Construction Equipment. Heavy Excavator. Buckets. G Class / H Class / S Class / X Class

Transcription

1 Equipment Excavator G Class / H Class / S Class / X Class

2 DOOSAN EXCAVATOR BUCKETS Doosan has combined the strengths of both Doosan, a leading manufacturer of excavator machines a Geith, a leading manufacturer of excavator attachments to develop a new series of excavator buckets. The new series of buckets are based on designs that have been developed over 50 years through customer feedback a experience in all markets throughout the world. The series is comprised of 4 kis of bucket types which are Bucket, Bucket, Severe Mining Bucket, a Xtreme Mining Bucket. Doosan Bucket using the 6 Kis of Good REASONS One-stop shop One place for complete solutions : (carrier + Bucket + parts + service) Engineering approved Optimized for DOOSAN equipment high efficiency a performance, resulting in lower running a maintenance cost. Service Broad coverage via the DOOSAN service network, fully supported by DOOSAN product specialists. Quality Products manufactured to highest staas. Warranty Avoid compatibility issues a operating differences from using Non-approved Bucket. Plug & Play readiness Easy to install a operate. HEAVY EXCAVATOR BUCKET TOUR Bucket, which is also called H bucket, is the most commonly used bucket in the construction equipment market a is designed mainly for use in heavy construction but also used in low density mining a quarry application. Wrapper (Shell) Hinge Optimized reinforced construction for high strength a performance matched to the machine s power. Shape increases heel clearance a decreases wear rate. Lip Plate (Cutting Edge) Beveled edge for better penetration a 500BHN material for high abrasion resistance. Side Wear Plates Side plates meet up with bottom wear plates for seamless corner protection. Corner adapter Positioned uer cast corner to increase strength. Tooth (Tip) Designed with mechanical properties that maintain haness for long wear life in tough digging applications. Cast Corner high strength (400HB) wear resistant material used in grou engaging area. No bolt on parts required (removes risk of losing parts). Horizontal Bottom Wear Plates Protects bottom section a reinforces bucket for greater strength a rigidity. Designed for easily replacement during maintenance repair.

3 Bucket Bucket GENERAL CONSTRUCTION BUCKET, which is also called G bucket, is designed for digging a re-haling soft to medium materials e.g. materials with low wear characteristics such as top-soil, loam, coal. HEAVY CONSTRUCTION BUCKET, which is also called H bucket, is the most commonly used bucket in the construction equipment market a is designed mainly for use in heavy construction but also used in low density mining a quarry application. Job Application Recommeed applications such as: heavy construction, road works, grou clearing, trenching a loading. Job Application Recommeed applications such as: heavy construction, road works, grou clearing, trenching a loading. Earth Haling La al uction n High abrasion resistant steel High abrasion resistant steel 1 500BHN, High abrasion resistant steel 1 4 different models Improved side cutter design for penetration a Protection 47 different models TYPE TYPE Low tip radius for greater digging performance noving ments Haling Earth Haling La tons Models are available La Haling La Earth Optimized designed genuine Doosan GD tooth point for general Haling Earth tons Models Haling are available La La Inserted casting corner design for penetration Diamo folded section for greater structural strength construction Diamo folded section for greater structural strength Optimized designed genuine Doosan HD tooth point for penetration Overlapping plate for protecting Lip plate a increasing strength Overlapping plate for protecting Lip plate a increasing strength Quick Coupler Friely design. - Used HB400 grade material on Lip plate Quick Coupler Friely design. - Used HB grade material on Lip plate a wear parts Flat bottom shape for Multi-purpose such as damping, leveling - Used Thicker steel wear pad than previous generation model Optimized Shape for better penetration a heel clearance Optimized designed GD tooth point for general construction Deep profile for High capacity Y POOL

4 Severe Mining Bucket Xtreme Mining Bucket Diamo folded section Lip plate (cutting edge) a) 0% increase in strength by adapting Diamo shape High Abrasion Resistance material ( BHN) a increasing thickness of steel Common parts Structure improved by overlapping cutting edge a bottom b) Overlap of bottom section a folded section increases the section improved penetration by beveled shape. strength of bucket structure. XTREME MINING BUCKET, which is also called X bucket. The bucket is designed for use in high density mining a quarry application using high strength a high abrasion resistance materials. It can be used in the toughest of applications. SEVERE MINING BUCKET, which is also called S bucket. The bucket is designed for use in high density mining a quarry application using high strength a high abrasion resistance materials. It can be used in the toughest of applications. a Job Application Job Application Recommeed applications such as: gravel, ripped basalt, caliche, shot granite, high silica sa, sharp rock a other dense materials. b Recommeed applications such as: ripped basalt, caliche, shot granite, high silica sa, sharp rock a other dense materials. Bottom section G H, S, X bucket Flat bottom shape for Multi-purpose Deep profile for High capacity such as damping, leveling. eneral neral nstruction ction nstruction Earth Mining &&Mining Haling La High abrasion resistant steel Haling Haling Haling La La La La Earth - Weld on side cutter design for Protection a material management Overlapping plate for protecting Lip plate a increasing strength. Quick Coupler Friely design. Earth Earth 11 different models tons Models are available OptimizedTYPE designed genuine TYPE Doosan SD tooth point for strength Added more patches for durability a strength Diamo folded section for greater structural strength Haling Haling Haling La La La Added more patches TYPE for durability a strength TYPE - Weld on side cutter design for Protection a material management Diamo folded section for greater structural strength - Diamo folded section Wear plate for extra strength - Diamo folded section Wear plate for extra strength Overlapping plate for protecting Lip plate a increasing strength. - Wear pads a bottom section - Wear pads a bottom section Quick Coupler Friely design. - Muscle Pack Heels to increase durability a protect shell from wear Optimized Shape for better penetration a heel clearance - Used incredible Strength with lip plate using 500HBN Deep profile for High capacity - Used incredible Strength with lip plate using 500HBN Low tip radius for greater digging performance - Used higher Abrasion resistance using 400HBN Low tip radius for greater digging performance - Used higher Abrasion resistance using 400HBN genuine Doosan SD tooth point for strength Optimized designed Wear pads & straps Optimized wear pads positioning for enhancing wear resistance Added more patches by usage of bucket. Deep profile for High capacity 500BHN, High abrasion resistant steel 1 Optimized Shape for better penetration a heel clearance 1 different models tons Models are available tion rth th ments achments achments 1 Haling High abrasion resistant steel 500BHN, High abrasion resistant steel 1 Mining &&Mining Strength a digging performance improved by positioning uer side plate. Improved penetration by digging angle. 1 Earth Arrangement of side plate, lip plate a tooth point - Internal wear-strap kit using 400BHN Additional Wear parts designed for ease of replacement during bucket maintenance a protecting protect bucket structure from wear H 0 tons a below H 4 tons a above S X

5 Hydraulic Excavator Doosan GET Portfolio Designed a proven by the Doosan R&D Center Doosan UNIQUE GEt SYSTEM GD ( Duty) for G bucket Tooth Tooth Length Weight (kg) GD ( Duty) Tooth Key 5 ton ton ~17 ton ~5 ton ton ~8 ton ton Optimized design for Doosan s GP a the new bucket. Suitable for machines ranging from 14 to 70 tons. Recommeed for general construction a utility loading applications. Key Characteristics A B C 1. Increased life span Durability has been increased by 50% compared with the previous model by modifying its shape a mechanical properties. Robust design a high strength quality castings. Appropriate steel alloys ensure strength, toughness, a resistance to wear a corrosion. High abrasion resistant material for extra durability. (HD/SD) 50 ton A B C HD ( Duty) for H Bucket Tooth Tooth Length Weight (kg) 14~17 ton Designed to maintain a uniform wear pattern throughout entire lifespan Test start Length Current GD Tooth New HD Tooth 18~5 ton ton ~8 ton ton ton ton SD (Severe Duty) for S/X bucket Tooth Tooth Length Weight (kg) Highly suitable for grou leveling Better digging action due to application of grooves on both sides Ideal for clean-out-utility work Worn out Over 50% Last Longer Operating Hours 18~5 ton ton ~8 ton ton ton ton HD ( Duty) Tooth Optimized design for the bucket. Suitable for machines ranging from 14 to 70 tons. Recommeed for most applications SD (Severe Duty) Tooth Optimized design for the Severe Mining bucket a the Xtreme Mining bucket. Suitable for machines ranging to 70 tons. Current GD VS New HD UP 50 % GET Tooth Pin Locking Washer 5 ton ton ~17 ton ~5 ton A 0 ton A including excavating, trenching, loading a medium density quarries a mining. Recommeed for extremely tough quarries a mining application.. Better penetration performance Self-sharpening tooth - The new Hd/S tooth is sharpened as they wear due to their unique design for improved penetrative power Reduced digging force a enhanced penetration due to optimum 4~8 ton A body shape a angle in simulation 4 ton ton ton 8 K1051 K10589 Key Characteristics Key Characteristics. Excellent GET economics IC code: Tooth Interchangeability Code - Tooth can be interchangeable with same number Greater lifespan a durability means fewer replacements New tooth is interchangeable with the old type Low initial investment Center-convex a corn shape Thicker front-e a great work volume Self-sharpening design, minimal unnecessary contact with materials Higher center-convex a roued shape Thickest front-e for maximum lifespan during rock abrasion Self-sharpening design delivers better penetration throughout entire product lifespan

6 Doosan Bucket Portfolio Doosan Bucket Portfolio 5 ton 8 ton 14 ton 18 ton ton 0 ton 4 ton 4 ton 50 ton 70 ton G H S X (m /yd ) / / / / / / / / / / 0. 5 (m /yd ) / / / / / / / / / / / / / / ,05 / / ,000 / / ,15 / / ,100 / / ,00 / / ,00 / / / / / / / / ,06 / / ,050 / / ,107 / / ,100 / / ,5 / / ,00 / / ,011 / / / / ,060 / / / / ,119 / / ,050 / / ,050 / / ,45 / / ,00 / / ,00 / / ,94 / / ,50 / / ,50 / / ,6 / / ,450 / / ,468 / / ,500 / / ,600 / / ,19 / / ,050 / / ,40 / / ,00 / / ,00 / / ,550 / / ,400 / / ,400 / / ,760 / / ,600 / / ,410 / / ,00 / / (m /yd ) ,500 / / ,500 / / ,505 / / ,50 / / ,50 / / ,50 / / ,680 / / ,450 / / ,450 / / ,450 / / ,600 / / ,600 / / ,800 / / ,800 / / ,00 / / ,49 / / ,50 / / ,50 / / ,50 / / ,667 / / ,500 / / ,500 / / ,700 / / ,00 / / ,587 / / ,50 / 5.07 / ,50 / / ,50 / / ,746 / / ,500 / 59.5 / ,500 / / ,500 / / ,700 / 67.7 / ,700 / / ,700 / / ,04 / / ,800 / / ,800 / / ,800 / / ,000 / 79.8 / ,000 / / ,500 / / ,700 / / ,800 / / (m /yd ) ,600 / / ,600 / / ,700 / / ,700 / / ,700 / / ,100 / / ,900 / / ,900 / / ,900 / / ,100 / / ,100 / / ,100 / /

7 Bucket Hydraulic Fixed Pulverizer Rotating Crusher Multi-processor STEEL SHEAR Multi- Stone Breaker Wood Log Orange Hydraulic Quick Coupler Clamshell Bucket Plate Compactor Pile Driver Ripper Vibrating Ripper Norway (Elnesvågen) Irela (Slane) Czech Republic (Dobris) France (Saint Priest) (Shaong) (Suzhou) (Yantai) Korea (Incheon & Gunsan) (Shanghai) USA (Gwinner) USA (Statesville) Brazil (São Paulo) Doosan worldwide factories Equipment Factory Compact Equipment Factory Attachment Factory Doosan Infracore Korea Office (HQ) 7/F, 75, Jangchungdan-ro, Jung-gu, Seoul, Korea Tel : ILDESIGN_EN_0150