DILLARD S TEST PROTOCOL FOR DILR US HAMPER (V7)

Transcription

1 Test Date: Reviewed By/Date: SCOPE: This protocol is applicable to hamper or laundry baskets. SUPPLEMENTAL PROTOCOLS * CA Prop 65 CPSD-AN-PTCL US DILLARD S TEST PROTOCOL FOR -- The sample should be reviewed against the requirements of California Proposition 65 to determine if additional testing or labeling is required. Note: Additional cost, sample size & TAT may be required if testing to 1 or more supplemental protocols is necessary. Please refer to the above referenced supplemental protocol(s) for additional information. LABELING One Time Use Products **Fair Packaging and Labeling Act OR All Other Products **Uniform Packaging and Labeling Regulations F.P. & L. Act (16 CFR 500) OR NIST Uniform Laws and Regulations Handbook Manufacturer, Packer, or Distributor s Name & Address (City, State & Zip) Product identification Net quantity of contents shall be expressed in terms of weight or mass, measure, numerical count, or combination so as to give accurate information to facilitate consumer comparison (U.S. and metric units). **Country of origin marking 19 CFR Shall indicate country of origin legibly, permanently, and in comparable size and close proximity to any mention of country other than country in which the article was manufactured or produced. Must be visible at point of purchase. Use labeling 1 Use / care instructions that are clear and understandable shall be provided in language appropriate to destination countries. Page 1 of 9

2 Claim verification - level 2 CPSD-GB All Examine the retail packaging (or submitted artwork). Record each objective (factual) claim which can be substantiated by the testing within the protocols and rate accordingly. ANALYTICAL *Total lead content in surface coatings AOAC (modified) / CPSD-AN Record testing that extend beyond existing net quantity / dimensional testing on this protocol. Record all other objective (factual) and subjective (opinion) claims as NT and rate as DATA. Record information evaluated between the graphic imagery and the product. Record disclaimers on datasheet. 1 All accessible surface coatings in the as received state on items outside of the scope of 16 CFR 1303 shall not contain lead or lead components in which the lead content is in excess of 0.009% (90ppm) of the weight of the total content. Report actual results or include data table within report. Component testing is allowed. Compositing up to 3 like materials is allowed. * Heavy metal in packaging-doc Model Toxics in Packaging Legislation of the Toxics in Packaging Clearinghouse (TPCH) / CPSD-GB FLAMMABILITY Solids - Flammability 16 CFR (c)(6)(vi) / 16 CFR Client Requirement 1 The sum of concentration levels of lead, cadmium, mercury and hexavalent chromium in packaging or packaging components shall not exceed 100 mg/kg (100 ppm) by weight. In lieu of testing, test report can be submitted if dated within One year. 1 Shall not exceed the maximum allowable limit of no greater than 0.1 inches per second. Page 2 of 9

3 PHYSICAL CHARACTERISTICS Dimensions Parts inventory Material type Warpage WORKMANSHIP CPSD-GB Sharp points and sharp edges 16 CFR / modified Defects Workmanship PERFORMANCE Actual use - functionality Resistance to corrosion ASTM B modified / CPSD-HL Report overall dimensions; shall meet label claims (if applicable). (-0/+5%) 1 Shall meet label claims. 1 Report actual; shall be as claimed. 1 Shall not rock appreciably on smooth surface and not show warpage (If Applicable) (Maximum offset: 1/32 in.) All All All All Shall have no sharp points / edges, other than those required for function. Modification = expanded scope to other products Shall have no discernible surface degradation, including crazing, shivering, denting, bubbles, cracks, stains, deformations, chips, fractures, heavy lines, waves, shear marks, scratches, scuff marks, indentations, or blisters. Shall have no components missing, malformed, and / or fractured. Shall function as intended as received. Testing is limited to verification of basic function. Only function failures will be reported. NT rating shall be given to product that cannot be tested due to testing cannot be replicated in laboratory conditions. 1 [Applicable to samples / sample components constructed of metal or samples with metallic coatings that can be exposed to the environment] Shall withstand 24 hours in 1% salt spray (fog) with no noticeable oxidation / corrosion / visual changes. Modification = 1% salt spray (fog). Page 3 of 9

4 Attachment strength CPSD-HL Functional: 15 lb for 10 seconds minimum Non-Functional: 8 lb for 10 seconds minimum Sequins, beads, bugles & rhinestones: 4 lb for 10 seconds minimum Note: tested by force gauge Tilt resistance Cycle test Humidity exposure Effects of extreme temperature change CPSD-HL CPSD-HL CPSD-HL * Ease of assembly CPSD-HL Operates safely Handle strength - loaded Pockets loading strength Loading capacity CPSD-HL Shall not tip over at 8 degree incline plane in the direction of least stability. 1 All movable parts shall have no damage after 100 cycles 1 Should withstand 24 hours at 100 F and 95%RH with no visual change hours at 0 F and 120 F - No failure. The sample shall not have any structural failure and visual changes such as cracks, fractures or significant aesthetic changes. 1 Shall be easy to follow with assembly, use, maintenance, and safety information as required with no errors or spelling mistakes. 1 5 cycles of use. Test fails if any part of operation is unsafe. 1 Shall not exhibit permanent structural deformation and or loosening of handle when lifted for 1 minute after being loaded with test load of lb/in³ (470 kg/m³) or load of 1 lb/in (as appropriate). 1 Shall withstand distributed loading of 25kg/m for 60 minutes. 1 No failure - Apply 1.5 times claimed load for the intended use or 50 lb per ft² of load area for one minute. Page 4 of 9

5 Distributed load capacity CPSD-HL (Mod) 1 No loss of serviceability when the sample s primary use surface and extendable surfaces are subjected to a distributed load as calculated per sample s primary use surface for 60 minutes. > 4 sq. ft. = 40 lb / sq. ft. < 4 sq. ft. = 30 lb / sq. ft. Hooks or peg loading 1 Shall withstand 10 lb loading for 1 minute with no failure. Test each one separately. Drop test CPSD-HL Leak resistance * Coating adhesion test ASTM D (Mod) / CPSD-HL Shall withstand 3 drops from 36 in to vinyl covered concrete without damage to product. 1 Shall be no leakage or seepage when filled with water up to 8 hours. 1 Plating / finish must stay affixed. Minimum class 3 Cut the sample using hatch-cut or X-cut method based on thickness. Apply 1 in permacel tape to grid and evaluate if plating/ finish is intact. Modification: Expand scope to include testing on curved surface and all kind of base materials. Mounting hardware 1 Shall withstand force (2 x product weight) in actual use condition. Tensile strength - seam ASTM D (mod) 1 Report average of tensile strength in lb/in. Modification: Test at seam Tensile strength at break ASTM D Report average of tensile strength in lbs/in for normal and parallel direction. Page 5 of 9

6 Surface scratching CPSD-HL Slide the sample 6 in. (± 1/4 in) forward, in the most unfavorable orientation to make the worst effect, at a rate of approximately 1 in/s and then repeat in reverse direction. Apply force as close to the base of the sample as possible to maintain contact between the sample base and the test surface during sliding. Repeat for a total of 3 cycles over the same area. 1 cycle include a 6 inch forward and backward movement. Shall not have scratching or gouging. Cleanability 1 Demonstrates good resistance to common household cleaners with no evidence of color loss or material degradation when exposed to one hour spot test. Stackability Protective caps on legs Cap removal strength - end of furniture legs Magnetic mounting Tip-over test CPSD-HL Shall be able to stack as per intended without tip over. Note: Stack 3 samples if not claimed. 1 Shall be non - marring 1 Shall not separate. Minimum holding force of 2.0 lb. 1 Shall not exhibit loosening or slipping when applied to metallic surface as per intended for 3 days after being loaded with 2 times the volume capacity weight. 1 No damage, loosening or malfunction of product and its components when product is tipped over onto vinyl clad concrete floor surface. Page 6 of 9

7 * Caster or roller performance 1 Maximum horizontal force is applied to move the sample (with load placed on the product) on smooth vinyl surface for a maximum of 10 seconds. No measurement is taken for the first 5 seconds of the test. The caster shall be oriented in a running direction throughout the test Standard furniture: 5 lb horizontal force under 200 lbs load Small furniture: 3 lb horizontal force under 50 lbs load Note: Standard furniture, such as cabinets, trunks, table. Small furniture, such, plant stand, magazine rack, furniture that is not expected to support human weight * Strength tests for zippers ASTM D R [Chain crosswise strength] 50 lb minimum [Bottom stop] 20 lb minimum [Scoop pull] 10 lb minimum [Slider pull] 5 lb minimum [Slider torque] 2 in-lb minimum [Top stop] 20 lb minimum * Operability of zippers ASTM D R Maximum 5 lbs Seam strength ASTM D e1 (Mod) 1 Side seam: 25 lb. minimum Bottom seam: 25 lb. minimum Zipper seam: 25 lb. minimum Handle strength: 25 lb.minimum at 45 degree Reinforced stress points:25 lb.minimum Modification: Expanded scope of products Page 7 of 9

8 * Dimensional changes of fabrics after home laundering AATCC Woven General fabrics: -3% -3% Stretch fabrics (with spandex): -4% -4% Growth: +1% maximum Knit Shrinkage: General fabrics: -5% -5% Stretch fabrics (with spandex): -6% -6% Growth: +3% maximum Breaking strength of textile fabrics: grab test ASTM D R lb minimum. * Appearance after care CPSD-SL [3HL/1DC] No distortion, defects, damaged components, excessive puckering; Pilling: Grade 4.0 minimum Color change: Grade 4.0 minimum Self-staining: Grade 4.5 minimum COLORFASTNESS * Colorfastness to crocking AATCC Dry: Grade 4.0 minimum Wet: Grade 3.0 minimum * Colorfastness to rotary crocking AATCC Dry: Grade 4.0 minimum Wet: Grade 3.0 minimum * Colorfastness to water AATCC Color change: Grade 4.0 minimum. Color staining: Grade 3.5 minimum. Self-staining: Grade 4.5 minimum. * Colorfastness to laundering: accelerated * Colorfastness to chlorine bleach: spot test AATCC Color change: Grade 4.0 minimum Staining: Grade 3.5 minimum Self-staining: Grade 4.5 minimum CPSD-SL Grade 4.0 minimum Page 8 of 9

9 * Colorfastness to non-chlorine CPSD-SL Grade 4.0 minimum bleach: spot test Key: * Additional Charge For This Test ** Mandatory Requirement Results Key: Rating Key: M Meets NM Does Not Meet Good Good NA Not Applicable NT Not Tested Fail Fail C Claimed R Recorded No. Of Required For Complete Testing: 4 No. Of (Fully Packed) Cartons For Transit Testing: 1 (Only Upon Dillard s Request) Creation Date: MARCH 23, 2016 No. Of Working Days For Complete Testing: 10 Editorial Revision Date: JANUARY 9, 2018 Pricing Review Date: Technical Review Date: Page 9 of 9