UL Evaluation Report UL ER9516-01 Issued: December 9, 2013 Revised: September 29, 2017 Visit UL s On-Line Certifications Directory: www.ul.com/erdirectory for current status of Report. UL Category Code: ULFB CSI MasterFormat DIVISION: 07 00 00 THERML ND MOISTURE PROTECTION Sub-level 2: 07 50 00 Membrane Roofing Sub-level 3: 07 54 00 Thermoplastic Membrane Roofing Sub-level 4: 07 54 23 Thermoplastic-Polyolefin Roofing COMPNY: FIRESTONE BUILDING PRODUCTS CO L L C 200 4 TH VENUE SOUTH NSHVILLE, TN 37201 U (800) 428-4442 www.firestonebpco.com 1. SUBJECT:,, Roofing Membranes 2. SCOPE OF EVLUTION 2015, 2012, 2009, and 2006 International Building Code (IBC) 2015, 2012, 2009, and 2006 International Residential Code (IRC) ICC ES cceptance Criteria for Membrane Roof-Covering Systems (C75), Dated July 2010 ICC ES cceptance Criteria for Quality Documentation (C10), Dated June 2014 The products were evaluated for the following properties: Exterior Fire Exposure Wind Uplift. Resistance Physical Properties Impact Resistance Foot Traffic Resistance
3. REFERENCED DOCUMENTS NSI/UL790, 8 th Ed. (STM E108), Standard Test Methods for Fire Tests of Roof Covering NSI/UL1897, 6 th Ed. Uplift. Tests for Roof Covering Systems FM 4470 (2012), The pproval Standard for Single-Ply, Polymer-Modified Sheet, Built-Up Roof (BUR) and Liquid pplied Roof ssemblies For Use in Class 1 and Noncombustible Roof Construction FM 4474-(h2011), merican National Standard for Evaluating the Simulated Wind Uplift. Resistance of Roof ssemblies Using Static Positive and/or Negative Differential Pressures STM D6878-08, Standard Specification for Thermoplastic Polyolefin Based Sheet Roofing STM G154-06, Standard Practice for Operating Fluorescent Ultraviolet (UV) Lamp pparatus for Exposure of Nonmetallic Materials STM D312-06, Standard Specification for sphalt Used in Roofing ICC ES cceptance Criteria for Membrane Roof-Covering Systems (C75), Dated July 2010 ICC ES cceptance Criteria for Quality Documentation (C10), Dated June 2014 4. USES The single-ply roofing systems covered in this report are used as roof coverings in mechanically fastened or fully adhered Class, B, or C roof assemblies installed on combustible or noncombustible decks. 5. PRODUCT DESCRIPTION 5.1 GENERL The, and Membrane Roofing Systems are single-ply roofing membranes designed to be used in adhered roofing systems or mechanically fastened roofing systems as described in this report. The membranes are provided in rolls of various lengths and widths. The roofing assemblies incorporating the membranes comply with the following properties when installed as described in this report. Fire Classification: Roofing assemblies covered under this report have been tested for fire classification Class, B, or C in accordance with UL 790 (STM E108), as required by Section 1505.1 of the 2015, 2012, 2009 and 2006 IBC and Section R902.1 of the 2015, 2012, 2009 and 2006 IRC. Wind Uplift. Resistance: Roofing assemblies covered under this report have been tested for wind uplift resistance in accordance with FM 4474 or UL1897, and therefor qualify for use under Roofing membranes Section 1504.3.1 of the 2015, 2012, 2009 and 2006 IBC. The roofing assemblies shall be designed to resist the design wind load pressures for components and cladding in accordance with Section 1609 of the 2015, 2012, 2009 and 2006 IBC. Physical Properties: The roofing membranes covered under this Report have been tested for physical properties in accordance with STM D6878 and STM G154, and therefore qualify for use under Section 1507.13.2 and Section 1504.6 of the 2015, 2012, 2009 and 2006 IBC. Impact Test: Firestone single ply membranes covered under this Report have been tested for impact resistance in accordance with Resistance to Foot Traffic Test in Section 5.5 of FM 4470 and therefore qualify for use under Section 1504.7 of the 2015, 2012, 2009 and 2006 IBC. Page 2 of 106
5.2 Membranes 5.2.1 Firestone is a nominal 45-mil (1.1 mm), 60-mil (1.5 mm), or 80-mil (2.0 mm) thick, polyester scrim reinforced single-ply roof membrane. 5.2.2 Firestone is a nominal 45-mil (1.1 mm) ( 100), 60-mil (1.5 mm) ( 115), or 80-mil (2.0 mm) ( 135) thick, polyester reinforced, single-ply roof membrane produced with an 8-oz polyester backing. 5.2.3 Firestone membranes are nominal 45-mil (1.1 mm) or 60-mil (1.5-mm) thick, internally reinforced thermoplastic (TPO) roof covers with a self-adhering backing. 5.3 Insulations Foam Plastic insulation when used shall have a flame spread index of not more than 75 when tested at the maximum thickness intended for use in accordance with NSI/UL 723 or STM E 84 to qualify for use under Section 2603.3 and Exception 3 of the 2015, 2012, 2009 and 2006 IBC. To qualify for use under Section 2603.4.1.5 of the 2015, 2012, 2009 and 2006 IBC, a thermal barrier is not required for foam plastic insulation that is part of a Class, B, or C roof-covering assembly, provided the assembly with foam plastic insulation complies with FM 4450 or UL 1256. 5.4 Fasteners Fasteners used to mechanically fasten insulation and membranes to the roof deck, shall be corrosion resistant and shall be one of the fasteners identified in Note 2 in the ppendix of this Report. 5.5 dhesive The adhesives used for adhering, or membranes to the insulation or roofing substrate shall be used as noted in the ppendix of this Report. 5.6 sphalt Hot roofing asphalt, when specified in the roofing assemblies shall conform to STM D312, Type III or Type IV. 6. INSTLLTION Firestone single ply membranes shall be installed in accordance with the applicable code, this report and the manufacturer s published installation instructions. The membranes shall be installed in accordance with Section 1507.13 of the 2015, 2012, 2009 and 2006 IBC or Section R905.13 of the 2015, 2012, 2009 and 2006 IRC as applicable, except as noted in this report. The manufacturer s published installation instructions shall be available at all times on the jobsite during installation. The slope of the roof on which the membranes are installed shall be a minimum of 1/4:12 (2% slope and shall not be more than the maximum slope indicated in UL Online Certifications Directory Roofing Systems (TGFU) and in the ppendix of this Report. Penetrations and terminations of the roof covering shall be flashed and made watertight in accordance with the requirements of the membrane manufacturer and applicable code. 6.1 Firestone, and shall be installed in accordance with Firestone Building Products published installation instructions. Page 3 of 106
6.2 System attachment requirements for wind load resistance are set forth in ppendix 1. = imum Design Pressure is the result of testing for wind load resistance based on allowable wind loads. 6.3 For mechanically fastened membrane systems (Type D) over profiled steel deck, membrane shall be installed running perpendicular to steel deck flutes. 6.4 For InvisiWeld installations, care shall be taken to ensure that the InvisiWeld Plates do not line-up with seams in the TPO membrane. This condition precludes proper induction welding of the membrane to the InvisiWeld Plates. 7. FIRE CLSSIFICTION 7.1 New Construction: Roof assemblies utilizing Firestone, or TPO membranes are described in UL Online Certifications Directory Roofing Systems (TGFU) File R9516 and in Tables provided in the ppendix. 7.2 Reroofing: The existing roof shall be inspected in accordance with the provisions and limitations of Section 1510 of the 2015, 2012, 2009 and 2006 IBC or Section R907 of the 2015, 2012, 2009 and 2006 IRC, as applicable. The existing deck shall be inspected to verify that the structure to be reroofed is structurally sound and adequate to support and secure the roofing membrane. Prior to installation of new roof coverings, inspection by and approval from the code official having jurisdiction is required. Firestone, or membranes may be installed over existing Classified Class, B or C roofing systems as described in the UL Product Certification Category for Roofing Materials (TGFU) File R9516, under the heading of Maintenance and Repair. 8. Wind Resistance: 8.1 New Construction: The allowable wind uplift pressures for the roof assemblies are noted in Table 2. Metal edge securement for all systems shall be designed in accordance with NSI/SPRI ES-1, complying with 2015, 2012, 2009 and 2006 IBC Section 1504.5. For certifications of metal edge securement systems in accordance with NSI/SPRI ES-1, see UL Online Certifications Directory Roof-edge Systems, Metal, for Use with Low-slope Roofing Systems (TGJZ). 8.2 Reroofing: Roof covering systems employing mechanical fasteners shall be qualified, to the satisfaction of the code official, as to the adequacy of fasteners penetrating through existing roof coverings into structural substrates. Since the composition and/or condition of any particular underlying existing roofing materials may vary, reroofing material may vary, reroofing with adhered systems is outside the scope of this report. 9. CONDITIONS OF USE Firestone single ply membranes described in this Report comply with, or are suitable alternatives to, what is specified in those codes listed in Section 2 of this Report, subject to the following conditions: 9.1 Materials and methods of installation shall comply with this Report and the manufacturer s published installation instructions. In the event of a conflict between the installation instructions and this Report, this Report governs. 9.2 The membrane shall be installed by authorized applicators approved by Firestone. 9.3 See UL Online Certifications Directory Roofing Systems (TGFU) File R9516. lso refer to the ppendix provided in this Report. Page 4 of 106
9.4 bove-deck thermal insulation board shall comply with the applicable standards listed in Table of Section 1508.2 of the 2015, 2012, 2009 and 2006 IBC. 9.5 Wind uplift pressures on any roof area, including edges and corner zones shall not exceed the allowable wind pressure for the roof covering installed in that area. Refer to the ppendix of this report. 9.6 The allowable wind uplift pressures listed in the ppendix of this report are for the roof systems only. The deck and framing to which the roofing system is shall be designed for the applicable components and cladding and wind loads in accordance with the applicable code. 9.7 When application is over an existing roof, documentation of the wind uplift resistance of the composite roof construction shall be submitted to the code official. 9.8 The metal edge securement shall be designed and installed for wind loads in accordance with Chapter 16 of the 2015, 2012, 2009 and 2006 IBC and test for resistance in accordance with Test Methods RE-1, RE-2, and RE-3 of NSI/SPRI ES-1, except Vult wind speed shall be determined from Figure 1609, 1609B, or 1609C of 2015, 2012, 2009 and 2006 IBC, as applicable. 9.9 The products are manufactured at the locations listed in Table 1 of this Report under the UL LLC Classification and Follow-Up Service Program, which includes audits in accordance with quality elements of ICC-ES cceptance Criteria for Quality Documentation, C 10. 10. SUPPORTING EVIDENCE 10.1 Data in accordance with ICC-ES cceptance Criteria for Membrane Roof-Covering Systems, C75. 10.2 Manufacturer s descriptive product literature, including installation instructions. 10.3 UL test reports and Classification Reports in accordance with NSI/UL 790. See UL Product Certification Category for Roofing Systems (TGFU). 10.4 UL test reports and Classification Reports in accordance with NSI/UL 1897. See UL Product Certification Category for Roofing Systems (TGIK). 10.5 Data in accordance with FM 4474. 10.6 Data in accordance with FM 4470. 10.7 Data in accordance with STM G 154. 10.8 Documentation of quality system elements in accordance with ICC-ES cceptance Criteria for Quality Documentation, C10. 11. IDENTIFICTION Firestone single ply membranes described in this Evaluation Report are identified by a marking bearing the report holder s name (Firestone), the plant identification, the product name, the UL Classification Mark and the evaluation report number UL ER9516-01. The validity of this Evaluation Report is contingent upon this identification appearing on the product. Page 5 of 106
12. USE OF UL EVLUTION REPORT 12.1 The approval of building products, materials or systems is under the responsibility of the applicable authorities having jurisdiction. 12.2 UL Evaluation Reports shall not be used in any manner that implies an endorsement of the product, material or system by UL. 12.3 The current status of this report, as well as a complete directory of UL Evaluation Reports may be found at UL.com via our On-Line Certifications Directory at www.ul.com/erdirectory. Table 1 Manufacturing Locations LISTEE LOCTION FCTORY ID 320 Innovation Way 40, 42, 43, 48, Firestone Building Products Co L L C Wellford SC 29385 49 or 50 393 Denton CIR Firestone Building Products Co L L C 90 or 91 Tuscumbia L 35674 Page 6 of 106
PPENDIX 1: TTCHMENT REQUIREMENTS FOR WIND UPLIFT NCE Table pplication Type Description 1-1 Wood New, Reroof (Tear-Off), Recover -1 Bonded Insulation, Bonded Roof Cover 1C-1 Wood New, Reroof (Tear-Off), Recover C-1 Mechanically ttached Insulation, Bonded Roof Cover 1C-2 Wood New, Reroof (Tear-Off), Recover C-2 Plate-Bonded Roof Cover 1D-1 Wood New, Reroof (Tear-Off), Recover D-1 Insulated, Mechanically ttached Roof Cover (Stress Plates) 1D-2 Wood New, Reroof (Tear-Off), Recover D-1C Insulated, Mechanically ttached Roof Cover (RM Strips) 1E Wood New, Reroof (Tear-Off), Recover E Non-Insulated, Mechanically ttached Roof Cover 2-1 Steel or Concrete New, Reroof (Tear-Off), Recover -1 Bonded Insulation, Bonded Roof Cover 2-2 Steel or Concrete New, Reroof (Tear-Off), Recover -1B Bonded Temp Roof, Bonded Top Insulation, Bonded Roof Cover 2-3 Steel or Concrete New, Reroof (Tear-Off), Recover -1C Thermal Barrier, Bonded Temp Roof, Bonded Top Insulation, Bonded Roof Cover 2-4 Steel or Concrete New, Reroof (Tear-Off) -1D Base Insulation, Mechanically ttached Temp Roof, Bonded Roof Cover 2B-1 Steel or Concrete New, Reroof (Tear-Off), Recover B-1 Mech. ttached Base Insulation, Bonded Top Insulation, Bonded Roof Cover 2C-1 Steel or Concrete New, Reroof (Tear-Off), Recover C-1 Mechanically ttached Insulation, Bonded Roof Cover 2C-2 Steel or Concrete New, Reroof (Tear-Off), Recover C-2 Plate-Bonded Roof Cover 2D-1 Steel or Concrete New, Reroof (Tear-Off), Recover D-1 Insulated, Mechanically ttached Roof Cover (Stress Plates) 2D-2 Steel or Concrete New, Reroof (Tear-Off), Recover D-1B Insulated, Mechanically ttached Roof Cover (Battens) 2D-3 Steel or Concrete New, Reroof (Tear-Off), Recover D-1C Insulated, Mechanically ttached Roof Cover (Strips) 2D-4 Steel or Concrete New, Reroof (Tear-Off) D-2 Vapor retarder, Insulated Mechanically ttached Roof Cover 3-1 Concrete New, Reroof (Tear-Off) -1 Bonded Insulation, Bonded Roof Cover 3-2 Concrete New, Reroof (Tear-Off) -1B Bonded Temp Roof, Bonded Insulation, Bonded Roof Cover 3F Concrete New, Reroof (Tear-Off) F Non-Insulated, Bonded Roof Cover 4 LWIC New, Reroof (Tear-Off) -1 Bonded Insulation, Bonded Roof Cover 4B LWIC New, Reroof (Tear-Off), Recover B-1 Mech. ttached nchor Sheet, Bonded Insulation, Bonded Roof Cover 4C LWIC New, Reroof (Tear-Off), Recover C-2 Plate-Bonded Roof Cover 4D-1 LWIC New, Reroof (Tear-Off), Recover D-1 Insulated, Mechanically ttached Roof Cover (Stress Plates) 4D-2 LWIC New, Reroof (Tear-Off), Recover D-1B Insulated, Mechanically ttached Roof Cover (Battens) 4F LWIC New, Reroof (Tear-Off) F Non-Insulated, Bonded Roof Cover 5 CWF New, Reroof (Tear-Off) -1 Bonded Insulation, Bonded Roof Cover 5B CWF New, Reroof (Tear-Off) -2 Mech. ttached nchor Sheet, Bonded Insulation, Bonded Roof Cover 6 Gypsum Reroof (Tear-Off) -1 Bonded Insulation, Bonded Roof Cover 6B Gypsum Reroof (Tear-Off) -2 Mech. ttached nchor Sheet, Bonded Insulation, Bonded Roof Cover 7 Various Recover -1 Bonded Insulation, Bonded Roof Cover 7B Steel Recover C-2 Plate-Bonded Roof Cover 7C Steel Recover D-1 Insulated, Mechanically ttached Roof Cover 7D Steel Recover E Non-Insulated, Mechanically ttached Roof Cover 7E Various Recover F Non-Insulated, Bonded Roof Cover
The following notes apply to the systems outlined herein: 1. Roof decks shall be in accordance with IBC or IRC requirements to the satisfaction of the HJ. Wind load resistance of the roof deck shall be documented through proper codified pproval documentation. 2. Unless otherwise noted, fasteners and stress plates for insulation attachment shall be as follows. Fasteners shall be of sufficient length for the following engagements: Wood : Firestone ll-purpose or Heavy-Duty Fasteners with Firestone Insulation Fastening Plates. Minimum 1.0- inch plywood penetration or wood plank embedment. Steel : Firestone ll-purpose or Heavy-Duty Fasteners with Firestone Insulation Fastening Plates. Minimum 3 / 4-inch steel penetration, engage the top flute of the steel deck. Concrete : Firestone Heavy-Duty or Concrete Drive Fasteners with Firestone Insulation Fastening Plates. Minimum 1.0-inch embedment. Fasteners installed with a pilot hole in accordance with the fastener manufacturer s published installation instructions 3. Minimum 200 psi, minimum 2-inch thick lightweight insulating may be substituted for rigid insulation board for System Type D-1 (mechanically membrane), whereby the membrane fasteners are installed through the LWIC to engage the structural steel or deck. The structural deck shall be of equal or greater configuration to the steel and deck listings. 4. Preliminary insulation attachment for System Type D = Minimum four fasteners per 4 x 8 ft. board or minimum two fasteners per 4 x 4 ft. board. 5. Insulation adhesive bead width listed below is at the time of application; the beads shall expand as noted in the manufacturer s published instructions. Firestone I.S.O. FIX II: Continuous 3 / 4to 1-inch beads Firestone : Continuous 1/2 to 3 / 4-inch beads Firestone : Continuous 3 / 4 to 1-inch beads Firestone : Continuous 1/2 to 3 / 4-inch beads Unless otherwise noted, the spacing of insulation adhesive is 12-inch o.c.. 6. Unless otherwise noted, all insulations are offered in flat stock or tapered board of the minimum thickness noted. Tapered or Tapered at the following thickness limitations may be substituted with the following imum Design Pressure () limitations. In no case, shall these values be used to increase the listings in the tables; rather if listing below meets or exceeds that listed for a system in the tables, then the thinner board listed below may be used as a dropin for the equivalent thicker material listed in the table. Firestone I.S.O. FIX II: -195.5 psf ( thick) Firestone : -262.5 psf ( thick) Firestone : -262.5 psf ( thick) Firestone : -262.5 psf ( thick) 7. For Recover pplications using System Type D, the insulation is optional. lternatively, min. 0.5-inch or min. 1/4-inch GP Dens, Dens Prime, USG SECUROCK Gypsum-Fiber Roof Board or SECUROCK Glass-Mat Roof Board or CertainTeed GlassRoc may be used as a separator board, preliminarily prior to roof cover installation. The existing roof system shall be suitable for a recover application. 8. For membrane attachment using batten-strips, batten-strip end laps shall be spliced with sufficient dimension to allow for minimum 2-fasteners at each batten-strip lap. 9. For adhered membrane systems, side laps shall be minimum 3-inch wide sealed with min. 1.5-inch heat weld. Membrane adhesive application rates are as follows: Page 8 of 106
Membrane dhesive Method Rate Bonding dhesive (UP-B) Contact pplication 45 to 60 ft. 2 /gal Water Based Bonding dhesive-p (WBB-P) Contact pplication 100 to 120 ft. 2 /gal Single-Ply LVOC Bonding dhesive (LVOC-B) Contact pplication 45 to 60 ft. 2 /gal Single-Ply LVOC Bonding dhesive 1168 (1168) Contact pplication 45 to 60 ft. 2 /gal Self dhered () Contact pplication Not pplicable Hot Mopped, STM D 312, Type IV sphalt (sphalt) Contact pplication 25 to 30 lbs/100 ft. 2 Bonding dhesive (-B) Contact pplication 70 to 90 ft. 2 /gal Stick Membrane dhesive Contact pplication Contact pplication Continuous 3 / 4 to 1-inch wide ribbons Continuous 1 / 2 to 3 / 4-inch wide ribbons 10. TPO Induction Welded Systems (Type C-2):. bonded to InvisiWeld Plates with RhinoBond Portable Plate Bonding Tool and weighted RhinoBond Cooling Clamps. B. bonded to InvisiWeld-S Plates with IsoWeld Portable Plate Bonding Tool and weighted IsoWeld Cooling Clamps. Care shall be taken to ensure that the InvisiWeld Plates do not line-up with seams in the TPO membrane. This condition precludes proper induction welding of the membrane to the InvisiWeld Plates. Side laps shall be minimum 3-inch wide sealed with minimum 1.5-inch heat weld. 11. sphaltic Vapor Barrier / Temp Roof noted herein consists of 1 or 2 plies Ply IV (4) or Ply VI (6) or 1 ply MB Base, SBS Base, SBS PolyBase or SBS Premium Base in hot asphalt. 12. M Base Use one of the following: Channel Venting Base; MB Base; SBS Base; SBS Base-P; SBS Glass Torch Base; SBS Glass Torch Base 1.5; SBS Premium Base; SBS PolyBase; SBS Premium PolyBase; SBS Poly Torch Base; or SBS Smooth 13. = imum Design Pressure is the result of testing for wind load resistance based on allowable wind loads. Refer to IBC Section 1609 or FBC 1609.1.5 for determination of design wind pressures. Page 9 of 106
W-1 W-2 Min. 15/32-inch plywood at max. Min. 15/32-inch plywood at max. Base Insulation Dens or SECUROCK Gypsum-Fiber Roof Board Table 1-1: Wood s- New Construction, Reroof (Tear off), or Recover System Type -1: Bonded Insulation, Bonded Roof Cover Base Insulation attachment I.S.O Stick Insulation Top Insulation Min. 1.0-inch Top Insulation ttachment I.S.O Stick I.S.O Stick Membrane,, Roof Cover Membrane ttachment UP-B, LVOC- B, 1168, UP-B, LVOC- B, 1168, -45.0-45.0 Class Incline W-3 Min. 7/16-inch OSB at max. 24-inch spans Dens Prime, UP-B, LVOC- B, 1168, -45.0 2 W-4 Min. 19/32-inch plywood at max using 8d ring shank nails spaced 6-inch o.c Dens Prime or SECUROCK Gypsum Fiber Roof Board I.S.O. Fix II 6- inch o.c. ribbons, UP-B, LVOC- B, 1168, WBB-P, -67.5 2 ULTRPLY TPO SYSTEMS: W-5 Min. 7/16-inch OSB OR 15/32-inch Plywood at max. 24- inch spans Dens Prime -B, sphalt -45.0 1 W-6 Min. 19/32-inch plywood at max using 8d ring shank nails spaced 6-inch o.c Dens Prime or SECUROCK Gypsum Fiber Roof Board I.S.O. Fix II 6- inch o.c. ribbons sphalt -67.5 1 W-7 Min. 7/16-inch OSB at max. 24-inch spans using 8d ring shank nails spaced 6-inch o.c Dens Prime 12-inch o.c. ribbons -75.0 W-8 Min. 7/16-inch OSB OR 15/32-inch Plywood at max. using 8d ring shank nails spaced 6-inch o.c SECUROCK Gypsum Fiber Roof Board 6-inch o.c. ribbons 6-inch o.c. ribbons -90.0 Page 10 of 106
W-9 W-10 W-11 W-12 W-13 W-14 W-15 W-16 W-17 Min. 7/16-inch OSB at max Min. 7/16-inch OSB or 15/32- inch plywood at max 24-inch spans Min. 7/16-inch OSB at max using 8d ring shank nails spaced 6-inch o.c Min. 15/32-inch plywood at max Min. 19/32-inch plywood at max Min. 19/32-inch plywood at max Min. 7/16-inch OSB at max Min. 7/16-inch OSB at max 24-inch span using 8d ring shank nails spaced 6-inch o.c s Min. 7/16-inch OSB at max using 8d ring shank nails spaced 6-inch o.c TBLE 1C-1: WOOD DECKS - NEW CONSTRUCTION or REROOF (Tear-Off) or RECOVER SYSTEM TYPE C-1: MECHNICLLY TTCHED INSULTION, BONDED ROOF COVER Base Insulation Layer layers, any combination (Loose Laid) layers, any combination (Loose Laid) layers, any combination (Loose Laid) layers, any combination (Loose Laid) layers, any combination (Loose Laid) layers, any combination (Loose Laid) layers, Minimum 1.0-inch or, layers, any combination (Loose Laid) layers, any combination (Loose Laid) Top Insulation Layer Roof Cover dhesive Type Fasteners ttach Class Incline, SECUROCK Gypsum Fiber Roof Board, Dens 2 See Note 2 1 per 3.2 ft., 2 See Note 2 1 per 2.67 ft., Min. 1.0 inch See Note 2 1 per 1.78 ft. 2, Min. 1/2-inch, SECUROCK Gypsum Fiber Roof Board 2 See Note 2 1 per 4.0 ft., See Note 2 1 per 2.67 ft. 2, Min. 60 mil Min. 2.0-inch See Note 2 1 per 4.0 ft. 2, Min. 60 mil or SECUROCK Gypsum- Fiber Roof Board or Dens Prime See Note 2 1 per 2.67 ft. 2, Min. 1.0 inch See Note 2 1 per 1.6 ft. 2, Min. 1/2-inch thick, SECUROCK Gypsum Fiber Roof Board or Dens Prime See Note 2 1 per 1.78 ft. 2, UP-B, LVOC- B-1168, LVOC-B, WBB-P, UP-B, LVOC- B-1168, LVOC-B, WBB-P, UP-B, LVOC- B-1168, LVOC-B, WBB-P, UP-B, LVOC- B-1168, LVOC-B, WBB-P, UP-B, LVOC- B-1168, LVOC-B, WBB-P, UP-B, LVOC- B-1168, LVOC-B, WBB-P, UP-B, LVOC- B, 1168, UP-B, LVOC- B-1168, LVOC-B, WBB-P, UP-B, LVOC- B-1168, LVOC-B, WBB-P, -30.0 2-37.5 2-37.5-37.5 2-37.5 B -42.5-45.0 2-45.0-45.0 2 Page 11 of 106
W-18 W-19 W-20 W-21 W-22 W-23 W-24 W-25 W-26 W-27 Min. 7/16-inch OSB at max using 8d ring shank nails spaced 6-inch o.c Min. 15/32-inch plywood at max Min. 15/32-inch plywood at max Min. 15/32-inch plywood at max using 8d ring shank nails spaced 6-inch o.c Min. 15/32-inch plywood at max Min. 15/32-inch plywood at max using 8d ring shank nails spaced 6-inch o.c Min. 15/32-inch plywood at max Min. 15/32-inch plywood at max Min. 19/32-inch plywood at max Min. 19/32-inch plywood at max TBLE 1C-1: WOOD DECKS - NEW CONSTRUCTION or REROOF (Tear-Off) or RECOVER SYSTEM TYPE C-1: MECHNICLLY TTCHED INSULTION, BONDED ROOF COVER Base Insulation Layer layers, any combination (Loose Laid) layers, any combination (Loose Laid) thick, Dens or SECUROCK Gypsum Fiber Roof Board layers, any combination (Loose Laid) thick, Dens or SECUROCK Gypsum Fiber Roof Board layers, any combination (Loose Laid) thick, Dens or SECUROCK Gypsum Fiber Roof Board (Loose Laid) (Loose Laid) Top Insulation Layer Roof Cover dhesive Type Fasteners ttach Class Incline Composite or Min. 2.0 inch See Note 2 1 per 1.78 ft. 2, Min. 1.0 inch See Note 2 1 per 1.6 ft. 2, Min. 1/2-inch SECUROCK Gypsum- Fiber Roof Board, Dens Prime ISO 95+ GL Composite or Min. 2.0-inch ISO 95+ GL See Note 2 1 per 4.0 ft. 2, See Note 2 1 per 1.78 ft. 2, See Note 2 1 per 2.67 ft. 2, See Note 2 1 per 2.67 ft. 2, See Note 2 1 per 4.0 ft. 2, Min. 2.0-inch See Note 2 1 per 4.0 ft. 2, Min. 2.0-inch ISO 95+ GL Min. 1/2-inch SECUROCK Gypsum- Fiber Roof Board, or Dens Prime See Note 2 1 per 1.78 ft. 2, See Note 2 1 per 1.6 ft. 2, UP-B, LVOC- B-1168, LVOC-B, WBB-P, UP-B, LVOC- B, 1168, UP-B, LVOC- B, 1168, UP-B, LVOC- B-1168, LVOC-B, WBB-P, UP-B, LVOC- B-1168, LVOC-B, WBB-P, UP-B, LVOC- B-1168, LVOC-B, WBB-P, UP-B, LVOC- B-1168, LVOC-B, WBB-P, UP-B, LVOC- B-1168, LVOC-B, WBB-P, UP-B, LVOC- B-1168, WBB-P, UP-B, LVOC- B-1168, LVOC-B, WBB-P, -45.0-45.0-45.0 2- -45.0 2-45.0-45.0-45.0-45.0-45.0-45.0 2- Page 12 of 106
W-28 W-29 W-30 W-31 W-32 W-33 W-34 W-35 W-36 Min. 19/32-inch plywood at max Min. 7/16-inch OSB at max using 8d ring shank nails spaced 6-inch o.c Min. 15/32-inch plywood at max Min. 15/32-inch plywood at max Min. 19/32-inch plywood at max Min. 19/32-inch plywood at max Min. 7/16-inch OSB at max using 8d ring shank nails spaced 6-inch o.c Min. 7/16-inch OSB at max using 8d ring shank nails spaced 6-inch o.c Min. 15/32-inch plywood at max using 8d ring shank nails spaced 6-inch o.c TBLE 1C-1: WOOD DECKS - NEW CONSTRUCTION or REROOF (Tear-Off) or RECOVER SYSTEM TYPE C-1: MECHNICLLY TTCHED INSULTION, BONDED ROOF COVER Base Insulation Layer layers, Minimum 1.0-inch or, (Loose Laid) layers, any combination (Loose Laid) layers, any combination (Loose Laid) layers, any combination (Loose Laid) layers, any combination (Loose Laid) layers, any combination (Loose Laid) layers, any combination (Loose Laid) layers, any combination (Loose Laid) layers, any combination (Loose Laid) Top Insulation Layer Roof Cover dhesive Type Fasteners ttach Class Incline SECUROCK Gypsum- Fiber Roof Board or Dens Prime Min. 1.0 inch Min. 1/2-inch, Dens Prime Min. 1/2-inch, SECUROCK Gypsum Fiber Roof Board Min. 1/2-inch, Dens Prime Min. 1/2-inch, SECUROCK Gypsum Fiber Roof Board Composite 2, See Note 2 1 per 2.13 ft. 2, See Note 2 1 per 1.33 ft. See Note 2 1 per 1.78 ft. 2, 2, See Note 2 1 per 2.13 ft. See Note 2 1 per 2.67 ft. 2, Min. 60 mil See Note 2 1 per 2.13 ft. 2, Min. 60 mil See Note 2 1 per 1.45 ft. 2, See Note 2 1 per 1.45 ft. 2, See Note 2 1 per 1.78 ft. 2, UP-B, LVOC- B-1168, LVOC-B, WBB-P, UP-B, LVOC- B-1168, LVOC-B, WBB-P, UP-B, LVOC- B-1168, LVOC-B, WBB-P, UP-B, LVOC- B-1168, LVOC-B, WBB-P, UP-B, LVOC- B-1168, LVOC-B, WBB-P, UP-B, LVOC- B-1168, LVOC-B, WBB-P, UP-B, LVOC- B-1168, LVOC-B, WBB-P, UP-B, LVOC- B-1168, LVOC-B, WBB-P, UP-B, LVOC- B-1168, LVOC-B, WBB-P, -45.0 2-52.5-52.5 2- -52.5 2- -52.5 2- -55.0 B -60.0 2- -60.0-60.0 Page 13 of 106
W-37 Min. 15/32-inch plywood at max using 8d ring shank nails spaced 6-inch TBLE 1C-1: WOOD DECKS - NEW CONSTRUCTION or REROOF (Tear-Off) or RECOVER SYSTEM TYPE C-1: MECHNICLLY TTCHED INSULTION, BONDED ROOF COVER Base Insulation Layer Top Insulation Layer Roof Cover dhesive Type Fasteners ttach Class Incline Min. 1/2-inch SECUROCK Gypsum- Fiber Roof Board See Note 2 1 per 1.78 ft. 2, UP-B, LVOC- B, 1168, -67.5 2- System ULTRPLY TPO SYSTEMS: W-38 W-39 W-40 W-41 W-42 W-43 Min. 7/16-inch OSB at max Min. 7/16-inch OSB or 15/32- inch plywood at max 24-inch spans Min. 7/16-inch OSB or 15/32- inch plywood at max 24-inch spans Min. 7/16-inch OSB at max using 8d ring shank nails spaced 6-inch o.c Min. 15/32-inch plywood at max Min. 7/16-inch OSB or 15/32- inch plywood at max 24-inch spans TBLE 1C-1: WOOD DECKS - NEW CONSTRUCTION or REROOF (Tear-Off) or RECOVER SYSTEM TYPE C-1: MECHNICLLY TTCHED INSULTION, BONDED ROOF COVER Base Insulation Layer layers, Minimum 1.0-inch or, (Loose Laid) layers, Minimum 1.0-inch or, (Loose Laid) layers, Minimum 1.0-inch or, (Loose Laid) layers, any combination (Loose Laid) layers, any combination (Loose Laid) layers, Minimum 1.0-inch or, (Loose Laid) Top Insulation Layer Roof Cover dhesive Type Fasteners ttach Class Incline, SECUROCK Gypsum Fiber Roof Board, Dens, Dens Min. 1.0 inch Min. 1/2-inch, SECUROCK Gypsum Fiber Roof Board, SECUROCK Gypsum Fiber Roof Board or Dens Prime See Note 2 1 per 3.2 ft. 2 See Note 2 1 per 2.67 ft. 2 See Note 2 1 per 2.67 ft. 2 See Note 2 1 per 1.78 ft. 2 See Note 2 1 per 4.0 ft. 2 See Note 2 1 per 2.67 ft. 2 sphalt; - B Stick or ISO Spray R, 12-inch o.c. sphalt; - B Stick, 6-in. o.c. or ISO Spray R, 12-in. o.c. sphalt; - B Stick or ISO Spray R, 12-in. o.c. -30.0 1-37.5-37.5 1-37.5 B -37.5 1-45.0 Page 14 of 106
ULTRPLY TPO SYSTEMS: Min. 7/16-inch OSB or 15/32- W-44 inch plywood at max 24-inch spans Min. 7/16-inch OSB at max W-45 using 8d ring shank nails spaced 6-inch o.c Min. 7/16-inch OSB at max W-46 using 8d ring shank nails spaced 6-inch o.c Min. 7/16-inch OSB at max W-47 using 8d ring shank nails spaced 6-inch o.c Min. 7/16-inch OSB at max W-48 using 8d ring shank nails spaced 6-inch o.c Min. 15/32-inch plywood at max W-49 using 8d ring shank nails spaced 6-inch o.c Min. 15/32-inch plywood at max W-50 using 8d ring shank nails spaced 6-inch o.c TBLE 1C-1: WOOD DECKS - NEW CONSTRUCTION or REROOF (Tear-Off) or RECOVER SYSTEM TYPE C-1: MECHNICLLY TTCHED INSULTION, BONDED ROOF COVER Base Insulation Layer layers, Minimum 1.0-inch or, (Loose Laid) layers, any combination (Loose Laid) layers, any combination (Loose Laid) layers, any combination (Loose Laid) layers, any combination (Loose Laid) layers, Minimum 1.0-inch or, (Loose Laid) layers, Minimum 1.0-inch or, (Loose Laid) Top Insulation Layer Roof Cover dhesive Type Fasteners ttach Class Incline, SECUROCK Gypsum- Fiber Roof Board or Dens Prime Min. 1.0 inch Min. 1/2-inch thick, SECUROCK Gypsum Fiber Roof Board or Dens Prime Min. 1/2-inch thick, SECUROCK Gypsum Fiber Roof Board or Dens Prime Composite or Min. 2.0 inch, Dens, Dens See Note 2 1 per 2.67 ft. 2 See Note 2 1 per 1.6 ft. 2 See Note 2 1 per 1.78 ft. 2 See Note 2 1 per 1.78 ft. 2 See Note 2 1 per 1.78 ft. 2 See Note 2 1 per 1.78 ft. 2 See Note 2 1 per 1.78 ft. 2 sphalt; - B Stick, 6-in. o.c. or ISO Spray R, 12-in. o.c. Stick, 6-in. o.c. or ISO Spray R, 12-in. o.c. sphalt; - B Stick, 6-in. o.c. or ISO Spray R, 12-in. o.c. Stick or ISO Spray R, 12-in. o.c. sphalt; - B -45.0 1-45.0 B -45.0-45.0 1-45.0 B -45.0-45.0 1 Page 15 of 106
ULTRPLY TPO SYSTEMS: W-51 W-52 W-53 W-54 W-55 W-56 W-57 W-58 W-59 W-60 W-61 Min. 15/32-inch plywood at max Min. 15/32-inch plywood at max Min. 15/32-inch plywood at max using 8d ring shank nails spaced 6-inch o.c Min. 15/32-inch plywood at max Min. 15/32-inch plywood at max Min. 15/32-inch plywood at max Min. 19/32-inch plywood at max Min. 7/16-inch OSB at max using 8d ring shank nails spaced 6-inch o.c Min. 15/32-inch plywood at max Min. 15/32-inch plywood at max Min. 15/32-inch plywood at max TBLE 1C-1: WOOD DECKS - NEW CONSTRUCTION or REROOF (Tear-Off) or RECOVER SYSTEM TYPE C-1: MECHNICLLY TTCHED INSULTION, BONDED ROOF COVER Base Insulation Layer layers, any combination (Loose Laid) layers, any combination (Loose Laid) layers, any combination (Loose Laid) thick, Dens or SECUROCK Gypsum Fiber Roof Board thick, Dens or SECUROCK Gypsum Fiber Roof Board layers, any combination (Loose Laid) layers, Minimum 1.0-inch or, layers, any combination (Loose Laid) layers, any combination (Loose Laid) layers, any combination (Loose Laid) layers, any combination (Loose Laid) Top Insulation Layer Roof Cover dhesive Type Fasteners ttach Class Incline Min. 1/2-inch, SECUROCK Gypsum- Fiber Roof Board Min. 1/2-inch, SECUROCK Gypsum- Fiber Roof Board Composite or ISO 95+ GL Min. 2.0-inch ISO 95+ GL Min. 2.0-inch Dens or SECUROCK Gypsum- Fiber Roof Board or Dens Prime Min. 1.0 inch Min. 1/2-inch, Dens Prime Min. 1/2-inch, Dens Prime Min. 1/2-inch, SECUROCK Gypsum- Fiber Roof Board See Note 2 1 per 4.0 ft. 2 Stick or ISO Spray R, 12-in. o.c. -45.0 See Note 2 1 per 4.0 ft. 2 sphalt -45.0 1 See Note 2 1 per 2.67 ft. 2 See Note 2 1 per 2.67 ft. 2 See Note 2 1 per 4.0 ft. 2 See Note 2 1 per 4.0 ft. 2 See Note 2 1 per 2.13 ft. 2 See Note 2 1 per 1.33 ft. 2 See Note 2 1 per 1.78 ft. 2 See Note 2 1 per 1.78 ft. 2 See Note 2 1 per 2.13 ft. 2 Stick or ISO Spray R, 12-in. o.c. ISO Spray R, 12-in. o.c. ISO Spray R, 12-in. o.c. ISO Spray R, 12-in. o.c. sphalt; - B Stick, 6-in. o.c. or ISO Spray R, 12-in. o.c. Stick or ISO Spray R, 12-in. o.c. sphalt; - B Stick or ISO Spray R, 12-in. o.c. -45.0 B -45.0-45.0 B B -45.0 B 3 / 4 3 / 4-45.0 1-52.5 B -52.5-52.5 1-52.5 Page 16 of 106
ULTRPLY TPO SYSTEMS: W-62 W-63 W-64 W-65 W-66 W-67 Min. 15/32-inch plywood at max Min. 7/16-inch OSB at max using 8d ring shank nails spaced 6-inch o.c Min. 7/16-inch OSB at max using 8d ring shank nails spaced 6-inch o.c Min. 7/16-inch OSB at max using 8d ring shank nails spaced 6-inch o.c Min. 15/32-inch plywood at max Min. 15/32-inch plywood at max using 8d ring shank nails spaced 6-inch o.c TBLE 1C-1: WOOD DECKS - NEW CONSTRUCTION or REROOF (Tear-Off) or RECOVER SYSTEM TYPE C-1: MECHNICLLY TTCHED INSULTION, BONDED ROOF COVER Base Insulation Layer layers, any combination (Loose Laid) layers, any combination (Loose Laid) layers, any combination (Loose Laid) layers, any combination (Loose Laid) layers, any combination (Loose Laid) layers, any combination (Loose Laid) Top Insulation Layer Roof Cover dhesive Type Fasteners ttach Class Incline Min. 1/2-inch, SECUROCK Gypsum- Fiber Roof Board Min. 1/2-inch, SECUROCK Gypsum Fiber Roof Board Min. 1/2-inch, SECUROCK Gypsum Fiber Roof Board Composite Min. 1/2-inch, SECUROCK Gypsum- Fiber Roof Board See Note 2 1 per 2.13 ft. 2 See Note 2 1 per 1.45 ft. 2 See Note 2 1 per 1.45 ft. 2 See Note 2 1 per 1.45 ft. 2 See Note 2 1 per 1.78 ft. 2 See Note 2 1 per 1.78 ft. 2 sphalt; - B Stick, 6-in. o.c. or ISO Spray R, 12-in. o.c. sphalt; - B Stick, 6-in. o.c. or ISO Spray R, 12-in. o.c. Stick or ISO Spray R, 12-in. o.c. sphalt; - B -52.5 1-60.0-60.0 1-60.0 B -60.0 B -67.5 1 Page 17 of 106
W-68 W-69 W-70 W-71 W-72 W-73 W-74 W-75 W-76 W-77 Min. 15/32-inch plywood at max. Min. 15/32-inch plywood at max. Min. 15/32-inch plywood at max. Min. 7/16-inch OSB or 15/32-inch plywood at max 24- inch spans Min. 7/16-inch OSB or 15/32-inch plywood at max 24- inch spans Min. 7/16-inch OSB or 15/32-inch plywood at max 24- inch spans Min. 15/32-inch plywood at max. using 8d ring shank nails spaced 6-inch o.c Min. 15/32-inch plywood at max. using 8d ring shank nails spaced 6-inch o.c Min. 15/32-inch plywood at max. using 8d ring shank nails spaced 6-inch o.c Min. 19/32-inch OSB at max. 24- inch spans TBLE 1C-2: WOOD DECKS - NEW CONSTRUCTION, REROOF (Tear-Off) or RECOVER SYSTEM TYPE C-2: PLTE-BONDED ROOF COVER Insulation ttachment Membrane Base Layer Top Layer Fasteners Density / Pattern ttachment Class Incline (Optional) Min. 1.0- Firestone Dens or 1 fastener per 5.33 ft. 2 inch or Heavy Duty See Note 10 or 10B -30.0 1 SECUROCK Gypsum- (6 per 4 x 8 board) Fasteners Fiber Roof Board (Optional) Min. 1.0- inch or (Optional) Min. 1.0- inch or (Optional) Min. 1.0- inch or (Optional) Min. 1.0- inch or (Optional) Min. 1.0- inch or (Optional) Min. 1.0- inch or (Optional) Min. 1.0- inch or (Optional) Min. 1.0- inch or (Optional) Min. 1- inch or Min. 1.0 inch Composite Dens or SECUROCK Gypsum- Fiber Roof Board Min. 1.0-inch Composite Dens or SECUROCK Gypsum- Fiber Roof Board Min. 1.0-inch Composite Dens or SECUROCK Gypsum-Fiber Roof Board Firestone Heavy Duty Fasteners Firestone Heavy Duty Fasteners Firestone Heavy Duty Fasteners Firestone Heavy Duty Fasteners Firestone Heavy Duty Fasteners Firestone Heavy Duty Fasteners Firestone Heavy Duty Fasteners Firestone Heavy Duty Fasteners Firestone Heavy Duty Fasteners 1 fastener per 5.33 ft. 2 (6 per 4 x 8 board) 1 fastener per 5.33 ft. 2 (6 per 4 x 8 board) Plates secured 24-in. o.c. through deck into wood joists in rows spaced 48-inch o.c. Plates secured 24-in. o.c. through deck into wood joists in rows spaced 48-inch o.c. Plates secured 24-inch o.c. through deck into wood joists in rows spaced 48-inch o.c. 1 fastener per 4.0 ft. 2 (8 per 4 x 8 board) 1 fastener per 4.0 ft. 2 (8 per 4 x 8 board) 1 fastener per 4.0 ft. 2 (8 per 4 x 8 board) 1 fastener per 5.33 ft. 2 (6 per 4 x 8 board) See Note 10 or 10B -30.0 See Note 10 or 10B -30.0 B 1- See Note 10 or 10B -45.0 1 See Note 10 or 10B -45.0 See Note 10 or 10B -45.0 B 1- See Note 10 or 10B -45.0 1 See Note 10 or 10B -45.0 See Note 10 or 10B -45.0 B 1- See Note 10 or 10B -45.0 1 Page 18 of 106
W-78 W-79 W-80 W-81 W-82 W-83 W-84 W-85 Min. 19/32-inch OSB at max. 24- inch spans Min. 19/32-inch OSB at max. 24- inch spans 15/32-inch Plywood at max. 24- inch spans 15/32-inch Plywood at max. 24-inch spans 15/32-inch Plywood at max. 24-inch spans Min. 7/16-inch OSB or 15/32-inch plywood at max 24- inch spans using 8d ring shank nails spaced 6-inch o.c Min. 7/16-inch OSB or 15/32-inch plywood at max 24- inch spans using 8d ring shank nails spaced 6-inch o.c Min. 7/16-inch OSB or 15/32-inch plywood at max 24- inch spans using 8d ring shank nails spaced 6-inch o.c TBLE 1C-2: WOOD DECKS - NEW CONSTRUCTION, REROOF (Tear-Off) or RECOVER SYSTEM TYPE C-2: PLTE-BONDED ROOF COVER Insulation ttachment Membrane Base Layer Top Layer Fasteners Density / Pattern ttachment Class Incline Dens Firestone (Optional) ISO 95+ or SECUROCK 1 fastener per 5.33 ft. 2 Heavy Duty See Note 10 or 10B -45.0 GL or Gypsum-Fiber Roof (6 per 4 x 8 board) B 1- Fasteners Board (Optional) ISO 95+ GL or (Optional) Min. 1- inch or (Optional) ISO 95+GL or (Optional) ISO 95+GL or (Optional) Min. 1- inch or (Optional) ISO 95+GL or (Optional) ISO 95+GL or Dens or SECUROCK Gypsum-Fiber Roof Board Dens or SECUROCK Gypsum-Fiber Roof Board Min. 1.0-inch Composite Dens or SECUROCK Gypsum-Fiber Roof Board Min. 1.0 inch Composite Firestone Heavy Duty Fasteners Firestone Heavy Duty Fasteners Firestone Heavy Duty Fasteners Firestone Heavy Duty Fasteners Firestone Heavy Duty Fasteners Firestone Heavy Duty Fasteners Firestone Heavy Duty Fasteners 1 fastener per 5.33 ft. 2 (6 per 4 x 8 board) 1 fastener per 2.7 ft.² (12 per 4 x 8 board) 1 fastener per 2.7 ft.² (12 per 4 x 8 board) 1 fastener per 2.7 ft.² (12 per 4 x 8 board) Plates secured 6-inch o.c. into rafters/trusses in rows spaced 96-inch o.c. Plates secured 6-inch o.c. into rafters/trusses in rows spaced 96-inch o.c. Plates secured 6-inch o.c. into rafters/trusses in rows spaced 96-inch o.c. See Note 10 or 10B -45.0 See Note 10 or 10B -52.5 1 See Note 10 or 10B -52.5 See Note 10 or 10B -52.5 B 1- See Note 10 or 10B -75.0 1 See Note 10 or 10B -75.0 See Note 10 or 10B -75.0 B 1- Page 19 of 106
W-86 W-87 W-88 W-89 W-90 W-91 W-92 W-93 Min. 7/16-inch OSB or min. 15/32-inch Plywood at max 24- inch span using 8d ring shank nails spaced 6-inch o.c Min. 7/16-inch OSB or min. 15/32-inch Plywood at max 24- inch span using 8d ring shank nails spaced 6-inch o.c Min. 7/16-inch OSB or min. 15/32-inch Plywood at max 24- inch span using 8d ring shank nails spaced 6-inch o.c Min. 19/32-inch OSB at max using 8d ring shank nails spaced 6- inch o.c Min. 19/32-inch OSB at max using 8d ring shank nails spaced 6- inch o.c Min. 19/32-inch OSB at max using 8d ring shank nails spaced 6- inch o.c Min. 7/16-inch OSB or min. 15/32-inch Plywood at max 24-inch spans using 8d ring shank nails spaced 6-inch o.c Min. 7/16-inch OSB or min. 15/32-inch Plywood at max 24-inch spans using 8d ring shank nails spaced 6-inch o.c TBLE 1D-1: WOOD DECKS - NEW CONSTRUCTION, REROOF (Tear-Off) or RECOVER SYSTEM TYPE D-1: INSULTED, MECHNICLLY TTCHED ROOF COVER (Stress Plates) Insulation Roof Cover Base Layer Top Layer ttach Membrane Fasteners ttachment Class (Optional) V-Force Vapor Barrier; (Optional) one or more layers, Min. 1.0-inch ISO 95+ GL or (Optional) one or more layers, ISO 95+ GL or (Optional) one or more layers, ISO 95+ GL or (Optional) one or more layers, Min. 1.0-inch ISO 95+ GL or (Optional) one or more layers, ISO 95+ GL or (Optional) one or more layers, ISO 95+ GL or (Optional) one or more layers, Min. 1.0-inch ISO 95+ GL or (Optional) one or more layers, ISO 95+ GL or Dens or SECUROCK Gypsum Fiber Roof Board Min. 1.0-inch or Composite Dens or SECUROCK Gypsum Fiber Roof Board Min. 1.0-inch or Composite Dens or SECUROCK Gypsum Fiber Roof Board Min. 1.0-inch or Composite Fasteners with Seam Plates Fasteners with Seam Plates Fasteners with Seam Plates Fasteners with Seam Plates Fasteners with Seam Plates Fasteners with Seam Plates Fasteners with Seam Plates Fasteners with Seam Plates 6-inch o.c. within 6-inch wide laps spaced 4.5-ft. o.c. Laps sealed with 1.5-inch heat weld. 6-inch o.c. within 6-inch wide laps spaced 4.5-ft. o.c. Laps sealed with 1.5-inch heat weld. 6-inch o.c. within 6-inch wide laps spaced 4.5-ft. o.c. Laps sealed with 1.5-inch heat weld. 9-inch o.c. within 6-inch wide laps spaced 90- inch o.c. Laps sealed with 1.5-inch heat weld. 9-inch o.c. within 6-inch wide laps spaced 90- inch o.c. Laps sealed with 1.5-inch heat weld. 9-inch o.c. within 6-inch wide laps spaced 90- inch o.c. Laps sealed with 1.5-inch heat weld. 18-inch o.c. within 6- inch wide laps spaced 3.5-ft. o.c. Laps sealed with 1.5-inch heat weld. 18-inch o.c. within 6- inch wide laps spaced 3.5-ft. o.c. Laps sealed with 1.5-inch heat weld. Incline -30.0 3-30.0-30.0 B -30.0 3-30.0-30.0 B -37.5 3-37.5 1 / 2 Page 20 of 106
W-94 W-95 W-96 W-97 W-98 W-99 W-100 W-101 W-102 Min. 7/16-inch OSB or min. 15/32-inch Plywood at max 24-inch spans using 8d ring shank nails spaced 6-inch o.c Min. 19/32-inch OSB at max using 8d ring shank nails spaced 6- inch o.c Min. 19/32-inch OSB at max using 8d ring shank nails spaced 6- inch o.c Min. 19/32-inch OSB at max using 8d ring shank nails spaced 6- inch o.c Min. 19/32-inch OSB at max using 8d ring shank nails spaced 6- inch o.c Min. 19/32-inch OSB at max using 8d ring shank nails spaced 6- inch o.c Min. 19/32-inch OSB at max using 8d ring shank nails spaced 6- inch o.c Min. 7/16-inch OSB or min. 15/32-inch Plywood at max 24-inch spans Min. 7/16-inch OSB or min. 15/32-inch Plywood at max 24-inch spans TBLE 1D-1: WOOD DECKS - NEW CONSTRUCTION, REROOF (Tear-Off) or RECOVER SYSTEM TYPE D-1: INSULTED, MECHNICLLY TTCHED ROOF COVER (Stress Plates) Insulation Roof Cover Base Layer Top Layer ttach Membrane Fasteners ttachment Class (Optional) one or more layers, ISO 95+ GL or (Optional) one or more layers, Min. 1.0-inch ISO 95+ GL or (Optional) one or more layers, ISO 95+ GL or (Optional) one or more layers, ISO 95+ GL or (Optional) one or more layers, Min. 1.0-inch ISO 95+ GL or (Optional) one or more layers, ISO 95+ GL or (Optional) one or more layers, ISO 95+ GL or (Optional) one or more layers, Min. 1.0-inch ISO 95+ GL or (Optional) one or more layers, ISO 95+ GL or Dens or SECUROCK Gypsum Fiber Roof Board Min. 1.0-inch or Composite Dens or SECUROCK Gypsum Fiber Roof Board Min. 1.0-inch or Composite Dens or SECUROCK Gypsum Fiber Roof Board Min. 1.0-inch or Composite 60 or 80 mil 60 or 80 mil 60 or 80 mil 60 or 80 mil 60 or 80 mil 60 or 80 mil Fasteners with Seam Plates Fasteners with Seam Plates Fasteners with Seam Plates Fasteners with Seam Plates Fasteners with Seam Plates Fasteners with Seam Plates Fasteners with Seam Plates Fasteners with Seam Plates Fasteners with Seam Plates 18-inch o.c. within 6- inch wide laps spaced 3.5-ft. o.c. Laps sealed with 1.5-inch heat weld. 6-inch o.c. within 6-inch wide laps spaced 90- inch o.c. Laps sealed with 1.5-inch heat weld. 6-inch o.c. within 6-inch wide laps spaced 90- inch o.c. Laps sealed with 1.5-inch heat weld. 6-inch o.c. within 6-inch wide laps spaced 90- inch o.c. Laps sealed with 1.5-inch heat weld. 6-inch o.c. within 6-inch wide laps spaced 114- inch o.c. Laps sealed with 1.5-inch heat weld. 6-inch o.c. within 6-inch wide laps spaced 114- inch o.c. Laps sealed with 1.5-inch heat weld. 6-inch o.c. within 6-inch wide laps spaced 114- inch o.c. Laps sealed with 1.5-inch heat weld. 6-inch o.c. within 6-inch wide laps spaced 3.5-ft. o.c. Laps sealed with 1.5-inch heat weld. 6-inch o.c. within 6-inch wide laps spaced 3.5-ft. o.c. Laps sealed with 1.5-inch heat weld. -37.5 B Incline -37.5 3-37.5-37.5 B -37.5 3-37.5-37.5 B -45.0 3-45.0 Page 21 of 106
W-103 W-104 W-105 W-106 W-107 W-108 W-109 W-110 Min. 7/16-inch OSB or min. 15/32-inch Plywood at max 24-inch spans Min. 15/32-inch plywood at max. 24- inch spans using 8d ring shank nails spaced 6-inch o.c. Min. 15/32-inch plywood at max. 24- inch spans using 8d ring shank nails spaced 6-inch o.c. Min. 15/32-inch plywood at max. 24- inch spans using 8d ring shank nails spaced 6-inch o.c. Min. 19/32-inch OSB at max using 8d ring shank nails spaced 6- inch o.c Min. 19/32-inch OSB at max using 8d ring shank nails spaced 6- inch o.c Min. 19/32-inch OSB at max using 8d ring shank nails spaced 6- inch o.c Min. 19/32-inch plywood at max 24-inch spans TBLE 1D-1: WOOD DECKS - NEW CONSTRUCTION, REROOF (Tear-Off) or RECOVER SYSTEM TYPE D-1: INSULTED, MECHNICLLY TTCHED ROOF COVER (Stress Plates) Insulation Roof Cover Base Layer Top Layer ttach Membrane Fasteners ttachment Class (Optional) one or more layers, ISO 95+ GL or (Optional) one or more layers, Min. 1.0-inch ISO 95+ GL or ; (Optional) one or more layers, ISO 95+ GL or (Optional) one or more layers, ISO 95+ GL or (Optional) one or more layers, Min. 1.0-inch ISO 95+ GL or (Optional) one or more layers, ISO 95+ GL or (Optional) one or more layers, ISO 95+ GL or (Optional) one or more layers, Min. 1.0-inch ISO 95+ GL or Dens or SECUROCK Gypsum Fiber Roof Board Min. 1.0-inch or Composite Dens or SECUROCK Gypsum Fiber Roof Board Min. 1.0-inch or Composite Dens or SECUROCK Gypsum Fiber Roof Board 60 or 80 mil 60 or 80 mil 60 or 80 mil 60 or 80 mil 60 or 80 mil 60 or 80 mil Fasteners with Seam Plates Fasteners with Seam Plates Fasteners with Seam Plates Fasteners with Seam Plates Fasteners with Seam Plates Fasteners with Seam Plates Fasteners with Seam Plates Fasteners with Seam Plates 6-inch o.c. within 6-inch wide laps spaced 3.5-ft. o.c. Laps sealed with 1.5-inch heat weld. 5-inch o.c. within 6-inch wide laps spaced 114- inch o.c. Laps sealed with 1.5-inch heat weld. 5-inch o.c. within 6-inch wide laps spaced 114- inch o.c. Laps sealed with 1.5-inch heat weld. 5-inch o.c. within 6-inch wide laps spaced 114- inch o.c. Laps sealed with 1.5-inch heat weld. 6-inch o.c. within 6-inch wide laps spaced 114- inch o.c. Laps sealed with 1.5-inch heat weld. 6-inch o.c. within 6-inch wide laps spaced 114- inch o.c. Laps sealed with 1.5-inch heat weld. 6-inch o.c. within 6-inch wide laps spaced 114- inch o.c. Laps sealed with 1.5-inch heat weld. 24-inch o.c. within 6- inch wide laps spaced 3.5-ft. o.c. Laps sealed with 1.5-inch heat weld. -45.0 B Incline -45.0 3-45.0-45.0 B -45.0 3-45.0-45.0 B -45.0 3 Page 22 of 106
W-111 W-112 W-113 W-114 W-115 W-116 Min. 19/32-inch plywood at max 24-inch spans Min. 19/32-inch plywood at max 24-inch spans Min. 19/32-inch OSB at max using 8d ring shank nails spaced 6-inch o.c Min. 19/32-inch OSB at max using 8d ring shank nails spaced 6-inch o.c Min. 19/32-inch OSB at max using 8d ring shank nails spaced 6-inch o.c Min. 19/32-inch plywood or wood plank at max. using 10d ring shank nails spaced 4-inch o.c. at board edges and 8d ring shank nails spaced 6-inch o.c. in the field TBLE 1D-1: WOOD DECKS - NEW CONSTRUCTION, REROOF (Tear-Off) or RECOVER SYSTEM TYPE D-1: INSULTED, MECHNICLLY TTCHED ROOF COVER (Stress Plates) Insulation Roof Cover Base Layer Top Layer ttach Membrane Fasteners ttachment Class (Optional) one or more layers, ISO 95+ GL or (Optional) one or more layers, ISO 95+ GL or ; (Optional) one or more layers, Min. 1.0-inch ISO 95+ GL or (Optional) one or more layers, ISO 95+ GL or (Optional) one or more layers, ISO 95+ GL or thick, Dens or SECUROCK Gypsum Fiber Roof Board Min. 1.0-inch or Composite Dens or SECUROCK Gypsum Fiber Roof Board Min. 1.0-inch or Composite thick, one or more layers, and/or 60 or 80 mil 60 or 80 mil 60 or 80 mil TPO Fasteners with Seam Plates Fasteners with Seam Plates Fasteners with Seam Plates Fasteners with Seam Plates Fasteners with Seam Plates Fasteners with Seam Plates 24-inch o.c. within 6- inch wide laps spaced 3.5-ft. o.c. Laps sealed with 1.5-inch heat weld. 24-inch o.c. within 6- inch wide laps spaced 3.5-ft. o.c. Laps sealed with 1.5-inch heat weld. 5-inch o.c. within 6-inch wide laps spaced 90- inch o.c. Laps sealed with 1.5-inch heat weld. 5-inch o.c. within 6-inch wide laps spaced 90- inch o.c. Laps sealed with 1.5-inch heat weld. 5-inch o.c. within 6-inch wide laps spaced 90- inch o.c. Laps sealed with 1.5-inch heat weld. 6-inch o.c. within 6-inch wide laps spaced 90.5- inch o.c. Laps sealed with 5-inch heat weld. -45.0-45.0 B Incline -52.5 3-52.5-52.5 B -60.0 1 Page 23 of 106