131: Lecture 17 Strengthening Mechanisms Prof. A.K.M.B. Rashid Department of MME BUET, Dhaka Today s Topics Strengthening strategies: Grain strengthening Solid solution strengthening Work hardening

More information

Module 2 Selection of Materials and Shapes. IIT, Bombay

Module 2 Selection of Materials and Shapes. IIT, Bombay Module 2 Selection of Materials and Shapes Lecture 1 Physical and Mechanical Properties of Engineering Materials Instructional objectives At the of this lecture, the student should be able to appreciate

More information

Tutorial 2 : Crystalline Solid, Solidification, Crystal Defect and Diffusion

Tutorial 2 : Crystalline Solid, Solidification, Crystal Defect and Diffusion Tutorial 1 : Introduction and Atomic Bonding 1. Explain the difference between ionic and metallic bonding between atoms in engineering materials. 2. Show that the atomic packing factor for Face Centred

More information

Mechanical behavior of crystalline materials- Comprehensive Behaviour

Mechanical behavior of crystalline materials- Comprehensive Behaviour Mechanical behavior of crystalline materials- Comprehensive Behaviour In the previous lecture we have considered the behavior of engineering materials under uniaxial tensile loading. In this lecture we

More information

Quiz 1 - Mechanical Properties and Testing Chapters 6 and 8 Callister

Quiz 1 - Mechanical Properties and Testing Chapters 6 and 8 Callister Quiz 1 - Mechanical Properties and Testing Chapters 6 and 8 Callister You need to be able to: Name the properties determined in a tensile test including UTS,.2% offset yield strength, Elastic Modulus,

More information

Chapter 9: Dislocations & Strengthening Mechanisms. Why are the number of dislocations present greatest in metals?

Chapter 9: Dislocations & Strengthening Mechanisms. Why are the number of dislocations present greatest in metals? Chapter 9: Dislocations & Strengthening Mechanisms ISSUES TO ADDRESS... Why are the number of dislocations present greatest in metals? How are strength and dislocation motion related? Why does heating

More information

When an axial load is applied to a bar, normal stresses are produced on a cross section perpendicular to the axis of the bar.

When an axial load is applied to a bar, normal stresses are produced on a cross section perpendicular to the axis of the bar. 11.1 AXIAL STRAIN When an axial load is applied to a bar, normal stresses are produced on a cross section perpendicular to the axis of the bar. In addition, the bar increases in length, as shown: 11.1

More information

Materials Science. Chapter 7: Mechanical Properties. Common States of Stress. Engineering Stress. Ft F. A o ISSUES TO ADDRESS... σ = F A o.

Materials Science. Chapter 7: Mechanical Properties. Common States of Stress. Engineering Stress. Ft F. A o ISSUES TO ADDRESS... σ = F A o. In the Name f Gd Materials Science Dr Mhammad Heidari-Rarani Chapter 7: Mechanical Prperties ISSUES TO ADDRESS... Stress and strain: What are they and why are they used instead f lad and defrmatin? Elastic

More information

CHAPTER 12: mechanical properties of ceramics

CHAPTER 12: mechanical properties of ceramics CHAPTER 12: mechanical properties of ceramics ISSUES TO ADDRESS... Mechanical Properties: What special provisions/tests are made for ceramic materials? Chapter 12-1 COORDINATION # AND IONIC RADII Coordination

More information

Tensile/Tension Test Advanced Topics

Tensile/Tension Test Advanced Topics CIVE.3110 Engineering Materials Laboratory Fall 2017 Tensile/Tension Test Advanced Topics Tzuyang Yu Associate Professor, Ph.D. Structural Engineering Research Group (SERG) Department of Civil and Environmental

More information

ENGINEERING MATERIAL 100

ENGINEERING MATERIAL 100 Department of Applied Chemistry Division of Science and Engineering SCHOOL OF ENGINEERING ENGINEERING MATERIAL 100 Experiments 4 and 6 Mechanical Testing and Applications of Non-Metals Name: Yasmin Ousam

More information

Dislocations & Materials Classes. Dislocation Motion. Dislocation Motion. Lectures 9 and 10

Dislocations & Materials Classes. Dislocation Motion. Dislocation Motion. Lectures 9 and 10 Lectures 9 and 10 Chapter 7: Dislocations & Strengthening Mechanisms Dislocations & Materials Classes Metals: Disl. motion easier. -non-directional bonding -close-packed directions for slip. electron cloud

More information

CHAPTER 8 DEFORMATION AND STRENGTHENING MECHANISMS PROBLEM SOLUTIONS

CHAPTER 8 DEFORMATION AND STRENGTHENING MECHANISMS PROBLEM SOLUTIONS CHAPTER 8 DEFORMATION AND STRENGTHENING MECHANISMS PROBLEM SOLUTIONS Slip Systems 8.3 (a) Compare planar densities (Section 3.15 and Problem W3.46 [which appears on the book s Web site]) for the (100),

More information

Chapter 12: Structures & Properties of Ceramics

Chapter 12: Structures & Properties of Ceramics Chapter 12: Structures & Properties of Ceramics ISSUES TO ADDRESS... Review of structures for ceramics How are impurities accommodated in the ceramic lattice? In what ways are ceramic phase diagrams similar

More information

Lecture Outline. Mechanical Properties of Ceramics. Mechanical properties of ceramics. Mechanical properties of ceramics

Lecture Outline. Mechanical Properties of Ceramics. Mechanical properties of ceramics. Mechanical properties of ceramics Mechanical properties of ceramics Lecture Outline Mechanical properties of ceramics Applications of ceramics abrication of Glasses Glass properties Processing of Ceramics Dr. M. Medraj Mech. Eng. Dept.

More information

ME 212 EXPERIMENT SHEET #2 TENSILE TESTING OF MATERIALS

ME 212 EXPERIMENT SHEET #2 TENSILE TESTING OF MATERIALS ME 212 EXPERIMENT SHEET #2 TENSILE TESTING OF MATERIALS 1. INTRODUCTION & THEORY The tension test is the most commonly used method to evaluate the mechanical properties of metals. Its main objective is

More information

CHAPTER8. Failure Analysis and Prevention

CHAPTER8. Failure Analysis and Prevention CHAPTER8 Failure Analysis and Prevention The repetitive loading of engineering materials opens up additional opportunities for structural failure. Shown here is a mechanical testing machine, introduced

More information