DILLARD'S INC TEST PROTOCOL FOR DILL USA- (V19) HAIR ACCESSORIES (HAIR / BOBBY PINS / CLIPS) (ADULT / CHILD & INFANT)

Transcription

1 By/Date: Page 1 of 5 Evaluation Citation / ethod No. of Criteria Notes esult ating SCOPE: This protocol is applicable for testing of hair accessories (Hair bobby pins clips) for children, infant and adult. SUPPLEENTY POTOCOL Note: additional cost, sample size and TT may be required if testing to 1 or more supplemental protocols is necessary.please refer to the below referenced supplemental protocol(s) for additional information. California Proposition 65 DILL-N-PTCL US - The sample should be reviewed against the requirements of California Proposition 65. Children's products DILL-TY-PTCL US samples shall be reviewed against the requirements of children s product protocol to determine if additional testing or labeling is required. LBELING US Packaging labeling Country of origin marking Use labeling NLYTICL Total lead in surface coating Nickel spot test on metal F.P. and L. ct (16 CF 500) O NIST Uniform Laws and egulations Handbook Packaging shall be labelled with the following, Product Identification Net quantity of contents shall be expressed in terms of weight or mass, measure, numerical count, or combination so as to give accurate information to facilitate consumer comparison (U.S. and metric units) anufacturer, packer, or distributor s name & address (City, State & Zip Code) 19 CF Shall indicate country of origin legibly, permanently, and in comparable size and close proximity to any mention of country other than country in which the article was manufactured or produced. ust be visible at point of purchase. CPSC-CH-E / CPSD-N PD C 12471:2002 / CPSD-N Use/care instructions shall be clear, concise and understandable, provide step-by-step method of use and be provided in language appropriate to destination countries. Provide a copy of the instructions in the report. - accessible surface coatings in the as received state on items outside of the scope of 16 CF 1303 shall not contain lead or lead components in which the lead content is in excess of 0.009% (90 ppm) of the weight of the total content. eport actual results or include data table within report. Component testing is allowed. Compositing up to 3 colors is allowed. 1 Shall show negative test result for finished metallic components on products that come into direct and prolonged contact with skin.

2 By/Date: Page 2 of 5 Evaluation Citation / ethod No. of Criteria Notes esult ating Nickel in metal EN1811:2011+1:2015 / EN 12472:2005+1:2009 / CPSD-N a. Post assemblies, which are inserted into pierced parts of the human body, shall have nickel release rate less than 0.2 micrograms per square centimeter per week (µg/cm²/week). b. rticle parts, which are inteneded to come into direct and prolonged contact with the skin, shall not have nickel release rate greater than 0.5 micrograms per square centimeter per week (µg/cm²/week) Note: - Perform full test when the result for nickel spot test is positive or inconclusive. - ccording to EN1811:2011+1:2015, because of the combined measurement uncertainty of 46%, an article is non-compliant only when the nickel release is greater than or equal to 0.35 µg/cm²/week and 0.88 µg/cm²/week for post assemblies and components of direct and prolonged skin contact respectively. zo dyes in textile and leather EN ISO :2017 / ISO :2015 / CPSD-N / CPSD-N PHYSICL CHCTEISTICS Dimensions - length Dimensions - width Weight ** [By request only] Fabric and leather materials, which may come into direct and prolonged contact with human skin, are prohibited from using azo dyes, which are capable of decomposing into one or more aromatic amines (22 amines refer standard), which have levels present in excess of 30 mg/kg. Note: - Compositing up to 3 materials is allowed - follow method composite guideline. - The composite result will be evaluated against the adjusted limit (regulatory limit divided by the number of colors in the composite). If any color in the composite exceeds the limit, then test with individual colors will be analyzed. (each color is charged separately) - equirement with reference to EC No. 1907/2006 annex XVII and its amendments item no. 43 eport average length; shall meet label claims eport overall width; shall meet label claims eport overall weight; shall meet label claims.

3 By/Date: Page 3 of 5 Evaluation Citation / ethod No. of Dimensions - length Dimensions - thickness Number of pieces WOKNSHIP Sharp point and sharp edge Defects and workmanship PEFONCE ctual use - functionality Durability Tension test for removal of components Torque test for removal of components Effects of extreme temperature change esistance to corrosion COLOFSTNESS Colorfastness to rotary crocking 16 CF & 49 (od) CPSD-GB CPSD-GB ST F Sec. 8.9 (od) ST F Sec. 8.8 (od) CPSD-HL ST B (mod) / CPSD-HL [ange] eport overall length; shall meet label claims eport overall thickness; shall meet label claims s claimed. Criteria Notes esult ating Shall have no sharp points / edges, other than those required for function. odification: Expanded scope to other products. Shall have no discernible surface degradation, including crazing, shivering, denting, bubbles, cracks, stains, deformations, chips, fractures, heavy lines, waves, shear marks, scratches, scuff marks, indentations, or blisters. Shall have no components missing, malformed, and/or fractured. Shall perform as intended, as received. 2 [Clasping] 100 times cycling; open/close report failure cycle 1 ust withstand 15 lb. for 10 seconds with no failure. odification = Expanded scope to other products. 1 ust withstand 4.2 In. / lb. with no failure. odification = Expanded scope to other products hours at 0 F and 120 F - No failure or visual change. 1 [pplicable to samples or sample components constructed of metal or samples with metallic coatings that can be exposed to the environment] Shall withstand 24 hours in 1% salt spray (fog) with no noticeable oxidation / corrosion / visual changes. odification: 1% salt spray (fog). TCC [ colors] Dry: Grade 4.0 minimum Wet: Grade 3.0 minimum

4 By/Date: Page 4 of 5 Evaluation Citation / ethod No. of Colorfastness to TCC [ colors] perspiration Grade 3 inimun Criteria Notes esult ating NOTE ON SPLE SELECTION: Dillard's Testing Protocol addresses "epresentative Sampling" by requiring every style to be tested at least once per Season. Further, When Selecting Style to be sent for Testing, the Vendor/Factory Quality representative should randomly select finished products which have been fully produced in the Factory ssembly lines and comply with all supplied( or authorized by Dillard's) Style and BO specifications. No. Of equired for Complete Testing No. Of (Fully Packed) Cartons For Transit Testing: No. Of Working Days For Complete Testing: 6 1 (Only Upon Dillard's equest) 7 Client pproval: Creation Date: Last evision Date: Pricing eview Date Lucy Feng 12/Jan/ /Nov/ /Feb/2018 Technical eview Date: Key dditional Charge For This Test andatory egulatory esult Key C N N NT Claimed ecorded eets Does Not eet Not pplicable Not Tested ating Key PSS Pass

5 By/Date: Page 5 of 5 ating Key FIL N Fail Not equested