Table I Table II IP x x IP Ratings Guide The IP classification system designates the degree of protection provided by an enclosure against solid objects or water ingress. Table I shows degrees of protection against solid objects, Table II shows degrees of protection against water. PROTECTION CLASS MECHANICAL IMPACT RESISTANCE Ex) IK 08 Table I (st characteristic numeral) Degree of against solid objects Digit 0 Non-protected Table II (2nd characteristic numeral) Degree of against water Digit 0 Non-protected IK CODE MECHANICAL IMPACT RESISTANCE 00 Unprotected 200g 0 7.5cm Impact = 0.5 joule Protected against a solid object greater than 50mm, such as a hand. 2 Protected against dripping water. 2 02 200g 0cm Impact = 0.20 joule >2.5mm >.0mm Protected against a solid object greater than 2.5mm, such as a finger. 3 Protected against a solid object greater than 2.5mm, such as wire or a tool. 4 Protected against a solid object greater than.0mm, such as wire or thin strips. 5 Protected against dripping water when tilted up to5º. 3 Protected against spraying water at an angle of up to 60º. 4 Protected against splashing water from any direction. 5 03 04 05 200g 7.5cm 200g 25cm 200g 35cm Impact = 0.35 joule Impact = 0.50 joule Impact = 0.70 joule 500g 06 20cm Impact = joule Dust-protected. Prevents ingress of dust sufficient to cause harm. 6 Protected against jets of water from any direction. 6 07 500g 40cm Impact = 2 joule Dust tight. No ingress of dust. Protected against heavy seas or powerful jets of water. Prevents ingress sufficient to cause harm. 7 08.7kg 29.5cm Impact = 5 joule Protected against the effects of temporary immersion in water. 8 Protected against the effects of continuous immersion in water. 09 0 5kg 20cm 5kg 40cm Impact = 0 joule Impact = 20 joule
Vandal Resistant Pilot Lamp Φ8mm 2mm Brass 8-P-N-D-G Series Illuminated Options 8-P-N-D-G S8 (8mm) S2 (2mm) P- Pin (.8x0.4) N- Nickel plated brass D- W- White Y- Yellow B- Blue G- Green R- Red O- Orange 6V 2V 24V Dielectric Strengh Lampshade Life Pin(.8X0.4) 00VAC 5~4Nm IP65/ IK09 PC Nickel plated brass/ Chrome plated brass S8 6V/ 2V/ 24V R G Y O B W Approx. 40, 000hours Note: Additional voltage available upon request. Please ask your salesperson. S2 0.059 (.5) 0.59 (5.0) 0.059 (.5) 0.433 (.0).063 (27.0) 0.394 (0.0).004 (25.5) 0.394 (0.0) 0.04 (2.65) 0.472 (2.0x.0) 0.04 (2.65) 0.97 (8.0) 0.35 (8.0x0.75) 0.862 (2.9) 0.38 (3.5) S2 S8
Φ2mm 2-F-A-G Square and Round version available,000,000 cycles momentary 2-F-P-A-BK 2-B-S Momentary: Means that when you push switch and then move your finger, the actuator will back to the original position. 2-B-A-G 2-B-A-W 2-B-A-B 2-B-A-B ) Series Options Function Non-illumainted B- Round P- Pin (2.0x0.5) Momentary no letter S- Stainless Steel F- Square Screw blank - NO N- Nickel plated brass A- Zin- Al Alloy Black ) The color only Zin-Al alloy material available BK- Black W- White Y- Yellow B- Blue G- Green R- Red O- Orange Function (NO) 0.472 (2.0) 0.472 (2.0) 0.689 (7.5) Max. Panel Thickness: 0.236 (6.0mm) M2X.0 0.079 (2.0) 0.626 (5.9) 0.55 (4.0) Illuminated Options Front Shape Max. Switch Rating Contact Resistance Insulation Resistance Dielectric Strengh Contact Operation Pressure 2-B/S 2-B/A 2-F/A Non-illuminated Round Square Screw/ Pin(2.0X0.5) 2A 48VDC 50m 000m 2000VAC,000,000cycles 5~4Nm 5N IP65 Stainless Steel/ Brass/ Stainless Steel/ Brass/ Zin-Al Alloy Finish R G Y O B W BK 0.287 (7.3) 0.20 (5.) 0.339 (8.6) 0.472 (2.0) 0.287 (7.3) 0.20 (5.) 0.339 (8.6) 0.472 (2.0) Screw 0.54 (3.9) 0.465 (.8) 0.256 (6.5) 0.465 (.8) Solder
Φ6mm Normal Open Domed/ Flat/ High Flat Front Stainless Steel/ Brass,000,000 cycles momentary Momentary: Means that when you push switch and then move your finger, the actuator will back to the original position. Function 0.630 (6.0) Max. Panel Thickness: 0.236 (6mm) 0.8 (3.0) 6-H--S 6-B--G M6X.0 0.472 (2.0) 0.709 (8.0) 0.858 (2.8) 0.748 (9.0) Marking Series Options Function Finish Options F - Flat P- Pin(2.8x0.5) H - High Screw blank B - Domed Front Shape Max. Switch Rating Contact Resistance Insulation Resistance Dielectric Strengh Contact Operation Pressure * can be customized. Flat Momentary: G- *Gold - NO N- Nickel 2- NC A- *Anodized aluminum S- Stainless Steel B- Brushed P- Polished Rotation blank Screw/ Pin(2.8X0.5) 2A 48VDC 50m 000m 2000VAC,000,000cycles 5~4Nm 5.5N IP65/ IK09 Domed (NO) 6-F 6-B 6-H High Flat Stainless Steel/ *Gold plated Brass/ *Anodized Aluminum Stainless Steel/ Nickel plated brass/ *Gold plated Brass/ *Anodized Aluminum 2 (NC) 0.55 (4.0) 0.748 (9.0) 0.55 (4.0) 0.748 (9.0) 0.55 (4.0) 0.748 (9.0) Screw 0.22 (3.) 0.244 (6.2) 0.622 (5.8) 0.22 (3.) 0.244 (6.2) 0.622 (5.8) 0.079(2.0) 0.244 (6.2) 0.622 (5.8) 0.256 (6.5) 6-H 6-B 6-F 0.55 (4.0) 0.748 (9.0) 0.55 (4.0) 0.748 (9.0) 0.55 (4.0) 0.748 (9.0) Solder 0.22 (3.) 0.22 (3.) 0.079(2.0) 8.5 0.335 (8.5) 0.335 (8.5) 0.335 (8.5) 0.622 (5.8) 0.622 (5.8) 0.622 (5.8) 2.8 6-H/P 6-B/P 6-F/P
Φ9mm Normal Open/ Normal Closed Domed/ Flat/ High Flat Front Stainless Steel/ Brass,000,000 cycles momentary Momentary: Means that when you push switch and then move your finger, the actuator will back to the original position. 9-B--G Marking Series Options Function Finish Options Function 9-H--S 9 F- Flat P- Pin(2.8x0.5) H- High Screw blank B- Domed Momentary: - NO G- *Gold N- Nickel A- *Anodized aluminum S- Stainless Steel B- Brushed P- Polished Rotation blank (NO) 0.8 (3.0) 0.59 (5.0) Max. Panel Thickness: 0.35 (8mm) M9X.0 0.748 (9.00).000 (25.4) Front Shape Max. Switch Rating Contact Resistance Insulation Resistance Dielectric Strengh Contact Operation Pressure * can be customized. 9-F 9-B 9-H Flat Domed High Flat Screw/ Pin(2.8X0.5) 2A 48VDC 50m 000m 2000VAC,000,000cycles 5~4Nm 5.5N IP65/ IK09 Stainless Steel/ Nickel plated brass/ *Gold plated Brass/ *Anodized Aluminum Stainless Steel/ Nickel plated brass/ *Gold plated Brass/ *Anodized Aluminum 0.709 (8.0) 0.709 (8.0) 0.709 (8.0) Screw 0.53 (3.9) 0.744 (8.9) 0.099 (2.5) 0.744 (8.9) 0.42 (3.6) 0.744 (8.9) 0.709 (8.0) 0.709 (8.0) 0.709 (8.0) 0.256 (6.5) 9-H 9-F 9-B Solder 0.53 (3.9) 0.099 (2.5) 0.42 (3.6).3 0.744 (8.9) 0.744 (8.9) 0.744 (8.9) 9-H/P 9-F/P 9-B/P 2.8
Φ9mm (Short) Normal Open/ Normal Closed Domed/ Flat/ High Flat Front Stainless Steel/ Brass,000,000 cyles momentary s9-b--s Momentary: Means that when you push switch and then move your finger, the actuator will back to the original position. Function s9-h--s s9-f-p--s Marking Series Options Function Finish Options s9 C F - Flat P- Pin(2.8x0.5) H - High Screw blank B - Domed Momentary: - NO 2- NC G- *Gold N- Nickel A- *Anodized aluminum S- Stainless Steel B- Brushed P- Polished Rotation blank (NO) 2 (NC) 0.59 (5.0) Max. Panel Thickness: 0.236(6mm) 0.8 (3.0) M9X.0 0.748 (9.00).000 (25.4) Options Max. Switch Rating Contact Resistance Insulation Resistance Dielectric Strengh Contact Operation Pressure * can be customized. Flat s9-f s9-b s9-h Screw/ Pin(2.8X0.5) 2A 48VDC 50m 000m 2000VAC,000,000cycles 5~4Nm 5.5N IP65/ IK09 Domed Stainless Steel/ Brass/ *Gold plated Brass Stainless Steel/ Chrome, Nickel plated brass/ *Gold plated Brass High Flat 0.535 (3.6) 0.772 (9.6) 0.535 (3.6) 0.772 (9.6) 0.535 (3.6) 0.772 (9.6) Screw 0.42 (3.6) 0.236 (6.0) 0.744 (8.9) 0.063 (.6) 0.236 (6.0) 0.744 (8.9) 0.42 (3.6) 0.236 (6.0) 0.744 (8.9) 0.528(3.4) 0.787(20.0) 0.528(3.4) 0.787 (20.0) 0.528(3.4) 0.787 (20.0) 0.874 (22.2) 0.256 (6.5) s9-h s9-f s9-b Solder 0.42 (3.6) 0.063 (.6) 0.42 (3.6) 8.20 0.744 (8.9) 0.744 (8.9) 0.744 (8.9) s9-h-p s9-f-p s9-b-p 2.8
Φ22mm Normal Open/ Normal Closed Domed/ Flat/ High Flat Front Stainless Steel/ Brass,000,000 cycles momentary 22-P--S Momentary: Means that when you push switch and then move your finger, the actuator will back to the original position. Function 22-F--S 22-P--S Marking Series Options Function Finish Options F- Flat P- Pin(2.8x0.5) H- High Screw blank B- Domed Momentary: - NO 2- NC S- Stainless Steel (NO) 2 (NC) 0.8 (3.0) 0.709 (8.0) 0.0.984 (25.0) Max. Panel Thickness: 0.35 (8mm) Screw 0.53 (3.9) M22X.0 22-H 0.709 (8.0) 0.866 (22.00).30 (28.7) 0.984 (25.0) 0.862 (2.9) 0.709 (8.0) Front Shape Max. Switch Rating Contact Resistance Insulation Resistance Dielectric Strengh Contact Operation Pressure * can be customized. 0.079 (2.0) Flat Screw/ Pin(2.8X0.5) 2A 48VDC 50m 000m 2000VAC,000,000cycles 5~4Nm 5.5N IP65/ IK09 Stainless Steel Stainless Steel 0.709 (8.0) 0.862 (2.9) 0.709 (8.0) 22-F 22-B 22-H Domed 22-F 22-B 0.42(3.6) High Flat 0.709 (8.0) 0.862 (2.9) 0.709 (8.0) Solder 0.53 (3.9) 0.079 (2.0) 0.42(3.6) 0.862 (2.9) 0.862 (2.9) 0.862 (2.9)
Φ6mm Illuminated and Non-Illuminated Momentary/ Latching T6H-M-S-D-G T6F-M-S Momentary: Means that when you push switch and then move your finger, the actuator will back to the original position. Latching: Means that when you push switch once it will change state and stay in this pushed-down position and will not come back to original position unless you push it again Seriees Options Function Finish Illuminated Options T6F-M-N-R-R T6 F- Flat H- Raised flat Pin(2.8x0.5) blank M- Momentary NONC 2 2NO2NC Z- Latching NONC 2 2NO2NC A- Anodized aluminum N- Nickel plated brass S- Stainless steel P Polished Rotation blank D- R- Non-illuminated blank W- White Y- Yellow B- Blue G- Green R- Red O- Orange 6V 2V 24V 36V 0V 230V Blank IP40 IP65 Max. Panel Thickness: 0.394 (0.0) M9X.0 0.8 (3.0) Operation Description NC C NO NC + NC2 NO NO2 C - C2 0.630 (6.0) 0.457 (.6) 0.709 (8.0) 0.850 (2.6) 0.748 (9.0) Illuminated Options Non-Illuminated Pin(2.8X0.5) Max. Switch Rating 3A 250VAC Contact Resistance 50m Insulation Resistance 000m Dielectric Strengh 2000VAC,000,000cyles 200,000cyles Contact 5~4Nm Operation Pressure 3~5N IP IP40, IP65/ IK09 Stainless Steel/ Nickel Plated Brass/ Anodized Aluminum Stainless Steel/ Nickel Plated Brass/ Anodized Aluminum 6V/ 2V/ 24V/ 36V/ 0V/ 230V R G Y O B W Life Approx. 40, 000hours *Crust material and voltage can be customized. Illuminated Options T6-F T6-F/R T6-F/D 0.465 (.8) 0.645 (6.4).65 (29.4).362 (34.6).409 (35.8) 0.54 (3.9) 0.067 (.7) 0.472 (2.0) Options Illumination s 0.06 (0.4) 0.0 (2.8) 0.626 (5.9) 0.07 (.8) 0.97 (5.0) 0.425 (0.8) 0.54 (3.9) Hight Flat 0.067 (.7) Flat
Φ9mm Illuminated and Non-Illuminated Momentary/ Latching Momentary: Means that when you push switch and then move your finger, the actuator will back to the original position. Latching: Means that when you push switch once it will change state and stay in this pushed-down position and will not come back to original position unless you push it again Illuminated Marking Series Options Function Finish Options Options S9 F- Flat Pin(2.8x0.5) blank M- Momentary S- Stainless Steel D- W- White 6V NONC A- *Anodized Aluminum R- Y- Yellow 2V 2 2NO2NC Non-illuminated blank B- Blue 24V Z- Latching G- Green 36V NONC R- Red 0V 2 2NO2NC O- Orange 230V Max. Panel Thickness: 0.394 (0.0) M9X.0 0.8 (3.0) Operation Description NC C NO NC N C 2 N0 N02 C C 2 0.748 (9.0) 0.60 (5.5) 0.992 (25.20) Illuminated Options Non-Illuminated Pin(2.8X0.5) Max. Switch Rating 5A 250VAC Contact Resistance 50m Insulation Resistance 000m Dielectric Strengh 2000VAC,000,000cycles Contact 5~4Nm Operation Pressure 3~5N IP65/ IK09 6V/ 2V/ 24V/ 36V/ 0V/ 230V R G Y O B W Life Approx. 40, 000hours * and voltage can be customized. S9-F S9-F/R S9A-F/D 0.276 (7.0) 0.528 (3.4) 0.079 (2.0).22 (28.5).496 (38.0).457 (37.0) 0.020 (0.5) 0.02 (2.6) 0.472 (2.0) 0.0 (2.8) 0.97 (5.0) 0.669 (7.0) Size Tolerance: ±0.mm
Φ22mm Illuminated and Non-Illuminated Flat/ Concave Momentary/ Latching Momentary: Means that when you push switch and then move your finger, the actuator will back to the original position. Latching: Means that when you push switch once it will change state and stay in this pushed-down position and will not come back to original position unless you push it again Illuminated Marking Series Options Function Finish Options Options F- Flat Pin(2.8x0.5) blank M- Momentary S- Stainless Steel D- W- White 6V C- *Concave - NONC A- *Anodized Aluminum R- Y- Yellow 2V Z- Latching Non-illuminated blank B- Blue 24V - NONC G- Green 36V R- Red 0V O- Orange 230V Max. Panel Thickness: Momentary Version: 0.35 (8.0) Latching Version: 0.472 (2.0) 0.8 (3.0) Operation 2 3 4 0.266 (22.0) Description NO NC + - NC NO + and - for Lamp M22X.0 0.728 (8.0) 0.976 (24.8).26 (28.6) 0.988 (25.) Illuminated Options Non-Illuminated Pin(2.8X0.5) Max. Switch Rating 5A 250VAC Contact Resistance 50m Insulation Resistance 000m Dielectric Strengh 2000VAC,000,000cycles Contact 5~4Nm Operation Pressure 3~8N IP65 PA 6V/ 2V/ 24V/ 36V/ 0V/ 230V R G Y O B W Life Approx. 40, 000hours * and voltage can be customized. 22-F 22-F/R 22-F/D 0.079 (2.0) 0.673 (7.).004 (25.5).402 (35.6) 0.870 (22.).20 (30.5).606 (40.8) Momentary 0.020 (0.5) 0.535 (3.6) 0.858 (2.8 Latching 0.020 (0.5) 0.535 (3.6) 0.858 (2.8 0.0 (2.8) 0.433 (.0) 0.386 (9.8) 0.543 (3.8)
Φ25mm Illuminated and Non-Illuminated Flat/ Concave Momentary/ Latching Momentary: Means that when you push switch and then move your finger, the actuator will back to the original position. Latching: Means that when you push switch once it will change state and stay in this pushed-down position and will not come back to original position unless you push it again Illuminated Marking Series Options Functiom Finish Options Options F- Flat Pin(2.8x0.5) blank M- Momentary S- Stainless Steel D- W- White 6V C- *Concave - NONC A- *Anodized Aluminum R- Y- Yellow 2V 2-2NO2NC Non-illuminated blank B- Blue 24V Z- Latching G- Green 36V - NONC R- Red 0V 2-2NO2NC O- Orange 230V Max. Panel Thickness: Momentary Version: 0.394 (0.0) Latching Version: 0.472 (2.0) 0.8 (3.0) Operation 2 3 4 0.984 (25.0) Description NO NC + - NC NO + and - for Lamp M25X.0 0.787 (20.0).098 (27.9).358 (34.5) Illuminated Options Non-Illuminated Pin(2.8X0.5) Max. Switch Rating 5A 250VAC Contact Resistance 50m Insulation Resistance 000m Dielectric Strengh 2000VAC,000,000cycles Contact 5~4Nm Operation Pressure 5.5~7N IP65 PA 6V/ 2V/ 24V/ 36V/ 0V/ 230V R G Y O B W Life Approx. 40, 000hours * and voltage can be customized. 25-F 25-F/R 25-F/D 0.386 (9.8) 0.64 (5.6) 0.094 (2.4) 0.744 (8.9).083 (27.5).492 (37.9) 0.843 (2.4).8 (30.0).630 (4.4) 0.020 (0.5) 0.0 (2.8) 0.567 (4.4) 0.0 (2.8) 0.244 (6.2) 0.689 (7.7) 0.980 (24.9) Momentary Latching
Φ 30mm Illuminated and Non-Illuminated Flat/ Concave Momentary/ Latching Momentary: Means that when you push switch and then move your finger, the actuator will back to the original position. Latching: Means that when you push switch once it will change state and stay in this pushed-down position and will not come back to original position unless you push it again Illuminated Marking Series Options Functiom Finish Options Options Max. Panel Thickness: Momentary Version: 0.394 (0.0) Latching Version: 0.472 (2.0) 0.8 (3.0) Operation 2 3 4 0.984 (25.0) Description NO NC + - NC NO + and - for Lamp M30*.0 0.787 (20.0).098 (27.9).358 (34.5) F- Flat Pin(2.8x0.5) blank M- Momentary S- Stainless Steel D- W- White 6V C- *Concave - NONC A- *Anodized Aluminum R- Y- Yellow 2V 2-2NO2NC Non-illuminated blank B- Blue 24V Z- Latching G- Green 36V - NONC R- Red 0V 2-2NO2NC O- Orange 230V 30-F Illuminated Options Non-Illuminated Pin(2.8X0.5) Max. Switch Rating 5A 250VAC Contact Resistance 50m Insulation Resistance 000m Dielectric Strengh 2000VAC,000,000cycles Contact 5~4Nm Operation Pressure 5.5~7N IP65 PA 6V/ 2V/ 24V/ 36V/ 0V/ 230V R G Y O B W Life Approx. 40, 000hours * and voltage can be customized. 30-F/R 30-F/R 30-F/D 0.386 (9.8) 0.64 (5.6)