PRODUCT C ATA L O G U E
CHOOSE THE RIGHT PRODUCT 1. Floor finishes and oils Waterbased Solventbased Oils No need for sealing SEALMASTER for roller, applicator Quick drying SEALER for stainless steel trowel No need for sealing Exotic wood NATURAL oil SEALERS Tinted floor NATURAL oil + TINTING PASTE - Floor oil + TINTING PASTE Ready-mixed WOOD FILLER for joints and cracks < 1,5mm To be mixed MIXIT for joints and cracks < 3mm Filler DECK OIL NATURAL DOMO CLASSIC HARDWAX OIL URE- THANE SPORT COMBI UV-FIT WOOD UV-FIT NovaBEST STAR TOP BASIC PRO Area of use Domestic Office Commercial, public Sport floors Levelled floors, LVT TOP COATS Outdoor 2. Maintenance products Regular cleaning SUPER CLEAN SUPER CLEAN SOAP Periodic cleaning NEWSHINE NEWSHINE RE-COVER Special cleaning REMOVER REMOVER REMOVER WATERBASED FINISHES MIXIT 6 WOOD FILLER 7 SEALMASTER 8 SEALER 9 BASIC 10 PRO 11 TOP 5 12 TOP 13 NovaBEST 14 STAR 15 SPORT TEAM 16 UV-FIT system 19 SOLVENTBASED FINISHES URETHANE 23 CLASSIC 24 OILS HARDWAX OIL 27 NATURAL 28 DOMO 29 RE-COVER 30 DECK OIL 31 TINTING PASTE 32 MAINTENANCE AND CARE SUPER CLEAN 34 SOAP 34 NEWSHINE 35 REMOVER 35 SPECIAL PRODUCTS 36 TECHNICAL FAQ 38
WATERBASED FINISHES WATERBASED FINISHES Synteko waterbased sealers are for sealing wooden and parquet floors before applying Synteko waterbased top coats. Synteko sealers can be used on practially all wood species as well as on untreated cork. They are fast drying and ready to use. Synteko waterbased top coats are intended to use on hardwood and parquet floors, as well as on untreated cork floors and other wood products. They can be used on untreated or previously finished surfaces. All Synteko waterbased floor finishes are NMP-free, not -yellowing and low-odour. BEFORE USING THE FLOOR The floor can be used with caution 24 hours after the last coat is applied. Furniture can be placed after 24 hours. Allow the moisture to evaporate for 1 week before laying rugs. Final curing of surface after 1 week. Do not clean floor with water or detergents during the first month. Attach felt pads to the legs of chairs and tables in order to avoid scratching the finish. The surface must not be covered with non-porous protective materials. NB! Detailed information and instructions are provided on the Product Information sheet and MSDS (Material Safety Data Sheet). This document only presents a selection of key information. PLEASE NOTE! Waterborne floor finishes must not be covered with solventborne finishes. Oily and resinous wood species such as teak should be coated as soon as possible after machine sanding. All finishes should be shaken before use. Do this before vacuu ming so that the air mixed into the finish during shaking has a few minutes to escape before use. Wood that has been chemically treated or mechanically compressed can not be finished with waterborne finishes. Stained floors should not be sealed but finished directly with Synteko waterbased finishes. Do not apply more than two coats per day (sealer and/ or finish). Chemically pre-treated wood or mechanically compressed wood should be treated according to the manufacturer s recommendations. Do not use tape directly on the finished floor. Never use silicon products in the vicinity of finishing work. Bear in mind that tools must not be wet when you begin finishing. Check for water inside the roller. Remember that floor temperature can be much lower than air temperature. Turn off powerful mechanical ventilation systems prior to fini shing. Reduce the floor-heating temperature prior to finishing. The ideal drying time of the second and final coat should always be app. 2 hours to dust dry. Let the previous coat dry to a 10 12% moisture ratio prior to subsequent finishing. Frozen finish that has thawed can result in problems with air bubbles in the finish. WATERBASED FINISHES 5
MIXIT Just MIXIT to match the colour of the wood! 1-component binder to be mixed with sanding dust to provide a filling mixture. MIXIT has good filling properties, minimal shrinking and cracking, drys fast and is easy to sand. WOOD FILLER 1-component ready-mixed filler with excellent adhesion is easy to sand, dries like hardwood and can be sawed, sanded, drilled, stained, painted, finished, lacquered and shellacked. Coverage: for filling gaps, cracks or joints up to max. 3 mm prior to application of Synteko finishes or oils. 8-12 m²/l Approx. 60 minutes Flexible stainless steel spatula 250-300 mm width 12 months in unopened container Colours: Coverage: for filling of joints up to 1,5 mm prior to application of Synteko finishes or oils. exotic, light wood, white oak 8 m²/ L 20-30 minutes Flexible stainless steel spatula 250-300 mm width 12 months in unopened container WATERBASED FINISHES / FILLERS 1L 1690 4740182710255 Colour Exotic 5L 1691 7391306105623 Light Wood 5L 1693 7391306090258 White Oak 5L 1694 7391306090165 WATERBASED FINISHES / FILLERS 6 7
SEALMASTER SEALER 1-component fast drying sealer for applicator or roller application, reduces the risk of discoloration, side bonding, is easy to sand and has low grain rise. SEALMASTER can be used on levelling compounds prior Synteko COMBI UV-FIT finish. 1-component fast drying sealer for stainless steel trowel application, seals the wood with very low grain raise and reduces the risk of discoloration and side bonding. Number of coats: 3 coats, intermediate sanding not necessary Number of coats: 1-2 coats, intermediate sanding necessary Coverage: 10-20 m²/l, depending on tools and wood species. 6-8 m²/l on levelling compound 60 to 90 minutes each coat on wooden and parquet floors Approx. 2 hours on levelling compounds Coverage: 20-30 m²/ L 15-20 minutes for each coat Flexible stainless steel spatula 250-300 mm width 12 months in unopened container Applicator with mohair felt approx. 3-5 mm pile high 300-500 mm width roller with approx. 3-5 mm pile high If using SEALMASTER before COMBI UV-FIT a roller or applicator with pile height of 5-8mm 12 months in unopened container WATERBASED FINISHES / SEALERS 1L 1600 7391306101397 5L 1600 7311980122907 10L 1600 7311980124307 5L 1601 7311980112298 10L 1601 7311980124314 WATERBASED FINISHES / SEALERS 8 9
BASIC Good quality 1-component floor finish with very good resistance to grease, water, alcohol and household chemicals. PRO Durable 1-component floor finish with very good resistance to grease, water, alcohol and household chemicals. for normal wear in residential areas Gloss: matt 20, semi-gloss 45 Coverage: 8-15 m²/ L 4-6 hours for each coat Roller ca. 300 mm with 6-8 mm pile high Applicator with mohair felt 300-500 mm with pile high ca. 6 mm 12 months in unopened container for normal to heavy wear in residential areas like living room, kitchen, hall, etc. Gloss: matt 20, semi-gloss 45, gloss 90 Coverage: 8-15 m²/ L 4-6 hours for each coat Roller ca. 300 mm with 6-8 mm pile high Applicator with mohair felt 300-500 mm with pile high ca. 6 mm 12 months in unopened container WATERBASED FINISHES / TOP COATS Gloss BASIC 20 5L 1622 4740182702212 BASIC 20 10L 1622 7391306101243 BASIC 45 5L 1623 4740182702229 BASIC 45 10L 1623 7311980133378 Gloss PRO 20 1L 1625 7391306096693 PRO 20 5L 1625 7391306096709 PRO 20 10L 1625 7391306096716 PRO 45 1L 1626 7391306096723 PRO 45 5L 1626 7391306096730 PRO 45 10L 1626 7391306096747 PRO 90 1L 1627 7391306096754 PRO 90 5L 1627 7391306096761 PRO 90 10L 1627 7391306096778 10 11 WATERBASED FINISHES / TOP COATS
TOP 5 Strong and durable extra matt 1-component floor finish with excellent wear resistance and resistance to grease, water, alcohol and household chemicals. TOP Strong and durable 1-component floor finish with excellent wear resistance and resistance to grease, water, alcohol and household chemicals. for heavy wear in residential areas and offices for heavy wear in residential areas and offices Gloss: extra matt 5 Gloss: matt 20, semi-gloss 45, gloss 90 Coverage: 8-15 m²/ L Coverage: 8-15 m²/ L 4-6 hours for each coat 4-6 hours for each coat Roller ca. 300 mm with 6-8 mm pile high Applicator with mohair felt 300-500 mm with pile high ca. 6 mm Roller ca. 300 mm with 6-8 mm pile high Applicator with mohair felt 300-500 mm with pile high ca. 6 mm 12 months in unopened container 12 months in unopened container WATERBASED FINISHES / TOP COATS Gloss TOP 5 5L 1607 4740182709624 Gloss Product code Package size EAN TOP 20 1604 5L 4740182708825 TOP 45 1605 5L 4740182708870 TOP 90 1606 5L 4740182708887 WATERBASED FINISHES / TOP COATS 12 13
NovaBEST STAR 2-component floor finish for use in areas where high resistance is needed, finished surface is highly slip-resistant as well as good chemical and scratch resistance. The product has longer time to overlapping in difficult conditions. 2-component floor finish with maximum resistance to wear, scratching, scuffing, marring and chemicals. for high traffic areas like offices, public areas, stores, waiting halls, customer service areas etc. for use on high-traffic areas like waiting zones, public spaces and shops. etc.. Gloss: matt 20, semi-gloss 45, gloss 90 Coverage: 8 15 m²/l 4-6 hours for each coat Roller ca. 300 mm with 6-8 mm pile high Applicator with mohair felt 300-500 mm with pile high ca. 6 mm +10 C... +30 C (+50 F +86 F) Gloss: matt 20, semi-gloss 45, gloss 90 Coverage: 8-15 m²/ L 4-6 hours for each coat Roller ca. 300 mm with 6-8 mm pile high Applicator with mohair felt 300-500 mm with pile high ca. 6 mm 12 months in unopened container 12 months in unopened container WATERBASED FINISHES / TOP COATS Gloss Package size* Product code EAN NovaBEST 20 5L 1638 4740182719166 NovaBEST 45 5L 1639 4740182719173 NovaBEST 90 5L 1640 4740182719180 * The finish and the hardener packaged in a cardboard box. Gloss Package size* Product code EAN STAR 20 5L 1628 4740182708818 STAR 45 5L 1629 4740182708856 STAR 90 5L 1630 4740182708863 * The finish and the hardener packaged in a cardboard box. WATERBASED FINISHES / TOP COATS 14 15
Synteko SPORT TEAM 4 2 3 1 1. layer SEALMASTER (or SEALER) 1-component fast drying sealers for applicator, roller or stainless steel trowel application. 2. layer SPORT 90 2-component finish with extreamly good slip resistance (meets DIN norm 18 032:2) and maximum wear resistance. 3. layer waterbased alkyd paint for marking lines and courts 4. layer SPORT 90 again For daily regular cleaning and special maintenance REMOVER Basic detergent which removes dirt and soils from surface. SPORT The winning formula! 2-component finish with extremely good slip resistance (meets DIN norm 18 032:2), maximum resistance to wear and excellent resistance to scratching and marring, liquids and chemicals. ideal for surfaces in sports halls subjected to very heavy wear Gloss: gloss 90 Coverage: 8-15 m²/ L 4-6 hours for each coat Roller ca. 300 mm with 6-8 mm pile high Applicator with mohair felt 300-500 mm with pile high ca. 6 mm 12 months in unopened container WATERBASED FINISHES / SPORT TEAM Green RAL 6018 4740182004880 White (base) 4740182710347 Light Blue RAL 5012 4740182713157 Yellow RAL 1004 4740182004927 Blue RAL 5005 4740182004873 Orange RAL 2008 4740182004897 Black RAL 9005 4740182004866 Red RAL 3000 4740182004934 Gloss SPORT 90 5L 1632 4740182710323 * The finish and the hardener are packaged in a cardboard box. 16 17 WATERBASED FINISHES / SPORT TEAM
Finish in time! Synteko UV-finishes for parquet floors, levelling compounds and design vinyl coverings. For the first time the new Synteko product range also includes finishes for floors levelled with cement or gypsum-based compounds and luxury vinyl tiles, increasing durability of the floors, prolonging their service life and providing a more environmentally friendly and affordable solution. Advantages The floor can be used immediately after the last finishing layer is cured. WOOD UV-FIT The service life of the floors is increased, since the surface is stronger and more resistant. Environmentally friendly protection of surfaces levelled with floor levelling compounds. The floor joints are protected. Prolongs the service life of vinyl floors by protecting the sensitive top layer and joints. The floor can be used immediately after the last finishing layer is cured! UV-curing 1-component floor finish which is extremely resistant to wear and also less sensitive to water, alcohol and household chemicals, protects against scratches. For sealing Synteko SEALMASTER can be used. For cleaning the floor Synteko maintenance products may be used. to be used on all wooden and parquet floors in areas with very high traffic It is easy to be fast Gloss: matte 20, semi-gloss 45, gloss 90 Coverage: 8 15 m²/l 1. layer: PARQUET: LEVELLED FLOOR: DESIGN VINYL: SEALMASTER + drying 1.5 h + intermediate sanding SEALMASTER + drying 1.5 h COMBI UV-FIT + drying 2 h + UV curing 2-4 hours for each coat Applicator with mohair felt. Approx. 5-8 mm pile high 300-500 mm width Roller with synthetic material approx 5-8 mm pile high +10 C... +30 C (+50 F +86 F) 12 months in unopened container WATERBASED FINISHES / UV - FIT 2. layer: 3. layer: WOOD UV-FIT + drying 2 h + UV curing + intermediate sanding WOOD UV-FIT + drying 2 h + UV curing COMBI UV-FIT + drying 3 h + UV curing COMBI UV-FIT + drying 3 h + UV curing COMBI UV-FIT + drying 2 h + UV curing Gloss WOOD UV-FIT 20 5L 1649 4740182719784 WOOD UV-FIT 45 5L 1650 4740182719791 WOOD UV-FIT 90 5L 1651 4740182719807 WATERBASED FINISHES / UV - FIT 18 19
COMBI UV-FIT The floor can be used immediately after the last finishing layer is cured! UV-curing 1-component floor finish, extremely resistant to wear and also less sensitive to water, alcohol and household chemicals, protects against scratches, for finishing levelled floors and design vinyl coverings. for finishing concrete floors covered with cementor gypsum-based levelling compounds and luxury vinyl tiles Gloss: semi-gloss 45 Coverage: 6-12 m²/l 2-4 hours for each coat Applicator with mohair felt. Approx. 5-8 mm pile high 300-500 mm width Roller with synthetic material approx 5-8 mm pile high +10 C... +30 C (+50 F +86 F) 12 months in unopened container UV machinery: floormate + handmate Compact design Maneuverable (0 turn radius) Instant dimming function for immediate full power Can be used with single-phase power (no three-phase power required) Height-adjustable lamp Ozone-free Equipped with corner detection - UV is turned off automatically when tilted more than 25 UV lamp will go into dimming mode when not used and will shut off automatically Includes the latest UV-technologies WATERBASED FINISHES / UV - FIT Gloss COMBI UV-FIT 45 5L 1652 4740182719814 Safety Working with UV is safe if you are following safety instructions. Try to avoid as much as possible direct UV exposure and UV reflection. Always wear skin protection: Protective overall Leather gloves facial shield. www.decorad.com 20 21 WATERBASED FINISHES/ UV-FIT
SOLVENTBASED FINISHES If you want your floor to have a traditional look you should apply a solventbased finish. It is undisputed that solventbased finishes give floors a high quality surface, and add that warm, classic touch. Synteko solventbased finishes can be applied directly on untreated or previously finished hardwood and parquet surfaces. BEFORE USING THE FLOOR The floor can be used with caution 24 hours after the last coat is applied. Furniture can be placed after 24 hours. Allow the moisture to evaporate for one week before laying rugs. Final curing of surface after 2 weeks. Do not clean floor with water or detergents during the first month. Attach felt pads to the legs of chairs and tables in order to avoid scratching the finish. The surface must not be covered with non-porous protective materials. URETHANE Durable 1-component floor finish for soft- and hardwood floors, can be used to recoat itself and most others oil modified urethanes. domestic area Gloss: matt 20, semi-gloss 45, gloss 90 Coverage: 7-15 m²/ L Recoatable after ca. 10 hours Mohair felt applicator ca. 300-500 mm with 5 mm pile high Mohair roller ca. 300 mm with 5 mm pile high Not sensitive to freezing 24 months in unopened container SOLVENTBASED FINISHES PLEASE NOTE! Do not use solventborne finshes for recoating of waterborne finishes. Oily and resinous wood species such as teak should be coated immediately after machine sanding. All finishes should be shaken before use. Do this before vacuuming so that the air mixed into the finish during shaking has a few minutes to escape before use. NB! Detailed information and instructions are provided on the Pro duct Information sheet and MSDS (Material Safety Data Sheet). This document only presents a selection of key information. Gloss URETHANE 20 1L 1664 7391306093869 URETHANE 20 5L 1664 7391306100369 URETHANE 20 10L 1664 7311980125687 URETHANE 45 1L 1665 7391306093876 URETHANE 45 5L 1665 7391306100376 URETHANE 45 10L 1665 7311980125694 URETHANE 90 1L 1666 7391306093883 URETHANE 90 5L 1666 7391306100383 URETHANE 90 10L 1666 7311980125700 22 23 SOLVENTBASED FINISHES / TOP COATS
CLASSIC 2-component acid-curing fast drying floor finish with maximum resistance to wear, scratching, scuffing, marring and chemicals for high traffic areas like offices, public areas, stores, waiting halls, customer service areas etc. Gloss: semi-matt 35, semi-gloss 50, gloss 90 Coverage: 7-15 m²/ L 1,5 hours first coat, 2-3 hours second coat Mohair felt applicator ca. 300-500 mm with 5 mm pile high Mohair roller ca. 300 mm with 5 mm pile high Not sensitive to freezing 24 months in unopened container OILS A wooden floor treated with oil gives a warm impression and exc lu sive feeling of natural wood. The oil penetrates the surface and enhances the colour and lustre of the wood. The surface becomes very durable and is thus suitable for heavy traffic areas. If maintained properly, the oil treated floor will become more wear resistant and beautiful for each year that goes by and you will never have to sand your floor back to the bare wood again. Synteko floor oils have very good wear resistance, are ready to use, not -yellowing and low- odour. They all can be tinted with Synteko TINTING PASTE. BEFORE USING OILED FLOOR Wait for 3 days before laying rugs or carpets and do not use vapour-proof, non-skid underlays or other coverings. Do not wet a floor treated with Synteko floor oils during the first week. Do not use vapour proof, non-skid underlayments or other coverings. Attach felt pads to the legs of chairs and tables in order to avoid scratching the finish. Gloss Package size* Product code EAN SOLVENTBASED FINISHES / TOP COATS CLASSIC 35 1L 1636 7311980124376 CLASSIC 35 5L 1636 7311980124154 CLASSIC 35 16.5L 1636 7311980124161 CLASSIC 50 1L 1637 7311980124352 CLASSIC 50 5L 1637 7311980124192 CLASSIC 50 16.5L 1637 7311980124208 CLASSIC 90 1L 1646 7311980124369 CLASSIC 90 5L 1646 7311980124178 CLASSIC 90 16.5L 1646 7311980124185 *1 L and 5 L finish with hardener in cardboard box, 16.5 L package contains finish with hardener. NB! Detailed information and instructions are provided on the Product Information sheet and MSDS (Material Safety Data Sheet). This document only presents a selection of key information. 24 25 FLOOR OILS
PLEASE NOTE! During use, the oil should be at room temperature. The floor temperature should be between 20 C and 25 C (68 F and 77 F). The moisture content of the wood should be between 5% and 12%. Shake the can carefully before and during use. Do not apply areas larger than 25 m² at a time (10 m² at a time in good drying conditions). Do not allow unabsorbed oil to dry! Dried unabsorbed oil produces glossy spots on the surface. Too much oil will result in a longer drying time and longer time for over-coating. On wood with low absorption, leave some areas untreated during the first application. These areas will be filled during the redistribution procedure. The oxygen curing process will be extremely slow if the temperature is below 18 C. Floor heating system must be turned on during application and polishing. Do not polish the surface while warm so as to avoid bleeding back of the oil. When the finish is dried the room can be aired. Be sure to start regular maintenance before the surface is worn through to bare wood. HARDWAX OIL A solvent-free hardwax-oil with very good coverage and filling properties, based on vegetable raw materials, that makes the parquet and wooden floors more resistant to wear, slipping and liquids (anti-slip class R10 according DIN 51130). It is a 1 - day system: apply today, use the floor with caution tomorrow. Coverage: all heavy traffic areas, like office, stores, public areas, etc. 15-60 m²/ L 12 hours Oil applicator (rubber) ca. 300-500 mm width Buffing machine (2 adjustments, 150 and 300 r.p.m., if possible) Red pads (1pcs/ 20m 2 ) Non-flocculent textiles for polishing (3pcs/ 20m 2 ) 36 months in unopened container NB! Place all organic materials like cloth in a metal container filled with water for at least 16 hours to avoid self-combustion. Dispose of them according to regulations. 1L 1635 4740182722746 5L 1635 4740182722753 FLOOR OILS FLOOR OILS 26 27
NATURAL A high solid, faintly smelling floor oil with very good coverage and excellent properties. NATURAL oil can be recoated with Synteko s waterbased top coats in order to colour of finished floor, also to enhance colouring of exotic woods and to reduce discolouring of waterborne finishes. Coverage: all heavy traffic areas, like office, stores, public areas, etc. 15-60 m²/ L 16 hours Oil applicator (rubber) ca. 300-500 mm width Buffing machine (2 adjustments, 150 and 300 r.p.m., if possible) Red pads (1pcs/ 20m 2 ) Non-flocculent textiles for polishing (3pcs/ 20m 2 ) 24 months in unopened container DOMO An alkyd based low solid oil with very good properties, applicable also with roller Coverage: domestic 10-30 m²/ L 16 hours Oil applicator (rubber) ca. 300-500 mm width or flexible stainless steel spatula 250-300 mm width Buffing machine (2 adjustments, 150 and 300 r.p.m., if possible) Red pads (1pcs/ 20m 2 ) Non-flocculent textiles for polishing (3pcs/ 20m 2 ) 24 months in unopened container 1L 1608 4740182708153 5L 1608 4740182708160 5L 1619 4740182710316 FLOOR OILS FLOOR OILS 28 29
RE-COVER Oxygen curing, faintly smelling maintenance oil Coverage: for periodic maintenance of floors treated with Synteko floor oils 50-100 m²/ L 2-4 hours Oil applicator (rubber) ca. 300-500 mm width or flexible stainless steel spatula 250-300 mm width Buffing machine (2 adjustments, 150 and 300 r.p.m., if possible) Red pads (1pcs/ 20m 2 ) Non-flocculent textiles for polishing (3pcs/ 20m 2 ) 24 months in unopened container DECK OIL A decking oil for basic treatment of new and previously oiled wooden terraces, balconies and other wooden surfaces outside areas. The oil is based on vegetable raw materials, that makes the surface more resistant to wear, slipping and liquids (antislip class R10 according DIN 51130). DECK OIL is suitable for thermal-treated wood, needs no priming, contains UV-protection and does not form a film on surface. Coverage: for basic treatment of wooden terraces and balconies for outdoor use. 15-20 m²/ L 16 hours Wide brush or mohair roller Non-flocculent textiles for polishing (3pcs/ 20m 2 ) 24 months in unopened container 1L 1620 7391306090653 1L 1641 4740182723637 5L 1641 4740182723644 FLOOR OILS FLOOR OILS 30 31
TINTING PASTE A tinting paste for colouring of all Synteko floor oils MAINTENANCE AND CARE Maintaining of wooden floors is an investment. Regular maintenance with the right products gives your floor long life. Synteko offers a complete range of maintenance products for both finished and oiled floors. Surfaces treated with Synteko products are easy to keep clean. Usage: 1 tube (100ml) TINTING PASTE to 1 L of Synteko floor oils 24 months in unopened tube Finished floors Oiled floors Regular SUPER CLEAN SOAP Periodic NEWSHINE RE-COVER Special REMOVER REMOVER Mahogany Ebenholz Teak Olive Rose Wood Steel Blue White Wood FLOOR OILS Colour Ebenholz 100ml 1675 7311980132241 Mahogany 100ml 1675 7311980132272 Olive 100ml 1675 7311980132296 Rose Wood 100ml 1675 7311980132265 Steel Blue 100ml 1675 7311980132289 Teak 100ml 1675 7311980132258 White Wood 100ml 1675 7311980132234 NB! Detailed information and instructions are provided on the Product Information sheet and MSDS (Material Safety Data Sheet). This document only presents a selection of key information. 32 33 MAINTENANCE AND CARE
SUPER CLEAN Wax-free combined cleaning and care agent with a high cleaning effect and an adapted care effect. It leaves the cleaned surface with a thin, matte, lime-free, nonskid, antistatic film which is dissolved and renewed the next time the floor is washed. The film improves the wear resistance of the finish and keeps your floor looking beautiful. for regular cleaning of finished surfaces, also suitable even for clinker and stone floors. ph: ca. 9 36 months in unopened container 1L 1697 7391306088155 5L 1697 4740182709648 NEWSHINE Waterbased and practically odourless maintenance product for sheen refreshing which also protects the floor in high traffic areas and can be used to repair light scratches. for periodic use for finished floors ph: ca. 8,5 Coverage: 50 m²/ L ca. 30 minutes Gloss: semi-gloss (50) 36 months in unopened container 1L 1696 7311980122792 SOAP Floor soap REMOVER Basic detergent which removes dirt and soils from surface. Wax on a oiled surface CANNOT be removed with Synteko REMOVER. MAINTENANCE AND CARE for regular cleaning of wooden floors treated with Synteko floor oils, can also be used for cleaning and maintenance of natural stone. ph: ca. 9 36 months in unopened container 1L 1617 7311980122761 to be used before sanding and recoating with Synteko floor finishes and oils or new treatment with Synteko maintenance products. ph: ca. 11 36 months in unopened container 1L 1692 7391306102790 5L 1617 7311980119563 34 35 MAINTENANCE AND CARE
SPECIAL PRODUCTS RETARDER A mixture of solvents to be added to Synteko CLASSIC in order to delay drying process. Not sensitive to freezing 24 months in unopened container LUT Bleaching agent for treatment of solid, freshly sanded indoor pine and spruce floors. The lye prevents the wood from yellowing and keeps it light for many years. 1L 1670 4740182702502 A rea of use: for treatment of solid, freshly sanded indoor pine and spruce floors ph: ca. 13 Coverage: 8 m²/ L 12 hours 24 months +10 C... +30 C (+50 F +86 F) ROLLER Roller for application of Synteko waterbased top finishes 1L 1616 7311980122754 Size: for application of Synteko BASIC, PRO, TOP, NovaBEST, STAR, SPORT, WOOD UV-FIT, COMBI UV- FIT ca. 250mm with pile high ca. 7mm SPECIAL PRODUCTS NB! Detailed information and instructions are provided on the Product Information sheet and MSDS (Material Safety Data Sheet). This document only presents a selection of key information. Measurments EAN 250 mm 4013307448563 SPECIAL PRODUCTS 36 37
TECHNICAL FAQ TECHNICAL FAQ / First Coat FAQ Causes Corrective actions Sand back to bare wood. Apply the first two coats wet to wet and keep the finish in motion when applying the initial coat without going all the way to the wall. Uneven applicator finishing; finish has had time to dry between first and second applications. Visible applicator strokes, uneven colour after application of SEALER. Sand back to bare wood and re-finish. Poured finish has remained on the floor too long. The wood is absorbing excessive moisture and the finish is drying more slowly over these surfaces. Round, dark, miss-colourations approximately 20 40 cm in diameter. Sand to bare wood and re-finish. Dark, narrow lines/scratches. Sanding scratches from coarse-grade sandpaper have not been sanded away; these absorb more finish and the colour darkens. Sand to bare wood and remove all white from the joint. Cellulose finish mixed with sanding dust has been used for filling. Finish has been applied before this has dried. White in joint between staves or boards. Remove the floor and relay it. Use correct finish for first sealer coat. The wrong type of finish has been used for the initial coat (adhesive properties are too good) and the wood has shrunk. Edge-gluing. The floor is without joints between boards, with the exception of some areas where the joints are very wide. Sand to bare wood and re-finish. Light areas after roller application. Too much air has worked into the lacquer and late overlapping. Excessively thick initial sealer coat has been applied. Perform a thorough intermediate sanding with used 120-grade paper or screen. Also flatten the surface gloss with an abrasive (maroon) pad. Course appearance, excessive grain raise, roller patterns, etc. Sand to bare wood and re-finish. Darker wood along the walls. Excessively thick application with brush along the walls and/or brush application have begun to dry before overlapping with a roller. 38 39 TECHNICAL FAQ / Second or Final Coating FAQ Causes Corrective actions Sand away the bubbles away entirely with used 120 or 150-grade sandpaper and re-finish. Draft across finish surface. Rolling too quickly. Fast drying. Low relative humidity. Frozen finish or stored in low temperature for a longer period. Bubbles/Blisters in the surface. If heavy bubbles sand back to bare wood. Sand away with 150-grade sandpaper and re-finish. Dust particles, dusty workplace, poor vacuuming. Unclean tools, bad mixing hardener. Particles in the surface. Sand back to bare wood. Avoid contamination from adjoining surfaces. Re-finish. Silicone problem. Silicone contamination. Contamination of surfaces or tools. Shrinkage/Fish eyes/creeping Sand the surface to an even gloss with 150-grade sandpaper or screen. Also flatten the surface gloss with an abrasive (maroon) pad. Container not agitated. Uneven application. Uneven drying. Uneven gloss Contaminated surface, Silicon on surface, grease on surface Peeling/Bad adhesion Sand back to bare wood. If heavy marks sand back to bare wood. If just small marks sand with 150-grade paper or screen. Also flatten the surface gloss with an abrasive (maroon) pad. Cold finish, cold floor. Mixing two brands. Bad levelling, brush marks or roller structure in the surface. Sand back to bare wood. Too long drying time, too high humidity, too cold floor or water leaking out from the inside of the roller. Alligatoring, surface looks like the skin of an alligator. Room temperature at least 13 C, relative air humidity not over 80%. Good ventilation (not draught). High humidity, low temperature, too heavy (thick) coats or no air movements. Bad drying TECHNICAL FAQ
Finishing a wooden floor is not an assembly line job. Each floor is unique when it comes to appearance, condition, type of wood, etc. Each environment in which a floor is situated is also unique in respect to varying wear and the effects of everyday chemicals of different kinds. Temperature and humidity are other factors that can vary a great deal from one job to another. Choice of products and handling of the products must be changed according to the present situation. Synteko supports professionals treating wooden floors (finishing, oiling, cleaning and maintenance). Synteko s brand is oriented to a contractor who needs highquality finishing products and appreciates easy handling, good durability, natural look of the wooden floor, and stable product quality. We are constantly keeping track of market trends and the needs of our customers, and our development group is always busy developing new products. Synteko production is certified in accordance with the International Standard Organization s ISO 9001 regarding quality management standards. www.synteko.com 2016 Synteko is a brand of the SIKA Group