JN FPC P CONNECTOR MANUFACTURER SIGNATURE

Transcription

1 DOC. NO.: - ISSUE DATE: 20 / / CUSTOMER: PART NAME: PART NO.: FPC P CONNECTOR 1 APP. DATE: MANUFACTURER SIGNATURE P-TWO INDUSTRIES INC. NO. 9, SHIN HWA RD, KWEI SHAN IND. PARK TAOYUAN, 330 TAIWAN, R.O.C. TEL: FAX: P-TWO INDUSTRIES(S.Z.) CO.LTD. NO.1,GONG YE NORTH ROAD,CO-PROSPERITY, INDUSTRIAL PARK, SONGGANG TOWN, BAOAN DISTRICT, SHENZHEN CITY, GUANGDONG, CHINA TEL: FAX: P-TWO TECHNOLOGY CO.,LTD. NO HUASHAN RD.FENG QIAO INDUSTRIAL PARK OF SUZHOU NEW DISTRICT,JIANGSU,CHINA TEL: FAX:

2 HISTORY REVISION Rev Date Page Reason for revision. ISS. A Add Initial Release. Chiwen 3 of 19 1 Modify the item 5.3(Terminal / Housing Chiwen A Retention Force) test value 150gf min. B of of 19 1 Replace the supplier of copper material. 2 Drawing version adjusted to B version. Chiwen 3 of 19 1 Modify the item 5.3(Terminal / Housing B of of of 19 B of of 19 B of 19 Home Page Retention Force) test value 200gf min. 2 Replace the UL card (actuator). 3 Replace the supplier material certificate. 1 Replace the UL card (Housing Actuator). 2 Replace the supplier of copper material. 3 Update pin weight indicator. 1 Update pin weight indicator. 2 Add history form Chiwen Chiwen Chiwen B of 19 1 Housing material quality change is E481i Kuan C of 23 1 Drawing version adjusted to C version. Allen of 17 5 of Add 6.1 Durability (FPC/FFC T=0.30mm) 2. Delete 7.1 H 2 S Gas & 7.2 NH 3 Gas Zoe

3 TABLE OF CONTENT I. SPECIFICATION OF PRODUCT II. III. IV. ORDERING INFORMATION MATERIAL REFERENCE TABLE PLASTIC MATERIAL CERTIFICATE OF HOUSING V. PLASTIC MATERIAL CERTIFICATE OF ACTUATOR VI. METAL MATERIAL CERTIFICATE OF TERMINAL VII. METAL MATERIAL CERTIFICATE OF FITTING NAIL VIII. THE CONFIRMATION OF PROHIBITED/CONTROLLED SUBSTANCES 1 of 17

4 SPECIFICATION OF PRODUCTS 1.0mm PITCH FFC/FPC CONNECTOR 1. Scope : This specification covers the requirements for product performance, and test methods provisions of 1.0mm PITCH FFC/FPC CONNECTOR. 2. Applicable documents : The following documents form a part of this specification to the extent specified herein. In the event of conflict between the requirements of this specification and the product drawing, the product drawing shall take precedence. In the event of conflict between the requirements of this specification and the referenced documents, this specification shall take precedence. 2.1 Military Standard and Specifications : MIL-STD-1344 Test Methods for Electrical Component Parts. MIL-STD-202 Test Methods for Electronic and Electrical Component Parts. 3. Requirements : 3.1 Designs and Construction : Product shall be of the design, construction and physical dimensions specified in the applicable product drawing. 3.2 Materials : A. Terminal : Copper Alloy. Matte Tin Plating (Lead Free). B. Fitting Nail : Copper Alloy. Matte Tin Plating (Lead Free). C. Housing : Heat Resistance Plastic (UL94 V-0). D. Actuator : Heat Resistance Plastic (UL94 V-0). 3.3 General Specification : A. Voltage Rating : 50V (AC/DC)/Contact. B. Current Rating : 0.5A (AC/DC)/Contact. C. Operation Temperature & Humidity Rating : -40 ~+85, 95%MAX. D. Storage Temperature & Humidity Rating : -40 ~+85, 95%MAX. 3.4 GP requires substances (level1) forbidden (including orders placed to subcontractors) 2 of 17

5 4. Electrical Performance : SPECIFICATION OF PRODUCTS No. Items Requirements Test Procedures 4.1 Contact Resistance Initial 20 m, After test 40 m MAX. It should be tested in accordance with method 3004of MIL-SDT-1344A. Measure by low level.(max:20mv,100ma) 4.2 Insulation Resistance 500 M MIN It should be tested in accordance with method 3003 of MIL-STD-1344A. When 500V DC is applied between adjacent contacts and insulation resistance is measured within one minute. 4.3 Dielectric Strength No Breakdown The connector shall be tested in accordance with method 3001of MIL-STD-1344A. When the 500V AC r.m.s for one minute applied between adjacent contacts. 5. Mechanical Performance : No. Items Requirements Test Procedures 5.1 Appearance Product shall be conforming to the requirements of applicable product drawing. Visually, dimensionally and functionally inspected per applicable product drawing. 5.2 FFC/FPC Retention Force 30gf / PIN MIN Insert the actuator, pull the FFC/FPC at the speed rate of 25 3 mm/minute. 5.3 Terminal / Housing Retention Force 50 gf MIN Apply axial pull out of force at the speed rate of 25 3 mm/minute on the terminal assembled in the housing. 5.4 Fitting Nail / Housing Retention Force 100 gf MIN Apply axial pull out of force at the speed rate of 25 3 mm/minute on the fitting nail assembled in the housing. 3 of 17

6 6. Physical Performance : SPECIFICATION OF PRODUCTS No. Items Requirements Test Procedures 6.1 Durability Appearance neither damage nor crack. Retention force 30gf / PIN MIN (FPC/FFC T=0.30mm) Contact Resistance 40m MAX Mate applicable FFC/FPC and insert and withdraw actuator at the speed rate of 25 3 mm/minute. Times Up to 30 cycles 6.2 Vibration 6.3 Shock 6.4 Solderability Appearance no damage,cracks,or parts dislocation. Contact Resistance 40m MAX Discontinuity 1μs MAX Appearance no damage,cracks,or parts dislocation. Contact Resistance 40m MAX Discontinuity 1μs MAX More than 95% of the immersion shall be covered with solder. In accordance with method MIL-STD-202 method 201, all contacts shall be connected in series and DC 100mA shall be applied. Wave form Sine wave Frequency 10~55~10Hz in 1 minutes Amplitude 1.5mm Orientation X,Y,Z (3 axes) Duration 2 hours /axis In accordance with method MIL-STD-202 method 213. DC 100mA shall be applied. MAX acceleration 50G Wave form Half sine wave Orientation X,Y,Z (3 axes) Duration 11ms./axis Times 3 strokes in each X,Y,Z axis It should be tested to compare with method 2 of MIL-STD-202. Steam Aging 8H Soldering time seconds Solder temperature Resistance to soldering heat No deformation of components affecting performance. 1. manual soldering Soldering time 5 seconds MAX Solder temperature Reflow Peak temperature Duration time seconds Condition 3 cycles 4 of 17

7 7. Environmental Performance : SPECIFICATION OF PRODUCTS No. Items Requirements Test Procedures 7.1 Salt spray Contact Resistance 40m MAX Humidity (steady state) Temperature cycling (Thermal Shock) Humidity, temperature cycling In accordance with method MIL-STD-202 method 101. Temperature 35 2 Density 5 1% in weight Duration 48 hours Appearance neither damage nor In accordance with method MIL-STD-202 crack. method 103. Contact Resistance 40 m MAX Temperature 40 2 Dielectric Strength No Breakdown Relative Humidity 90~95% Insulation Resistance 500 M MIN Duration 96 hours Contact Resistance 40m MAX In accordance with method MIL-STD-202 method 107. Temperature (30min) 25 3 (5min) 85 3 (30min) 25 3 (5min) Condition 25 cycles In accordance with method MIL-STD-202 method 106 (without low frequency Insulation Resistance 500M MIN. vibration). Subject mated connectors to 10 Contact Resistance 40m MAX. cycles 240h of humidity-temperature Dielectric Strength No Breakdown. change between -10 and 65 at 95% R.H. in a chamber. 7.5 Temperature life High (Heat Resistance) Contact Resistance 40m MAX. Appearance neither damage nor crack. In accordance with method MIL-STD-202 method 1. Temperature 85 2 Duration 96 hours 7.6 Temperature life Cold (Cold Resistance) Contact Resistance 40m MAX. Appearance neither damage nor crack. In accordance with method IEC Temperature Duration 96 hours 5 of 17

8 ORDERING INFORMATION 1.0mm PITCH FFC/FPC CONNECOTR Specifications: Part Name: 1.0mm PITCH FFC/FPC Connectors. Connector Styles: Wire to Board Connectors. ZIF (Zero Insertion Force) Type. Mounting of Connector On Board: SMT (Surface Mounted Technology) Type. Centerline (Pitch): 1.0mm(0.04 inch) Part No.: (1) (2) (3) (4) (5) (1) Type Of Connectors: 047:FPC 1.0P Swing Actuator Type (2) No. Of Contacts: 04~30Pin. (3) Plating: 02: Matte Tin Plating (Lead Free). (4) Packaging: 1: Tape & Reel. (5) Halogen-free 6 of 17

9 INFRARED REFLOW CONDITION Sn-Ag-Cu PROFILE Temperature Profile of Reflow Soldering 7 of 17

10 MATERIAL REFERENCE TABLE Parts Name General Name Model No. Heat Resistance Level UL Card NO. Specifie Weight Housing LCP E481i UL94 V-0 E Actuator LCP MG350BPRL UL94 V-0 E91944 Terminal Phosphor Bronze C5210R-SH See the Attachment (P10) Fitting Nail Brass C2680R-H 8 of 17

11 MATERIAL REFERENCE TABLE PIN Housing Actuator Terminal Fitting Nail Total to Weight gf 50.94% 0.019gf 17.92% 0.022gf 20.75% 0.011gf 10.38% 0.106gf gf 51.91% 0.024gf 18.32% 0.028gf 21.37% 0.011gf 8.40% 0.131gf 6 0.2gf 52.56% 0.029gf 18.59% 0.034gf 21.79% 0.011gf 7.05% 0.156gf gf 53.04% 0.034gf 18.78% 0.040gf 22.10% 0.011gf 6.% 0.181gf gf 53.40% 0.039gf 18.93% 0.046gf 22.33% 0.011gf 5.34% 0.206gf gf 53.68% 0.044gf 19.05% 0.052gf 22.51% 0.011gf 4.76% 0.231gf gf 53.91% 0.049gf 19.14% 0.058gf 22.66% 0.011gf 4.30% 0.256gf gf 54.09% 0.054gf 19.22% 0.064gf 22.78% 0.011gf 3.91% 0.281gf gf 54.25% 0.059gf 19.28% 0.070gf 22.88% 0.011gf 3.59% 0.306gf gf 54.38% 0.064gf 19.34% 0.076gf 22.96% 0.011gf 3.32% 0.331gf gf 54.49% 0.069gf 19.38% 0.2gf 23.03% 0.011gf 3.09% 0.356gf gf 54.59% 0.074gf 19.42% 0.8gf 23.10% 0.011gf 2.89% 0.381gf gf 54.68% 0.079gf 19.46% 0.094gf 23.15% 0.011gf 2.71% 0.406gf gf 54.76% 0.4gf 19.49% 0.100gf 23.20% 0.011gf 2.55% 0.431gf gf 54.82% 0.9gf 19.52% 0.106gf 23.25% 0.011gf 2.41% 0.456gf gf 54.89% 0.094gf 19.54% 0.112gf 23.28% 0.011gf 2.29% 0.481gf gf 54.94% 0.099gf 19.57% 0.118gf 23.32% 0.011gf 2.17% 0.506gf gf 54.99% 0.104gf 19.59% 0.124gf 23.35% 0.011gf 2.07% 0.531gf gf 55.04% 0.109gf 19.60% 0.130gf 23.38% 0.011gf 1.98% 0.556gf gf 55.% 0.114gf 19.62% 0.136gf 23.41% 0.011gf 1.89% 0.581gf gf 55.12% 0.119gf 19.64% 0.142gf 23.43% 0.011gf 1.82% 0.606gf gf 55.15% 0.124gf 19.65% 0.148gf 23.45% 0.011gf 1.74% 0.631gf gf 55.18% 0.129gf 19.66% 0.154gf 23.48% 0.011gf 1.68% 0.656gf gf 55.21% 0.134gf 19.68% 0.160gf 23.49% 0.011gf 1.62% 0.681gf gf 55.24% 0.139gf 19.69% 0.166gf 23.51% 0.011gf 1.56% 0.706gf gf 55.27% 0.144gf 19.70% 0.172gf 23.53% 0.011gf 1.50% 0.731gf gf 55.29% 0.149gf 19.71% 0.178gf 23.54% 0.011gf 1.46% 0.756gf 9 of 17

12 PLASTIC MATERIAL CERTIFICATE OF HOUSING 10 of 17

13 PLASTIC MATERIAL CERTIFICATE OF HOUSING 11 of 17

14 PLASTIC MATERIAL CERTIFICATE OF ACTUATOR 12 of 17

15 PLASTIC MATERIAL CERTIFICATE OF ACTUATOR 13 of 17

16 CONTACT MATERIAL CERTIFICATE OF TERMINAL 14 of 17

17 CONTACT MATERIAL CERTIFICATE OF TERMINAL 15 of 17

18 CONTACT MATERIAL CERTIFICATE OF FITTING NAIL 16 of 17

19 CONTACT MATERIAL CERTIFICATE OF FITTING NAIL 17 of 17

20

21 P-TWO INDUSTRIES INC. QUALITY/ENVIRONMENTAL SAFETY POLICIES Satisfying customer & obeying the law and regulations. Protecting pollution, reducing waste & saving energy. All the staff join in & improve frequently. Taking person as foundation & keep safety.