Replaces Ryan GA30-06 Parts 9 4 1 6 2 7 8 3 Item R&R O.E.M. Req. No. Part No. Part No. Description Qty. 1 R233 233 R&R Ball Bearing, Connecting Rod 8 1 R2333 2333 R&R Ball Bearing, Crankshaft 4 1 R2334 2334 R&R Ball Bearing, Crank Support 4 1 R832499 832499 R&R Bearing, Connecting Rod 8 2 R234 234 R&R Pivot Pin, Old Style Model 9110 & 9210 8 2 R2403 2403 R&R Pivot Pin, New Style Model 44882-1 & Up 8 3 R237 237 R&R Belt, Drive 1 4 R2342 2342 R&R Chain, Drive 3 R876324 887284 R&R Brake Shoe 4 6 R2347 2347 R&R Tine Holder, 1" Mounting Dia. 4 7 R33-1300 83237 R&R Element, Air Filter 1 8 R821814 821814 Use R82619 8 R82619 82619 R&R Fuel Filter 1 9 R22123 22123 R&R Connecting Link 1 1087
Replaces Ryan GA30 Parts Alloy Solid Tines These tines aerate without the work of cleaning up the mess of cores and debris left behind with conventional core aerating. R&R Solid Tines are manufactured from a special high-carbon steel bar and heat treated to RC4-48 in our own heat treat facility. They are available in all standard sizes but are especially popular in the smaller diameters for aerating in the summer months to relieve the stress on greens by allowing water, air and nutrients to easily flow into the root zone. With the combination of small holes and no cores, play can be resumed immediately. R201422 Needle, Alloy.196 3.00 0.196 - - R201423 Needle, Alloy.196 4.70 0.196 - - R201334 Solid, Alloy.00 2.00.20 - - R23863 Solid, Alloy.00.000.20 - - R201413 Solid, Alloy.62.00.312 - - R201412 Solid, Alloy.62.00.37 - - R201411 Solid, Alloy.62.00.00 - - R201400 Solid, Alloy.70 4.70.20 - - R201414 Solid, Alloy.70.00.312 - - R20141 Solid, Alloy.70.00.37 - - R201416 Solid, Alloy.70.00.00 - - R201417 Solid, Alloy.70.00.62 - - R201409 Solid, Alloy.87.00.437 - - R201418 Solid, Alloy.87.00.62 - - R201419 Solid, Alloy.87.00.70 - - Alloy Shatter Tines With their + shape, R&R shatter tines relieve compaction and allow water, air and nutrients to flow in the root zones and beyond with virtually no visible surface disturbance. Because of their unique shape the aerating area is maximized while allowing play to be resumed immediately. R&R Shatter Tines are manufactured from special high-carbon alloy investment castings and heat treated to RC4-48 in our own facility to insure you of optimum quality. 1088 R20146 Shatter, Alloy.00 4.62.37 cross - - R201 Shatter, Alloy.00 4.62.00 cross - - R20147 Shatter, Alloy.62 4.62.37 cross - - R20160 Shatter, Alloy.62 4.62.00 cross - - R201619 Shatter, Alloy.62.00.62 cross - - R20149 Shatter, Alloy.70 4.70.37 cross - - R20170 Shatter, Alloy.70 4.70.00 cross - - R201620 Shatter, Alloy.70.00.62 cross - - R201621 Shatter, Alloy.87.00.62 cross - - All original equipment manufacturers names and part numbers are used for identification purposes only, and we are in no way implying that our products are original equipment parts. Prices subject to change without notice.
Replaces Ryan GA30 Parts Standard Hollow Tines Designed to remove a soil core, R&R Standard Hollow Tines are constructed from case hardened tubular steel and are the most economical tines available. Case hardening hardens the inner and outer surfaces of the tine wall to over RC for added wear. R2327 Hollow, Standard.62.00.440.33.049 R23274 Hollow, Standard.62.00.20.400.049 R9-3690 Hollow, Standard.70 4.70.47.330.049 R23472 Hollow, Standard.70.00.20.400.049 R201410 Hollow, Standard.70.00.640.30.049 R201442 Hollow, Standard.70.00.660.30.062 Alloy Hollow Tines Like Standard Hollow Tines, this line is also tubular and designed to remove a soil core, but they are constructed from a special high carbon alloy steel. The steel tubing is specially manufactured for R&R to achieve uniform hardness of RC4-48 throughout the tine for excellent wear and toughness. These tines are much tougher and resist bending in extremely hard or rocky soils and you can expect 3-4 times longer life than from the Standard Hollow Tines. R20186 Hollow, Alloy.70.00.20.400.049 R20188 Hollow, Alloy.70.00.600.400.072 R20187 Hollow, Alloy.70.00.630.20.049 R20189 Hollow, Alloy.70.00.670.00.072 Carbide-Tipped Alloy Hollow Tines The R&R Carbide-Tipped Alloy Hollow Tine construction is the same special high carbon alloy steel tubing and hardened to RC4-48 as the alloy hollow tines, with the addition of a carbide tip for even longer life. The advantage of using carbide tipped tines is the ability to maintain your maximum aerating depth consistently over the life of the tines. You can expect these tines to last 6-8 times longer than the R&R Standard Hollow Tines. Carbide tipped tines are not recommended in rocky soil conditions, as carbide, which is extremely wear resistant, can break when encountering hard impacts in rocks. R20144 Hollow, Carbide Tipped.70".00".42".270".072" R201440 Hollow, Carbide Tipped.70.00.10.37.049 R201447 Hollow, Carbide Tipped.70".00".2".30.072" R201449 Hollow, Carbide Tipped.70".00".630".480".072" R201441 Hollow, Carbide Tipped.70.00.630.00.049 Alloy Slicing Knife Tines These tines allow water, air and nutrients to flow into the root zones and beyond with virtually no visible surface disturbance, allowing play to be resumed immediately. All of these tines are precision machined out of solid high-carbon alloy steel bar and heat treated in our own facility to RC4-48 and carry the same lifetime guarantee of quality as all our other tines. 1089 R20147 Slicing Knife, Alloy.70 4.70.70 x.160
Replaces Ryan GA30 Parts Hollow Alloy Side-Eject Tines Manufactured from special high carbon alloy tubular steel with a precision machined slot in the side wall to allow for more efficient core removal in heavy soils. R&R s unique method of machining maintains the maximum side wall height for strength to avoid bending. These tines are through hardened to RC4-48 to create a much tougher and more wear resistant tine. R20193 Side Eject, Hollow Alloy.70.0.40.30.072 R20194 Side Eject, Hollow Alloy.70.0.670.00.072 Machined Alloy Side-Eject Tines These alloy tines remove a soil core which quickly exits the side of the tine through a precision machined slot. This slot is designed to avoid plugging that can occur using hollow tubular tines (especially the smaller diameters) in heavy soil conditions. R&R manufactures a wide selection of these side-eject tines machined from special high-carbon alloy steel solid bar and heat treated to RC4-48 in our own heat treating facility. These side eject tines are very popular for the multiple tine holders which fit all greens aerators. R201634 Side Eject, Machined Alloy.00 3.00.44.320.049 R20163 Side Eject, Machined Alloy.00 3.00.70.430.06 R23864 Side Eject, Machined Alloy.00 4.000.370.20.060 R20119 Side Eject, Machined Alloy.00 4.00.30.240.049 R201636 Side Eject, Machined Alloy.00 4.00.440.330.049 R201638 Side Eject, Machined Alloy.00.00.460.32.06 R20120 Side Eject, Machined Alloy.62 4.000.30.220.06 R201637 Side Eject, Machined Alloy.62 4.00..42.06 R20121 Side Eject, Machined Alloy.70 4.000.30.230.049 R2013 Side Eject, Machined Alloy.70.00.430.300.06 R20136 Side Eject, Machined Alloy.70.00.440.330.049 R20137 Side Eject, Machined Alloy.70.00.60.00.06 1090 Alloy Spoons All R&R Alloy Spoons are stamped and formed from special high strength alloy sheet steel and heat treated in our own facility to RC4-48. These spoons are all side eject by design for dependable plug ejection and extremely strong for heavy duty applications such as fairways, collars and tees. They are also a great value for your money. R201408 Closed Spoon, Open Side,Alloy.87.00.800.00.10 R834973 Closed Spoon, Open Side,Alloy.87.00.92.62.10 All original equipment manufacturers names and part numbers are used for identification purposes only, and we are in no way implying that our products are original equipment parts. Prices subject to change without notice.
Replaces Ryan GA30 Parts Carbide-Tipped Machined Alloy Side Eject Tines These alloy tines remove a soil core which quickly exits the side of the tine through a precision machined slot. This slot is designed to avoid plugging that can occur using hollow tubular tines (especially the smaller diameters) in heavy soil conditions. R&R manufactures a wide selection of these side-eject tines machined from special high-carbon alloy steel solid bar and heat treated to RC4-48 in our own heat treating facility. A carbide tip is then added for even longer life. The advantage of using carbide tipped tines is the ability to maintain your maximum aerating depth consistently over the life of the tines. R20167 New! R201677 New! R201679 New! R201676 New! R201678 New! R201680 New! R20169 New! R201696 New!.00" 3.00".400".300".049".00" 3.00".4".400".062".00" 3.00".64".00".062".00" 4.00".400".300".049".00" 4.00".4".400".062".00" 4.00".64".00".062".70" 3.00".64".00".062".70" 4.00".64".00".062" Carbide-Tipped Hollow Alloy Side-Eject Tines Manufactured from special high carbon alloy tubular steel with a precision machined slot in the side wall to allow for more efficient core removal in heavy soils. R&R s unique method of machining maintains the maximum side wall height for strength to avoid bending. These tines are through hardened to RC4-48 to create a much tougher and more wear resistant tine. A carbide tip is then added for even longer life. The advantage of using carbide tipped tines is the ability to maintain your maximum aerating depth consistently over the life of the tines. R201446 R201448 R20140 Side Eject, Hollow Alloy - Carbide Tipped.70".00".42".27".072" Side Eject, Hollow Alloy - Carbide Tipped.70".00".2".30".072" Side Eject, Hollow Alloy - Carbide Tipped.70".00".630".480".072" 1091
Replaces Ryan GA30 Parts Tine Holders & Traction Unit 8 6 8 2 7 8 3 7 1 4 6 4 7 7 7 4 7 9 11 10 12 13 14 17 1 16 Cylinder Repair Kit 20 21 22 23 24 18 19 1092 All original equipment manufacturers names and part numbers are used for identification purposes only, and we are in no way implying that our products are original equipment parts. Prices subject to change without notice.
Replaces Ryan GA30 Parts Tine Holders & Traction Unit Item R&R O.E.M. Req. No. Part No. Part No. Description Qty. 1 R47600 47702 R&R 3 Tine Holder, 3/4" Tine Mounting Dia., Incl. #8 4 1 R47601 47601 R&R 3 Tine Holder, /8" Tine Mounting Dia., Incl. #8 4 1 R47639 47639 R&R 3 Tine Holder, 7/8" Tine Mounting Dia., Incl. #8 4 2 R47848 47848 R&R Tine Holder, 1/2" Tine Mounting Dia., Incl. #8 4 3 R201429 R&R Only R&R Tine Holder,Fits Needle Tines Only 4 4 R47601S 819804 R&R Stud, Tine Holder, 1/2-20 8 4 R47600S R&R Stud, Tine Holder, 7/16-20 8 R30632 30632 R&R Lock Washer, /16" A/R 6 R0098 0098 R&R Bolt, /16-18 x 1-1/4" A/R 7 R322-306416 R&R Bolt, /16-18 x 1" A/R 8 R32128-31 R&R Flanged Locknut, 1/2-20 A/R 9 R23026 23026 R&R 4 Finger Turf Hold Down 1 use with 3 Tine Holder 10 R23027 23027 R&R 3 Finger Turf Hold Down 3 use with 3 Tine Holder 11 R24193 24193 R&R 6 Finger Turf Hold Down 1 use with Tine Holder 12 R24192 24192 R&R Finger Turf Hold Down 3 use with Tine Holder 13 R22887 22887 R&R Drive Belt, 2V 1 14 R821814 821814 Use R82619 14 R82619 82619 R&R Fuel Filter 1 1 R23-9740 22972 R&R Hyd. Oil Filter 1 16 R38672 23127 R&R Bearing A/R 16 RA203603 832498 R&R Bearing A/R 16 R832499 832499 R&R Bearing A/R 17 R390836 R&R Tire, 24-13 x 12, 4 Ply Dico Turf Trac 2 18 R886001 886001 R&R Seal Kit, Cylinder 1 19 R47613 47613 R&R Brake Lining, (Set of 2 with Rivits) 2 20 R80027 80027 R&R Rivet, Brake Lining 6 21 R83081 83081 R&R Choke Control 1 21 R23292 23292 Use R83081 22 R23097 23097 R&R Chain 2 23 R2287 2287 R&R Pivot Pin 4 24 R87994 87994 R&R Starter Solenoid 1 1093
Replaces Ryan Greensaire II & WG-24 Parts Alloy Solid Tines These tines aerate without the work of cleaning up the mess of cores and debris left behind with conventional core aerating. R&R Solid Tines are manufactured from a special high-carbon steel bar and heat treated to RC4-48 in our own heat treat facility. They are available in all standard sizes but are especially popular in the smaller diameters for aerating in the summer months to relieve the stress on greens by allowing water, air and nutrients to easily flow into the root zone. With the combination of small holes and no cores, play can be resumed immediately. R201422 Solid, Needle Alloy.196 3.00.196 - - R201423 Solid, Needle Alloy.196 4.70.196 - - R201334 Solid, Overseeding Alloy.00 2.00.20 - - R23863 Solid, Alloy.00.000.20 - - R201330 Solid, Alloy.00.000.312 - - R201349 Solid, Alloy.62 4.00.20 - - R201341 Solid, Alloy.62 4.00.312 - - R201344 Solid, Alloy.62 4.00.37 - - R20134 Solid, Alloy.62 4.00.00 - - R201432 Solid, Alloy.70 4.37.312 - - R201433 Solid, Alloy.70 4.37.37 - - R201434 Solid, Alloy.70 4.37.00 - - R201346 Solid, Alloy.70 4.00.62 - - Alloy Shatter Tines With their + shape, R&R shatter tines relieve compaction and allow water, air and nutrients to flow in the root zones and beyond with virtually no visible surface disturbance. Because of their unique shape the aerating area is maximized while allowing play to be resumed immediately. R&R Shatter Tines are manufactured from special high-carbon alloy investment castings and heat treated to RC4-48 in our own facility to insure you of optimum quality. R20146 Shatter, Alloy.00 4.62.37 cross - - R201 Shatter, Alloy.00 4.62.00 cross - - R20147 Shatter, Alloy.62 4.62.37 cross - - R20160 Shatter, Alloy.62 4.62.00 cross - - R20149 Shatter, Alloy.70 4.62.37 cross - - R20170 Shatter, Alloy.70 4.62.00 cross - - R201620 Shatter, Alloy.70.00.62 cross - - 1094 All original equipment manufacturers names and part numbers are used for identification purposes only, and we are in no way implying that our products are original equipment parts. Prices subject to change without notice.
Replaces Ryan Greensaire II & WG-24 Parts Standard Hollow Tines Designed to remove a soil core, R&R Standard Hollow Tines are constructed from case hardened tubular steel and are the most economical tines available. Case hardening hardens the inner and outer surfaces of the tine wall to over RC for added wear. R20133 Hollow, Standard.62 4.00.390.260.049 R201336 Hollow, Standard.62 4.00.420.300.049 R201337 Hollow, Standard.62 4.00.20.400.049 R201338 Hollow, Standard.70 4.00.640.30.049 Alloy Hollow Tines Like Standard Hollow Tines, this line is also tubular and designed to remove a soil core, but they are constructed from a special high carbon alloy steel. The steel tubing is specially manufactured for R&R to achieve uniform hardness of RC4-48 throughout the tine for excellent wear and toughness. These tines are much tougher and resist bending in extremely hard or rocky soils and you can expect 3-4 times longer life than from the Standard Hollow Tines. R20181 Hollow, Alloy.62 4.00.20.400.049 R20183 Hollow, Alloy.70 4.00.600.400.072 R20182 Hollow, Alloy.70 4.00.640.30.049 R20184 Hollow, Alloy.70 4.00.670.00.072 Carbide-Tipped Alloy Hollow Tines The R&R Carbide-Tipped Alloy Hollow Tine construction is the same special high carbon alloy steel tubing and hardened to RC4-48 as the alloy hollow tines, with the addition of a carbide tip for even longer life. The advantage of using carbide tipped tines is the ability to maintain your maximum aerating depth consistently over the life of the tines. You can expect these tines to last 6-8 times longer than the R&R Standard Hollow Tines. Carbide tipped tines are not recommended in rocky soil conditions, as carbide, which is extremely wear resistant, can break when encountering hard impacts in rocks. R201340 Hollow, Carbide Tipped.62 4.00.10.37.049 R201339 Hollow, Carbide Tipped.70 4.00.630.00.049 R20108 Hollow, Carbide Tipped.70" 4.70".42".27".072" R20110 Hollow, Carbide Tipped.70" 4.70".2".30".072" R20112 Hollow, Carbide Tipped.70" 4.70".630".480".072" 109
Replaces Ryan Greensaire II & WG-24 Parts Machined Alloy Side-Eject Tines These alloy tines remove a soil core which quickly exits the side of the tine through a precision machined slot. This slot is designed to avoid plugging that can occur using hollow tubular tines (especially the smaller diameters) in heavy soil conditions. R&R manufactures a wide selection of these side-eject tines machined from special high-carbon alloy steel solid bar and heat treated to RC4-48 in our own heat treating facility. These side eject tines are very popular for the multiple tine holders which fit all greens aerators. R201634 Side Eject, Machined Alloy.00 3.00.44.320.049 R20163 Side Eject, Machined Alloy.00 3.00.60.420.06 R23864 Side Eject, Machined Alloy.00 4.000.370.20.060 R20119 Side Eject, Machined Alloy.00 4.00.30.240.049 R201636 Side Eject, Machined Alloy.00 4.00.460.300.070 R20120 Side Eject, Machined Alloy.62 4.000.30.220.06 R201637 Side Eject, Machined Alloy.62 4.00.60.420.06 R20121 Side Eject, Machined Alloy.70 4.00.30.230.049 R20123 Side Eject, Machined Alloy.70 4.70.40.300.06 R20124 Side Eject, Machined Alloy.70 4.70.40.400.06 R2012 Side Eject, Machined Alloy.70 4.70.60.00.06 Hollow Alloy Side-Eject Tines Manufactured from special high carbon alloy tubular steel with a precision machined slot in the side wall to allow for more efficient core removal in heavy soils. R&R s unique method of machining maintains the maximum side wall height for strength to avoid bending. These tines are through hardened to RC4-48 to create a much tougher and more wear resistant tine. R2019 Side Eject, Hollow Alloy.70 4.00.600.400.072 R20196 Side Eject, Hollow Alloy.70 4.00.670.00.072 1096 Alloy Slicing Knife Tines These tines allow water, air and nutrients to flow into the root zones and beyond with virtually no visible surface disturbance, allowing play to be resumed immediately. All of these tines are precision machined out of solid high-carbon alloy steel bar and heat treated in our own facility to RC4-48 and carry the same lifetime guarantee of quality as all our other tines. R20144 Slicing Knife, Alloy.62 4.00.62 x.160 - - R2014 Slicing Knife, Alloy.70 4.00.70 x.160 - - All original equipment manufacturers names and part numbers are used for identification purposes only, and we are in no way implying that our products are original equipment parts. Prices subject to change without notice.
Replaces Ryan Greensaire II & WG-24 Parts Carbide-Tipped Machined Alloy Side Eject Tines These alloy tines remove a soil core which quickly exits the side of the tine through a precision machined slot. This slot is designed to avoid plugging that can occur using hollow tubular tines (especially the smaller diameters) in heavy soil conditions. R&R manufactures a wide selection of these side-eject tines machined from special high-carbon alloy steel solid bar and heat treated to RC4-48 in our own heat treating facility. A carbide tip is then added for even longer life. The advantage of using carbide tipped tines is the ability to maintain your maximum aerating depth consistently over the life of the tines. R20167 R201677 R201679 R201676 R201678 R201680 R20168 R201687 R201686 R201688 R20169 R201696.00" 3.00".400".300".049".00" 3.00".4".400".062".00" 3.00".64".00".062".00" 4.00".400".300".049".00" 4.00".4".400".062".00" 4.00".64".00".062".62" 3.00".4".400".062".62" 3.00".64".00".062".62" 4.00".4".400".062".62" 4.00".64".00".062".70" 3.00".64".00".062".70" 4.00".64".00".062" Carbide-Tipped Hollow Alloy Side-Eject Tines Manufactured from special high carbon alloy tubular steel with a precision machined slot in the side wall to allow for more efficient core removal in heavy soils. R&R s unique method of machining maintains the maximum side wall height for strength to avoid bending. These tines are through hardened to RC4-48 to create a much tougher and more wear resistant tine. A carbide tip is then added for even longer life. The advantage of using carbide tipped tines is the ability to maintain your maximum aerating depth consistently over the life of the tines. R20109 Side Eject, Hollow Alloy - Carbide Tipped.70" 4.70".42".27".072" R20111 Side Eject, Hollow Alloy - Carbide Tipped.70" 4.70".2".30".072" R20113 Side Eject, Hollow Alloy - Carbide Tipped.70" 4.70".630".480".072" 1097
Replaces Ryan Greensaire II & WG-24 Parts Tine Holders 10 33 31 2 3 1 8 7 12 11 9 10 17 43 16 1 42 4 13 39 31 6 32 24 2 22 23 3 3 40 27 26 See Next Page 18 19 21 1 20 1 14 23 44 29 28 30A 29 30 8 9 60 38 41 Genuine Briggs & Stratton engines and parts available 36 37 1098 REPLACES RYAN "NEW STYLE" SLIDE AND GUIDE ASSEMBLY PARTS 1 48 49 0 46 47 2 4 2 47 49 LUBRICATION FREE R&R Products reengineered R201100 slide assemblies (Replaces Ryan Part #4978) are manufactured with special triple layered composite bushings. The use of these bushings eliminates the need for lubrication and insures against oil leakage on turf surfaces. R&R also uses triple lipped seals and induction hardened hard chrome plated shafts for added life. 3 4 46 REPLACES RYAN 24 TINE HOLDER ASSEMBLY PARTS 30A 24 TINE HOLDER ASSEMBLY R201300 R&R 24 Tine Holder Assembly Kit Includes: 6 Tine Holders, 6 Washers, 2 Brackets, 1 Mounting Plate, & 1 Turf Hold-down 7 6 44 Individual Parts also available in listing All original equipment manufacturers names and part numbers are used for identification purposes only, and we are in no way implying that our products are original equipment parts. Prices subject to change without notice.
Replaces Ryan Greensaire II & WG-24 Parts Tine Holders Item R&R GA II WG24 Req. No. Part No. Part No. Part No. Description Qty. 1 R48229 48229 R&R Fitting, Grease 12 2 R30683 30683 B42 R&R Bolt, 3/8-16 x 1-1/4" 12 2 R48001 48001 Use R30683 3 R120177 120177 LW4 R&R Lock Washer, 3/8" 12 4 R48308 Use R4306 4 R4306 SBG1 R&R Insert, Two Halves 4 4 R4306 4306 R&R Insert, Two Halves 6 R316796 316796 B147 R&R Bolt, 1/4-20 x 1" 12 6 R48181 48181 LW7 R&R Lock Washer 12 7 R203023 203023 B9 R&R Bolt, 1/4-20 x 3/4" 6 8 R48181 48181 LW7 R&R Lock Washer 6 9 R1764 1118A Use R48811 9 R48811 48811 1118A R&R Pin, Dowel 6 10 R47293 47293 R&R Retainer Assembly with Bearing 12 11 R44446 BG43 R&R Bearing Retainer Assembly 6 includes 2 Part #R47293 &1 Part #R48811 12 R48797 48797 R&R Bearing, Needle 12 13 R44300 44300 1090A R&R Rod Assembly 6 13 R44302 44302 Use R44300 6 14 R1731 1731 1078A3 R&R Pin, Slide Assy. 6 1 R48869 48869 BG38 R&R Bearing 6 16 R17731 17731 Use R4643. 16 R4643 4643 R&R Retainer, Spring 17 R1803 1803 SP4 R&R Spring 6 18 R4890 4890 B11 R&R Bolt, 3/8-16 x 1" Nyloc 24 19 R17729 17729 113 R&R Bushing, Guide Assembly 12 20 R44102 44102 112 R&R Guide Assembly, includes: 6 21 R22639 4824 OS9 R&R Oil Seal 12 22 R1749 1749 1089A Use R22642 22 R22642 22642 R&R Push Rod, Induction Hardened 6 23 R4822 Thin OS7 R&R Oil Seal Serial #7173 & under 12 23 R48277 OS32 Use R48274 23 R48274 48274 OS32 R&R Oil Seal 12 24 R4478 4478 1074A3 R&R Slide Assembly; with 2 each R2026 bushings, R48229 grease fittings & R48274 oil seals 6 2 R48827 48827 R&R Bolt, Nyloc 1/4-20 x 1/2" 6 26 R316797 316797 R&R Bolt, 1/4-20 x 1-1/4" 12 27 R48181 48181 R&R Lock Washer, 1/4" 12 28 R0098 0098 B27 R&R Bolt, /16-18 x 1-1/4" 6 29 R30632 30632 LW4 R&R Lock Washer, /16" 6 30 R2032 2032 1070A R&R 2 Tine Holder 6 30 R2073 2073 1070A R&R 2 Tine Holder 6 30A R47849 47849 R&R 4 Tine Holder,.00 Tine Mounting Dia. 6 30B R201424 R&R Only R&R 4 Tine Holder, Fits Needle Tines Only 6 30B R201301 R&R Only R&R 4 Tine Holder, /8" Mounting Dia. 6 31 R48128 BG49 R&R Bearing 2 31 R4881 4881 R&R Bearing 3 32 R20228 20228 R&R Race, Inner 1 33 R48814 48814 R&R Race, Inner 2 3 R1726 107A1 R&R Bushing, Slide Assembly 12 3 R2026 2026 R&R Bushing, Slide Assembly 1 O.D. 12 1099
Replaces Ryan Greensaire II & WG-24 Parts Tine Holders 1100 Item R&R GA II WG24 Req. No. Part No. Part No. Part No. Description Qty. 36 R48878 R&R Tire, 13-6.0 x 6, 2 Ply Rib 2 36 R484 1010 WG-1 R&R Tire, 11-4.00 x, 2 Ply Rib 2 37 R4892 4892 R&R Belt 1 38 R2142 2142 R&R Chain #0 1 38 R46406 1021WG-2 R&R Chain #40 1 38 R46431 1064A R&R Chain #0 1 38 R46434 1064A R&R Chain #0 Crank 2 38 R4674 4674 R&R Chain #40 1 38 R48887 48887 R&R Chain #0 1 38 R48888 48888 Use R2142 38 R48889 48889 R&R Chain #40 1 38 R48890 48890 R&R Chain #40 1 38 R48891 48891 R&R Chain #0, Crankshaft 2 38 R4000 R&R Offset Link #40 A/R 40 R4104 4104 R&R Deflector incl. R48827 6 41 R4883 4883 R&R Throttle Control 1 42 R800427 800427 R&R Hex Head Bolt, Slide Assy. 6 43 R48911 48911 R&R Flanged Whiz Nut, Slide Assy. 6 44 R23249 23249 R&R Flat Washer 6 4 R496 496 R&R Guide Assy., Incl 2 ea. #46 & 1 ea. #0 6 46 R22637 22637 R&R Bushing, Guide Assy., 12 Triple Layered Composite 47 R22636 22636 R&R Bushing, Slide Assy., 12 Triple Layered Composite 48 R30699 30699 R&R Plug, Shaft End 6 49 R22640 22640 R&R Seal, Slide Assy., Triple Lip 12 0 R22639 22639 R&R Seal, Guide Assy., Triple Lip 12 1 R22641 22641 R&R Felt Plug, Slide Assy., 6 (not used on R&R Slide) 2 R17692 17692 R&R Felt Pad, Slide Assy., 12 (not used on R&R Slide) 3 R4890 4890 R&R Bolt, 3/8-16 x 1" Nyloc 24 4 R4978 48978 Use R201100 4 R201100 R&R Only R&R Lubrication Free Slide Assy. 6 Complete with Induction Hardened & Hard Chrome plated shaft, Incl. items #47-49 R24196 24196 R&R Turf Hold-down, 1 use only with 4 Tine Holders R201302 R&R Only R&R Turf Hold-down, 1 use with 4 Tine Holder with.62 Tines 6 R20326 20326 R&R Mounting Plate, Turf Hold-down 1 7 R24014 24014 R&R Bracket 2 8 R330748 330748 R&R Bolt, Socket Head, /16-18 x 1" 1 9 R800694 800694 R&R Bolt, Hex Head, /16-18 x 2-1/2" 2 60 R122140 122140 R&R Lock Washer,.312 2 All original equipment manufacturers names and part numbers are used for identification purposes only, and we are in no way implying that our products are original equipment parts. Prices subject to change without notice.
Replaces Ryan / Cushman GA60 Parts Alloy Solid Tines These tines aerate without the work of cleaning up the mess of cores and debris left behind with conventional core aerating. R&R Solid Tines are manufactured from a special high-carbon steel bar and heat treated to RC4-48 in our own heat treat facility. They are available in all standard sizes but are especially popular in the smaller diameters for aerating in the summer months to relieve the stress on greens by allowing water, air and nutrients to easily flow into the root zone. With the combination of small holes and no cores, play can be resumed immediately. R201409 Solid, Alloy.87.00.437 - - R201418 Solid, Alloy.87.00.62 - - R201419 Solid, Alloy.87.00.70 - - Alloy Shatter Tines With their + shape, R&R shatter tines relieve compaction and allow water, air and nutrients to flow in the root zones and beyond with virtually no visible surface disturbance. Because of their unique shape the aerating area is maximized while allowing play to be resumed immediately. R&R Shatter Tines are manufactured from special high-carbon alloy investment castings and heat treated to RC4-48 in our own facility to insure you of optimum quality. R201620 Shatter, Alloy.70.00.62 cross - - R201621 Shatter, Alloy.87.00.62 cross - - Alloy Slicing Knife Tines These tines allow water, air and nutrients to flow into the root zones and beyond with virtually no visible surface disturbance, allowing play to be resumed immediately. All of these tines are precision machined out of solid high-carbon alloy steel bar and heat treated in our own facility to RC4-48 and carry the same lifetime guarantee of quality as all our other tines. R20147 Slicing Knife, Alloy.70.00.70 x.160 - - Alloy Spoons All R&R Alloy Spoons are stamped and formed from special high strength alloy sheet steel and heat treated in our own facility to RC4-48. These spoons are all side eject by design for dependable plug ejection and extremely strong for heavy duty applications such as fairways, collars and tees. They are also a great value for your money. 1101 R201408 Closed Spoon, Side Eject,Alloy.87.00.800.00.10 R834973 Closed Spoon, Side Eject,Alloy.87.00.92 62.10
Replaces Ryan Renovaire-Tracaire Parts 8 6 7 1 2 3 4 Item R&R O.E.M. Req. No. Part No. Part No. Description Qty. 1 R201310 1196 R&R 1/2" Closed Spoon 96 2 R201320 4366 R&R 1/2" Open Spoon 96 1 R201311 1197 R&R 3/4" Closed Spoon 96 2 R201321 R&R 3/4" Open Spoon 96 Tech Note: All above spoons 7-1/2" long with /16 mounting hole 3 R201312 1191 R&R Renovating Tine 96 R201313 1193 R&R 4" Slicing Knife 96 4 R201314 1194 R&R 6" Slicing Knife 96 Tech Note: All above knives mounting holes 2-1/2" on center 6 R1198 1198 R&R Clamp, Spoon 96 7 R306836 306836 R&R Bolt 192 8 R48804 48804 R&R Flanged Locknut 192 R231-3 4890 R&R Tire 4.80 x 8, 4 Ply T.T. Ind. Stud Goodyear 2 R232-3 R&R 4.80 x 8 Tube 2 R24-78 38174 R&R Bearing, Wheel 4 R24-79 808088 R&R Cup, Wheel 4 R4826 4826 R&R Seal, Aerating Wheel 24 Replaces Ryan Lawnaire 28 Parts 1102 Item R&R O.E.M. Req. No. Part No. Part No. Description Qty. R47709 47709 Use R201106 R201106 R&R Only R&R Tine Assy., 3/4", Side Ejection 4 Heat Treated Aircraft Alloy Steel RA203603 832498 R&R Bearing, Link Arm R38672 23127 R&R Bearing, Crankshaft All original equipment manufacturers names and part numbers are used for identification purposes only, and we are in no way implying that our products are original equipment parts. Prices subject to change without notice.
Replaces Ryan Mataway, Ren-O-Thin & Spike-Aire Parts 1 2 3 4 Item R&R O.E.M. Req. No. Part No. Part No. Description Qty. 1 R201323 16901 R&R Mataway Straight 1/32" 1 R201323C New! R&R Only R&R Mataway Straight 1/32", Carbide Tipped 1 R201324 16898 R&R Mataway Straight 1/8" 1 R201324C New! R&R Only R&R Mataway Straight 1/8", Carbide Tipped 1 R20132 16900 R&R Mataway Straight 1/16" 1 R20132C New! R&R Only R&R Mataway Straight 1/16", Carbide Tipped 1 R201326 16899 R&R Mataway Offset 1/16" Tech Note: 7-1/4" Long, 1" Hex mounting hole (all above mataways) 2 R201327 16897 R&R Ren-o-thin Flail 1/8 2 R201327C New! R&R Only R&R Ren-o-thin Flail 1/8, Carbide Tipped 3 R201328 16920 R&R Spiker Blade, 13 Point Tech Note: 10" diameter, 1" Hex mounting hole, 12ga (.104) thick) 4 R23293 23293 R&R Spiker Blade, 8 Point R4779 4779 R&R Drive Belts (Matched Set of 3), Fits Mataway Replaces Ryan Lawnaire IV Parts 1103 Item R&R O.E.M. Req. No. Part No. Part No. Description Qty. 1 R22361 22361 R&R 3/4" Closed Spoon, 14 GA.
Replaces Ryan Sod Cutter Parts 2 1 3 Item R&R O.E.M. Req. No. Part No. Part No. Description Qty. 1 R2036 R&R Only R&R 12" Sod Cutter Blade, 1/4" x 2 1/2" 1 R2039 R&R Only R&R 1" Sod Cutter Blade, 1/4" x 2 1/2" 1 R2038 R&R Only R&R 16" Sod Cutter Blade, 1/4" x 2 1/2" 1 R2033 R&R Only R&R 18" Sod Cutter Blade, 1/4" x 2 1/2" R48082 48082 R&R Bearing, Fits VI R48092 48092 R&R Bearing, Fits Jr. & V2 R48093 48093 R&R Bearing, Fits Jr. V1 & V2 R48421 48421 R&R Belt, Fits Jr. Machine R48438 48438 R&R Belt, Single for Briggs Engine R4821 4821 R&R Belt, Matched for Briggs Engine R482 482 R&R Belt, Matched for Wis. Engine R48608 48608 R&R Belt, Matched 24" Machine 2 R2040 R&R /16" x 1" Gr. 8 Hardened Bolt w/lock Washer & Lock Nut, pkg of 2 2 R20406 R&R /16" x 1" Gr. 8 Hardened Bolt w/whiz Nut, pkg of 2 3 R16061 16061 R&R Cutter Blade Arm, Fits Jr. R21438 21438 R&R Seal, Side Arm R48138 48138 R&R Bearing, Needle R21436 21436 R&R Bearing Replaces Ryan Cutt-Off Parts R&R Part No. Description Striaght Edge Blades R20380 R&R Straight Cutt-Off Blade, Fits 12" Sod Cutter R20382 R&R Straight Cutt-Off Blade, Fits 1" Sod Cutter R20384 R&R Straight Cutt-Off Blade, Fits 16" Sod Cutter R2038 R&R Straight Cutt-Off Blade, Fits 18" Sod Cutter R20386 R&R Straight Cutt-Off Blade, Fits 24" Sod Cutter 1104 Serrated Edge Blades R201380 R&R Serrated Cutt-Off Blade, Fits 12" Sod Cutter R201382 R&R Serrated Cutt-Off Blade, Fits 1" Sod Cutter R201384 R&R Serrated Cutt-Off Blade, Fits 16" Sod Cutter R20138 R&R Serrated Cutt-Off Blade, Fits 18" Sod Cutter R201386 R&R Serrated Cutt-Off Blade, Fits 24" Sod Cutter All original equipment manufacturers names and part numbers are used for identification purposes only, and we are in no way implying that our products are original equipment parts. Prices subject to change without notice.