Preliminary PO-SS0335BCZ-181

Transcription

1 Preliminary PO-SS0335BCZ-181 DATA SHEET QC: ENG: Prepared By: Part No. PO-0335 Series Page 1 OF 12

2 SPECIFICATIONS OF RED POWER SIDE VIEW TYPE BLUE SMD LED MODEL : SS0335BCZ FEATURES Side view type Blue SMD LED Low Drive Current,Recommend IF=20mA Instant Light Less Than 100ns Turn On Time Low Forward Voltage High Efficiency ESD Protection Pb- Free 2. APPLICATIONS Backlight Mobile phones Indicators ----/--/-- REV.1.0 Part No. PO-0335 Series Page 2 OF 12

3 3. SPECIFICATIONS (1) Absolute Maximum Ratings (Ta=25 ) Parameter Symbol MAX. Unit Continuous Forward Current If 20 ma Pulse Forward Current* Ifp 100 ma Reverse Voltage Vr 5 V Power Consumption Pc 75 mw Operating Temperature Range Topr -30 ~ +85 Storage Temperature Range Tstg -40 ~ +100 Electrostatic Discharge ESD 1000 V Soldering Temperature *Duty 1KHZ Tsld Reflow Soldering:240 /5sec Hand Soldering:350 /3sec (2) Electrical / Optical Characteristics (Ta=25 ) Parameter Symbol Min. Typ. Max Test Unit. Condition Forward Voltage* Vf 2.8 / 3.6 V If=20mA Luminous intensity* Iv / mcd If=20mA Peak Wavelength λp nm If=20mA Dominant Wavelength λd nm If=20mA Spectrum Radiation Bandwidth λ nm If=20mA Reverse Current Ir / / / Within Zener Diode Viewing Angle 2θ 1/2 / 120 / Deg * *Forward voltage measurement allowance is ±0.1V *2 1/2 is the off-axis angle at which the luminous intensity is half the axial luminous intensity. *Luminous intensity is measured with a light sensor and filter combination that approximates the CIE eye-response curve. *Luminous Intensity Measurement Allowance is ± 10%. Part No. PO-0335 Series Page 3 OF 12

4 (3). Product Naming Principle: Side View Type Single Die LeadFrame Type MODEL : PO- S S 0335 B C Z-XXX Color Emission (4). Bin Code Principle : Detail Divide Luminous Intensity Group BOM Serial With Zener Diode Resin Color Iv If= 20mA Group Bin Min. Max. Group Bin Min. Max O P Vf Group Color Rank Detail BIN CODE: O2 G K Detail Forward Voltage Group Vf If= 20mA Group Bin Min. Max. Group Bin Min. Max. Group Bin Min. Max. F G H I J Detail B COLOR Wavelength Group WLD If= 20mA Color Bin Min. Max. Bin Min. Max. Bin Min. Max. B I J K L M N Part No. PO-0335 Series Page 4 OF 12

5 RED POWER ( ) Typical Electrical / Optical Characteristics Curves Forward Currrent If(mA) Allowable Forward Currrent If(mA) Forward Current vs. Forward Voltage Forward Voltage VF(V) 4.2 Ambient Temperature vs. Allowable Forward Current Ambient Temperature Ta ( ) Allowable Forward Currrent IF(mA) Relative Luminous Intensity (%) Duty Ratio vs. Allowable Forward Current Duty Ratio (%) Ta= Luminous Intensity vs. Ambient Temperature Ambient Temperature Ta ( ) 1.0 Wavelength Distribution Relative Intensity Wavelength (nm) Part No. PO-0335 Series Page 5 OF 12

6 Relative Luminosity (a.u.) Ta=25 C If=20mA Beam Pattern 0 10 Radiation Angle Part No. PO-0335 Series Page 6 OF 12

7 4. Package 1. Outline Dimension (unit= mm) Cathode mark Polarity 1. All dimensions are in millmeters. 2. Tolerance are ±0.1 mm,unless otherwise noted. Part No. PO-0335 Series Page 7 OF 12

8 Part No. PO-0335 Series Page 8 OF Tapping Dimension (unit= mm) Polarity

9 3. Packing (unit= mm) 1 Anti-Static Reel in 1 Moistureproof Foil Bag. 3 Moistureproof Foil Bag in 1 Inner Box. ( Within Moisture Absorbent Material ) Package Label RED POWER CO., LTD MODEL : PO-SS0335BCZ-181 LOT NO : XXXXXXXXXX BIN CODE : S-B-E Iv (mcd) : XXX~XXX Vf (v) : X.X~X.X WL(nm) : XXX~XXX QTY : Inner Box in 1 Carton. Part No. PO-0335 Series Page 9 OF 12

10 5. Handling Precaution 1. Over-current use Applying proper resistor to the circuit design is recommended; otherwise slight voltage shift will cause big current change and the LEDs may be burned out. 2. Storage 2.1 Before opening the package: The LEDs should be kept at 30 & 90%RH. The LEDs should be used within a year. Moistureproof package with absorbent material (silica gel) is recommended. 2.2 After unpacking The LEDs should be kept at 30 & 70%RH. The LEDs should be used within 168 hours (7days) after opening the moistureproof package. If unused LEDs remain, they should be stored in moistureproof packages, such as sealed containers with moistureproof package within absorbent material (silica gel).it is also recommneded to return the unused LEDs to the original moistureproof package and to seal the moistureproof package again. If the moisture absorbent material (silica gel) vapors or expires the expiration date, baking treatment should be performed by using the following conditions. baking treatment : 60 for 24 hours. The LEDs electrode and leadframe comprise a silver plated copper alloy. The silver surface may be affected by environments. Please avoid conditions which may cause the LEDs being corroded or discolored. The corrosion or discoloration might lower solderability or affect optical characteristics. Please avoid rapid transition in ambient temperature, especially in high humidity environments where condensation can occur. 3. Static electricity The products are sensitive to static electricity and highly taken care when handling them. Static electricity or surge voltage will damage the LEDs. It is recommended to wear an anti-electrostatic wristband or an anti-electrostatic gloves when handling the LEDs. All devices, equipments and machinery must be properly grounded. It is recommended that measures be taken against surge voltage to the equipment that mounts the LEDs. Part No. PO-0335 Series Page 10 OF 12

11 RED POWER 4. Recommended soldering conditions 4.1 Reflow solder temperature profile 4.2 Recommended Soldering pad design (unit= mm) 4.3 Soldering conditions Reflow soldering should not be done more than twice. When soldering, do not stress on LEDs during heating. After soldering, do not warp the circuit board. 5. Repairing Repair should not be done after the LEDs have been soldered. When repair is unavoidable, double-head soldering iron should be used. It should be confirmed beforehand whether the characteristics of the LEDs will be damaged by repair or not. 6. Cleaning It is recommended to use isopropyl alcohol as a solvent to clean the LEDs. When using other solvents, it should be confirmed beforehand whether the solvents will dissolve the package and the resin or not. Part No. PO-0335 Series Page 11 OF 12

12 6. Reliability No. Items Test Conditions Note Number of Damaged 1 Reflow Soldering +240 /10 sec 2 Times 2 Temperature Cycle -40 ~+25 ~ min.~5min.~30min 1OO Cycles 3 Thermal Shock 0 ~ min.(15sec.)5min. 2O Cycles 4 High Temperature/ High Humidity Storage +65 /85RH 1000 Hours 5 Low Temperature Storage Hours 6 Steady State Operating Life +25 / 20mA 1000 Hours 7 Steady State Operating Life of High Temperature +65 /14mA 1000 Hours 8 Steady State Operating Life of Low Temperature -30 /20mA 1000 Hours Part No. PO-0335 Series Page 12 OF 12