HT 800 WP. The interchangeable insert drilling system GÜHRING - YOUR WORLD-WIDE PARTNER

Transcription

1 PRICELIST 42/2013 For extreme process reliability From ole diameter 11 to 40.0 For drilling depts 1.5xD, 3xD, 5xD, 7xD and 10xD Wit intercangeable inserts for steel, stainless steel, cast iron and Al Holders/intercangeable inserts for pilot drilling/countersinking Te intercangeable insert drilling system GÜHRING - YOUR WORLD-WIDE PARTNER

2 and power engineering Te ideal drilling system for te production of large, igly-accurate oles in a variety of materials for wind and water power stations, engine plants or gas/ steam turbines

3 - Overview INSERTS Tecnical features Application recoendations Notes regarding application Program and prices Page Page Page Page INSERT HOLDERS Tecnical features Selected macining results Program and prices Page Page Page ACCESSORIES Program and prices Page 30 GÜHRINGNAVIGATOR up to drilling dept 1 x D up to drilling dept 1.5 x D up to drilling dept 3 x D up to drilling dept 5 x D up to drilling dept 7 x D up to drilling dept 10 x D Page Page Page Page Page Page TROUBLESHOOTING Page 44 QUESTIONNAIRE SPECIAL TOOLS Page 47 3

4 - Tecnology and Advantages Wit te new intercangeable drilling system Guring provides ig-performance and cost-efficient olders for oles in te diameter range from to 40.0 tat excell tanks to te following advantages: A B C Extended tool life Tanks to special, micro-macined cutting edges and te application oriented surface finis te intercangeable inserts of te drilling system are especially wear resistant. Te olders of te drilling system also possess a very ig wear resistance. Tis is based on te optimised older material wit nickel plated surface as well as incremental older sizes in steps of 0.5 up to diameter and in steps of 1.0 above diameter Tis leads to less wear on te older body. Optimised cip flow Tanks to teir flute cross section te olders of te drilling system ensure optimal cip evacuation from te ole even wit larger drilling depts. Perfect cooling lubrication A perfect cooling lubrication is ensured by coolant ducts wit maximum cross section, exiting in te flute. Tereby enabling an optimal cooling lubrication of te cutting edges and additionally support te cip evacuation from te ole. D Higly accurate and rigid insert seat Te accurate insert seat enables te insert cange in te macine in only a few, simple steps wit a standard Torx screw driver. Tanks to te optimised material for te olders of te drilling system, te insert can be canged more frequently tan wit conventional systems before te older needs to be replaced due to wear of te insert seat. Te clamping screws wit screw lock ensure a secure olding of te intercangeable insert in te older even wit macines subject to ig levels of vibrations. Rigid olders Te close stepped diameter jumps wit te older sizes not only reduce wear. Troug te better guidance of te tool in te ole tey also increase te rigidity of te drilling system. Subsequently, resulting in longer tool life as well as improved workpiece surfaces. A D B C 4

5 - Application Tips Please observe te following notes and recoendations for te application of Guring s tools: We recoend wen canging te insert to also replace te clamping screw! Terefore, every older is supplied wit a clamping screw, Guring no. 4071, and screwdriver, Guring no Every intercangeable insert is also supplied wit a clamping screw, Guring no Wen canging te insert please observe te following tigtening torques for te clamping screw. Adering to tem is absolutely necessary for optimal macining results! Diameter range Tread M2.2 M2.5 M3 M3.5 M4 M4.5 M5 M6 Torx size T7 T8 T9 T10 T15 T15 T20 T25 Tigtening torque [Nm] Details apply to tread locking (Loctite)! Selected macining results Guring no Diameter Coating nanofire nanofire nanofire FIRE FIRE Material group alloyed eat-treatable steel alloyed eat-treatable steel general structural steels cast iron cast iron Material description 42CrMo4/ CrMo4/ St52-3/ GG25/ Drill. dept [] ,5 122, GGG40/ Hole type blind ole blind ole blind ole blind ole blind ole Cooling IC 40 bar IC 40 bar IC 40 bar IC 40 bar IC 55 bar Coolant soluble oil soluble oil soluble oil soluble oil soluble oil Macine type macining centre macining centre macining centre macining centre macining centre [] f z [] 0,28 0,25 0,15 0,30 0,60 Tool life [m]

6 Intercangeable Inserts intercangeable inserts are in respect of tool material, geometry and surface finis perfectly adapted to your specific range of application. Subsequently, you will always acieve optimal macining results wit maximum performance and igest economic efficiency. Te insert cange wit can be performed in te macine problem-free, te intercangeable insert always sits perfectly clamped and positioned in te older. From diameter up to regrinding of inserts is possible. Tecnical features and application recoendations optimal suitability limited suitability Guring no Tool material solid carbide solid carbide solid carbide solid carbide solid carbide Surface nanofire TiAlN nanoa FIRE brigt TiAlN nanoa Point geometry 2-facet relieved cone 2-facet relieved cone 2-facet Point angle Tolerance 7 7 m7 7 m7 Diameter Application steel stainl. steel cast iron aluminium pilot drilling Application group P M K N S H Material examples steel, cast steel, stainless steel (ferritic and martensitic) stainless steel and cast steel (austenitic and austenitic/ferritic) grey cast iron, speroidal grapite and malleable cast iron aluminium and oter non-ferrous metals Special, Super- and Ti-alloys Hardened steels and cilled cast iron Complete compatibility Te new intercangeable inserts as well as te new olders of te system are fully compatible wit te conventional intercangeable inserts and olders. You can, terefore, apply te new intercangeable inserts in te already existing olders or combine new olders wit existing intercangeable inserts. Drilling tests wit bot combination possibilities ave sown tat te efficiency of eac package lies above te values of te old system. You will definitely benefit! Te pilot insert 4111 can be combined wit any older, if te application requires a 145º point angle. optimal suitability limited suitability Application group P M K N S H Material examples steel, cast steel, stainless steel (ferritic and martensitic) stainless steel and cast steel (austenitic and austenitic/ferritic) grey cast iron, speroidal grapite und malleable cast iron aluminium and oter non-ferrous metals Special, Super- and Ti-alloys Hardened steels and cilled cast iron Guring no Tool material solid carbide solid carbide solid carbide Surface TiN TiAlN brigt Type CPGT... R CPGW... CPGT... R Application steel cast iron aluminium 6

7 Intercangeable Insert Holders olders offer igest accuracy and rigidity. Te open flute togeter wit internal cooling guarantees an optimal cip evacuation particularly from deeper oles. Te reinforced sank to DIN 6535 HE ensures te strong and accurate clamping of te older in te tool older. As it meets te DIN standard for solid carbide monoblock tools, a problem-free cangeover to te system in production is possible at any time. Guring no Drilling dept 1 x D 1.5 x D 3 x D 5 x D 7 x D 10 x D Diameter Sank DIN 6535-HE DIN 6535-HE DIN 6535-HE DIN 6535-HE DIN 6535-HE DIN 6535-HE 45º pilot drilling/ countersinking Special tools In addition to our standard tools we also supply stepped tools as well as alternative coatings for intercangeable inserts as special solutions. Special sizes are available on request. Please note our questionnaire on page 47. 7

8 Intercangeable Inserts For Macining Steel Order no. = Guring no. + Code-no. d 1 l 4 Guring no DIN Guring std. Guring std. Guring std. Guring std. Tool material P M K N S H Surface finis nanofire TiAlN nanoa FIRE brigt Discount group Tolerance 7 7 m7 7 b for drill. older size for pilot older size inc d1 l4 b Availability Availability Availability Availability 11, , , , / , , , / , , , , / , , , / , , , , / , / , , , , , / , , , / , , , , / , , , , / , , , , / , , , , , / , , / , , / , , / , / , , , / Inserts are always supplied wit clamping screw, Guring no

9 Intercangeable Inserts For Macining Stainless Steel Order no. = Guring no. + Code-no. d 1 l 4 Guring no DIN Guring std. Guring std. Guring std. Guring std. Tool material P M K N S H Surface finis nanofire TiAlN nanoa FIRE brigt Discount group Tolerance 7 7 m7 7 b for drill. older size for pilot older size inc d1 l4 b Availability Availability Availability Availability 18, , / , , / , , / , , / , , , / , , / , , / , , / , , / , , / , , / , , / , , / , / , , / , , , / , , / , / , , , , , , , / , , / , , , , / , , / , , , Inserts are always supplied wit clamping screw, Guring no

10 Intercangeable Inserts For Macining Cast Iron Order no. = Guring no. + Code-no. d 1 l 4 Guring no DIN Guring std. Guring std. Guring std. Guring std. Tool material P M K N S H Surface finis nanofire TiAlN nanoa FIRE brigt Discount group Tolerance 7 7 m7 7 b for drill. older size for pilot older size inc d1 l4 b Availability Availability Availability Availability 29, / , , / , , / , , / , , , / , , , / , / , , / , , , / , , , , , / , , , / , , / , , , / , , / , , , Inserts are always supplied wit clamping screw, Guring no

11 Intercangeable Inserts For Macining Aluminium Order no. = Guring no. + Code-no. d 1 m7 l 4 Guring no 4111 DIN Tool material P M K N S H Surface finis Guring std. TiAlN nanoa Discount group 141 Tolerance m7 b for drill. older size for pilot older size inc d1 l4 b Availability 11, , , , / , , , / , , , , / , , , / , , , , / , / , , , , , / , , , / , , , , / , , , , / , , , , / , , , , , / , , / , , / , , / , / , , , / Inserts are always supplied wit clamping screw, Guring no

12 Intercangeable Inserts For Pilot Holes Order no. = Guring no. + Code-no. d 1 m7 l 4 Guring no 4111 DIN Tool material P M K N S H Surface finis Guring std. TiAlN nanoa Discount group 141 Tolerance m7 b for drill. older size for pilot older size inc d1 l4 b Availability 18, , / , , / , , / , / , , , / , , / , , / , , / , , / , , / , , / , , / , , / , / , , / , , , / , , / , , , , , , / , , / , , , , / , , , , , , / , , Inserts are always supplied wit clamping screw, Guring no

13 Intercangeable Inserts For Pilot Holes Order no. = Guring no. + Code-no. d 1 m7 l 4 Guring no 4111 DIN Tool material P M K N S H Surface finis Guring std. TiAlN nanoa Discount group 141 Tolerance m7 b for drill. older size for pilot older size inc d1 l4 b Availability 30, / , , , , , / , , , / , , / , , , / , , , , , , , , , , / , , , / , / , , , Inserts are always supplied wit clamping screw, Guring no

14 Countersink Inserts For Pilot and Countersink Holders Order no. = Guring no. + Code-no. d R 11 o Guring no DIN Tool material P M K N S H Surface finis Discount group 7645 Guring std. TiN o l s size for older size d s R l 52,040 CPGT050204R ,040 CPGT060204R ,080 CPGT09T308R Availability Order no. = Guring no. + Code-no. d R 11 o Guring no DIN Tool material P M K N S H Surface finis Discount group 7632 Guring std. TiAlN o l s size for older size d s R l 52,040 CPGW ,040 CPGW ,080 CPGW09T Availability Order no. = Guring no. + Code-no. d R 11 o Guring no DIN Tool material P M K N S H Surface finis Discount group 7635 Guring std. brigt o l s size for older size d s R l 52,040 CPGT050204R ,040 CPGT060204R ,080 CPGT09T308R Availability 14

15 Special Solutions stepped olders special clamping cucks inserts wit special coatings and geometries, e.g. radius inserts or inserts wit point angles 90 to 180

16 Intercangeable Insert Holders 1 x D For Pilot Drilling and Countersinking Guring no. Discount group Order no. = Guring no. + Code-no. d 3 2 x intercangeable 2 x Insert l 4 d 1 Nr. insert 4111 HT no l 2 45 o l 3 DIN straigt 6535-HE sank DIN 6535 HE d 2 6 l 1 *l1 wit pilot insert Guring no. 4111only. Wit drilling insert Guring no. 4112, 4113, 4114 or 4115, see and l4 dimensions page 8 to 10! Holder size d1 d26 d3 incl. WP l1* l2 max 11, , , , , , , , , , , , , , , , , , , , , , , , , , , , l3 Availability Holders are always supplied wit clamping screw, Guring no. 4071, and screwdriver, Guring no

17 Intercangeable Insert Holders 1.5 x D Guring no. Discount group Order no. = Guring no. + Code-no. d 1 l 4 d 3 l 2 l 3 DIN straigt 6535-HE sank DIN 6535 HE d 2 6 l 1 *l1 wit drilling insert Guring no. 4112, 4113, 4114 or 4115 only. Wit pilot insert Guring no. 4111, see and l4 dimensions page 11 to 13! Holder size d1 d26 d3 incl. WP l1* l2 max 11, , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , l3 Availability Holders are always supplied wit clamping screw, Guring no. 4071, and screwdriver, Guring no

18 Intercangeable Insert Holders 1.5 x D Guring no. Discount group Order no. = Guring no. + Code-no. d 1 l 4 d 3 l 2 l 3 DIN straigt 6535-HE sank DIN 6535 HE d 2 6 l 1 *l1 wit drilling insert Guring no. 4112, 4113, 4114 or 4115 only. Wit pilot insert Guring no. 4111, see and l4 dimensions page 11 to 13! Holder size d1 d26 d3 incl. WP l1* l2 max 23, , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , l3 Availability Holders are always supplied wit clamping screw, Guring no. 4071, and screwdriver, Guring no

19 Intercangeable Insert Holders 3 x D Guring no. Discount group Order no. = Guring no. + Code-no. l 4 d 3 straigt DIN 6535-HE sank DIN 6535 HE d 1 d 2 6 l 2 l 3 l 1 *l1 wit drilling insert Guring no. 4112, 4113, 4114 or 4115 only. Wit pilot insert Guring no. 4111, see and l4 dimensions page 11 to 13! Holder size d1 d26 d3 incl. WP l1* l2 max 11, , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , l3 Availability Holders are always supplied wit clamping screw, Guring no. 4071, and screwdriver, Guring no

20 Intercangeable Insert Holders 3 x D Guring no. Discount group Order no. = Guring no. + Code-no. l 4 d 1 d 3 straigt DIN 6535-HE sank DIN 6535 HE d 2 6 l 2 l 3 l 1 *l1 wit drilling insert Guring no. 4112, 4113, 4114 or 4115 only. Wit pilot insert Guring no. 4111, see and l4 dimensions page 11 to 13! Holder size d1 d26 d3 incl. WP l1* l2 max 21, , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , l3 Availability Holders are always supplied wit clamping screw, Guring no. 4071, and screwdriver, Guring no

21 Intercangeable Insert Holders 3 x D Guring no. Discount group Order no. = Guring no. + Code-no. l 4 d 3 straigt DIN 6535-HE sank DIN 6535 HE d 1 d 2 6 l 2 l 3 l 1 *l1 wit drilling insert Guring no. 4112, 4113, 4114 or 4115 only. Wit pilot insert Guring no. 4111, see and l4 dimensions page 11 to 13! Holder size d1 d26 d3 incl. WP l1* l2 max 32, , , , , , , , , , , , , , , , l3 Availability Holders are always supplied wit clamping screw, Guring no. 4071, and screwdriver, Guring no

22 Intercangeable Insert Holders 5 x D Guring no. Discount group Order no. = Guring no. + Code-no. l 4 d 3 Zylinderscaft straigt DIN 6535-HE 6535-HE sank DIN d 1 d 2 6 l 2 l 3 l 1 *l1 wit drilling insert Guring no. 4112, 4113, 4114 or 4115 only. Wit pilot insert Guring no. 4111, see and l4 dimensions page 11 to 13! Holder size d1 d26 d3 incl. WP l1* l2 max 11, , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , l3 Availability Holders are always supplied wit clamping screw, Guring no. 4071, and screwdriver, Guring no

23 Intercangeable Insert Holders 5 x D Guring no. Discount group Order no. = Guring no. + Code-no. l 4 d 3 straigt Zylinderscaft DIN 6535-HE sank DIN DIN HE HE d 1 d 2 6 l 2 l 3 l 1 *l1 wit drilling insert Guring no. 4112, 4113, 4114 or 4115 only. Wit pilot insert Guring no. 4111, see and l4 dimensions page 11 to 13! Holder size d1 d26 d3 incl. WP l1* l2 max 21, , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , l3 Availability Holders are always supplied wit clamping screw, Guring no. 4071, and screwdriver, Guring no

24 Intercangeable Insert Holders 5 x D Guring no. Discount group Order no. = Guring no. + Code-no. l 4 d 3 Zylinderscaft straigt DIN 6535-HE 6535-HE sank DIN d 1 d 2 6 l 2 l 3 l 1 *l1 wit drilling insert Guring no. 4112, 4113, 4114 or 4115 only. Wit pilot insert Guring no. 4111, see and l4 dimensions page 11 to 13! Holder size d1 d26 32, , , , , , , , , , , , , , , , d3 incl. WP l1* l2 max l3 Availability Holders are always supplied wit clamping screw, Guring no. 4071, and screwdriver, Guring no

25 Intercangeable Insert Holders 7 x D Guring no. Discount group Order no. = Guring no. + Code-no. l 4 d 3 straigt Zylinderscaft DIN 6535-HE sank DIN 6535-HE d 1 d 2 6 l 2 l 3 l 1 *l1 wit drilling insert Guring no. 4112, 4113, 4114 or 4115 only. Wit pilot insert Guring no. 4111, see and l4 dimensions page 11 to 13! Holder size d1 d26 d3 incl. WP l1* l2 max 11, , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , l3 Availability Holders are always supplied wit clamping screw, Guring no. 4071, and screwdriver, Guring no

26 Intercangeable Insert olders 7 x D Guring no. Discount group Order no. = Guring no. + Code-no. l 4 d 3 Zylinderscaft straigt DIN 6535-HE sank DIN 6535-HE d 1 d 2 6 l 2 l 3 l 1 *l1 wit drilling insert Guring no. 4112, 4113, 4114 or 4115 only. Wit pilot insert Guring no. 4111, see and l4 dimensions page 11 to 13! Holder size d1 d26 d3 incl. WP l1* l2 max 21, , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , l3 Availability Holders are always supplied wit clamping screw, Guring no. 4071, and screwdriver, Guring no

27 Intercangeable Insert Holders 10 x D Guring no. Discount group Order no. = Guring no. + Code-no. l 4 d 3 straigt DIN Zylinderscaft 6535-HE sank DIN 6535-HE d 1 d 2 6 l 2 l 3 l 1 *l1 wit drilling insert Guring no. 4112, 4113, 4114 or 4115 only. Wit pilot insert Guring no. 4111, see and l4 dimensions page 11 to 13! Holder size d1 d26 d3 incl. WP l1* l2 max 11, , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , l3 Availability Holders are always supplied wit clamping screw, Guring no. 4071, and screwdriver, Guring no

28 Intercangeable Insert olders 10 x D Guring no. Discount group Order no. = Guring no. + Code-no. l 4 d 3 Zylinderscaft straigt DIN 6535-HE sank DIN DIN 6535-HE 6535 HE d 1 d 2 6 l 2 l 3 l 1 *l1 wit drilling insert Guring no. 4112, 4113, 4114 or 4115 only. Wit pilot insert Guring no. 4111, see and l4 dimensions page 11 to 13! Holder size d1 d26 d3 incl. WP l1* l2 max 20, , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , l3 Availability Holders are always supplied wit clamping screw, Guring no. 4071, and screwdriver, Guring no

29 Intercangeable Insert Holders 10 x D Guring no. Discount group Order no. = Guring no. + Code-no. l 4 d 3 straigt DIN Zylinderscaft 6535-HE sank DIN 6535-HE d 1 d 2 6 l 2 l 3 l 1 *l1 wit drilling insert Guring no. 4112, 4113, 4114 or 4115 only. Wit pilot insert Guring no. 4111, see and l4 dimensions page 11 to 13! Holder size d1 d26 d3 incl. WP l1* l2 max 29, , , , , , , , , , , , l3 Availability Holders are always supplied wit clamping screw, Guring no. 4071, and screwdriver, Guring no

30 Clamping screws Guring no. Order no. = Guring no. + Code-no. G Torx Discount group l 1 Holder size G l1 wit Torx 2, /115 M T7 2, /125 M T7 2, /135 M T8 3, /145 M T9 3, /155 M T9 3, M T10 4, M T15 4, M T15 5, M T20 5, M T20 5, M T20 6, M T25 6, M T25 6, M T25 Screwdriver Order no. = Guring no. + Code-no. Guring no Discount group 140 Holder size for Torx 6,000 Pilot older T6 7,000 Pilot older T7 7, T7 8, /135 T8 9, T9 10, T10 15,000 Pilot older T15 15, T15 20, T20 25, T25 Availability Cooling lubricant exit Steel 30

31 Clamping screws Guring no Order no. = Guring no. + Code-no. 60 o Torx G Discount group 122 l1 Holder size G l1 wit Torx 2, M T6 2, M T7 4, M T15 Availability Torque key Order no. = Guring no. + Code-no. Guring no Discount group 114 Type Drive l1 Torque Nm Availability 2,000 A 1/ ,000 A 1/ ,000 A 1/ Torx-Bits Order no. = Guring no. + Code-no. Guring no Discount group 140 for Torx Drive l1 Availability 7,000 T7 1/4 25 8,000 T8 1/4 25 9,000 T9 1/ ,000 T10 1/ ,000 T15 1/ ,000 T20 1/ ,001 T25 1/4 25 Cast iron Aluminium 31

32 Application Recoendations All data are approximate values. Te actually acievable cutting speeds and feed rates depend on te respective macining conditions. We recoend suitable drilling trials. # 4111Tol. m7 2/3 xd1 For selecting te optimal tool and te recoended cutting parameters for your application tere is also an electronic version of GüringNavigator available at www. guering.de # 4112/4113 # 4114/4115 ~0,01 for troug oles supporting lands must remain in permanent contact. don t apply drilling tool witout trial for interrupted cutting (grooves, transverse oles). For interrupted cutting (max. 0.2 x D) it is recoended to reduce te feed rate wenever possible. in contrast to conventional indexable inserts, HT 800 tools are also suitable for te drilling of stacked seets. on a late (stationary tool) it must be ensured tat te tool is accurately centred. pre-condition for optimal macining results is a sufficient cooling lubricant supply wit soluble or neat oil. te tool is only of limited suitability for dry macining or MQL. For MQL application we recoend te use of te conical MQL sank end as well as Guring MQL components. Please contact our Sales Management. Drill-Ø Material group Coon structural steels Free-cutting steels Unalloyed eat-treatable steels Alloyed eat-treatable steels Unalloyed case ardened steels Alloyed case ardened steels Nitriding steels Tool steels Hig speed steels Spring steels Stainless steels, sulpured austenitic martensitic Hardened steels Special alloys Cast iron Speroidal grapite iron and malleable cast iron Cilled cast iron Ti and Ti-alloys Aluminium and Al-alloys Al wrougt alloys Al cast alloys 10 % Si 24 % Si Magnesium alloys Copper, low-alloyed Brass, sort-cipping long-cipping Bronze, sort-cipping Bronze, long-cipping Duroplastics Termoplastics New cast materials GGV New cast materials ADI f (/rev.) Coolant: air neat oil soluble oil Material examples, new description (old description in brackets) Figures in bold = material no. to DIN EN S185(St33), P275N(StE285), P235GH(H1), P265GH(H2) E295 (St50-2), E360 (St70-2), P500NH (WStE500) SMnPb30 (9SMnPb28), SMn37 (9SMn36) S20 (45S20), (60S20), SPb20 (45SPb20) C22, C30E (Ck30) C45, C45E (Ck45) C60, C60E (Ck60) MnSi4, Cr2, Cr NiCr6, Cr4, CrMo (C10), C10E (Ck10) CrMo11, MnSi NiCr13, MnCr5, CrMo CrAl CrMoV9, CrAlNi C75W, Cr6, CrMoV X210Cr12, X42Cr13, WCr6, X45NiCrMo S , S 6-5-2, S Si7, Cr3, CrV4 (51CrV4) X12CrS13, X14CrMoS17, X6CrMoS17, X8CrNiS X5CrNi18-10 (V2A), X6CrNiTi18-10, X6CrNiMoTi (V4A) X20CrNi172 (X17CrNi16-2), X39CrMo17-1, X2CrMoTi18-2 Tensile strengt MPa (N/2) Nimonic, Inconel, Monel, Hastelloy EN-GJL-100 (GG10), EN-GJL-200 (GG20) EN-GJL-250 (GG25), EN-GJL-350 (GG35) EN-GJS (GGG50), EN-GJMW (GTW35) EN-GJS (GGG70), EN-GJMB (GTS70) Ti99,5, TiAl5Sn2,5, TiCu TiAl6Zr5, TiAl6V4, TiAl4Mo4Sn2,5, - TiAl8Mo1V Al99,5, AlMgSi1, AlMg AlMgSiPb, AlCuMg1, AlMg3Si, AlZnMgCu1, G-AlSi5Cu1, G-AlSi7Cu3, G-AlSi G-AlSi12, G-AlSi12Cu, - G-AlSi12CuNiMg MgMn2, G-MgAl8Zn1, G-MgAl6Zn SE-Cu, CuSn6, G-CuSn5ZnPb CuZn39Pb2, CuZn39Pb3, CuZn43Pb CuZn20, CuZn33, CuZn37Pb0, CuSn7ZnPb, CuPb5Sn5, CuPb10Sn CuNi18Zn19Pb CuAl5, CuAl9Mn, CuSn CuAl11Ni, CuBe2 Bakelit, Resopal, Pertinax, Moltopren Plexiglass, Hostalen, Novodur, Makralon EN-GJV250 (GGV25), EN-GJV350 (GGV35) EN-GJV400 (GGV40), EN-GJV500 (GGV50), SiMo 6 EN-GJS (ADI800), EN-GJS (ADI1000) EN-GJS (ADI1200), EN-GJS (ADI1400) 2000 Hardness 350 HB HRC 66 HRC 240 HB 350 HB 240 HB 350 HB 350 HB HB 300 HB Cool-ant

33 Tool olders 1 D, Guring no for pilot drilling/countersinking Guring no. Tool material Carbide grade Surface finis Application 4111 K/P TiAlN nanoa pilot drilling/countersinking 4112 K/P nanofire steel 4115 K/P TiAlN nanoa stainless steel 4113 K/P FIRE cast iron 4114 K brigt Al and Al-alloys

34 Application Recoendations All data are approximate values. Te actually acievable cutting speeds and feed rates depend on te respective macining conditions. We recoend suitable drilling trials. For selecting te optimal tool and te recoended cutting parameters for your application tere is also an electronic version of GüringNavigator available at www. guering.de for troug oles supporting lands must remain in permanent contact. don t apply drilling tool witout trial for interrupted cutting (grooves, transverse oles). For interrupted cutting (max. 0.2 x D) it is recoended to reduce te feed rate wenever possible. in contrast to conventional indexable inserts, HT 800 tools are also suitable for te drilling of stacked seets. on a late (stationary tool) it must be ensured tat te tool is accurately centred. pre-condition for optimal macining results is a sufficient cooling lubricant supply wit soluble or neat oil. te tool is only of limited suitability for dry macining or MQL. For MQL application we recoend te use of te conical MQL sank end as well as Guring MQL components. Please contact our Sales Management. Drill-Ø Material group Coon structural steels Free-cutting steels Unalloyed eat-treatable steels Alloyed eat-treatable steels Unalloyed case ardened steels Alloyed case ardened steels Nitriding steels Tool steels Hig speed steels Spring steels Stainless steels, sulpured austenitic martensitic Hardened steels Special alloys Cast iron Speroidal grapite iron and malleable cast iron Cilled cast iron Ti and Ti-alloys Aluminium and Al-alloys Al wrougt alloys Al cast alloys 10 % Si 24 % Si Magnesium alloys Copper, low-alloyed Brass, sort-cipping long-cipping Bronze, sort-cipping Bronze, long-cipping Duroplastics Termoplastics New cast materials GGV New cast materials ADI f (/rev.) Coolant: air neat oil soluble oil Material examples, new description (old description in brackets) Figures in bold = material no. to DIN EN S185(St33), P275N(StE285), P235GH(H1), P265GH(H2) E295 (St50-2), E360 (St70-2), P500NH (WStE500) SMnPb30 (9SMnPb28), SMn37 (9SMn36) S20 (45S20), (60S20), SPb20 (45SPb20) C22, C30E (Ck30) C45, C45E (Ck45) C60, C60E (Ck60) MnSi4, Cr2, Cr NiCr6, Cr4, CrMo (C10), C10E (Ck10) CrMo11, MnSi NiCr13, MnCr5, CrMo CrAl CrMoV9, CrAlNi C75W, Cr6, CrMoV X210Cr12, X42Cr13, WCr6, X45NiCrMo S , S 6-5-2, S Si7, Cr3, CrV4 (51CrV4) X12CrS13, X14CrMoS17, X6CrMoS17, X8CrNiS X5CrNi18-10 (V2A), X6CrNiTi18-10, X6CrNiMoTi (V4A) X20CrNi172 (X17CrNi16-2), X39CrMo17-1, X2CrMoTi18-2 Tensile strengt MPa (N/2) Nimonic, Inconel, Monel, Hastelloy EN-GJL-100 (GG10), EN-GJL-200 (GG20) EN-GJL-250 (GG25), EN-GJL-350 (GG35) EN-GJS (GGG50), EN-GJMW (GTW35) EN-GJS (GGG70), EN-GJMB (GTS70) Ti99,5, TiAl5Sn2,5, TiCu TiAl6Zr5, TiAl6V4, TiAl4Mo4Sn2,5, - TiAl8Mo1V Al99,5, AlMgSi1, AlMg AlMgSiPb, AlCuMg1, AlMg3Si, AlZnMgCu1, G-AlSi5Cu1, G-AlSi7Cu3, G-AlSi G-AlSi12, G-AlSi12Cu, - G-AlSi12CuNiMg MgMn2, G-MgAl8Zn1, G-MgAl6Zn SE-Cu, CuSn6, G-CuSn5ZnPb CuZn39Pb2, CuZn39Pb3, CuZn43Pb CuZn20, CuZn33, CuZn37Pb0, CuSn7ZnPb, CuPb5Sn5, CuPb10Sn CuNi18Zn19Pb CuAl5, CuAl9Mn, CuSn CuAl11Ni, CuBe2 Bakelit, Resopal, Pertinax, Moltopren Plexiglass, Hostalen, Novodur, Makralon EN-GJV250 (GGV25), EN-GJV350 (GGV35) EN-GJV400 (GGV40), EN-GJV500 (GGV50), SiMo 6 EN-GJS (ADI800), EN-GJS (ADI1000) EN-GJS (ADI1200), EN-GJS (ADI1400) 2000 Hardness 350 HB HRC 66 HRC 240 HB 350 HB 240 HB 350 HB 350 HB HB 300 HB Cool-ant

35 Tool olders 1.5 D, Guring no Guring no. Tool material Carbide grade Surface finis Application 4112 K/P nanofire steel 4115 K/P TiAlN nanoa stainless steel 4113 K/P FIRE cast iron 4114 K brigt Al and Al-alloys

36 Application Recoendations All data are approximate values. Te actually acievable cutting speeds and feed rates depend on te respective macining conditions. We recoend suitable drilling trials. For selecting te optimal tool and te recoended cutting parameters for your application tere is also an electronic version of GüringNavigator available at www. guering.de for troug oles supporting lands must remain in permanent contact. don t apply drilling tool witout trial for interrupted cutting (grooves, transverse oles). For interrupted cutting (max. 0.2 x D) it is recoended to reduce te feed rate wenever possible. in contrast to conventional indexable inserts, HT 800 tools are also suitable for te drilling of stacked seets. on a late (stationary tool) it must be ensured tat te tool is accurately centred. pre-condition for optimal macining results is a sufficient cooling lubricant supply wit soluble or neat oil. te tool is only of limited suitability for dry macining or MQL. For MQL application we recoend te use of te conical MQL sank end as well as Guring MQL components. Please contact our Sales Management. Drill-Ø , , ,250 Material group Coon structural steels Free-cutting steels Unalloyed eat-treatable steels Alloyed eat-treatable steels Unalloyed case ardened steels Alloyed case ardened steels Nitriding steels Tool steels Hig speed steels Spring steels Stainless steels, sulpured austenitic martensitic Hardened steels Special alloys Cast iron Speroidal grapite iron and malleable cast iron Cilled cast iron Ti and Ti-alloys Aluminium and Al-alloys Al wrougt alloys Al cast alloys 10 % Si 24 % Si Magnesium alloys Copper, low-alloyed Brass, sort-cipping long-cipping Bronze, sort-cipping Bronze, long-cipping Duroplastics Termoplastics New cast materials GGV New cast materials ADI ,315 f (/rev.) , , , , , ,630 Coolant: air neat oil soluble oil Material examples, new description (old description in brackets) Figures in bold = material no. to DIN EN S185(St33), P275N(StE285), P235GH(H1), P265GH(H2) E295 (St50-2), E360 (St70-2), P500NH (WStE500) SMnPb30 (9SMnPb28), SMn37 (9SMn36) S20 (45S20), (60S20), SPb20 (45SPb20) C22, C30E (Ck30) C45, C45E (Ck45) C60, C60E (Ck60) MnSi4, Cr2, Cr NiCr6, Cr4, CrMo (C10), C10E (Ck10) CrMo11, MnSi NiCr13, MnCr5, CrMo CrAl CrMoV9, CrAlNi C75W, Cr6, CrMoV X210Cr12, X42Cr13, WCr6, X45NiCrMo S , S 6-5-2, S Si7, Cr3, CrV4 (51CrV4) X12CrS13, X14CrMoS17, X6CrMoS17, X8CrNiS X5CrNi18-10 (V2A), X6CrNiTi18-10, X6CrNiMoTi (V4A) X20CrNi172 (X17CrNi16-2), X39CrMo17-1, X2CrMoTi18-2 Tensile strengt MPa (N/2) Nimonic, Inconel, Monel, Hastelloy EN-GJL-100 (GG10), EN-GJL-200 (GG20) EN-GJL-250 (GG25), EN-GJL-350 (GG35) EN-GJS (GGG50), EN-GJMW (GTW35) EN-GJS (GGG70), EN-GJMB (GTS70) Ti99,5, TiAl5Sn2,5, TiCu TiAl6Zr5, TiAl6V4, TiAl4Mo4Sn2,5, - TiAl8Mo1V Al99,5, AlMgSi1, AlMg AlMgSiPb, AlCuMg1, AlMg3Si, AlZnMgCu1, G-AlSi5Cu1, G-AlSi7Cu3, G-AlSi G-AlSi12, G-AlSi12Cu, - G-AlSi12CuNiMg MgMn2, G-MgAl8Zn1, G-MgAl6Zn SE-Cu, CuSn6, G-CuSn5ZnPb CuZn39Pb2, CuZn39Pb3, CuZn43Pb CuZn20, CuZn33, CuZn37Pb0, CuSn7ZnPb, CuPb5Sn5, CuPb10Sn CuNi18Zn19Pb CuAl5, CuAl9Mn, CuSn CuAl11Ni, CuBe2 Bakelit, Resopal, Pertinax, Moltopren Plexiglass, Hostalen, Novodur, Makralon EN-GJV250 (GGV25), EN-GJV350 (GGV35) EN-GJV400 (GGV40), EN-GJV500 (GGV50), SiMo 6 EN-GJS (ADI800), EN-GJS (ADI1000) EN-GJS (ADI1200), EN-GJS (ADI1400) 2000 Hardness 350 HB HRC 66 HRC 240 HB 350 HB 240 HB 350 HB 350 HB HB 300 HB Cool-ant

37 Tool olders 3 D, Guring no Guring no. Tool material Carbide grade Surface finis Application 4112 K/P nanofire steel 4115 K/P TiAlN nanoa stainless steel 4113 K/P FIRE cast iron 4114 K brigt Al and Al-alloys

38 Application Recoendations All data are approximate values. Te actually acievable cutting speeds and feed rates depend on te respective macining conditions. We recoend suitable drilling trials. For selecting te optimal tool and te recoended cutting parameters for your application tere is also an electronic version of GüringNavigator available at www. guering.de for troug oles supporting lands must remain in permanent contact. In addition, we recoend reducing te feed rate prior to exiting. for drilling depts from 5xD we generally recoend centring or pilot drilling wit older, Guring no. 4105, and pilot insert, Guring no Alternatively depending on te material to be macined Ratio drills type RT 100 U or RT 100VA can be applied. for drilling witout centring we recoend reducing te feed rate at te start of te ole. don t apply drilling tool witout trial for interrupted cutting (grooves, transverse oles). For interrupted cutting (max. 0.2 x D) it is recoended to reduce te feed rate wenever possible. in contrast to conventional indexable inserts, HT 800 tools are also suitable for te drilling of stacked seets. on a late (stationary tool) it must be ensured tat te tool is accurately centred. pre-condition for optimal macining results is a sufficient cooling lubricant supply wit soluble or neat oil. te tool is only of limited suitability for dry macining or MQL. For MQL application we recoend te use of te conical MQL sank end as well as Guring MQL components. Please contact our Sales Management. Drill-Ø Material group Coon structural steels Free-cutting steels Unalloyed eat-treatable steels Alloyed eat-treatable steels Unalloyed case ardened steels Alloyed case ardened steels Nitriding steels Tool steels Hig speed steels Spring steels Stainless steels, sulpured austenitic martensitic Hardened steels Special alloys Cast iron Speroidal grapite iron and malleable cast iron Cilled cast iron Ti and Ti-alloys Aluminium and Al-alloys Al wrougt alloys Al cast alloys 10 % Si 24 % Si Magnesium alloys Copper, low-alloyed Brass, sort-cipping long-cipping Bronze, sort-cipping Bronze, long-cipping Duroplastics Termoplastics New cast materials GGV New cast materials ADI f (/rev.) # 4111Tol. m7 2/3 xd1 # 4112/4113 # 4114/4115 ~0, Coolant: air neat oil soluble oil Material examples, new description (old description in brackets) Figures in bold = material no. to DIN EN S185(St33), P275N(StE285), P235GH(H1), P265GH(H2) E295 (St50-2), E360 (St70-2), P500NH (WStE500) SMnPb30 (9SMnPb28), SMn37 (9SMn36) S20 (45S20), (60S20), SPb20 (45SPb20) C22, C30E (Ck30) C45, C45E (Ck45) C60, C60E (Ck60) MnSi4, Cr2, Cr NiCr6, Cr4, CrMo (C10), C10E (Ck10) CrMo11, MnSi NiCr13, MnCr5, CrMo CrAl CrMoV9, CrAlNi C75W, Cr6, CrMoV X210Cr12, X42Cr13, WCr6, X45NiCrMo S , S 6-5-2, S Si7, Cr3, CrV4 (51CrV4) X12CrS13, X14CrMoS17, X6CrMoS17, X8CrNiS X5CrNi18-10 (V2A), X6CrNiTi18-10, X6CrNiMoTi (V4A) X20CrNi172 (X17CrNi16-2), X39CrMo17-1, X2CrMoTi18-2 Tensile strengt MPa (N/2) Nimonic, Inconel, Monel, Hastelloy EN-GJL-100 (GG10), EN-GJL-200 (GG20) EN-GJL-250 (GG25), EN-GJL-350 (GG35) EN-GJS (GGG50), EN-GJMW (GTW35) EN-GJS (GGG70), EN-GJMB (GTS70) Ti99,5, TiAl5Sn2,5, TiCu TiAl6Zr5, TiAl6V4, TiAl4Mo4Sn2,5, - TiAl8Mo1V Al99,5, AlMgSi1, AlMg AlMgSiPb, AlCuMg1, AlMg3Si, AlZnMgCu1, G-AlSi5Cu1, G-AlSi7Cu3, G-AlSi G-AlSi12, G-AlSi12Cu, - G-AlSi12CuNiMg MgMn2, G-MgAl8Zn1, G-MgAl6Zn SE-Cu, CuSn6, G-CuSn5ZnPb CuZn39Pb2, CuZn39Pb3, CuZn43Pb CuZn20, CuZn33, CuZn37Pb0, CuSn7ZnPb, CuPb5Sn5, CuPb10Sn CuNi18Zn19Pb CuAl5, CuAl9Mn, CuSn CuAl11Ni, CuBe2 Bakelit, Resopal, Pertinax, Moltopren Plexiglass, Hostalen, Novodur, Makralon EN-GJV250 (GGV25), EN-GJV350 (GGV35) EN-GJV400 (GGV40), EN-GJV500 (GGV50), SiMo 6 EN-GJS (ADI800), EN-GJS (ADI1000) EN-GJS (ADI1200), EN-GJS (ADI1400) 2000 Hardness 350 HB HRC 66 HRC 240 HB 350 HB 240 HB 350 HB 350 HB HB 300 HB Cool-ant

39 Tool olders 5 D, Guring no Guring no. Tool material Carbide grade Surface finis Application 4112 K/P nanofire steel 4115 K/P TiAlN nanoa stainless steel 4113 K/P FIRE cast iron 4114 K brigt Al and Al-alloys

40 Application Recoendations All data are approximate values. Te actually acievable cutting speeds and feed rates depend on te respective macining conditions. We recoend suitable drilling trials. For selecting te optimal tool and te recoended cutting parameters for your application tere is also an electronic version of GüringNavigator available at www. guering.de for troug oles supporting lands must remain in permanent contact. In addition, we recoend reducing te feed rate prior to exiting. for drilling depts from 5xD we generally recoend centring or pilot drilling wit older, Guring no. 4105, and pilot insert, Guring no Alternatively depending on te material to be macined Ratio drills type RT 100 U or RT 100VA can be applied. for drilling witout centring we recoend reducing te feed rate at te start of te ole. don t apply drilling tool witout trial for interrupted cutting (grooves, transverse oles). For interrupted cutting (max. 0.2 x D) it is recoended to reduce te feed rate wenever possible. in contrast to conventional indexable inserts, HT 800 tools are also suitable for te drilling of stacked seets. on a late (stationary tool) it must be ensured tat te tool is accurately centred. pre-condition for optimal macining results is a sufficient cooling lubricant supply wit soluble or neat oil. te tool is only of limited suitability for dry macining or MQL. For MQL application we recoend te use of te conical MQL sank end as well as Guring MQL components. Please contact our Sales Management. Drill-Ø Material group Coon structural steels Free-cutting steels Unalloyed eat-treatable steels Alloyed eat-treatable steels Unalloyed case ardened steels Alloyed case ardened steels Nitriding steels Tool steels Hig speed steels Spring steels Stainless steels, sulpured austenitic martensitic Hardened steels Special alloys Cast iron Speroidal grapite iron and malleable cast iron Cilled cast iron Ti and Ti-alloys Aluminium and Al-alloys Al wrougt alloys Al cast alloys 10 % Si 24 % Si Magnesium alloys Copper, low-alloyed Brass, sort-cipping long-cipping Bronze, sort-cipping Bronze, long-cipping Duroplastics Termoplastics New cast materials GGV New cast materials ADI f (/rev.) # 4111Tol. m7 2/3 xd1 # 4112/4113 # 4114/4115 ~0, Coolant: air neat oil soluble oil Material examples, new description (old description in brackets) Figures in bold = material no. to DIN EN S185(St33), P275N(StE285), P235GH(H1), P265GH(H2) E295 (St50-2), E360 (St70-2), P500NH (WStE500) SMnPb30 (9SMnPb28), SMn37 (9SMn36) S20 (45S20), (60S20), SPb20 (45SPb20) C22, C30E (Ck30) C45, C45E (Ck45) C60, C60E (Ck60) MnSi4, Cr2, Cr NiCr6, Cr4, CrMo (C10), C10E (Ck10) CrMo11, MnSi NiCr13, MnCr5, CrMo CrAl CrMoV9, CrAlNi C75W, Cr6, CrMoV X210Cr12, X42Cr13, WCr6, X45NiCrMo S , S 6-5-2, S Si7, Cr3, CrV4 (51CrV4) X12CrS13, X14CrMoS17, X6CrMoS17, X8CrNiS X5CrNi18-10 (V2A), X6CrNiTi18-10, X6CrNiMoTi (V4A) X20CrNi172 (X17CrNi16-2), X39CrMo17-1, X2CrMoTi18-2 Tensile strengt MPa (N/2) Nimonic, Inconel, Monel, Hastelloy EN-GJL-100 (GG10), EN-GJL-200 (GG20) EN-GJL-250 (GG25), EN-GJL-350 (GG35) EN-GJS (GGG50), EN-GJMW (GTW35) EN-GJS (GGG70), EN-GJMB (GTS70) Ti99,5, TiAl5Sn2,5, TiCu TiAl6Zr5, TiAl6V4, TiAl4Mo4Sn2,5, - TiAl8Mo1V Al99,5, AlMgSi1, AlMg AlMgSiPb, AlCuMg1, AlMg3Si, AlZnMgCu1, G-AlSi5Cu1, G-AlSi7Cu3, G-AlSi G-AlSi12, G-AlSi12Cu, - G-AlSi12CuNiMg MgMn2, G-MgAl8Zn1, G-MgAl6Zn SE-Cu, CuSn6, G-CuSn5ZnPb CuZn39Pb2, CuZn39Pb3, CuZn43Pb CuZn20, CuZn33, CuZn37Pb0, CuSn7ZnPb, CuPb5Sn5, CuPb10Sn CuNi18Zn19Pb CuAl5, CuAl9Mn, CuSn CuAl11Ni, CuBe2 Bakelit, Resopal, Pertinax, Moltopren Plexiglass, Hostalen, Novodur, Makralon EN-GJV250 (GGV25), EN-GJV350 (GGV35) EN-GJV400 (GGV40), EN-GJV500 (GGV50), SiMo 6 EN-GJS (ADI800), EN-GJS (ADI1000) EN-GJS (ADI1200), EN-GJS (ADI1400) 2000 Hardness 350 HB HRC 66 HRC 240 HB 350 HB 240 HB 350 HB 350 HB HB 300 HB Cool-ant

41 Tool olders 7 D, Guring no Guring no. Tool material Carbide grade Surface finis Application 4112 K/P nanofire steel 4115 K/P TiAlN nanoa stainless steel 4113 K/P FIRE cast iron 4114 K brigt Al and Al-alloys

42 Application Recoendations All data are approximate values. Te actually acievable cutting speeds and feed rates depend on te respective macining conditions. We recoend suitable drilling trials. For selecting te optimal tool and te recoended cutting parameters for your application tere is also an electronic version of GüringNavigator available at www. guering.de for troug oles supporting lands must remain in permanent contact. In addition, we recoend reducing te feed rate prior to exiting. for drilling depts from 5xD we generally recoend centring or pilot drilling wit older, Guring no. 4105, and pilot insert, Guring no Alternatively depending on te material to be macined Ratio drills type RT 100 U or RT 100VA can be applied. for drilling witout centring we recoend reducing te feed rate at te start of te ole. don t apply drilling tool witout trial for interrupted cutting (grooves, transverse oles). For interrupted cutting (max. 0.2 x D) it is recoended to reduce te feed rate wenever possible. in contrast to conventional indexable inserts, HT 800 tools are also suitable for te drilling of stacked seets. on a late (stationary tool) it must be ensured tat te tool is accurately centred. pre-condition for optimal macining results is a sufficient cooling lubricant supply wit soluble or neat oil. te tool is only of limited suitability for dry macining or MQL. For MQL application we recoend te use of te conical MQL sank end as well as Guring MQL components. Please contact our Sales Management. Drill-Ø Material group Coon structural steels Free-cutting steels Unalloyed eat-treatable steels Alloyed eat-treatable steels Unalloyed case ardened steels Alloyed case ardened steels Nitriding steels Tool steels Hig speed steels Spring steels Stainless steels, sulpured austenitic martensitic Hardened steels Special alloys Cast iron Speroidal grapite iron and malleable cast iron Cilled cast iron Ti and Ti-alloys Aluminium and Al-alloys Al wrougt alloys Al cast alloys 10 % Si 24 % Si Magnesium alloys Copper, low-alloyed Brass, sort-cipping long-cipping Bronze, sort-cipping Bronze, long-cipping Duroplastics Termoplastics New cast materials GGV New cast materials ADI f (/rev.) # 4111Tol. m7 2/3 xd1 # 4112/4113 # 4114/4115 ~0, Coolant: air neat oil soluble oil Material examples, new description (old description in brackets) Figures in bold = material no. to DIN EN S185(St33), P275N(StE285), P235GH(H1), P265GH(H2) E295 (St50-2), E360 (St70-2), P500NH (WStE500) SMnPb30 (9SMnPb28), SMn37 (9SMn36) S20 (45S20), (60S20), SPb20 (45SPb20) C22, C30E (Ck30) C45, C45E (Ck45) C60, C60E (Ck60) MnSi4, Cr2, Cr NiCr6, Cr4, CrMo (C10), C10E (Ck10) CrMo11, MnSi NiCr13, MnCr5, CrMo CrAl CrMoV9, CrAlNi C75W, Cr6, CrMoV X210Cr12, X42Cr13, WCr6, X45NiCrMo S , S 6-5-2, S Si7, Cr3, CrV4 (51CrV4) X12CrS13, X14CrMoS17, X6CrMoS17, X8CrNiS X5CrNi18-10 (V2A), X6CrNiTi18-10, X6CrNiMoTi (V4A) X20CrNi172 (X17CrNi16-2), X39CrMo17-1, X2CrMoTi18-2 Tensile strengt MPa (N/2) Nimonic, Inconel, Monel, Hastelloy EN-GJL-100 (GG10), EN-GJL-200 (GG20) EN-GJL-250 (GG25), EN-GJL-350 (GG35) EN-GJS (GGG50), EN-GJMW (GTW35) EN-GJS (GGG70), EN-GJMB (GTS70) Ti99,5, TiAl5Sn2,5, TiCu TiAl6Zr5, TiAl6V4, TiAl4Mo4Sn2,5, - TiAl8Mo1V Al99,5, AlMgSi1, AlMg AlMgSiPb, AlCuMg1, AlMg3Si, AlZnMgCu1, G-AlSi5Cu1, G-AlSi7Cu3, G-AlSi G-AlSi12, G-AlSi12Cu, - G-AlSi12CuNiMg MgMn2, G-MgAl8Zn1, G-MgAl6Zn SE-Cu, CuSn6, G-CuSn5ZnPb CuZn39Pb2, CuZn39Pb3, CuZn43Pb CuZn20, CuZn33, CuZn37Pb0, CuSn7ZnPb, CuPb5Sn5, CuPb10Sn CuNi18Zn19Pb CuAl5, CuAl9Mn, CuSn CuAl11Ni, CuBe2 Bakelit, Resopal, Pertinax, Moltopren Plexiglass, Hostalen, Novodur, Makralon EN-GJV250 (GGV25), EN-GJV350 (GGV35) EN-GJV400 (GGV40), EN-GJV500 (GGV50), SiMo 6 EN-GJS (ADI800), EN-GJS (ADI1000) EN-GJS (ADI1200), EN-GJS (ADI1400) 2000 Hardness 350 HB HRC 66 HRC 240 HB 350 HB 240 HB 350 HB 350 HB HB 300 HB Cool-ant

43 Tool olders 10 D, Guring no Guring no. Tool material Carbide grade Surface finis Application 4112 K/P nanofire steel 4115 K/P TiAlN nanoa stainless steel 4113 K/P FIRE cast iron 4114 K brigt Al and Al-alloys

44 Troublesooting 12 tips to elp diagnose problems Problem Cause Remedy Cutting edge build up low cutting speed increase cutting speed excessive oning of cutting lip reduce cutting lip oning brigt finis cutting lip ave tool coated Crumbling of outer corners non rigid conditions, insufficient workpiece rigid clamping of workpiece clamping deviation from concentricity too large ceck and correct concentricity if possible interrupted cut reduce feed Heavy wear at flank cutting speed too ig reduce cutting speed feed too low increase feed clearance angle too small increase clearance angle Crumbling on cutting lips non rigid conditions, insufficient workpiece rigid clamping of workpiece clamping interrupted cut reduce feed max. wear values exceeded reduce tool cange intervals incorrect tool type apply suitable tool Land wear non rigid conditions, insufficient workpiece rigid clamping of workpiece clamping deviation from concentricity too large ceck and correct concentricity if possible back taper too small increase back taper incorrect coolant (oil), coolant too weak increase strengt of coolant or use neat oil Scoring on tool body non rigid conditions, insufficient workpiece rigid clamping of workpiece clamping deviation from concentricity too large ceck and correct concentricity if possible interrupted cut reduce feed abrasive workpiece material increase strengt of coolant or use neat oil 44

45 Troublesooting 12 tips to elp diagnose problems Problem Cause Remedy Heavy cisel edge wear cutting speed too low increase cutting speed feed too ig reduce feed excessive oning of cutting lip reduce cutting lip oning Crumbling at intersection, web tinning and cutting lip clearance angle too small increase clearance angle excessive oning of cutting lip reduce cutting lip oning incorrect tool type apply suitable tool Plastic deformation of outer corner cutting speed too ig reduce cutting speed insufficient coolant volume increase volume/pressure incorrect or no oning at corner correct oning Misalignment non rigid conditions, insufficient workpiece rigid clamping of workpiece clamping deviation from concentricity too large ceck and correct concentricity if possible spotting area transverse use milling cutter (2-fluted) for spotting cisel edge too large reduce cisel edge Heavy burring on breaktroug feed too ig reduce feed max. wear values exceeded reduce tool cange intervals excessive oning of cutting lip reduce cutting lip oning Unsatisfactory surface quality R a non rigid conditions, insufficient workpiece rigid clamping of workpiece clamping deviation from concentricity too large ceck and correct concentricity if possible insufficient coolant volume increase volume/pressure 45

46 Surface Refining Processes, Coatings For Intercangeable Inserts FIRE/nanoFIRE Coating colour: violet Tis TiAlN/TiN multilayer coating is applied to HSS and carbide drills. It offers outstanding wear resistance in drilling operations and ig eat resistance. Besides conventional wet applications tis coating is suitable for minimum lubrication and dry macining, often combined wit MolyGlide to optimise te running-in wear and improved resistance to galling. TiCN Coating colour: grey End mills and taps exposed to ig mecanical load are coated wit TiCN. Wit respect to te ig ardness and tougness of TiCN coating te tools offer good macining results operating wit interrupted cutting. TiAlN SuperA/nanoA Coating colour: grey-violet Te well establised A-coating as been developed at Guring. By optimising te structural, cemical and mecanical properties of te new Super-A coating an extremely ig ot ardness, very good oxidation resistance and excellent coating adesion ave been acieved. Tis coating is used exclusively on carbide cutting tools and is ideally suited for difficult to macine aerospace materials suc as titanium alloys, Inconel as well as macining ardened steel materials (>52 HRC) and HSC applications. TiN Coating colour: yellow-golden Te monolayer titanium nitride coating is standard for HSS and carbide tools. Used for drilling, tapping and milling operations. Neverteless, most applications is steel macining. TiAlN Coating colour: violet Te monolayer TiAlN coating is suited for abrasive operations wit carbide tools because of its ig ardness and cemical resistance, e.g. ard macining and ig speed cutting (HSC). brigt Due to teir basically good properties, ig speed steel and carbide tools are supplied witout being surface treated, i.e. in a brigt finis. Guring offers brigt tools in its standard range only as basic tools for a cost-efficient coating to customer specific requirements. 46

47 Special Tools Questionnaire Fax Number / Order Enquiry Contact for queries Name/customer no. if available New customer Order number Street/ouse no. Town/post code Telepone Fax Date Signature Quantity olders inserts Material to be macined Macining * * *please incl. separate drawing Flute spiral partly spiral straigt Dimensions For spiral- & straigt-fluted types tol. 7 m7 point angle of intercangeable insert d1= d 1 1st intercangeable insert 2nd intercangeable insert d2= d 2 d 3 d 4 drilling dept 1 1. camfer angle drilling dept 2 flute lengt 2. camfer angle sank lengt total lengt Sank form HA HE HSK, form size SK, size Internal cooling yes no Intercangeable insert coating FIRE TiAlN SuperA TiAlN TiCN TiN brigt 47

48 SPECIAL TOOLING SOLUTIONS TAPPING/THREAD MILLING/ FLUTELESS TAPPING MILLING COUNTERSINKING/ DE-BURRING MODULAR TOOLING SYSTEMS Güring KG P.O. Box D Albstadt Herderstr D Albstadt Telepone: Fax: No liability can be accepted for printing errors or tecnical canges of any kind. Our Conditions of Sale and Terms of Payment apply. Available on request. REAMING PCD TOOL RESTORATION SERVICE /1553-V-25 Printed in Germany 2015 DRILLING