IWLSeries FEATURES APPLICATIONS ORDERING CODE. SMD Wirewound Chip Ferrite Open-Type Inductors (Low Profile) 0805 TRIGON COMPONENTS

Transcription

1 SMD Wirewound Chip Ferrite Open-Type s (Low Profile) 0805 CONFIGURATIONS: FEATURES Size Smaller, Lower profile Higher Efficiency due to the lower loss Higher current in compact size Customer design is welcome at all time RoHS Compliant APPLICATIONS Cellular phones PDAs,Handheld computer Digital cameras MP3 players,gps receivers and more DIMENSION: ITEM IWL0805 A 2.4 (Max) B 1.65 (Max) C 1.20 Max Design Customer s Request Specification D 0.65 (Ref) E 0.44 ORDERING CODE IWL0805 M 220 T ⑴ ⑵ ⑶ ⑷ ⑴ SMT Shielded Power : IWL0805 ⑵ Tolerance Code: J: 5%, K: 10% ⑶ Inductance Code: 220:22uH ⑷ Package: T: Tape/Reel (Standard) Inductance Range: ITEM IWL0805 Inductance 0.1uH~47uH Please refer to complete Ordering Code document (IWL-Ord) for more ordering options. Rev. A3 Page 1 of 8

2 SMD Wirewound Chip Ferrite Open-Type s (Low Profile) 0805 Electrical Characteristics For IWL0805 Series Part Numbers Inductance (uh) / MHz Tolerance Q / MHz (Min) Rdc Type (Ω) Idc Typ (ma) SRF MHz (Min) Color Coding IWL0805 R10T 0.1 / 25 K 20 / White IWL0805 R11T 0.11 / 25 K 25 / White IWL0805 R12T 0.12 / 25 K, J 25 / Violet IWL0805 R15T 0.15 / 25 K, J 25 / Gray IWL0805 R18T 0.18 / 25 K, J 30 / Black IWL0805 R22T 0.22 / 25 K, J 30 / Brown IWL0805 R27T 0.27 / 25 K, J 30 / Red IWL0805 R33T 0.33 / 25 K, J 30 / Orange IWL0805 R39T 0.39 / 25 K, J 30 / Yellow IWL0805 R47T 0.47 / 25 K, J 30 / Green IWL0805 R56T 0.56 / 25 K, J 30 / Blue IWL0805 R62T 0.62 / 25 K, J 30 / Brown IWL0805 R68T 0.68 / 25 K, J 30 / Violet IWL0805 R82T 0.82 / 25 K, J 30 / Gray IWL0805 R91T 0.91 / 25 K, J 30 / Yellow IWL0805 1R0T 1.0 / 7.9 K, J 20 / White IWL0805 1R2T 1.2 / 7.9 K, J 20 / Black IWL0805 1R5T 1.5 / 7.9 K, J 25 / Brown IWL0805 1R8T 1.8 / 7.9 K, J 25 / Red IWL0805 2R2T 2.2 / 7.9 K, J 25 / Orange IWL0805 2R7T 2.7 / 7.9 K, J 25 / Yellow IWL0805 3R3T 3.3 / 7.9 K, J 25 / Green IWL0805 3R9T 3.9 / 7.9 K, J 25 / Blue IWL0805 4R7T 4.7 / 7.9 K, J 25 / Violet IWL0805 5R6T 5.6 / 7.9 K, J 25 / Gray IWL0805 6R8T 6.8 / 7.9 K, J 25 / White Test Freq: when when inductance when inductance Idc: Measured when Inductance drop 10% Irms: For a 15 C rise above 25 C ambient Operating Temp Range: -25 C~+85 C. Rev. A3 Page 2 of 8

3 SMD Wirewound Ferrite Chip Open-Type s (Low Profile) 0805 Electrical Characteristics For IWL0805 Series Part Numbers Inductance (uh) Tolerance Q / MHz (Min) Rdc Type (Ω) Idc Typ (ma) SRF MHz (min) Color Coding IWL0805 8R2T 8.2 / 7.9 K, J 25 / Black IWL T 10 /2.5 K, J 16 / Brown IWL T 12 /2.5 K, J 16 / Red IWL T 15 /2.5 K, J 16 / Orange IWL T 18 /2.5 K, J 16 / Yellow IWL T 22 /2.5 K, J 16 / Green IWL T 27 /2.5 K, J 16 / Blue IWL T 33 /2.5 K, J 16 / Violet IWL T 39 /2.5 K, J 15 / Gray IWL T 47 /2.5 K, J 13 / White When ordering please specify tolerance and packing codes. Ex: IWL0805K8R2T Tolerance: J= ±5%, K= ±10% Packing: T= Clear tape and reel (standard) L, Q, SRF: Agilent/HP E4991A+Agilent/HP16197A Rdc: Chroma Milliohm meter Idc: Inductance drop 10% from the original inductance value without IDC Operating Temperature Range: -40 C~+85 C. Rev. A3 Page 3 of 8

4 IWLSeries SMD Wirewound Ferrite Chip Open-Type s (Low Profile) 0805 Rev. A3 Page 4 of 8

5 SMD Wirewound Ferrite Chip Open-Type s (Low Profile) 0805 Reliability Test ITEM SPACIFICATIONS TEST CONDITION Solderability Resistance to soldering heat The metalized area must have 90% minimum solder coverage. Dip pads in flux and dip in solder pot (96.5 Sn/3.5Ag solder) at 255 C ±5 C. s shall be reflowed onto a PC board using 96.5 Sn/3.5 Ag solder paste. Solder process shall be at a maximum temperature of 260 C. For 96.5 Sn/3.5 Ag solder paste:>217 C for 90 seconds Vibration High temperature resistance Static Humidity Component adhesion (push test) Low temperature resistance Resistance to solvent s must not have a shorted or open winding. s shall be subjected to 0.5Kg There must be no case deformation, change in dimensions, or obliteration of marking. Solder specimen inductor on the test printed circuit board. Apply vibrations in each of the x,y and z directions for 2 house for a total of 6 hours. Frequency : 10~50 Hz Amplitude : 1.5mm s shall be subjected to temperature 85±2 C for 50±12 hours. Measure the test items after leaving the inductors at room temperature and humidity for 2 hours. s shall be subjected to temperature 85±2 C and 90 to 95%RH. For ten 24-hours. Measure the test items after leaving the inductor sat room temperature and humidity for 2 hours. s shall be reflow soldered (255 C ±5 C for 10 seconds) to a tinned copper substrate. A force gauge shall be applied to the side of the component. The device must withstand the stated force without a failure of the termination. s shall be subjected to temperature -25±2 C for 48±12 hours. Measure the test items after leaving the inductors at room temperature and humidity for 1 to 2 hours. s must withstand 6 minutes of alcohol or water. s shall be subjected to 10 cycles to the following temperature cycle: 85 1 cycle 30 min. 30 sec Thermal shock min. Measure the test items after leaving the inductors. At room temperature and humidity for 2 hours. Rev. A3 Page 5 of 8

6 SMD Wirewound Ferrite Chip Open-Type s (Low Profile) 0805 PACKAGE: Cover Tape Peel Strength: The force for tearing off cover tape is 0.1~0.6(N) in the arrow direction at the following Condition: Temperature: 5 ~ 35 C Humidity : 45 ~ 85% Atmospheric pressure : 860 ~ 1060 hpa Tape Dimensions: (Dimensions in mm) Symbol W P P 0 P 1 H T Dimension Rev. A3 Page 6 of 8

7 SMD Wirewound Ferrite Chip Open-Type s (Low Profile) 0805 Reel Dimensions: Symbol T A 180 B 60 C 13 D 14.4 E 8.4 Tapping Figure: (Dimensions in mm) Package Quantity: 180mm Reel Type: 2,000 pcs/reel Packing Label Example: Rev. A3 Page 7 of 8

8 SMD Wirewound Ferrite Chip Open-Type s (Low Profile) 0805 Recommended Soldering Conditions (Please use this product by reflow soldering): Recommended Reflow Pattern, Reflow : until two times 10sec. Max Natural cooling sec. Max. 60sec. Min. Iron Soldering: Use a solder iron of less than 30W when soldering,do not allow the soldering iron tip directly touch the Ceramic body outside of terminal electrode. 4 seconds max. At 260 C. Attention in Case of Using: In case of using product,please avoid following matters: Splashing water or salt water Dew condenses Toxic gas (Hydrogen sulfide, Sulfurous acid,chlorine, Ammonia) Vibrations or shocks which exceed the specified condition Operating temperature range Storage condition : Ferrite Series: -25~+85 C : Temperature: 20 ~25 C, Relative Humidity: 40%~60%. Rev. A3 Page 8 of 8