The Manufacture and Test of (110) Orientated Silicon Based Micro Heat Exchanger

Size: px
Start display at page:

Download "The Manufacture and Test of (110) Orientated Silicon Based Micro Heat Exchanger"

Transcription

1 Tamkang Journal of Science and Engineering, Vol. 5, No. 3, pp (2002) 129 Te Manufacture and Test of (110) Orientated Silicon Based Micro Heat Excanger Sung-Wen Kang, Yu-Tang Cen and Guang-Sang Cang Department of Mecanical and Electro-Mecanical Engineering Tamkang University Tamsui, Taiwan 251, R.O.C. Abstract Te micro cross-flow eat excanger made of (110)-orientated silicon is fabricated by bulk micromacining tat is compatible wit semiconductor producing processes, and wafers wit undreds of ig aspect ratio cannels are bonded togeter by diffusion bonding wit aluminum as medium layers. Te core of te micro eat excanger is about cm 3, and te density of te eat transfer area is 15,294 m 2 /m 3. Using pure water as te working fluid, te Reynolds Numbers sow tat te fluid field is always laminar flow, and as te maximum pressure drop reaces 2.47 bar, te flow rate is greater tan 4.5 L/min. Te eat transfer measured between ot and cold fluid is 5 kw; te log mean temperature is greater tan 30 K, and tat makes te overall eat transfer coefficient up to 24.7 kw/m 2 -K, corresponds to a volumetric eat transfer coefficient of MW/m 3 -K. Except reacted on a few special cemicals, silicon as excellent properties in mecanics, eat transfer, and anti-corrosion, so te (110) silicon based micro eat excanger suits for te operations at ig temperature or in corrosive fluids. Te extremely small eat sink appears to ave a variety of current and potential applications in areas suc as micro-electronic cooling and biomedical processes were ig eat transfer power are required wit little weigt and small volume. Key Words: Micro Cross-Flow Heat Excanger, Bulk Micromacining, Heat Transfer Area, Pressure Drop, Heat Transfer Coefficient 1. Introduction Te development of micro eat excanger began wit solving te problem of eat dissipation in VLSI. In 1984, Tuckerman [1] used anisotropic etcing and precision mecanical sawing tecniques to manufacture about 280 µm deep microcannels in 500 µm tick (110) orientated silicon wafers. He reported a ybrid of direct contact and cold plate tecnologies using laminar water flow in te micropassages and absorbing eat flux of 150 W/cm 2. Bot Cross and Ramsaw [2] reported on a type of eat excanger called printed circuit eat excanger. Te cannels on te plates of te special eat excanger were macined by using cemical etcing metods, and te plates were bonded togeter by diffusion brazing. Te cannel size is 0.4 mm wide and 0.3 mm deep, and te volumetric eat transfer coefficient is 7 MW/m 3 -K.

2 130 Sung-Wen Kang et al. Hig-capacity micro eat excangers ave also been produced using diamond macining tecniques by Friedric and Kang [3], owever, te processes are not easy for batc-fabrication. In te present work, te cannel and complete device fabrication is using silicon wet etcing tecniques. Te typical process include mask-making, potoresist coating and baking, exposing, etcing and cleaning. Te anisotropic etcing of SCS was discovered in te early 1960s. In 1969, Lee [4] etced silicon wafers by organic etcants, and e found tat te etcing rates on (111) were very slow. Bean [5] reported tat te extremely ig ratio greater tan 650 to 1 were obtained in (110) orientation-dependent etcing. Bean reported tat te etcing rate of (110) silicon in 35% w.t. KOH was about 0.8 µm/min. at 80 ; Krause and Obermeler [6] proved tat te etcing rate and te aspect ratio of etced cannels would increase wit te concentration of KOH liquor in recent report. Studies of conventional compact eat excangers design teories were already completed by Kays and London [7]. Te metallic eat excanger [8] wit features tat range in size from µm ave termal resistances ranging from 0.07 to 0.12 /W cm at flow rates of water of ~20 L/ and pressures of N/m 2 and fabricated using sacrificial polymer mandrils. N. Saji, et al. [9] developed a compact laminar flow eat excanger wit stainless steel micro-tube, wic consists of 12 elements wit a total of 4800 stainless steel micro-tube. Eac element is formed wit 400 tubes tat ave an inner diameter of 0.5 mm, an outer diameter of 0.7 mm and is 310 mm long. In te major processes of fabricating te silicon based micro eat excanger, bonding is te key point. Direct bonding is one of te major bonding metods in semiconductor processes by te ydrate bonding on te wafer and eat treatments in ig temperature atmospere. Except anodic bonding and direct bonding, te diffusion bonding is te well-cosen metod to bond silicon wafer togeter in lower temperature. Because only a few studies in te micro eat excangers area ave been reported, researces are needed to investigate te basic design, fabrication and performance of te micro eat excangers to expand te developments and strengten teir reliability. Te objectives of tis researc were referred to design, fabricate and test a (110) silicon based micro cross-flow eat excanger. 2. Design A cross-flow arrangement was adopted in tis micro eat excanger design because tis arrangement greatly simplified te eader design at te entrance and exit of eac fluid. A generic design for a two-fluid, cross-flow plate eat excanger is sown in Figure 1. Figure 1. A generic plate-type cross-flow micro eat excanger Te purpose for using micro cannels is to acieve specific eat transfer performance, U, witin minimum weigt, material and volume constraints. Since te eat transfer in ot and cold fluids are Q = m c,m (T,i - T,o ) (1) Q c = m c c c,m (T c,o - T c,i ) (2) and te average eat transfer is Q m = 1/2 (Q + Q c ) (3) te overall eat transfer coefficient can be calculated from Q U = m A T F m (4) Were A is te total eat transfer area on one side, and F is te correction factor for a cross-flow eat excanger wit bot fluids unmixed. Te log mean temperature difference

3 Te Manufacture and Test of (110) Orientated Silicon Based Micro Heat Excanger 131 ( T - T )- ( T - T ),i c,i,o c,i T m = (5) T,i - Tc,i ln T,o - Tc,o Te total volumetric eat transfer surface coefficient could be expressed as U v = U B (6) In wic is te eat excanger eat transfer surface area per unit volume. Te overall eat transfer coefficient may be expressed as 1 UA 1 1 = + R w + (7) A A c Due to te ig termal conductivity of silicon and te small wafer tickness, a simple calculation sows tat te termal resistance of te wall (Rw) could be negligible compared wit te convection resistance. Because te cannels on te two sides ave almost te same geometry, mass flow rate, and eat transfer conditions, it is reasonable to assume tat te convection eat transfer coefficient must be te same on bot sides, terefore (8) c and simplify it sequentially to = 2U (9) Te Nusselt Number is of te form D Nu = (10) kf Te great advantage of using tin silicon wafers wit micro flow cannels is te ability to produce a very large ratio of eat transfer area per unit volume. In addition, te large termal resistance between te eat excanger plates is very low due to te tin, ig conductivity silicon walls. Te cross-flow eat excanger is made by stacking and bonding silicon wafers togeter wic ave ad flow cannels etced into tem by litograpy.te factors tat need to be addressed in te design of any of tese devices include eat transfer capacity, pressure drop, size and number of cannels, spacing between cannels, and internal deformation due to differential pressure and temperature. Any consideration of mecanical devices made from silicon must certainly take into account te mecanical beavior and properties of single-crystal-silicon. Te Young's modulus of silicon is N/cm 2, and as a value approacing tat of stainless steel. Te Knoop ardness of silicon (850 kg/mm 2 ) is almost twice as ig as nickel and iron. SCS as a tensile yield strengt of N/cm 2, wic is at least 3 times iger tan stainless steel wire. 3. Fabrication Litograpy tecnology is widely used for semi-conductor processes; it includes waferscleaning, growt of etcing mask, potoresist coating, exposure and develop, etcing, doping, etc., almost all of tem made a contribution to tis study. Tree etcant systems are of particular interest due to teir versatility: etylene diamine pyrocatecol (EDP) and water, KOH and water, HF, HNO 3, and acetic acid, (CH 3 COOH). In tis study, KOH system was used. KOH and water is orientation dependent and, in fact, exibits muc iger (110) to (111) etcing rate ratio tan EDP, and for tis reason it is especially useful for grooves etcing on (110) wafers since te large differential etcing ratio permits deep, ig aspect ratio grooves wit minimal undercut of te mask. Si 3 N 4 is te preferred masking material for ig aspect ratio, long KOH etcing cannels. We used 120 nm silicon nitride and 180 nm silicon dioxide as te etcing mask. Te concentration of etcant also influences te etcing rate effectively. Te etcing rate would ascend wit te quantity of ydrate in liquor. Generally speaking, te etcing rate of 40% w.t. would be larger tan tat of 25% w.t., because te ydrate in 25% w.t. KOH are more tan tat in 40% w.t. KOH. Temperature affects etcing rate significantly. Te etcing rate and temperature ave a relation tat could be expressed as R = R o exp(-e c /kt) (11) Te R o represents te Pre-Exponential Factor; in eq. (11), we understand tat te etcing rate will raise apparently wit temperature. K. E. Bean reported tat te (110) wafers were etced at about 0.8 µm/min. in 50% w.t. KOH at 80. In our study 40% w.t. KOH wit stirring at 65 was adopted, and it took about 400 minute to etc a 200 µm deep cannel; te misalignment was about 3 ~5, so tat te undercut beside te 40 mm wide cannel was about 5~10 µm. Figure 2 sows te micrograp of te cannels on te wafer.

4 132 Sung-Wen Kang et al. Figure 2. Te micrograp of te cannels on te wafer (wafer tickness: 370 µm, cross section of te cannels: 40 µm 200 µm, bottom tickness: 170 m, fin widt: 40 µm) Te pattern we designed is 15 mm wide and 25 mm long, and te cannel area is 10 mm wide by 10 mm long; tere are 125 cannels wit 40 µm widt and 200 µm dept in te cannel area. Temperature is te most influential variable during diffusion bonding. In any termally activated process an incremental cange in temperature will cause te greatest cange in process kinetics wen compared to most oter process variables. In addition, virtually all te mecanisms in diffusion bonding are temperature dependent. In general, te temperature at wic diffusion bonding will take place is above one alf of te absolute melting temperature. Time is closely related to temperature in wic most diffusion controlled reaction rates vary wit time. Experience indicates tat increasing bot te time and te pressure at bonding temperature increase joint strengt up to a limit. Beyond tis point no furter gains are acieved. Pressure is important just in te beginning wen te bonding takes place. Oxide layers will fracture and te grains will deform and contact one anoter between te working pieces if necessary pressure is given, but as te diffusion is ongoing, pressure is not as important as in te beginning. In tis researc low pressure is employed to avoid te tin walls on te silicon wafers being bulked, and te pressure of 240 kg/cm 2 was used for clamping te wafers Silicon as a ig melting point of more tan 1400, and te temperature at wic te diffusion bonding takes place would ig enoug to increase te complexity, for tis reason, a low melting point medium material will lower te bonding temperature, in addition, aluminum as a good diffusion property wit silicon, so we consider aluminum foils as te medium layers in te bonding processes. In tis researc, te aluminum foils were cleaned in a 5% ydrocloric acid for 5 minutes wit ultrasonic saking to remove alumina on te foils, and te silicon wafers were cleaned by te same way in litograpy. Te foils and wafers are ten stacked and clamped in a grapite clamp, and tey were placed in a diffusion bonding furnace, and were eated to 600 for one our, and te vacuum was approximately 15 µtorr. A micrograp of an edge of te micro eat excanger is sown in Figure 3. Figure 4 sows te packaged micro eat excanger by a 10-dollar coin. Figure 3. A micrograp of an edge of te micro eat excanger Figure 4. Te micro eat excanger (cannel eat transfer lengt: 0.9 cm, number of cannel on eac wafer: 125, number of wafer layers: 26, number of cannels on one side: 1625, free flow area: 13 mm 2, free flow area/ frontal area: 12.7 %, total eat transfer area on one side: 70.2 cm 2, total eat transfer volume: cm 3, total eat transfer area/ total volume: m 2 /m 3 ) 4. Test

5 Te Manufacture and Test of (110) Orientated Silicon Based Micro Heat Excanger 133 Figure 5 sows a scematic of te experimental apparatus used to test te micro eat excanger. To minimize te amount of equipment required, measurements were made using only DI water as te working fluid on bot ot and cold side of te eat excanger. A test setup contains separate measuring devices for measuring te flow, as well ot fluid as pressure and temperature at bot inlets and outlets of te micro eat excanger. Te ot and cold water was supplied in a close circuit from ot and cold water tank. Te same flow rate was used for bot streams by adjusting te control valves. Te water pressure and temperature were measured at te inlets and outlets respectively. cold fluid pump pump out out ot fluid tank filter filter cold fluid tank flow meter flow meter in Pressure transducer P c,1 T c,1 in P,1 P,o T,1 T,o Micro eat excanger P c,o T c,o Te data obtained in te experiments were pressure drop, flow rates, inlet and outlet temperatures from te bot sides of te eat excanger; te flow rates of bot sides were kept te same by controlling te valves. Te experimental procedures consisted of varying te flow rates and measuring te pressures, temperatures, and te flow Figure 5. Scematic of te experimental apparatus rates. Te calculations were carried out according to equations based on a single-pass, cross-flow eat excangers wit bot te ot and cold water unmixed. From te measurements of te mass flow rate, inlet and outlet temperatures, Reynolds number (Re), te eat transfer (Q), te

6 134 Sung-Wen Kang et al. corresponding overall eat transfer coefficient (), volumetric eat transfer coefficient (U v ) and could be calculated. Figure 6 sows te measured pressure drop on te ot side and cold side as a function of te water flow rate. We found te maximum pressure drop reaced 2.47 bar wen flow rate is 4.5 L/min. As we kept te inlet temperatures bot te ot and cold side in te same region, and only adjusted te flow rates, we could obtain corresponding log mean temperature differences, and tey are sown in Figure Cold Hot for te maximum flow rate measured were 820 on te ot side, and 440 on te cold side, tat is, only laminar flow occurred over te test range. Figure 9 sows te Nusselt number variation wit Reynolds number for bot te ot and cold sides. Te difference between te two curves is tat te Reynolds number range on te ot side is greater tan tat of te cold side due to te variation of te viscosity. 4 3 Uv U pressure drop, bar pressure drop, bar U, kw/m U, kw/m2-k 2 -K Uv Uv,, MW/m3-K flow rate,, l/min L/min Figure 6. Measured pressure drop as a function of te flow rate 8 T,i i Re, cold side Figure 8(a). U and U v as a function of Re on bot cold sides 4 3 Re, cold side Uv U 20 temperature, C Temperature, 6 4 LMTD calculated T,oT,o T c,0 Tc,o 6 4 LMTD.C, C U, U, kw/m2-k Uv Uv,, MW/m3-K 3 2 T Tc,o c,o flow rate,, l/min L/min Figure 7. Relationsip of te temperature and te flow Re, ot side Re, ot side Figure 8(b). U and U v as a function of Re on ot sides In Figure 8 te overall eat transfer coefficient (U) and te volumetric eat transfer coefficient (U v ) calculated from te measured data as been plotted versus te Reynolds number on te bot sides. Te igest measured U, 24.7 kw/m 2 -K, corresponds to an U v of MW/m 3 -K. Te Reynolds number

7 Te Manufacture and Test of (110) Orientated Silicon Based Micro Heat Excanger 135 Nu Nu Cold Hot Re Figure 9. Nu as a function of Re on bot ot and cold sides 5. Conclusion Micro manufacturing tecniques suc as litograpy processes and vacuum diffusion bonding were adopted to fabricate te silicon based micro eat excangers, wic ave dimensions an order of magnitude smaller tan in conventional compact eat excanger. Potential applications for te eat excanger are seen in areas suc as microelectronics cooling, aircraft, aerospace cooling and biomedical processes were ig eat transfer power are required wit little weigt and small volume. A test system was developed to measure micro eat excanger flow-friction and termal performance. Using DI water as te working fluid, about 5 kw of energy could be transferred in a cubical eat transfer volume of cm 3 wit a log mean temperature difference of about 30 K. Tis corresponds to a overall eat transfer coefficient of more tan 24.7 kw/m 2 -K, and volumetric eat transfer coefficient of MW/m 3 -K. A B c D E c F k Nomenclature eat excanger total transfer area on one side ratio of total eat transfer area on one side of te excanger to total volume of te excanger specific eat ydraulic diameter reactive activation energy eat excanger correction factor eat convection coefficient Boltzmann constant k f m Nu Q R R w T U U v c i m o termal conductivity of working fluid mass flow rate mass flow rate Nusselt Number eat transferred reactive rate termal resistance of wall temperature overall eat transfer coefficient volumetric eat transfer coefficient Subscripts cold fluid ot fluid inlet condition mean condition outlet condition References [1] Tuckerman, D. B., Heat-Transfer Microstructures for Integrated Circuits, P.D. Tesis, Department of Electronic Engineering, Stanford University, U.S.A. (1984). [2] Cross, W. T. and Ramsaw, C., Process Intensification Laminar Flow Heat Transfer, Cemical Engineering Researc & Design: Transaction of te Institute of Cemical Engineers, Vol. 64, pp (1986). [3] Friedric, C. R. and Kang, S. W., Micro Heat Excangers Fabricated by Diamond Macining, Precision Engineering, Vol. 16, pp (1994). [4] Lee D. B., Anisotropic Etcing of Silicon, Journal of Applied Pysics, Vol. 40, pp (1969). [5] Bean, K. E., Anisotropic Etcing of Silicon, IEEE Trans. Electron Devices, Vol. ED-25, pp (1978). [6] Krause P. and Obermeler E, Etc and Surface Rougness of Deep Narrow U-Grooves in (110)-Orientated Silicon, J. of Micromec. Microeng., Vol. 5, pp (1992). [7] Kays, W. M. and London A. L., Compact Heat Excangers, 3rd. ed. McGraw Hill Co. N.Y., U.S.A. (1964). [8] Arias, F., Oliver, S. R. J., Xu, B., Holmlin, R. E. and Witesides, G. M., Fabrication of Metallic Heat Excangers Using Sacrificial Polymer Mandrils, Journal of Microelectromecanical System, Vol. 10, pp (2001). [9] Saji, N., Nagai, S., Tsucyia, K., Asakura, H. and Obata, M., Development of a compact

8 136 Sung-Wen Kang et al. laminar flow eat excanger wit stainless steel micro-tubes, Pysica C 345, pp (2001). Manuscript Received: Mar. 21, 2002 and Accepted: Jun. 26, 2002

Optimized geothermal binary power cycles

Optimized geothermal binary power cycles Optimized geotermal binary power cycles Kontoleontos E., Mendrinos D., Karytsas C. Centre for Renewable Energy Sources, 9t km Maratonos ave., 9009 Pikermi Attikis, Greece ABSTRACT Tis study as been carried

More information

A Low-Temperature Creep Experiment Using Common Solder

A Low-Temperature Creep Experiment Using Common Solder A Low-Temperature Creep Experiment Using Common Solder L. Roy Bunnell, Materials Science Teacer Soutridge Hig Scool Kennewick, WA 99338 roy.bunnell@ksd.org Abstract: Tis experiment uses common lead-tin

More information

Melt Pool Size Control in Thin-Walled and Bulky Parts via Process Maps

Melt Pool Size Control in Thin-Walled and Bulky Parts via Process Maps Melt Pool Size Control in Tin-Walled and Bulky Parts via Process Maps Aditad Vasinonta, Jack L. Beut and Raymond Ong Department of Mecanical Engineering Carnegie Mellon University Pittsburg, PA 15213 Abstract

More information

Forging. Types of Forging Dies. Open-Die Forging. Outline. Forging. Types of forging Forging analysis Examples

Forging. Types of Forging Dies. Open-Die Forging. Outline. Forging. Types of forging Forging analysis Examples Forging Outline Forging Types of forging Forging analysis Examples Oldest of te metal forming operations, dating from about 5000 B C Components: engine cranksafts, connecting rods, gears, aircraft structural

More information

FORMING OF MICROSTRUCTURE OF THE AL-SI-FE-MN SYSTEM ALLOY BY EQUAL CHANNEL ANGULAR PRESSING WITH BACKPRESSURE

FORMING OF MICROSTRUCTURE OF THE AL-SI-FE-MN SYSTEM ALLOY BY EQUAL CHANNEL ANGULAR PRESSING WITH BACKPRESSURE FORMING OF MICROSTRUCTURE OF THE AL-SI-FE-MN SYSTEM ALLOY BY EQUAL CHANNEL ANGULAR PRESSING WITH BACKPRESSURE Abdrakman NAIZABEKOV (1), Violetta ANDREYACHSHENKO (1), Jiri KLIBER (2) (1)Karaganda State

More information

Scaling Effects in Laser-Based Additive Manufacturing Processes

Scaling Effects in Laser-Based Additive Manufacturing Processes Scaling Effects in Laser-Based Additive Manufacturing Processes Andrew J. Birnbaum and Jack L. Beut Department of Mecanical Engineering Carnegie Mellon University Pittsburg, Pa 15213 James W. Sears Advanced

More information

ANALYSIS OF TENSION MEMBERS

ANALYSIS OF TENSION MEMBERS CHATER Structural Steel Design LRFD Metod Tird Edition ANALYSIS OF TENSION MEMBERS A. J. Clark Scool of Engineering Department of Civil and Environmental Engineering art II Structural Steel Design and

More information

Thermal Management Analysis of a Lithium-Ion Battery Pack using Flow Network Approach

Thermal Management Analysis of a Lithium-Ion Battery Pack using Flow Network Approach Avestia Publising International Journal of Mecanical Engineering and Mecatronics Volume 1, Issue 1, Year 1 ISSN: 199-74 Article ID: 011, DOI: 10.11159/ijmem.1.011 88 Termal Management Analysis of a Litium-Ion

More information

Introduction of Prediction Method of Welding Deformation by Using Laminated Beam Modeling Theory and Its Application to Railway Rolling Stock

Introduction of Prediction Method of Welding Deformation by Using Laminated Beam Modeling Theory and Its Application to Railway Rolling Stock IJR International Journal of Railway Vol., No. 4 / December 009, pp. 175-179 Introduction of Prediction Metod of Welding Deformation by Using Laminated Beam Modeling Teory and Its Application to Railway

More information

OPTICAL AND THERMAL INVESTIGATIONS OF CRYSTALLIZATION FOULING IN A MICRO HEAT EXCHANGER

OPTICAL AND THERMAL INVESTIGATIONS OF CRYSTALLIZATION FOULING IN A MICRO HEAT EXCHANGER Proceedings of International Conference on Heat Excanger Fouling and Cleaning - 2 (Peer-reviewed) June 5 -, 2, Crete Island, Greece Editors: M.R. Malayeri, A.P. H. Müller-Steinagen Watkinson and H. and

More information

Residential and public use. Permanently damp environments and direct contact with water. Outdoors, use pro-part inox. Do not use in pools.

Residential and public use. Permanently damp environments and direct contact with water. Outdoors, use pro-part inox. Do not use in pools. Data seet pro-telo Metal decorative profile for ceramic wall tiles. Flangeless metallic line for tiles of any tickness. Available in a wide variety of materials, finises and dimensions, tey represent an

More information

PHASE CHANGE MATERIALS

PHASE CHANGE MATERIALS 18 TECHNOOGY REVIEW: PHASE CHANGE MATERIAS Qpedia continues its review of tecnologies developed for electronics cooling applications. We are presenting selected patents tat were awarded to developers around

More information

Recap: Greenhouse Effect

Recap: Greenhouse Effect Recap: Greenouse Effect Relies on fact tat glass (or plastic) is transparent to visible radiation but opaque to infra-red (IR) radiation. E,g. Car window closed visible radiation only transmitted. Car

More information

The effect of operating temperature on the performance of Molten Carbonate Fuel Cell systems

The effect of operating temperature on the performance of Molten Carbonate Fuel Cell systems Te effect of operating temperature on te performance of Molten Carbonate Fuel Cell systems A. Musa, H.J. Steeman, M. De aepe (Department of Flow, Heat and Combustion Mecanics, Gent University- UGent, Sint-ietersnieuwstraat

More information

Experimentation on Pool Boiling With Sodium Dodecyl Sulfate

Experimentation on Pool Boiling With Sodium Dodecyl Sulfate International Journal of Engineering Researc and Development e-issn: 2278-067X, p-issn: 2278-800X, www.ijerd.com Volume 12, Issue 12 (December 2016), PP.45-53 Experimentation on Pool Boiling Wit Sodium

More information

Residential and public use. Permanently damp environments and direct contact with water. Outdoors, use pro-part inox. Do not use in pools.

Residential and public use. Permanently damp environments and direct contact with water. Outdoors, use pro-part inox. Do not use in pools. Data seet pro-telo Metal decorative profile for ceramic wall tiles. Flangeless metallic line for tiles of any tickness. Available in a wide variety of materials, finises and dimensions, tey represent an

More information

Floor decoration. Residential and public use. Permanently damp environments and direct contact with water.

Floor decoration. Residential and public use. Permanently damp environments and direct contact with water. Data seet Rigt angle profile for corners and wall and floor tile coverings. Decorative use as a metallic line. is a rigt angle, corner saped profile, wit bot sides of te same lengt. Tis design makes a

More information

HT 800 WP. The interchangeable insert drilling system GÜHRING - YOUR WORLD-WIDE PARTNER

HT 800 WP. The interchangeable insert drilling system GÜHRING - YOUR WORLD-WIDE PARTNER PRICELIST 42/2013 For extreme process reliability From ole diameter 11 to 40.0 For drilling depts 1.5xD, 3xD, 5xD, 7xD and 10xD Wit intercangeable inserts for steel, stainless steel, cast iron and Al Holders/intercangeable

More information

Evaluating adaptability of filtration technology to high-turbidity water purification

Evaluating adaptability of filtration technology to high-turbidity water purification Evaluating adaptability of filtration tecnology to ig-turbidity water purification Hiroyuki Takino*, Yuici Izutsu*, Mami Nakamaci*, Daiji Nagasio* *Hansin Water Supply Autority, Kobe City, Japan, 658-73

More information

Hydrodynamics of electric arc furnace bath at stirring with inert gases. S.V. Kazakov, M.P. Gulyaev, V.V. Filippov RUE BMZ, Moscow State Institute of

Hydrodynamics of electric arc furnace bath at stirring with inert gases. S.V. Kazakov, M.P. Gulyaev, V.V. Filippov RUE BMZ, Moscow State Institute of Hydrodynamics of electric arc furnace bat at stirring wit inert gases. S.V. Kazakov, M.P. Gulyaev, V.V. Filippov RUE BMZ, Moscow State Institute of Steel and Alloys. It is [-3] known, tat metal bottom

More information

Estimation of Critical Stress in Jointed Concrete Pavement

Estimation of Critical Stress in Jointed Concrete Pavement Available online at www.sciencedirect.com ScienceDirect Procedia - Social and Beavioral Scien ce s 04 ( 03 ) 08 7 nd Conference of Transportation Researc Group of India (nd CTRG) Estimation of Critical

More information

Conventional Paper I Determine time required in minutes for a 50mm diameter steel sphere

Conventional Paper I Determine time required in minutes for a 50mm diameter steel sphere Conventional aper I-04. (a) Give reasons wy te Carnot cycle cannot be considered as te teoretical cycle for steam power plants even toug its efficiency is te igest for te given eat source and sink temperatures.

More information

Mitigating autogenous shrinkage of hardening concrete

Mitigating autogenous shrinkage of hardening concrete Mitigating autogenous srinkage of ardening concrete H.W.M. van der Ham, E.A.B. Koenders & K. van Breugel Delft University of Tecnology, Delft, Neterlands ABSTRACT: Te probability of early age cracking

More information

Standard Test Method for Fracture Strength in Cleavage of Adhesives in Bonded Metal Joints 1

Standard Test Method for Fracture Strength in Cleavage of Adhesives in Bonded Metal Joints 1 Designation: D 3433 99 Standard Test Metod for Fracture Strengt in Cleavage of Adesives in Bonded Metal Joints 1 Tis standard is issued under te fixed designation D 3433; te number immediately following

More information

COMPARISON OF FINNED TUBE AND PLATE-FINNED HEAT EXCHANGERS IN WASTE HEAT RECOVERY

COMPARISON OF FINNED TUBE AND PLATE-FINNED HEAT EXCHANGERS IN WASTE HEAT RECOVERY Mario olik Marija Živić Zdravko Virag Antun Barac ttps://doi.org/10.178/tof.4si101 ISSN 1333-114 eissn 1849-1391 OMPARISON OF FINNED TUBE AND PLATE-FINNED EAT EXANGERS IN WASTE EAT REOVERY Summary Te use

More information

Open Access The Current Situation and Development of Fire Resistance Design for Steel Structures in China

Open Access The Current Situation and Development of Fire Resistance Design for Steel Structures in China Te Open Construction and Building Tecnology Journal, 010, 4, 55-63 55 Open Access Te Current Situation and Development of Fire Resistance Design for Steel Structures in Cina Jinceng Zao* and Xiuying Yang

More information

Development of Lithium Bromide-Water Absorption Heat Pump System for Simultaneous Production of Heated-up Air and Steam From Waste Heat

Development of Lithium Bromide-Water Absorption Heat Pump System for Simultaneous Production of Heated-up Air and Steam From Waste Heat HEFT214 1 t International Conference on Heat Transfer, Fluid Mecanics and Termodynamics 14 16 July 214 Orlando, Florida Development of Litium Bromide-Water bsorption Heat Pump System for Simultaneous Production

More information

THERMOELECTRIC COOLING MODULES OF INCREASED COOLING POWER ALTEC - 027, 031, 033, 035, 036

THERMOELECTRIC COOLING MODULES OF INCREASED COOLING POWER ALTEC - 027, 031, 033, 035, 036 . KRAINE. THERMOELECTRIC COOLING MODLES OF INCREASED COOLING POWER ALTEC - 2, 31, 33, 35, 36 Information is given on Peltier modules of incriased cooling power: Altec-2, Altec-31, Altec, Altec-35, Altec-36.

More information

Passing services without the need of routing the walls.

Passing services without the need of routing the walls. Data seet Metallic skirting for floor tile coverings. Metallic profiles for skirtings. Tey ave a ig mecanical resistance wit a functional, modern design. Specially recommended for office floors and raised

More information

DRAFT PAPER MODELING AND VISUALIZATION FOR IMAGING OF SUBSURFACE DAMAGE

DRAFT PAPER MODELING AND VISUALIZATION FOR IMAGING OF SUBSURFACE DAMAGE 7t Middle East NDT Conference & Exibition Gulf International Convention Center, Gulf Hotel Manama, Kingdom of Barain September 13-16, 2015 MODELING AND VISUALIZATION FOR IMAGING OF SUBSURFACE DAMAGE Neil

More information

TECHNICAL NOTE. On Cold-Formed Steel Construction DESIGN CONSIDERATIONS FOR FLEXURAL AND LATERAL-TORSIONAL BRACING

TECHNICAL NOTE. On Cold-Formed Steel Construction DESIGN CONSIDERATIONS FOR FLEXURAL AND LATERAL-TORSIONAL BRACING TECHNICAL NOTE On Cold-Formed Steel Construction Ligt Gauge Steel Engineers Association Wasington, D.C. Toll-Free: 1 (866) 465-4732 www.lgsea.com $5.00 DESIGN CONSIDERATIONS FOR FLEXURAL AND LATERAL-TORSIONAL

More information

HOUSEHOLD SOLID WASTE RECYCLING INDUCED PRODUCTION VALUES AND EMPLOYMENT OPPORTUNITIES IN TAIWAN

HOUSEHOLD SOLID WASTE RECYCLING INDUCED PRODUCTION VALUES AND EMPLOYMENT OPPORTUNITIES IN TAIWAN Journal of Minerals & Materials Caracterization & Engineering, Vol. 1, No.2, pp121-129, 2002 Printed in te USA. All rigts reserved HOUSEHOLD SOLID WASTE RECYCLING INDUCED PRODUCTION VALUES AND EMPLOYMENT

More information

Using Matrix to Solving the Probabilistic Inventory Models (Demand Model)

Using Matrix to Solving the Probabilistic Inventory Models (Demand Model) IAAST ONLINE ISSN 77-1565 PRINT ISSN 0976-488 CODEN: IAASCA International Arcive of Applied Sciences and Tecnology IAAST; Vol 4 [3] September 013: 09-15 01 Society of Education, India [ISO9001: 008 Certified

More information

BOD 5 removal kinetics and wastewater flow pattern of stabilization pond system in Birjand

BOD 5 removal kinetics and wastewater flow pattern of stabilization pond system in Birjand vailable online at www.pelagiaresearclibrary.com European Journal of Experimental Biology, 2013, 3(2):430-436 ISSN: 2248 9215 CODEN (US): EJEBU BOD 5 removal kinetics and wastewater flow pattern of stabilization

More information

A Study on Pendulum Seismic Isolators for High-Rise Buildings

A Study on Pendulum Seismic Isolators for High-Rise Buildings ctbu.org/papers Title: Autors: Subjects: Keywords: A Study on Pendulum Seismic Isolators for Hig-Rise Buildings Ikuo Tatemici, Maeda Corp. Mamoru Kawaguci, Kawaguci & Engineers Masaru Abe, Hosei University

More information

Outboard Engine Emissions: Modelling and Simulation of Underwater Propeller Velocity Profile using the CFD Code FLUENT

Outboard Engine Emissions: Modelling and Simulation of Underwater Propeller Velocity Profile using the CFD Code FLUENT 6 t Australasian Fluid Mecanics Conference Crown Plaza, Gold Coast, Australia 2-7 December 2007 Outboard Engine Emissions: Modelling and Simulation of Underwater Propeller Velocity Profile using te CFD

More information

Residential and public use. Permanently damp environments and direct contact with water. Do not use in pools.

Residential and public use. Permanently damp environments and direct contact with water. Do not use in pools. Data seet pro-corner Metallic profile for protecting wall tiles corners. Rigt angle, metallic profiles for protecting corners. Most of te pro-corner models are installed after te tile, wic implies a small

More information

Optimization of New 25A-size Metal Gasket Design Based on Contact Width Considering Forming and Contact Stress Effect

Optimization of New 25A-size Metal Gasket Design Based on Contact Width Considering Forming and Contact Stress Effect World Academy of Science, Engineering and Tecnology International Journal of Mecanical, Aerospace, Industrial, Mecatronic and Manufacturing Engineering Vol:6, No:3, 2012 Optimization of New 25A-size Metal

More information

The energy and exergy analysis of a novel cogeneration organic Rankine power and twostage compression refrigeration cycle

The energy and exergy analysis of a novel cogeneration organic Rankine power and twostage compression refrigeration cycle Energy Equip. Sys./ Vol. 5/No.3/September 2017/ 299-312 Energy Equipment and Systems ttp://energyequipsys.ut.ac.ir www.energyequipsys.com Te energy and exergy analysis of a novel cogeneration organic Rankine

More information

technicalmonograph Natural ventilation strategies for refurbishment projects Can we avoid mechanical ventilation?

technicalmonograph Natural ventilation strategies for refurbishment projects Can we avoid mechanical ventilation? tecnicalmonograp 3 Natural ventilation strategies for refurbisment projects Tis tecnical monograp is one of a set produced as part of te REVIVAL project an EU Energie Programme supported demonstration

More information

THE MICRO-HARDNESS ANISOTROPY OF FLUOR-OLIGOMERIC AND Fe-Co-W COATINGS

THE MICRO-HARDNESS ANISOTROPY OF FLUOR-OLIGOMERIC AND Fe-Co-W COATINGS HARDMEKO 27 Recent Advancement of Teory and Practice in Hardness Measurement 19-21 November, 27, Tsukuba, Japan THE MICRO-HARDNESS ANISOTROPY OF FLUOR-OLIGOMERIC AND Fe-Co-W COATINGS Vytautas Vasauskas,

More information

PREDICTION OF METAL PLASTICITY DURING THE METAL FORMING PROCESS. Y.E. Beygelzimer (DonSTU, Ukraine), D.V. Orlov (DonSTU, Ukraine)

PREDICTION OF METAL PLASTICITY DURING THE METAL FORMING PROCESS. Y.E. Beygelzimer (DonSTU, Ukraine), D.V. Orlov (DonSTU, Ukraine) PREDICTION OF METAL PLASTICITY DURING THE METAL FORMING PROCESS Y.E. Beygelzimer (DonSTU, Ukraine), D.V. Orlov (DonSTU, Ukraine) ABSTRACT Te matematical model of plastic deformation of structurally inomogeneous

More information

MEEG 346 Thermal Laboratory

MEEG 346 Thermal Laboratory MEEG 346 Termal Laboratory Experiment #4: Te Four-Stroke Combustion Engine Introduction Small engines are used in many applications. Tey are used to power motorcycles, lawnmowers, go-carts, and even small

More information

THE ROYAL STATISTICAL SOCIETY 2009 EXAMINATIONS SOLUTIONS HIGHER CERTIFICATE MODULE 8 SURVEY SAMPLING AND ESTIMATION

THE ROYAL STATISTICAL SOCIETY 2009 EXAMINATIONS SOLUTIONS HIGHER CERTIFICATE MODULE 8 SURVEY SAMPLING AND ESTIMATION THE ROYAL STATISTICAL SOCIETY 009 EXAMINATIONS SOLUTIONS HIGHER CERTIFICATE MODULE 8 SURVEY SAMPLING AND ESTIMATION Te Society provides tese solutions to assist candidates preparing for te examinations

More information

Measurement and Reporting of Vapor Phase Mercury Emissions from Low-Emitting Stationary Sources (DRAFT 9/25/08)

Measurement and Reporting of Vapor Phase Mercury Emissions from Low-Emitting Stationary Sources (DRAFT 9/25/08) Measurement and Reporting of Vapor Pase Mercury Emissions from Low-Emitting Stationary Sources (DRAFT 9/25/08) 1. Scope and Application Te purpose of tis protocol is to establis procedures for te measurement

More information

Geothermal Energy For Residential Co-Generation

Geothermal Energy For Residential Co-Generation Geotermal Energy For Residential Co-Generation COROIU Miaela PD student Electrical Engineering Faculty, Tecnical University of Cluj-Napoca, Romania Energy Efficiency Director Energobit S.A. Cluj-Napoca,

More information

A Review to Increase Productive Output of An Active Solar Distillation System

A Review to Increase Productive Output of An Active Solar Distillation System A Revi to Increase Productive Output of An Active Solar Distillation System UMANG R SONI 1, Dr. P.K.BRAHMBHATT 2, HEMANT B PATEL 1P.d Student, Department of Mecanical Engineering, PAHER, Udaipur, Rajastan,

More information

2.36 Bridge Inspections. Introduction. Scope and Objective. Conclusions

2.36 Bridge Inspections. Introduction. Scope and Objective. Conclusions Introduction Te Department of Works, Services and Transportation is responsible for construction, inspection and maintenance of bridges in te provincial road system. Te Transportation Services Division

More information

R-20F method: An approach for measuring the isolation effect of foams used fighting forest fires

R-20F method: An approach for measuring the isolation effect of foams used fighting forest fires AARMS Vol. 11, No. 2 (2012) 233 247 TECHNOLOGY R-20F metod: An approac for measuring te isolation effect of foams used figting forest fires ÁGOSTON RESTÁS* National University of Public Service, Budapest,

More information

STERILE CONTAINER SYSTEMS

STERILE CONTAINER SYSTEMS »» 1/2 Half Size 1/2 STANDARD MODEL 280 mm 285 mm Specificiations Lid (Perforated) Lid (Perforated) Safety Lid Safety Lid Sizes Box (Non Perforated) Box (Perforated) Box (Non Perforated) Box (Perforated)

More information

( h) ( ) Effect of Boiler Pressure (Using Molliar Diagram i.e., h-s diagram) We have, but W P << W T. = = h h h h

( h) ( ) Effect of Boiler Pressure (Using Molliar Diagram i.e., h-s diagram) We have, but W P << W T. = = h h h h Effect of Boiler Pressure (Using Molliar Diagram i.e., -s diagram) We ave, ( 3 ) ( 4 ) η t but W P P > P for te fixed

More information

Study of Combined Rice Husk Gasifier Thermoelectric Generator

Study of Combined Rice Husk Gasifier Thermoelectric Generator Available online at www.sciencedirect.com ScienceDirect Energy Procedia 5 (014 ) 159 166 013 International Conference on Alternative Energy in Developing Countries and Emerging Economies Study of Combined

More information

Indirect Evaporative cooling systems: modelling and performance analysis

Indirect Evaporative cooling systems: modelling and performance analysis Available online at www.sciencedirect.com ScienceDirect Energy Procedia 140 (2017) 475 485 www.elsevier.com/locate/procedia AiCARR 50t International Congress; Beyond NZEB Buildings, 10-11 May 2017, Matera,

More information

MEMS Fabrication. Beyond Integrated Circuits. MEMS Basic Concepts

MEMS Fabrication. Beyond Integrated Circuits. MEMS Basic Concepts MEMS Fabrication Beyond Integrated Circuits MEMS Basic Concepts Uses integrated circuit fabrication techniques to make mechanical as well as electrical components on a single chip. Small size 1µm 1mm Typically

More information

Performance and Properties of a High Power Light Source for EUV Lithography.

Performance and Properties of a High Power Light Source for EUV Lithography. Performance and Properties of a Hig Power Ligt Source for EUV Litograpy. I.V. Fomenkov, R.M. Ness, I.R. Oliver, S.T. Melnycuk, O.V. Kodykin, N.R. Böwering, C.L Rettig, J.R. Hoffman. Tis work was partially

More information

ABSTRACT INTRODUCTION

ABSTRACT INTRODUCTION Journal Journal o Cemical o Cemical Tecnology and and Metallurgy, 5, 3, 5, 25, 3, 25 38-33 STUD OF BROADENING IN A COMBINED PROCESS ROLLING - PRESSING USING AN EQUAL-CHANNEL STEP DIE Adrakman Naizaekov,

More information

Granular filtration LAB EXPERIMENTS

Granular filtration LAB EXPERIMENTS DRINKING WATER - LAB EXPERIMENTS LAB EXPERIMENTS Granular filtration Hydraulics granular filtration - ydraulics lab experiments Framework Tis module explains te lab experiments on te ydraulics of filtration.

More information

Construction and Building Materials

Construction and Building Materials Construction and Building Materials 25 (211) 3 38 Contents lists available at ScienceDirect Construction and Building Materials journal omepage: www.elsevier.com/locate/conbuildmat Comparison of different

More information

Air Atomizing Design, Features & Introduction

Air Atomizing Design, Features & Introduction Atomizing Design, Features & Introduction atomizing spray nozzles produces fine mist spray wit te elp of compressed air, liquid breaks into small droplets as air provides saring effects on liquid droplets.

More information

SHEAR AND FLEXURAL BEHAVIOR OF FERRO CEMENT DEEP BEAMS

SHEAR AND FLEXURAL BEHAVIOR OF FERRO CEMENT DEEP BEAMS IJRET: International Journal of Researc in Engineering and Tecnology eissn: 319-1163 pissn: 31-7308 SHEAR AND FLEXURAL BEHAVIOR OF FERRO CEMENT DEEP BEAMS Md Itesam Hussain 1,Vaijanat Halalli, P.M.B Raj

More information

Theoretical power density from salinity gradients using reverse electrodialysis

Theoretical power density from salinity gradients using reverse electrodialysis Available online at www.sciencedirect.com Energy Procedia 0 (01 ) 170 184 Tecnoport EC esearc 01 Teoretical power density from salinity gradients using reverse electrodialysis David A. Vermaas a,b*, Enver

More information

Reaction Characteristics of CaSO 4 / CaSO 4 1/2H 2 O Reversible Reaction for Chemical Heat Pump

Reaction Characteristics of CaSO 4 / CaSO 4 1/2H 2 O Reversible Reaction for Chemical Heat Pump oi:.252/jcej.7we22; release online on October, 27 28- October, 27, Kyoto, Japan IMPRES Paper ID: A9 Reaction Caracteristics of CaSO / CaSO /2H 2 O Reversible Reaction for Cemical Heat Pump Hironao OGURA

More information

Nonconventional Technologies Review no. 3/2009

Nonconventional Technologies Review no. 3/2009 Nonconventional Tecnologies Review no. /2009 CONSTRUCTIVE AND FUNCTIONAL UPGRADING OPPORTUNITIES FOR THE HEAT SECTION FROM UNIVERSITY OF ORADEA Cercetător ştiințific III Cristian VANCEA, Centrul de cercetări

More information

ASSESSMENT OF THE POWER CURVE FLATTENING METHOD: AN APPROACH TO SMART GRIDS

ASSESSMENT OF THE POWER CURVE FLATTENING METHOD: AN APPROACH TO SMART GRIDS ASSESSENT OF THE POWER CURVE FLATTENING ETHOD: AN APPROACH TO SART GRIDS S. CARILLO APARICIO F. J. LEIVA ROJO Giacomo PETRETTO Gianluca GIGLIUCCI SmartGrids Endesa Red I+D Endesa S.A. Enel Ingegneria e

More information

ANALYSIS OF DEEPSTALL LANDING FOR UAV

ANALYSIS OF DEEPSTALL LANDING FOR UAV 26 TH INTERNATIONAL CONGRE OF THE AERONAUTICAL CIENCE ANALYI OF DEEPTALL LANDING FOR UAV Hiroki Taniguci* *Te University of Tokyo Keywords: stall landing, UAV, landing metod Abstract Deepstall landing

More information

Improved Fuzzy Load Models by Clustering Techniques in Distribution Network Control

Improved Fuzzy Load Models by Clustering Techniques in Distribution Network Control International Journal on Electrical Engineering and Informatics - Volume 3, Number 2, 20 Improved Fuzzy Load Models by Clustering Tecniques in Distribution Network Control George Grigoras, P.D. * and George

More information

Effect Weibull Distribution Parameters Calculating Methods on Energy Output of a Wind Turbine: A Study Case

Effect Weibull Distribution Parameters Calculating Methods on Energy Output of a Wind Turbine: A Study Case Int. J. of Termal & Environmental Engineering Volume 14, No. 2 (2017) 163-173 Effect Weibull Distribution Parameters Calculating Metods on Energy Output of a Wind Turbine: Study Case beer Qawasmi, Suil

More information

Effect of alumina nanoparticles in the fluid on heat transfer in double-pipe heat exchanger system

Effect of alumina nanoparticles in the fluid on heat transfer in double-pipe heat exchanger system Korean J. Chem. Eng., 25(5), 966-971 (2008) SHORT COMMUNICATION Effect of alumina nanoparticles in the fluid on heat transfer in double-pipe heat exchanger system Byung-Hee Chun, Hyun Uk Kang, and Sung

More information

Power-Aware Task Scheduling for Dynamic Voltage Selection and Power Management for Multiprocessors

Power-Aware Task Scheduling for Dynamic Voltage Selection and Power Management for Multiprocessors Power-Aware Task Sceduling for Dynamic Voltage Selection and Power Management for Multiprocessors HyunJin Kim 1, Jin-o An 2, Hong-Sik Kim 1 and Sungo Kang 1 1 Department of Electrical and Electronic Engineering,

More information

Nonconventional Technologies Review no. 1/2010 ASPECTS OF SURFACE MICROGEOMETRY MACHINING BY ULTRASONIC AIDED PLANE LAPPING

Nonconventional Technologies Review no. 1/2010 ASPECTS OF SURFACE MICROGEOMETRY MACHINING BY ULTRASONIC AIDED PLANE LAPPING ASPECTS OF SURFACE MICROGEOMETRY MACHINING BY ULTRASONIC AIDED PLANE LAPPING Liliana TULCAN 1, Miaela NISTORAN BOTIS 2, Aurel TULCAN 3 1 University Politenica from Timisoara, Romania, liliana.tulcan@gmail.com

More information

Buckling Capacity Optimization of Stiffened Rectangular Plate under Uniform Normal Compression

Buckling Capacity Optimization of Stiffened Rectangular Plate under Uniform Normal Compression JOURNAL OF COMPUTERS, VOL. 9, NO., MARCH 4 8 Buckling Capacity Optimization of Stiffened Rectangular Plate under Uniform Normal Compression Haifeng Fang a,b, Liua Cai a,b a Mecatronics & Automotive Engineering

More information

REDUCE PEAK-TIME ENERGY USE BY DEMAND BIDDING PROGRAM IN IRAN

REDUCE PEAK-TIME ENERGY USE BY DEMAND BIDDING PROGRAM IN IRAN REDUCE PEAK-TIME ENERGY USE BY DEMAND BIDDING PROGRAM IN IRAN Hossein DELAVARIPOUR Hossein.delavary@yaoo.com Amir KHAZAEE Amir.kazaee@ymail.com Meran GHASEMPOOR Gasempour.meran@gmail.com Hossein HOOSHMANDI

More information

Crosstalk between three-dimensional plasmonic slot waveguides

Crosstalk between three-dimensional plasmonic slot waveguides Crosstalk between tree-dimensional plasmonic slot waveguides Georgios Veronis and Sanui Fan Department of Electrical Engineering, Stanford University, Stanford, California 94305 sanui@stanford.edu Abstract:

More information

0.3 to 0.18 W/mK (depending on construction) by CSTB

0.3 to 0.18 W/mK (depending on construction) by CSTB CI/SfB Xt6 September 2017 Contents System components 2 Applications 3 resistances 4-6 considerations 7 Installation guidance 8 Isotec Termally Insulated Balcony Connectors Ancon Isotec Isotec is a ig performance

More information

E ect of step geometry and water quality on e ciency of cascade aeration

E ect of step geometry and water quality on e ciency of cascade aeration Scientia Iranica A (2016) 23(3), 918{925 Sarif University of Tecnology Scientia Iranica Transactions A: Civil Engineering www.scientiairanica.com Researc Note E ect of step geometry and water quality on

More information

UC Berkeley Research Reports

UC Berkeley Research Reports UC Berkeley Researc Reports Title Crane Double Cycling in Container Ports: Affect on Sip Dwell Time Permalink ttps://escolarsip.org/uc/item/9qp7p7jq Autors Goodcild, Anne V. Daganzo, Carlos F. Publication

More information

ANCAMINE 2726 Curing Agent

ANCAMINE 2726 Curing Agent Epoxy Curing Agents and Modifiers ANCAMINE 2726 Curing Agent DESCRIPTION Ancamine 2726 curing agent is a modified cycloalipatic amine adduct intended for use at ambient temperatures wit liquid epoxy resins.

More information

Delamination Cracking in Thermal Barrier Coating System

Delamination Cracking in Thermal Barrier Coating System Y. C. Zou Fracture Researc Institute, Tooku University, Sendai 980-8579, Japan and Institute of Fundamental Mecanics and Materials Engineering, Xiangtan University, Xiangtan, Hunan 405, P. R. Cina e-mail:

More information

The Division of Labour under Uncertainty. Nigel Wadeson *

The Division of Labour under Uncertainty. Nigel Wadeson * Te Division of Labour under Uncertainty By Nigel Wadeson * Date of First Submission: 19 t May, 011 Date of Second Submission: 9t May, 01 How to cite tis paper: Wadeson, Nigel (013), "Te Division of Labour

More information

THE ENERGY SAVING POTENTIAL OF MEMBRANE-BASED ENTHALPY RECOVERY IN VAV SYSTEMS FOR COMMERCIAL OFFICE BUILDINGS

THE ENERGY SAVING POTENTIAL OF MEMBRANE-BASED ENTHALPY RECOVERY IN VAV SYSTEMS FOR COMMERCIAL OFFICE BUILDINGS SiBuild Fift National Conference of IBPSA-USA THE ENERGY SAVING POTENTIAL OF MEMBRANE-BASED ENTHALPY RECOVERY IN VAV SYSTEMS FOR COMMERCIAL OFFICE BUILDINGS Liping Wang, Pilip Haves, and Jon Bresears 2

More information

Design and Performance Characterization of a Micro-pin-fin sco 2 Recuperator

Design and Performance Characterization of a Micro-pin-fin sco 2 Recuperator Design and Performance Characterization of a Micro-pin-fin sco 2 Recuperator Cameron Naderi, Graduate Student Erfan Rasouli, Post Doctoral Scholar Vinod Narayanan*, Professor sco 2 Symposium, Pittsburg

More information

Referrals in Search Markets

Referrals in Search Markets eferrals in Searc Markets Maria Arbatskaya and Hideo Konisi June 29, 2010 Abstract Tis paper compares te equilibrium outcomes in searc markets wit and witout referrals. Altoug it seems clear tat consumers

More information

Performance Improvement on Water-cooled Cold-Plate

Performance Improvement on Water-cooled Cold-Plate Proceedings of the 4th WSEAS International Conference on Heat and Mass Transfer, Gold Coast, Queensland, Australia, January 17-19, 2007 104 Performance Improvement on Water-cooled Cold-Plate SHYAN-FU CHOU,

More information

DYNAMIC ROOF CRUSH INTRUSION IN INVERTED DROP TESTING

DYNAMIC ROOF CRUSH INTRUSION IN INVERTED DROP TESTING DYNAMIC ROOF CRUSH INTRUSION IN INVERTED DROP TESTING Stepen A. Batzer, P.D., P.E. Renfroe Engineering, Inc. United States of America Robert M. Hooker Eliseco Systems United States of America Paper Number

More information

EFFECTIVE UTILIZATION OF FLYWHEEL ENERGY STORAGE (FES) FOR FREQUENCY REGULATION SERVICE PROVISION MIRAT TOKOMBAYEV THESIS

EFFECTIVE UTILIZATION OF FLYWHEEL ENERGY STORAGE (FES) FOR FREQUENCY REGULATION SERVICE PROVISION MIRAT TOKOMBAYEV THESIS EFFECTIVE UTILIZATION OF FLYWHEEL ENERGY STORAGE (FES) FOR FREQUENCY REGULATION SERVICE PROVISION BY MIRAT TOKOMBAYEV THESIS Submitted in partial fulfillment of te requirements for te degree of Master

More information

Experimental Analysis of Integrated System of Membrane Distillation for Pure Water with Solar Domestic Hot Water

Experimental Analysis of Integrated System of Membrane Distillation for Pure Water with Solar Domestic Hot Water Experimental Analysis of Integrated System of Membrane Distillation for Pure Water wit Solar Domestic Hot Water Muammad Asim Master of Science Tesis KTH Scool of Industrial Engineering and Management Energy

More information

Transportation Research Forum

Transportation Research Forum Transportation Researc Forum Comparison of Alternative Metods for Estimating Houseold Trip Rates of Cross-Classification Cells wit Inadequate Data Autor(s): Judit L. Mwakalonge and Daniel A. Badoe Source:

More information

A NOVEL INTEGRATED ENERGY SYSTEM OF SOLAR POWER, HEAT PUMPS AND AI-EV (AIR-CONDITIONER ELECTRIC VEHICLE)

A NOVEL INTEGRATED ENERGY SYSTEM OF SOLAR POWER, HEAT PUMPS AND AI-EV (AIR-CONDITIONER ELECTRIC VEHICLE) t International Conference on Heat Transfer, Fluid Mecanics and Termodynamics HEFAT6 t International Conference on Heat Transfer, Fluid Mecanics and Termodynamics July 6 Malaga, Spain A NOVEL INTEGRATED

More information

A Thermal Analysis and Optimization of a Combined Cycle by Several Technologies

A Thermal Analysis and Optimization of a Combined Cycle by Several Technologies American Journal of Energy Researc, 2014, Vol. 2, No. 2, 5-41 Available online at ttp://pubs.sciepub.com/ajer/2/2/ Science and Education Publising DOI:10.12691/ajer-2-2- A ermal Analysis and Optimization

More information

ME 189 Microsystems Design and Manufacture. Chapter 9. Micromanufacturing

ME 189 Microsystems Design and Manufacture. Chapter 9. Micromanufacturing ME 189 Microsystems Design and Manufacture Chapter 9 Micromanufacturing This chapter will offer an overview of the application of the various fabrication techniques described in Chapter 8 in the manufacturing

More information

OPTIMAL CONTROL OF A SOLAR GREENHOUSE. R.J.C. van Ooteghem, J.D. Stigter, L.G. van Willigenburg, G. van Straten

OPTIMAL CONTROL OF A SOLAR GREENHOUSE. R.J.C. van Ooteghem, J.D. Stigter, L.G. van Willigenburg, G. van Straten OPTIMAL CONTROL OF A SOLAR GREENHOUSE R.J.C. van Ootegem, J.D. Stigter, L.G. van Willigenburg, G. van Straten Systems and Control Group, Department o Agrotecnology and Food Science, Wageningen University,

More information

Chapter 3 Silicon Device Fabrication Technology

Chapter 3 Silicon Device Fabrication Technology Chapter 3 Silicon Device Fabrication Technology Over 10 15 transistors (or 100,000 for every person in the world) are manufactured every year. VLSI (Very Large Scale Integration) ULSI (Ultra Large Scale

More information

10. Design Optimization Overview

10. Design Optimization Overview 10. Design Optimization Overview November 2013 QII52021-13.1.0 QII52021-13.1.0 Tis capter introduces eatures in Altera s Quartus II sotware tat you can use to acieve te igest design perormance wen you

More information

Convective heat transfer and flow characteristics of Cu-water nanofluid

Convective heat transfer and flow characteristics of Cu-water nanofluid Vol. 45 No. 4 SCIENCE IN CHINA (Series E) August 2002 Convective heat transfer and flow characteristics of Cu-water nanofluid LI Qiang XUAN Yimin School of Power Engineering, Nanjing University of Science

More information

Optimization of maintenance strategies and ROI analysis of CMS through RAM-LCC analysis. A wind energy sector case study.

Optimization of maintenance strategies and ROI analysis of CMS through RAM-LCC analysis. A wind energy sector case study. 8t European Worksop On Structural Healt Monitoring (EWSHM 2016), 5-8 July 2016, Spain, Bilbao www.ndt.net/app.ewshm2016 Optimization of maintenance strategies and ROI analysis of CMS troug RAM-LCC analysis.

More information

Draft for Public Comment Australian/New Zealand Standard

Draft for Public Comment Australian/New Zealand Standard COMMITTEE EL-056 DR AS/NZS 3823.4.2:2014 Amd 1:2016 (Project ID: 103934 Draft for Public Comment Australian/New Zealand Standard LIABLE TO ALTERATION DO NOT USE AS A STANDARD BEGINNING DATE FOR COMMENT:

More information

Consumer price indices: provisional data December 2015

Consumer price indices: provisional data December 2015 5 January 2016 Consumer price indices: provisional data December 2015 In December 2015, according to provisional estimates, te Italian consumer price index for te wole nation (NIC) eld steady on montly

More information

JEL codes: F10, F12, F14

JEL codes: F10, F12, F14 Teoretically-Consistent Parameterization of a Multi-sector Global Model wit Heterogeneous Firms by Zeynep Akgul 1, Nelson Villoria, Tomas Hertel April 2015 Abstract Parameter selection in Computable General

More information

Design Optimization of a Hybrid Solar-Geothermal Power Plant

Design Optimization of a Hybrid Solar-Geothermal Power Plant Design Optimization of a Hybrid Solar- Power Plant Hybrid Solar Power plant Rafika Maali 1 *,Taar Kir 2, Ammar Ben Braim 1 1 Researc Unit Applied Termodynamic UR11ES8, Cemical Engeerg Processes /National

More information

Czochralski Crystal Growth

Czochralski Crystal Growth Czochralski Crystal Growth Crystal Pulling Crystal Ingots Shaping and Polishing 300 mm wafer 1 2 Advantage of larger diameter wafers Wafer area larger Chip area larger 3 4 Large-Diameter Wafer Handling

More information