Page 14, add new paragraph 6.5: Patents

Transcription

1 REVISIONS LTR DESCRIPTION DTE PPROVED B C D E F G Page 14, add new paragraph 6.5: Patents dd three more configurations to drawing. Changed material paragraph. Editorial changes throughout. Changed location of M/2 dimension on configurations E and F of figure 1. Editorial changes throughout Changed center hole in configurations D and E of figure 1. Updated vendor addresses. Editorial changes throughout. Changes in accordance with Notice of Revision 5998-R Inactivate for new design materials contained herein. dd supersession table to section six. Change FSC from 5999 to Editorial changes throughout. Removed references to superseded documents, updated vendor contact information, added environmentally preferable material paragraph, and editorial changes throughout. 24 Oct 85 I. R. Jones 31 ug 87 D. E. Morgan 29 Dec 87 Randy Larson 15 Dec 88 Randy Larson 14 Nov 94 John F. Raye 19 Dec 97 Monica L. Poelking 04 Jun 04 Thomas M. Hess CURRENT DESIGN CTIVITY CGE CODE 037Z3 DEFENSE LOGISTICS GENCY DEFENSE SUPPLY CENTER COLUMBUS INCTIVE FOR NEW DESIGN FTER 19 DECEMBER 1997 Device types contained herein are inactive for new design. FOR NEW DESIGN USE CID Prepared in accordance with SME Y REV G G G G G G G PGE Selected item drawing REV STTUS REV G G G G G G G G G G G G G G G G G OF PGES PGES PMIC N/ Original date of drawing 7 June 1985 PREPRED BY Bernard J. Miesse CHECKED BY David J. Corbett PPROVED BY Monica L. Poelking CODE IDENT. NO. DESIGN CTIVITY DEFENSE ELECTRONICS SUPPLY CENTER DYTON, OH TITLE: HOLDER, ELECTRICL CRD, CRD GUIDE, METL, WITHOUT FLRED ENTRY REV G PGE 1 OF 24 MSC N/ 5998-E048 DISTRIBUTION STTEMENT. pproved for public release; distribution is unlimited.

2 1. SCOPE 1.1 Scope. This drawing describes the requirements for a family of card holders intended for use on printed circuit boards. 1.2 Part or Identifying Number (PIN). The complete PIN shall be as follows: Drawing number 216 Dash number (see table I) N Finish (C, N, or blank) (see 3.3) 2. PPLICBLE DOCUMENTS 2.1 Government documents Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract (see 6.2). DEPRTMENT OF DEFENSE STNDRDS MIL-STD-1285 Marking of Electrical and Electronic Parts. (Copies of these documents are available online at or or from the Standardization Document Order Desk, 700 Robbins venue, Building 4D, Philadelphia, P ) 2.2 Non-Government publications. The following documents form a part of this document to the extent specified herein. Unless otherwise specified, the issues of the documents are those cited in the solicitation or contract (see 6.2). MERICN SOCIETY FOR TESTING ND MTERILS (STM) STM-366/366M Steel Sheets, Carbon, Cold Rolled. STM-967 Standard Specification for Chemical Passivation Treatments for Stainless Steel Parts. STM-B194 Copper-Beryllium lloy Plate, Sheet, Strip, and Rolled Bar (UNS C1700 and C17200). (pplication for copies should be addressed to the STM International, PO Box C700, 100 Barr Harbor Drive, West Conshohocken, P or at URL SOCIETY OF UTOMOTIVE ENGINEERS (SE) SE MS 5517J Steel, Corrosion Resistant, Sheet and Strip (UNS S30100) SE MS-QQ-N-290 Nickel Plating (Electrodeposited). SE MS-QQ-P-416 Plating, Cadmium (Electrodeposited). (pplication for copies should be addressed to the SE World Headquarters, 400 Commonwealth Drive, Warrendale, P or at URL (Industry association specifications and standards are generally available for reference from libraries. They are also distributed among technical groups and using Federal agencies.) 2.3 Order of precedence. In the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. REV G PGE 2

3 3. REQUIREMENTS 3.1 Interface and physical dimensions. See figure 1 and table I. 3.2 Material. Material shall be as specified in table I. Beryllium copper shall be in accordance with STM-B194. Steel shall be in accordance with STM-366/366M (NOTE: Stainless steel in accordance with SE MS 5517J (UNS C30100) may be used in lieu of steel). For configurations, B, D, and E, the material thickness shall be.008 ±.002 inch (0.20 ± 0.05 mm). For configurations C and F, the material thickness shall be.005 ±.001 inch (0.13 ± 0.03 mm). Parts constructed of BH material (see table I) shall have an additional one-quarter heat treat in accordance with STM-B Finish. Card holders constructed of beryllium copper or steel shall be finished with either cadmium plate in accordance with SE MS-QQ-P-416, type II, class 2 or nickel plate in accordance with SE MS-QQ-N-290, class 1, grade G (bright). Card holders with a cadmium plated finish shall include a suffix C and card holders with a nickel plated finish shall include a suffix N (see 1.2). Card holders constructed of stainless steel shall be passivated in accordance with STM-967 (Nitric 2). No finish suffix is needed for passivated stainless steel card holders and the finish suffix in the PIN shall be left blank. 3.4 DSCC certificate of compliance. certificate of compliance shall be submitted to DSCC-VC by each manufacturer desiring to be listed as a suggested source of supply (see 6.7). The certificate shall state that the manufacturer's product meets all the requirements of this drawing Optional statement of compliance in lieu of testing. The acquiring activity, at its discretion, may accept from the manufacturer a statement of compliance in lieu of the manufacturer performing the inspection of product for delivery tests (see and 6.2.c). 3.5 Marking. Marking of the card holder is not required; however, each unit package shall be marked in accordance with MIL-STD-1285 and include the PIN as specified herein (see 1.2), the manufacturer s name or Commercial and Government Entity (CGE) code, and date lot codes. 3.6 Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or environmentally preferable materials should be used to the maximum extent possible provided that the material meets or exceeds the operational and maintenance requirements, and promotes economically advantageous life cycle costs. 3.7 Workmanship. Holders shall be processed in such a manner as to be uniform in quality and shall be free from surface and finish flaws that could affect life or serviceability. Finish shall be smooth and edges shall be rounded. Chipping, cracking, deterioration, disintegration, or burrs are unacceptable. Configuration FIGURE 1. Dimensions and configurations. REV G PGE 3

4 Configuration B Configuration C Configuration D FIGURE 1. Dimensions and configurations - Continued. REV G PGE 4

5 Configuration E Configuration F Inches mm Inches mm Inches Mm Inches mm Inches Mm NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. 3. Unless otherwise specified, tolerances are ±.02 (0.5 mm) on two place decimals and ±.010 (0.25 mm) on three place decimals. FIGURE 1. Dimensions and configurations - Continued. REV G PGE 5

6 TBLE I. Dash numbers. Dash number 1/ Material B Beryllium copper BH Beryllium copper (1/4 HT) S Steel or stainless steel Length (inches) L Board slot thickness ±.005 (0.13 mm) =.0312 (0.79 mm) B =.0625 (1.59 mm) C =.0937 (2.38 mm) Configuration 001* B 2.0 (50.8 mm) 002* BH 2.0 (50.8 mm) D 003* S 2.0 (50.8 mm) 004* B 2.0 (50.8 mm) B 005* BH 2.0 (50.8 mm) B D 006* S 2.0 (50.8 mm) B 007* B 2.0 (50.8 mm) C 008* BH 2.0 (50.8 mm) C D 009* S 2.0 (50.8 mm) C 010* B 2.0 (50.8 mm) B 011* BH 2.0 (50.8 mm) E 012* S 2.0 (50.8 mm) B 013* B 2.0 (50.8 mm) B B 014* BH 2.0 (50.8 mm) B E 015* S 2.0 (50.8 mm) B B 016* B 2.0 (50.8 mm) C B 017* BH 2.0 (50.8 mm) C E 018* S 2.0 (50.8 mm) C B 019* B 2.0 (50.8 mm) C 020* BH 2.0 (50.8 mm) F 021* S 2.0 (50.8 mm) C 022* B 2.0 (50.8 mm) B C 023* BH 2.0 (50.8 mm) B F 024* S 2.0 (50.8 mm) B C 025* B 2.5 (63.5 mm) 026* BH 2.5 (63.5 mm) D 027* S 2.5 (63.5 mm) 028* B 2.5 (63.5 mm) B 029* BH 2.5 (63.5 mm) B D 030* S 2.5 (63.5 mm) B 031* B 2.5 (63.5 mm) C 032* BH 2.5 (63.5 mm) C D 033* S 2.5 (63.5 mm) C See footnote at end of table. REV G PGE 6

7 TBLE I. Dash numbers - Continued. Dash number 1/ Material B Beryllium copper BH Beryllium copper (1/4 HT) S Steel or stainless steel Length (inches) L Board slot thickness ±.005 (0.13 mm) =.0312 (0.79 mm) B =.0625 (1.59 mm) C =.0937 (2.38 mm) Configuration 034* B 2.5 (63.5 mm) B 035* BH 2.5 (63.5 mm) E 036* S 2.5 (63.5 mm) B 037* B 2.5 (63.5 mm) B B 038* BH 2.5 (63.5 mm) B E 039* S 2.5 (63.5 mm) B B 040* B 2.5 (63.5 mm) C B 041* BH 2.5 (63.5 mm) C E 042* S 2.5 (63.5 mm) C B 043* B 2.5 (63.5 mm) C 044* BH 2.5 (63.5 mm) F 045* S 2.5 (63.5 mm) C 046* B 2.5 (63.5 mm) B C 047* BH 2.5 (63.5 mm) B F 048* S 2.5 (63.5 mm) B C 049* B 3.0 (76.2 mm) 050* BH 3.0 (76.2 mm) D 051* S 3.0 (76.2 mm) 052* B 3.0 (76.2 mm) B 053* BH 3.0 (76.2 mm) B D 054* S 3.0 (76.2 mm) B 055* B 3.0 (76.2 mm) C 056* BH 3.0 (76.2 mm) C D 057* S 3.0 (76.2 mm) C 058* B 3.0 (76.2 mm) B 059* BH 3.0 (76.2 mm) E 060* S 3.0 (76.2 mm) B 061* B 3.0 (76.2 mm) B B 062* BH 3.0 (76.2 mm) B E 063* S 3.0 (76.2 mm) B B 064* B 3.0 (76.2 mm) C B 065* BH 3.0 (76.2 mm) C E 066* S 3.0 (76.2 mm) C B See footnote at end of table. REV G PGE 7

8 Dash number 1/ Material B Beryllium copper BH Beryllium copper (1/4 HT) S Steel or stainless steel TBLE I. Dash numbers - Continued. Length (inches) L Board slot thickness ±.005 (0.13 mm) =.0312 (0.79 mm) B =.0625 (1.59 mm) C =.0937 (2.38 mm) Configuration 067* B 3.0 (76.2 mm) C 068* BH 3.0 (76.2 mm) F 069* S 3.0 (76.2 mm) C 070* B 3.0 (76.2 mm) B C 071* BH 3.0 (76.2 mm) B F 072* S 3.0 (76.2 mm) B C 073* B 3.5 (88.9 mm) 074* BH 3.5 (88.9 mm) D 075* S 3.5 (88.9 mm) 076* B 3.5 (88.9 mm) B 077* BH 3.5 (88.9 mm) B D 078* S 3.5 (88.9 mm) B 079* B 3.5 (88.9 mm) C 080* BH 3.5 (88.9 mm) C D 081* S 3.5 (88.9 mm) C 082* B 3.5 (88.9 mm) B 083* BH 3.5 (88.9 mm) E 084* S 3.5 (88.9 mm) B 085* B 3.5 (88.9 mm) B B 086* BH 3.5 (88.9 mm) B E 087* S 3.5 (88.9 mm) B B 088* B 3.5 (88.9 mm) C B 089* BH 3.5 (88.9 mm) C E 090* S 3.5 (88.9 mm) C B 091* B 3.5 (88.9 mm) C 092* BH 3.5 (88.9 mm) F 093* S 3.5 (88.9 mm) C 094* B 3.5 (88.9 mm) B C 095* BH 3.5 (88.9 mm) B F 096* S 3.5 (88.9 mm) B C 097* B 4.0 (101.6 mm) 098* BH 4.0 (101.6 mm) D 099* S 4.0 (101.6 mm) See footnote at end of table. REV G PGE 8

9 Dash number 1/ Material B Beryllium copper BH Beryllium copper (1/4 HT) S Steel or stainless steel TBLE I. Dash numbers - Continued. Length (inches) L Board slot thickness ±.005 (0.13 mm) =.0312 (0.79 mm) B =.0625 (1.59 mm) C =.0937 (2.38 mm) Configuration 100* B 4.0 (101.6 mm) B 101* BH 4.0 (101.6 mm) B D 102* S 4.0 (101.6 mm) B 103* B 4.0 (101.6 mm) C 104* BH 4.0 (101.6 mm) C D 105* S 4.0 (101.6 mm) C 106* B 4.0 (101.6 mm) B 107* BH 4.0 (101.6 mm) E 108* S 4.0 (101.6 mm) B 109* B 4.0 (101.6 mm) B B 110* BH 4.0 (101.6 mm) B E 111* S 4.0 (101.6 mm) B B 112* B 4.0 (101.6 mm) C B 113* BH 4.0 (101.6 mm) C E 114* S 4.0 (101.6 mm) C B 115* B 4.0 (101.6 mm) C 116* BH 4.0 (101.6 mm) F 117* S 4.0 (101.6 mm) C 118* B 4.0 (101.6 mm) B C 119* BH 4.0 (101.6 mm) B F 120* S 4.0 (101.6 mm) B C 121* B 4.5 (114.3 mm) 122* BH 4.5 (114.3 mm) D 123* S 4.5 (114.3 mm) 124* B 4.5 (114.3 mm) B 125* BH 4.5 (114.3 mm) B D 126* S 4.5 (114.3 mm) B 127* B 4.5 (114.3 mm) C 128* BH 4.5 (114.3 mm) C D 129* S 4.5 (114.3 mm) C 130* B 4.5 (114.3 mm) B 131* BH 4.5 (114.3 mm) E 132* S 4.5 (114.3 mm) B See footnote at end of table. REV G PGE 9

10 Dash number 1/ Material B Beryllium copper BH Beryllium copper (1/4 HT) S Steel or stainless steel TBLE I. Dash numbers - Continued. Length (inches) L Board slot thickness ±.005 (0.13 mm) =.0312 (0.79 mm) B =.0625 (1.59 mm) C =.0937 (2.38 mm) Configuration 133* B 4.5 (114.3 mm) B B 134* BH 4.5 (114.3 mm) B E 135* S 4.5 (114.3 mm) B B 136* B 4.5 (114.3 mm) C B 137* BH 4.5 (114.3 mm) C E 138* S 4.5 (114.3 mm) C B 139* B 4.5 (114.3 mm) C 140* BH 4.5 (114.3 mm) F 141* S 4.5 (114.3 mm) C 142* B 4.5 (114.3 mm) B C 143* BH 4.5 (114.3 mm) B F 144* S 4.5 (114.3 mm) B C 145* B 5.0 (127.0 mm) 146* BH 5.0 (127.0 mm) D 147* S 5.0 (127.0 mm) 148* B 5.0 (127.0 mm) B 149* BH 5.0 (127.0 mm) B D 150* S 5.0 (127.0 mm) B 151* B 5.0 (127.0 mm) C 152* BH 5.0 (127.0 mm) C D 153* S 5.0 (127.0 mm) C 154* B 5.0 (127.0 mm) B 155* BH 5.0 (127.0 mm) E 156* S 5.0 (127.0 mm) B 157* B 5.0 (127.0 mm) B B 158* BH 5.0 (127.0 mm) B E 159* S 5.0 (127.0 mm) B B 160* B 5.0 (127.0 mm) C B 161* BH 5.0 (127.0 mm) C E 162* S 5.0 (127.0 mm) C B 163* B 5.0 (127.0 mm) C 164* BH 5.0 (127.0 mm) F 165* S 5.0 (127.0 mm) C See footnote at end of table. REV G PGE 10

11 Dash number 1/ Material B Beryllium copper BH Beryllium copper (1/4 HT) S Steel or stainless steel TBLE I. Dash numbers - Continued. Length (inches) L Board slot thickness ±.005 (0.13 mm) =.0312 (0.79 mm) B =.0625 (1.59 mm) C =.0937 (2.38 mm) Configuration 166* B 5.0 (127.0 mm) B C 167* BH 5.0 (127.0 mm) B F 168* S 5.0 (127.0 mm) B C 169* B 5.5 (139.7 mm) 170* BH 5.5 (139.7 mm) D 171* S 5.5 (139.7 mm) 172* B 5.5 (139.7 mm) B 173* BH 5.5 (139.7 mm) B D 174* S 5.5 (139.7 mm) B 175* B 5.5 (139.7 mm) C 176* BH 5.5 (139.7 mm) C D 177* S 5.5 (139.7 mm) C 178* B 5.5 (139.7 mm) B 179* BH 5.5 (139.7 mm) E 180* S 5.5 (139.7 mm) B 181* B 5.5 (139.7 mm) B B 182* BH 5.5 (139.7 mm) B E 183* S 5.5 (139.7 mm) B B 184* B 5.5 (139.7 mm) C B 185* BH 5.5 (139.7 mm) C E 186* S 5.5 (139.7 mm) C B 187* B 5.5 (139.7 mm) C 188* BH 5.5 (139.7 mm) F 189* S 5.5 (139.7 mm) C 190* B 5.5 (139.7 mm) B C 191* BH 5.5 (139.7 mm) B F 192* S 5.5 (139.7 mm) B C 193* B 6.0 (152.4 mm) 194* BH 6.0 (152.4 mm) D 195* S 6.0 (152.4 mm) 196* B 6.0 (152.4 mm) B 197* BH 6.0 (152.4 mm) B D 198* S 6.0 (152.4 mm) B See footnote at end of table. REV G PGE 11

12 Dash number 1/ Material B Beryllium copper BH Beryllium copper (1/4 HT) S Steel or stainless steel TBLE I. Dash numbers - Continued. Length (inches) L Board slot thickness ±.005 (0.13 mm) =.0312 (0.79 mm) B =.0625 (1.59 mm) C =.0937 (2.38 mm) Configuration 199* B 6.0 (152.4 mm) C 200* BH 6.0 (152.4 mm) C D 201* S 6.0 (152.4 mm) C 202* B 6.0 (152.4 mm) B 203* BH 6.0 (152.4 mm) E 204* S 6.0 (152.4 mm) B 205* B 6.0 (152.4 mm) B B 206* BH 6.0 (152.4 mm) B E 207* S 6.0 (152.4 mm) B B 208* B 6.0 (152.4 mm) C B 209* BH 6.0 (152.4 mm) C E 210* S 6.0 (152.4 mm) C B 211* B 6.0 (152.4 mm) C 212* BH 6.0 (152.4 mm) F 213* S 6.0 (152.4 mm) C 214* B 6.0 (152.4 mm) B C 215* BH 6.0 (152.4 mm) B F 216* S 6.0 (152.4 mm) B C 1/ * represents the finish and shall be replaced by C or N (NOTE: If passivated stainless steel material is used, no suffix code is required). 4. VERIFICTION 4.1 Conformance inspections Inspection of product for delivery. Inspection of product for delivery shall consist of visual and mechanical inspections of interface and physical dimensions (see 3.1), materials (see 3.2), and workmanship (see 3.7). Criteria for defects are listed in Optional statement of compliance. The acquiring activity, at its discretion, may accept a statement of compliance in lieu of the manufacturer performing the inspection of product for delivery (see 6.2.b) Sampling plan. sample of parts shall be randomly selected in accordance with table II, normal sampling. If one or more defects are found, the lot shall be rejected. Criteria for defects are listed in Rejected lots. If an inspection lot is rejected after normal sampling inspection, the manufacturer may rework it to correct the defects, or screen out the defective parts and resubmit for inspection. Resubmitted lots shall be inspected by selecting a random sample of parts in accordance with table II, tightened sampling. If one or more defects are found in this sample, the lot shall be rejected and shall not be supplied to this specification. Resubmitted lots which are acceptable shall be clearly identified as reinspected lots. REV G PGE 12

13 TBLE II. Sampling plan. Lot size Normal Tightened 2 to to to to to to to 1, ,201 to 3, ,201 to 10, ,001 and over Defective characteristics and properties. Dimensional characteristics are considered defective when out of tolerance. Physical and functional properties are considered defective when outside the specified minimum, maximum, or range as applicable. Workmanship characteristics are considered defective when they would be detrimental to the intended use, performance requirements, or environmental survival of the part. 5. PCKGING 5.1 Packaging. For acquisition purposes, the packaging requirements shall be as specified in the contract or order (see 6.2). When actual packaging of materiel is to be performed by DoD or in-house contractor personnel, these personnel need to contact the responsible packaging activity to ascertain packaging requirements. Packaging requirements are maintained by the Inventory Control Point's packaging activity within the Military Department or Defense gency, or within the Military Department's system command. Packaging data retrieval is available from the managing Military Department's or Defense gency's automated packaging files, CD-ROM products, or by contacting the responsible packaging activity. 6. NOTES (This section contains information of a general or explanatory nature which may be helpful, but is not mandatory.) 6.1 Intended use. Card holders conforming to this drawing are intended for use when performance specifications do not exist and qualified military devices that will perform the required function are not available for OEM application Environmentally preferable material. Environmentally preferable materials should be used to the maximum extent possible that the material meets or exceeds the operational and maintenance requirements, and promotes economically advantageous life cycle costs. Table III lists the Environmental Protection gency (EP) top seventeen hazardous materials targeted for major usage reduction. If any of these hazardous materials are required, it is recommended that it be used only when other materials cannot meet performance requirements. TBLE III. EP top seventeen hazardous materials. Benzene Dichloromethane Tetrachloroethylene Cadmium and Compounds Lead and Compounds Toluene Carbon Tetrachloride Mercury and Compounds 1,1,1 - Trichloroethane Chloroform Methyl Ethyle Ketone Trichloroethylene Chromium and Compounds Methyl Isobutyl Ketone Xylenes Cyanide and Compounds Nickel and Compounds REV G PGE 13

14 6.1.2 Guidance on use of alternative parts with less hazardous or nonhazardous materials. This drawing provides for a number of alternative plating materials via the PIN. Users should select the PIN with the least hazardous material that meets the form, fit and function requirements of their application. 6.2 cquisition requirements. The acquisition requirements should specify the following: a. Complete PIN (see 1.2). b. Requirements for delivery and one copy of the quality conformance inspection data or certificate of compliance that parts have passed quality conformance inspection with each shipment of parts by the manufacturer. c. Whether the manufacturer performs the product for delivery inspection (4.1.1) or provides an optional statement of compliance (4.1.2). d. Requirements for notification of change in product to the contracting activity, if applicable. e. Requirements for packaging, if other than standard commercial packaging is desired. 6.3 Replaceability. Devices covered by this drawing will replace the commercial device covered by a contractor-prepared specification or drawing. 6.4 Patents. The items covered by this drawing may be covered under Patent Number 3,186,554. The Government does not possess a license under these patents for the benefit of manufacturers of the item, either for the Government or for use in equipment to be delivered to the Government. 6.5 Supersession data. This drawing includes the essential requirements of previous revisions and supersedes previous PIN designations (see 1.2). The original version of this drawing covered only cadmium plated parts, which were represented by part numbers without suffix letters. Part numbers in subsequent revisions included suffix letters to denote optional finishes. (NOTE: If passivated stainless steel material is used, no suffix code is required). Superseding DSCC drawing PIN per B dated 31 ugust 1987 (1) -XXXC Superseded DESC drawing PIN per dated 24 October 1985 (1) -XXX (1) XXX represents the possible dash numbers (001 through 216). 6.6 Users of record. Coordination of this document for future revisions are coordinated only with the suggested sources of supply and the users of record of this document. Requests to be added as a recorded user of this drawing should be in writing to: DSCC-VC, Post Office Box 3990, Columbus, OH or by telephone (614) or DSN or by electronic mail at 5998_Documents@dscc.dla.mil. 6.7 Suggested sources of supply. Suggested sources of supply are listed herein. dditional sources will be added as they become available. For assistance in the use of this drawing, contact DSCC-VC, Post Office Box 3990, Columbus, OH or by telephone (614) or DSN or by electronic mail at 5998_Documents@dscc.dla.mil. This document is available online at REV G PGE 14

15 DSCC drawing PIN (1) (2) Vendor similar designation or type number (3) DSCC drawing PIN (1) (2) Vendor similar designation or type number (3) Vendor CGE Vendor name, address and contact information 001* 002* * 005* * 008* * 011* * 014* * 017* * 020* * 023* B C-1543BH CR B C-1543BH CR B C-1543BH CR B C-1544BH CR B C-1544BH CR B C-1544BH CR B C-1545BH CR B C-1545BH CR * 050* * 053* * 056* * 059* * 062* * 065* * 068* * 071* B C-1543BH CR B C-1543BH CR B C-1543BH CR B C-1544BH CR B C-1544BH CR B C-1544BH CR B C-1545BH CR B C-1545BH CR PW Electronic Solutions Danielson Street Poway, C Tel: (858) Toll Free: (800) Fax: (858) URL: Electronic-mail: sales.electronicsolutions@apw.com 025* 026* * 029* * 032* * 035* * 038* * 041* * 044* * 047* B C-1543BH CR B C-1543BH CR B C-1543BH CR B C-1544BH CR B C-1544BH CR B C-1544BH CR B C-1545BH CR B C-1545BH CR * 074* * 077* * 080* * 083* * 086* * 089* * 092* * 095* B C-1543BH CR B C-1543BH CR B C-1543BH CR B C-1544BH CR B C-1544BH CR B C-1544BH CR B C-1545BH CR B C-1545BH CR-207 See notes at end of table. REV G PGE 15

16 DSCC drawing PIN (1) (2) Vendor similar designation or type number (3) DSCC drawing PIN (1) (2) Vendor similar designation or type number (3) Vendor CGE Vendor name, address and contact information 097* 098* * 101* * 104* * 107* * 110* * 113* * 116* * 119* B C-1543BH CR B C-1543BH CR B C-1543BH CR B C-1544BH CR B C-1544BH CR B C-1544BH CR B C-1545BH CR B C-1545BH CR * 146* * 149* * 152* * 155* * 158* * 161* * 164* * 167* B C-1543BH CR B C-1543BH CR B C-1543BH CR B C-1544BH CR B C-1544BH CR B C-1544BH CR B C-1545BH CR B C-1545BH CR PW Electronic Solutions Danielson Street Poway, C Tel: (858) Toll Free: (800) Fax: (858) URL: Electronic-mail: sales.electronicsolutions@apw.com 121* 122* * 125* * 128* * 131* * 134* * 137* * 140* * 143* B C-1543BH CR B C-1543BH CR B C-1543BH CR B C-1544BH CR B C-1544BH CR B C-1544BH CR B C-1545BH CR B C-1545BH CR * 170* * 173* * 176* * 179* * 182* * 185* * 188* * 191* B C-1543BH CR B C-1543BH CR B C-1543BH CR B C-1544BH CR B C-1544BH CR B C-1544BH CR B C-1545BH CR B C-1545BH CR-211 See notes at end of table. REV G PGE 16

17 DSCC drawing PIN (1) (2) Vendor similar designation or type number (3) DSCC drawing PIN (1) (2) Vendor similar designation or type number (3) Vendor CGE Vendor name, address and contact information 193* 194* * 197* * 200* * 203* B C-1543BH CR B C-1543BH CR B C-1543BH CR B C-1544BH CR * 206* * 209* * 212* * 215* B C-1544BH CR B C-1544BH CR B C-1545BH CR B C-1545BH CR PW Electronic Solutions Danielson Street Poway, C Tel: (858) Toll Free: (800) Fax: (858) URL: Electronic-mail: sales.electronicsolutions@apw.com (1) Parts must be purchased to this DSCC PIN to assure that all performance requirements and tests are met. (2) The * suffix represents the finish designator C or N. Dash numbers with no suffix are passivated stainless steel material and require no finish designator. (3) The part numbers ending with 3 represent card holders with a cadmium finish. For card holders with nickel plate finish, the last digit 3 shall be replaced with a 6 (i.e., B-1046). DSCC drawing PIN (1) (2) Vendor similar designation or type number (3) DSCC drawing PIN (1) (2) Vendor similar designation or type number (3) Vendor CGE Vendor name, address and contact information 001* 002* 003* 004* 005* 006* 007* 008* 009* 010* 011* 012* 013* 014* 015* 016* 017* 018* 019* 020* 021* 022* 023* 024* SIY-001 SIY-002 SIY-003 SIY-004 SIY-005 SIY-006 SIY-007 SIY-008 SIY-009 SIY-010 SIY-011 SIY-012 SIY-013 SIY-014 SIY-015 SIY-016 SIY-017 SIY-018 SIY-019 SIY-020 SIY-021 SIY-022 SIY-023 SIY * 026* 027* 028* 029* 030* 031* 032* 033* 034* 035* 036* 037* 038* 039* 040* 041* 042* 043* 044* 045* 046* 047* 048* SIY-025 SIY-026 SIY-027 SIY-028 SIY-029 SIY-030 SIY-031 SIY-032 SIY-033 SIY-034 SIY-035 SIY-036 SIY-037 SIY-038 SIY-039 SIY-040 SIY-041 SIY-042 SIY-043 SIY-044 SIY-045 SIY-046 SIY-047 SIY Sigmation, Incorporated 4549 Gateway Circle Dayton, OH Tel: (937) Fax: (937) Electronic-mail: sigmation@ameritech.net See notes at end of table. REV G PGE 17

18 DSCC drawing PIN (1) Vendor similar designation or type number DSCC drawing PIN (1) Vendor similar designation or type number Vendor CGE Vendor name, address and contact information 049* 050* 051* 052* 053* 054* 055* 056* 057* 058* 059* 060* 061* 062* 063* 064* 065* 066* 067* 068* 069* 070* 071* 072* SIY-049 SIY-050 SIY-051 SIY-052 SIY-053 SIY-054 SIY-055 SIY-056 SIY-057 SIY-058 SIY-059 SIY-060 SIY-061 SIY-062 SIY-063 SIY-064 SIY-065 SIY-066 SIY-067 SIY-068 SIY-069 SIY-070 SIY-071 SIY * 098* 099* 100* 101* 102* 103* 104* 105* 106* 107* 108* 109* 110* 111* 112* 113* 114* 115* 116* 117* 118* 119* 120* SIY-097 SIY-098 SIY-099 SIY-100 SIY-101 SIY-102 SIY-103 SIY-104 SIY-105 SIY-106 SIY-107 SIY-108 SIY-109 SIY-110 SIY-111 SIY-112 SIY-113 SIY-114 SIY-115 SIY-116 SIY-117 SIY-118 SIY-119 SIY Sigmation, Incorporated 4549 Gateway Circle Dayton, OH Tel: (937) Fax: (937) Electronic-mail: 073* 074* 075* 076* 077* 078* 079* 080* 081* 082* 083* 084* 085* 086* 087* 088* 089* 090* 091* 092* 093* 094* 095* 096* SIY-073 SIY-074 SIY-075 SIY-076 SIY-077 SIY-078 SIY-079 SIY-080 SIY-081 SIY-082 SIY-083 SIY-084 SIY-085 SIY-086 SIY-087 SIY-088 SIY-089 SIY-090 SIY-091 SIY-092 SIY-093 SIY-094 SIY-095 SIY * 122* 123* 124* 125* 126* 127* 128* 129* 130* 131* 132* 133* 134* 135* 136* 137* 138* 139* 140* 141* 142* 143* 144* SIY-121 SIY-122 SIY-123 SIY-124 SIY-125 SIY-126 SIY-127 SIY-128 SIY-129 SIY-130 SIY-131 SIY-132 SIY-133 SIY-134 SIY-135 SIY-136 SIY-137 SIY-138 SIY-139 SIY-140 SIY-141 SIY-142 SIY-143 SIY-144 See notes at end of table. REV G PGE 18

19 DSCC drawing PIN (1) (2) 145* 146* 147* 148* 149* 150* 151* 152* 153* 154* 155* 156* 157* 158* 159* 160* 161* 162* 163* 164* 165* 166* 167* 168* 169* 170* 171* 172* 173* 174* 175* 176* 177* 178* 179* 180* Vendor similar designation or type number (3) SIY-145 SIY-146 SIY-147 SIY-148 SIY-149 SIY-150 SIY-151 SIY-152 SIY-153 SIY-154 SIY-155 SIY-156 SIY-157 SIY-158 SIY-159 SIY-160 SIY-161 SIY-162 SIY-163 SIY-164 SIY-165 SIY-166 SIY-167 SIY-168 SIY-169 SIY-170 SIY-171 SIY-172 SIY-173 SIY-174 SIY-175 SIY-176 SIY-177 SIY-178 SIY-179 SIY-180 DSCC drawing PIN (1) (2) 181* 182* 183* 184* 185* 186* 187* 188* 189* 190* 191* 192* 193* 194* 195* 196* 197* 198* 199* 200* 201* 202* 203* * 206* 207* 208* 209* 210* 211* 212* 213* 214* 215* 216* Vendor similar designation or type number (3) SIY-181 SIY-182 SIY-183 SIY-184 SIY-185 SIY-186 SIY-187 SIY-188 SIY-189 SIY-190 SIY-191 SIY-192 SIY-193 SIY-194 SIY-195 SIY-196 SIY-197 SIY-198 SIY-199 SIY-200 SIY-201 SIY-202 SIY-203 SIY-204 SIY-205 SIY-206 SIY-207 SIY-208 SIY-209 SIY-210 SIY-211 SIY-212 SIY-213 SIY-214 SIY-215 SIY-216 Vendor CGE Vendor name, address and contact information Sigmation, Incorporated 4549 Gateway Circle Dayton, OH Tel: (937) Fax: (937) Electronic-mail: (1) Parts must be purchased to this DSCC PIN to assure that all performance requirements and tests are met. (2) The * suffix represents the finish designator C or N when applicable. NOTE: If passivated stainless steel material is used, no suffix code is required. (3) These part numbers represent card holders with a cadmium finish. Vendor CGE will also manufacture card holders with a nickel plate finish and assign part numbers in the future. REV G PGE 19

20 6.8 Supersession data. Superseded part numbers are listed below. Superseding (new) part number (1) Superseded (old) part number (2) -001* -002* 55563/02D20G (3) * -005* 55563/02DB20G (3) * -008* 55563/02DC20G (3) * -011* 55563/04D20G (3) * -014* 55563/04DB20G (3) * -017* 55563/04DC20G (3) * -020* 55563/06D20G (3) * -023* 55563/06DB20G (3) * -026* 55563/02D25G (3) * -029* 55563/02DB25G (3) * -032* 55563/02DC25G (3) * -035* 55563/04D25G (3) * -038* 55563/04DB25G (3) * -041* 55563/04DC25G (3) * -044* 55563/06D25G (3) -045 See notes at end of table. REV G PGE 20

21 Superseding (new) part number (1) Superseded (old) part number (2) -046* -047* 55563/06DB25G (3) * -050* 55563/02D30G (3) * -053* 55563/02DB30G (3) * -056* 55563/02DC30G (3) * -059* 55563/04D30G (3) * -062* 55563/04DB30G (3) * -065* 55563/04DC30G (3) * -068* 55563/06D30G (3) * -071* 55563/06DB30G (3) * -074* 55563/02D35G (3) * -077* 55563/02DB35G (3) * -080* 55563/02DC35G (3) * -083* 55563/04D35G (3) * -086* 55563/04DB35G (3) * -089* 55563/04DC35G (3) -090 See notes at end of table. REV G PGE 21

22 Superseding (new) part number (1) Superseded (old) part number (2) -091* -092* 55563/06D35G (3) * -095* 55563/06DB35G (3) * -098* 55563/02D40G (3) * -101* 55563/02DB40G (3) * -104* 55563/02DC40G (3) * -107* 55563/04D40G (3) * -110* 55563/04DB40G (3) * -113* 55563/04DC40G (3) * -116* 55563/06D40G (3) * -119* 55563/06DB40G (3) * -122* 55563/02D45G (3) * -125* 55563/02DB45G (3) * -128* 55563/02DC45G (3) * -131* 55563/04D45G (3) * -134* 55563/04DB45G (3) -135 See notes at end of table. REV G PGE 22

23 Superseding (new) part number (1) Superseded (old) part number (2) -136* -137* 55563/04DC45G (3) * -140* 55563/06D45G (3) * -143* 55563/06DB45G (3) * -146* 55563/02D50G (3) * -149* 55563/02DB50G (3) * -152* 55563/02DC50G (3) * -155* 55563/04D50G (3) * -158* 55563/04DB50G (3) * -161* 55563/04DC50G (3) * -164* 55563/06D50G (3) * -167* 55563/06DB50G (3) * -170* 55563/02D55G (3) * -173* 55563/02DB55G (3) * -176* 55563/02DC55G (3) * -179* 55563/04D55G (3) -180 See notes at end of table. REV G PGE 23

24 Superseding (new) part number (1) Superseded (old) part number (2) -181* -182* 55563/04DB55G (3) * -185* 55563/04DC55G (3) * -188* 55563/06D55G (3) * -191* 55563/06DB55G (3) * -194* 55563/02D60G (3) * -197* 55563/02DB60G (3) * -200* 55563/02DC60G (3) * -203* 55563/04D60G (3) * -206* 55563/04DB60G (3) * -209* 55563/04DC60G (3) * -212* 55563/06D60G (3) * -215* 55563/06DB60G (3) -216 (1) in the superseding part number represents the finish and shall be replaced by or F. (2) The * in the superseding part number represents the finish and shall be replaced by C or N. Card holders made of passivated stainless steel require no suffix code. (3) When stainless steel is used, only finish code G is available (15 th character position of superseding part number). REV G PGE 24