INF-114 INF-210 INFUSION EPOXY. Technical Data

Transcription

1 Viscosity (cp) Rev 2 / Feb 2014 Technical Data INF-114 INF-210 HANDLING PROPERTIES 85 F (29 C) 150g Pot Life ASTM D2471 minutes g Pot Life ASTM D2471 minutes Viscosity Mixed ASTM D2196 cp Viscosity (resin) ASTM D2196 cp 1433 Viscosity (hardener) ASTM D2196 cp 16 MIX RATIO Method COMBINED FEATURES Weight 3.65:1 Very low viscosity for rapid saturation of fiberglass, Kevlar and carbon fiber laminate with resin infusion and VARTM processes. Fast cure speed hardener provides approximately 75 to 90 minutes of working time at 77 F (25 C). A typical laminate will be gelled in 2 to 3 hours. This combination is formulated specifically for resin infusion and VARTM processes. Do not use in open mold applications. Room temperature cure properties suitable for many composite components and structures. T g as high as 197 F (92 C) with proper post cure providing excellent temperature stability and great part cosmetics. Cost effective, high performance epoxy formulation for synthetic composite manufacturing. Quality-control tinting is available at no extra charge; simply add "QC" after the product code on your order. Shelf life is 3 years for resin and 2 years for hardener when properly stored 3. Weight Range 3.92:1 3.56:1 Volume 3.00:1 Volume Range 3.23:1 2.94:1 DENSITY 100: : : : : :34.0 State Units 72 F (22 C) Cured lb/gal (g/cc) 9.53 (1.14) Resin lb/gal (g/cc) 9.49 (1.14) Hardener lb/gal (g/cc) 7.82 (0.94) VISCOSITY VS TEMPERATURE Temperature ( F)

2 INF-114~INF-210 MECHANICAL PROPERTIES Hardness ASTM D2240 Type D Compression Yield ASTM D695 psi (MPa) Tensile Strength ASTM D638 psi (MPa) Tensile Modulus ASTM D638 psi (GPa) Tensile Elongation ASTM D638 % Flexural Strength ASTM D790 psi (MPa) Flexural Modulus ASTM D790 psi (GPa) THERMAL PROPERTIES Tg DMA Peak Tan Delta ASTM E F ( C) Tg DMA Onset Storage Modulus ASTM E F ( C) Tg DSC Onset 1st Heat ASTM E1356 F ( C) Heat Deflection Temperature ASTM D648 F ( C) Tg DSC Ultimate ASTM E1356 F ( C) F (49 C) F (60 C) F (82 C) ,700 (101) 16,000 (110) 14,800 (102) 14,900 (103) 15,000 (103) 8,670 (60) 10,100 (70) 11,000 (76) 11,000 (76) 11,300 (78) 5.57E+5 (3.84) 5.2E+5 (3.59) 5.06E+05 (3.49) 4.96E+05 (3.42) 4.56E+05 (3.14) ,500 (93) 15,900 (110) 18,600 (128) 18,800 (130) 19,300 (133) 4.83E+5 (3.33) 5.28E+5 (3.64) 4.89E+05 (3.37) 4.90E+05 (3.38) 4.69E+05 (3.23) F (49 C) F (60 C) F (82 C) 165 (74) 167 (75) 191 (88) 204 (96) 217 (103) 148 (64) 146 (63) 166 (75) 182 (83) 197 (92) 141 (61) 142 (61) 168 (76) 176 (80) 185 (85) 134 (57) 136 (58) 153 (67) 164 (73) 175 (79) 185 (85)² 1 1 Hz, 3 C per minute. 2 Additional post cure may be required; contact Technical Department for details. 3 Store PRO-SET Epoxy resins and hardeners at room temperature in sealed containers until shortly before use. As with many highperformance epoxy resins, repeated exposure to low temperatures during storage may cause the resin to crystallize. If this occurs, warm the resin to 125 F and stir to dissolve crystals. Hardeners may form carbamation when exposed to CO 2 and moisture in the atmosphere for extended periods of time. Prevent carbamation by protecting hardeners from exposure until immediately prior to processing. Rev 2 / Feb 2014

3 Viscosity (cp) Rev 4 / Feb 2014 Technical Data INF-114 INF-211 HANDLING PROPERTIES 85 F (29 C) 150g Pot Life ASTM D2471 minutes g Pot Life ASTM D2471 minutes Viscosity Mixed ASTM D2196 cp Viscosity (resin) ASTM D2196 cp 1433 Viscosity (hardener) ASTM D2196 cp 14 MIX RATIO Method COMBINED FEATURES Weight 3.65:1 Very low viscosity for rapid saturation of fiberglass, Kevlar and carbon fiber laminate with resin infusion and VARTM processes. Medium cure speed hardener provides 3 to 4 hours working time at 77 F (25 C). A typical laminate will be gelled in 8 hours. This combination is formulated specifically for resin infusion and VARTM processes. Do not use in open mold applications. Room temperature cure properties suitable for many composite components and structures. Tg as high as 196 F (91 C) with proper post cure providing excellent temperature stability and great part cosmetics. Cost effective, high performance epoxy formulation for synthetic composite manufacturing. Quality-control tinting is available at no extra charge; simply add "QC" after the product code on your order. Shelf life is 3 years for resin and 2 years for hardener when properly stored 3. Weight Range 3.81:1 3.45:1 Volume 3.00:1 Volume Range 3.13:1 2.84:1 DENSITY State Units 72 F (22 C) Cured lb/gal (g/cc) 9.5 (1.14) Resin lb/gal (g/cc) 9.5 (1.14) Hardener lb/gal (g/cc) 7.8 (0.93) VISCOSITY VS TEMPERATURE : : : : : : Temperature ( F)

4 INF-114~INF-211 MECHANICAL PROPERTIES Hardness ASTM D2240 Type D Compression Yield ASTM D695 psi (MPa) Tensile Strength ASTM D638 psi (MPa) Tensile Modulus ASTM D638 psi (GPa) Tensile Elongation ASTM D638 % Flexural Strength ASTM D790 psi (MPa) Flexural Modulus ASTM D790 psi (GPa) THERMAL PROPERTIES Tg DMA Peak Tan Delta ASTM E F ( C) Tg DMA Onset Storage Modulus ASTM E F ( C) Tg DSC Onset 1st Heat ASTM E1356 F ( C) Heat Deflection Temperature ASTM D648 F ( C) Tg DSC Ultimate ASTM E1356 F ( C) F (49 C) F (60 C) F (82 C) ,700 (101) 15,300 (105) 13,700 (94) 13,700 (94) 13,700 (94) 7,770 (54) 8,540 (59) 9,540 (66) 9,820 (68) 10,100 (70) 5.24E+5 (3.61) 5.34E+5 (3.68) 5.35E+05 (3.69) 5.11E+05 (3.52) 4.87E+05 (3.36) ,300 (85) 15,000 (103) 17,100 (118) 17,600 (121) 18,200 (125) 4.85E+5 (3.34) 4.83E+5 (3.33) 4.97E+05 (3.43) 4.95E+05 (3.41) 4.64E+05 (3.2) F (49 C) F (60 C) F (82 C) 158 (70) 157 (70) 176 (80) 195 (91) 215 (102) 145 (63) 145 (63) 157 (69) 176 (80) 196 (91) 138 (59) 138 (59) 151 (66) 165 (74) 177 (81) 129 (54) 131 (55) 144 (62) 160 (71) 173 (78) 185 (85)² 1 1 Hz, 3 C per minute. 2 Additional post cure may be required; contact Technical Department for details. 3 Store PRO-SET Epoxy resins and hardeners at room temperature in sealed containers until shortly before use. As with many high-performance epoxy resins, repeated exposure to low temperatures during storage may cause the resin to crystallize. If this occurs, warm the resin to 125 F and stir to dissolve crystals. Hardeners may form carbamation when exposed to CO 2 and moisture in the atmosphere for extended periods of time. Prevent carbamation by protecting hardeners from exposure until immediately prior to processing. Rev 4 / Feb 2014

5 Viscosity (cp) Rev 2 / Feb 2014 Technical Data INF-114 INF-213 COMBINED FEATURES Very low viscosity for rapid saturation of fiberglass, Kevlar and carbon fiber laminate with resin infusion and VARTM processes. Extra slow cure speed hardener provides up to 10 hours of working time at 77 F (25 C). A typical laminate will be gelled in approximately 14 to 18 hours at this temperature. This combination is formulated specifically for resin infusion and VARTM processes. Do not use in open mold applications. Room temperature cure properties suitable for many composite components and structures. T g as high as 193 F (89 C) with proper post cure providing excellent temperature stability and great part cosmetics. Cost effective, high performance epoxy formulation for synthetic composite manufacturing. Quality-control tinting is available at no extra charge; simply add "QC" after the product code on your order. Shelf life is 3 years for resin and 2 years for hardener when properly stored 3. HANDLING PROPERTIES 85 F (29 C) 150g Pot Life ASTM D2471 minutes g Pot Life ASTM D2471 minutes Viscosity Mixed ASTM D2196 cp Viscosity (resin) ASTM D2196 cp 1433 Viscosity (hardener) ASTM D2196 cp 13 MIX RATIO Method Weight 3.65:1 Weight Range 3.77:1 3.41:1 Volume 3.00:1 Volume Range 3.11:1 2.81:1 DENSITY State Units 72 F (22 C) Cured lb/gal (g/cc) 9.54 (1.14) Resin lb/gal (g/cc) 9.49 (1.14) Hardener lb/gal (g/cc) 7.82 (0.94) VISCOSITY VS TEMPERATURE : : : : : : Temperature ( F)

6 INF-114~INF-213 MECHANICAL PROPERTIES Hardness ASTM D2240 Type D Compression Yield ASTM D695 psi (MPa) Tensile Strength ASTM D638 psi (MPa) Tensile Modulus ASTM D638 psi (GPa) Tensile Elongation ASTM D638 % Flexural Strength ASTM D790 psi (MPa) Flexural Modulus ASTM D790 psi (GPa) THERMAL PROPERTIES Tg DMA Peak Tan Delta ASTM E F ( C) Tg DMA Onset Storage Modulus ASTM E F ( C) Tg DSC Onset 1st Heat ASTM E1356 F ( C) Heat Deflection Temperature ASTM D648 F ( C) Tg DSC Ultimate ASTM E1356 F ( C) F (49 C) F (60 C) F (82 C) ,000 (103) 15,100 (104) 14,000 (97) 14,000 (97) 14,000 (97) 7,900 (54) 8,410 (58) 9,600 (66) 9,800 (68) 10,100 (70) 5.4E+5 (3.72) 5.38E+5 (3.71) 4.95E+05 (3.41) 4.66E+05 (3.21) 4.99E+05 (3.44) ,900 (82) 13,000 (90) 16,100 (111) 16,200 (112) 16,300 (112) 4.74E+5 (3.27) 4.7E+5 (3.24) 4.86E+05 (3.35) 4.81E+05 (3.32) 4.56E+05 (3.14) F (49 C) F (60 C) F (82 C) 155 (68) 156 (69) 177 (81) 197 (92) 213 (100) 143 (62) 144 (62) 155 (68) 177 (81) 193 (89) 132 (56) 135 (57) 147 (64) 161 (72) 182 (83) 125 (52) 129 (54) 131 (55) 153 (67) 170 (77) 190 (88)² 1 1 Hz, 3 C per minute. 2 Additional post cure may be required; contact Technical Department for details. 3 Store PRO-SET Epoxy resins and hardeners at room temperature in sealed containers until shortly before use. As with many high-performance epoxy resins, repeated exposure to low temperatures during storage may cause the resin to crystallize. If this occurs, warm the resin to 125 F and stir to dissolve crystals. Hardeners may form carbamation when exposed to CO 2 and moisture in the atmosphere for extended periods of time. Prevent carbamation by protecting hardeners from exposure until immediately prior to processing. Rev 2 / Feb 2014

7 Viscosity (cp) Rev 5/ Dec Gougeon Brothers, Inc. Technical Data INF-114 INF-251-HT HIGH TEMPERATURE HANDLING PROPERTIES MIX RATIO COMBINED FEATURES Method Low viscosity for rapid saturation of fiberglass, Kevlar and carbon fiber laminate with resin infusion and VARTM processes. Extra slow cure speed hardener provides up to 12 hours of working time at 77 F (25 C). A typical laminate will be gelled in about 16 to 20 hours at this temperature. This combination is formulated specifically for resin infusion and VARTM processes. Do not use in open mold applications. Elevated temperature cure is required; thermal and mechanical properties suitable for composite components and hightemperature tooling and molds. T g as high as 277 F (136 C) with proper post cure providing excellent temperature stability and great part cosmetics. Cost effective, high performance epoxy formulation for synthetic composite manufacturing. Quality-control tinting is available at no extra charge; simply add "QC" after the product code on your order. Shelf life is 3 years for resin, 18 months for hardener when properly stored F (29 C) 150g Pot Life ASTM D2471 minutes g Pot Life ASTM D2471 minutes Viscosity Mixed ASTM D2196 cp Viscosity (resin) ASTM D2196 cp 1433 Viscosity (hardener) ASTM D2196 cp 121 Weight 3.65:1 Weight Range 3.72:1 3.31:1 Volume 3.00:1 Volume Range 3.08:1 2.74:1 DENSITY State Units 72 F (22 C) Cured lb/gal (g/cc) 9.42 (1.13) Resin lb/gal (g/cc) 9.49 (1.14) Hardener lb/gal (g/cc) 7.86 (0.94) VISCOSITY VS TEMPERATURE : : : : : : Temperature ( F)

8 INF-114~INF-251-HT HIGH TEMPERATURE MECHANICAL PROPERTIES Hardness ASTM D2240 Type D Compression Yield ASTM D695 psi (MPa) Tensile Strength ASTM D638 psi (MPa) Tensile Modulus ASTM D638 psi (GPa) Tensile Elongation ASTM D638 % Flexural Strength ASTM D790 psi (MPa) Flexural Modulus ASTM D790 psi (GPa) THERMAL PROPERTIES Tg DMA Peak Tan Delta ASTM E F ( C) Tg DMA Onset Storage Modulus ASTM E F ( C) Tg DSC Onset 1st Heat ASTM E1356 F ( C) Heat Deflection Temperature ASTM D648 F ( C) Tg DSC Ultimate ASTM E1356 F ( C) 140 F (60 C) ,600 (114) 16,100 (111) 8,280 (57) 9,200 (63) 4.94E+5 (3.41) 4.32E+5 (2.98) ,600 (121) 16,500 (114) 4.91E+5 (3.39) 4.E+5 (2.76) 140 F (60 C) 250 F (121 C) 250 F (121 C) 218 (103) 300 (149) 187 (86) 277 (136) 172 (78) 251 (122) 171 (77) 254 (123) 264 (129)² 1 1 Hz, 3 C per minute. 2 Additional post cure may be required; contact Technical Department for details. 3 Store PRO-SET Epoxy resins and hardeners at room temperature in sealed containers until shortly before use. As with many highperformance epoxy resins, repeated exposure to low temperatures during storage may cause the resin to crystallize. If this occurs, warm the resin to 125 F and stir to dissolve crystals. Hardeners may form carbamation when exposed to CO 2 and moisture in the atmosphere for extended periods of time. Prevent carbamation by protecting hardeners from exposure until immediately prior to processing. Rev 5/ Dec Gougeon Brothers, Inc.