ISO 9001:2008 Clause 8.5.2 P023 Corrective Action Procedure Document No P023 Corrective Action Procedure.docx Rev 2 Uncontrolled Copy Controlled Copy x Date 01-Jul-2012 COMPANY PROPRIETARY INFORMATION Prior to use, ensure this document is the most recent revision by checking the Master Document List. To request a change, submit a Document Change Request to the Document Control Representative.
Approvals The signatures below certify that this procedure has been reviewed and accepted, and demonstrates that the signatories are aware of all the requirements contained herein and are committed to ensuring their provision. Name Signature Position Date Prepared by Emmy Kerrigan Document Controller Reviewed by Peter English QA Officer Approved by John Smith Owner Amendment Record This procedure reviewed to ensure its continuing relevance to the systems and process that it describes. A record of contextual additions or omissions is given below: Page No. Context Revision Date Document No: P023 Corrective Action Procedure.docx Page 2 of 7
Contents P023 Corrective Action Procedure... 4 1. Introduction & Purpose... 4 2. References... 4 3. Terms & Definitions... 4 4. Application & Scope... 4 5. Requirements... 5 6. Process... 5 6.1 Review Non-conformities... 5 6.2 Determine Causes... 5 6.3 Evaluate Need for Action... 5 6.4 Implement Action... 6 6.5 Verify Effectiveness... 6 6.6 Management Review... 6 6.7 Documentation & Records... 6 6.8 Corrective Action Process Map... 7 Document No: P023 Corrective Action Procedure.docx Page 3 of 7
P023 Corrective Action Procedure 1. Introduction & Purpose The purpose of this procedure is to establish the process for identifying, documenting and implementing corrective actions in order to eliminate actual non-conformances. Babinda Electrics quality management system is geared toward the elimination of defects and to this end; a formal corrective action system is utilized. 2. References Reference Title & Description 8.5.2 Quality System Manual F023-1 Corrective Action Request Form F023-2 Corrective Action Request Log 3. Terms & Definitions Term Non-conformity Preventive Action Corrective Action Definition Non-fulfilment of a requirement Action taken to eliminate a potential non-conformity Action taken to eliminate the cause of a non-conformity 4. Application & Scope This procedure is applicable to all corrective actions related to non-conforming products, services and audit results. Any corrective action taken to eliminate the causes of actual non-conformances is appropriate to the magnitude of the problem whilst also being in proportion to the risks presented by the non-conformance. Root causes of non-conforming products and services, as well as, quality management system defects are investigated and actions implemented to prevent their recurrence. All Major non-conformances raised will be considered by the QA Officer and investigated with the raiser of the nonconformance/rectifier and follow up actions when necessary. This action is to ensure the process has been completed and was suitable. At this time further actions will be considered to correct the process or action which originally caused to non-conformance. Document No: P023 Corrective Action Procedure.docx Page 4 of 7
5. Requirements Staff & Process Owners are required to: Highlight potential non-conformances to their Manager/Supervisor Follow this procedure upon detection of a non-conformance The Quality Management Representative is required to: Determine the causes of non-conformances Maintain a system for reporting and record keeping Business Owners are required to: 6. Process Implement necessary actions to achieve resolution Review the effectiveness of corrective actions taken 6.1 Review Non-conformities Non-conformances or opportunities for improvement may be identified by employees, customer complaints or by quality management system audit reports. By whichever means a non-conformance is identified, the underlying cause of the non-conformance is investigated. Corrective action will be considered proportionately to the non-conformances raised and the impact they have on the organisation performance, meeting of statutory/ regulatory and customer requirements. 6.2 Determine Causes The Quality Management Representative will review any issues raised and complete a non-conformance report F020-1 to identify root cause and level of action required. Repeated non-conformances of the same nature or significant deviations from procedures or the quality policy are reported to Management for action and resolution. 6.3 Evaluate Need for Action A decision as to the suitability of implementing the control measure, compared to the expense or impact on the present operational and efficient systems and practices, will be considered. Where cost is prohibitive yet seriousness dictates an action, it will either be considered at the next management meeting and/or the Proprietor will have the final decision. Where the impact of the non-conformance has minimal effect on the organisation and process no action will be considered as an option. As Customer Satisfaction is paramount for our continued viability and growth, Customer complaints will be considered a high priority ( Note public perception and the possibility of limiting future works should be considered with customer based non-conformances). Customer complaints will be treated, as detailed above with special mention being made at time of Management Review and supervisor meetings. The proprietor will have the ultimate decision on any action instigated and related to customer complaints. If corrective action is necessary then from F023-1 will be developed and appropriate personnel assigned tasks. Document No: P023 Corrective Action Procedure.docx Page 5 of 7
6.4 Implement Action Designated personnel must implement the agreed level of action within an agreed timescale. The Quality Management Representative will follow up all corrective actions to ensure effective and timely responses are achieved. Quality Management Representative will close out the corrective action when satisfactory resolution has been achieved and when objective evidence of close out has been obtained through inquiry or audit. Preventive action such as, implementing, modifying or enforcing procedures or controls will be taken to avoid repetition of the non-conformance where necessary. Follow up times will also be considered and a means of monitoring a successful outcome set where necessary. 6.5 Verify Effectiveness The corrective action request originator verifies the effectiveness of the corrective action(s) taken. Where the originator is also responsible for the implementation of the corrective action, the Quality Management Representative will provide the verification for corrective action request closure. If corrective actions are determined to be not effective, the original corrective action request will be closed and a new corrective action request will be issued. 6.6 Management Review Corrective actions implemented or to be implemented, will be reviewed at supervisory meetings. A review of corrective actions is undertaken by management to verify the performance and effectiveness of corrective actions taken. Corrective actions are reviewed for long-term effects and process improvements in Management Reviews. The Quality Management Representative and management determines if the action taken could potentially improve other areas of the organization. 6.7 Documentation & Records Any changes to the quality management system and its procedures, as a result of corrective actions are recorded. All documentation and records generated by the corrective action process are managed in accordance with ISO 9001:2008 Clauses 4.2.3 & 4.2.4. Document No: P023 Corrective Action Procedure.docx Page 6 of 7
6.8 Corrective Action Process Map Corrective Action Request F023-1 Determine Causes Enter in Corrective Action Request log F023 2 Evaluate Need for Action Devise Action Plan Implement Action Plan Verify NO YES Close-out Corrective Action Request F023-1 Management Review Update Corrective Action Log F023-2 Document No: P023 Corrective Action Procedure.docx Page 7 of 7