CEILING & WALL SYSTEMS TECHNICAL GUIDE DrywallSystem QUIKSTIX WALL LINER Drywall System (Patent Pending) FASTER: Eliminate measuring and marking with QuikStix EASIER: Keep both feet on the floor while simply clicking QuikStix s into BETTER: Time saving integrated system with Roll and s
DrywallSystem QUIKSTIX WALL LINER COMPONENTS TM QuikStix Walls Item Details Item Number Length/ Item Description Face Dimensions Profile Height Perspective QSWFT09 9 1-1/2 1-5/8 QSWFT10 10 1-1/2 1-5/8 QSWFT12 12 1-1/2 1-5/8 QSWFT14 14 1-1/2 1-5/8 QSWLT10 10 (ing Tabs 8 On Center) 1-1/4 Tall Face 1-3/8 Wide Base 1-3/4 Tall Back QSWSB TM Roll 50 3/8 7/8 QSUTC (Screw Holes 1 On Center) 2 Wide Note: All components are available with G90 hot dipped galvanized coating as special order. Just add G90 suffix to end of item number. Cavity Insulation 16 o.c.) (Ceiling) joint 10 QSUTC cables can run along QSWSB Roll Box Gypsum Board Rigid Insulation directly on concrete wall Rigid Insulation in s Roll Insulation s Fi-Foil Insulation (Adhere on face of and must be installed with air space) QSUTC QSWSB Roll (Floor) Optional space between concrete and System For more information call 1 877 ARMSTRONG 2
QUIKSTIX WALL LINER Corner and Extra Weight Loads 2 x 8 Wood block screwed inside s for cabinet mounting Recommend QSUTC at Gypsum Board joints positive attachment 16 o.c. Gypsum Board Hole Pan Head Screw Cabinets must be supported to structure. required on every at cabinets, etc. (Positively attached to structure.) QSWSB Roll Two s 8 Hole Cut ing to form 90 corner Pan Head Screw 10 Using s and Roll 1-5/8 16 16 QSUTC s typically installed 4 o.c. and at Gypsum Board joints QSUTC screwed to web of Condition: Screw short side of QSUTC to Bottom positive attachment Flange 1-5/8 QSWSB Roll Bulb For wide air space: Screw long side of QSUTC to. (Cut to length as necessary.) QSWSB Roll (Overlap and screw together as necessary.) Bottom Bottom Inside Corner Detail 1 Insert Support Bar into electrical knockout as shown 2 Twist bar toward living space Bottom Bottom Outside Corner Detail QSWSB Roll 3 Bar locked into position 3
QUIKSTIX WALL LINER DrywallSystem Methods of Construction Uneven Concrete Walls Wall ing (shot to deck) QSWSB Roll Concrete Block Knockout at Mid-point Wall ing can run along and through hole (grommets supplied by electrician) QSWSB Roll Concrete Wall Condition Wall ing (shot to floor) QSUTC (Fasten to and wall to provide lateral support) Hole for Wall ing For more information call 1 877 ARMSTRONG 4
DrywallSystem QUIKSTIX WALL LINER Installation Instructions NOTE: WEAR APPROPRIATE SAFETY EQUIPMENT WHEN INSTALLING OUR PRODUCT END VIEW Face Back Face Side (Drywall Side) 16 or 24 o.c. 1-3/4 Slide Steel into lock position 7/8 Weep Hole 8 o.c. Bulb Back Side TOP VIEW Step 1 To determine proper location for, string a chalk line on ceiling and on the floor. Chalk line Cut s 1/4 shorter than actual inside dimensions of track. Ceiling ing Ceiling Straight vertical alignment between top and bottom locks. Step 2 Measure and cut proper length of and. Cut with snips or chop saw. Cut s 1/2 shorter than actual inside dimension of track. Step 3 Install in straight vertical alignment to receive s. (Ceiling) or 24 o.c. or 24 o.c. First, insert in top of ing. Next, slide bottom of into position until it locks. Can cut bundles with chop saw. (Floor) Chalk line Floor ing joint Start at left of lock. (Insert top of first.) Step 4 Position into top then into bottom until locked in place. 10 Turn clockwise to lock into top and bottom of track. (Do not twist.) Optional wood block for baseboard attachment. Start at right of lock. (Slide bottom in last.) For more information call 1 877 ARMSTRONG 5
AWI Licensing Company, 2008 Printed in United States of America CS-3950-1008 Please Recycle