Specification Section Title Notation A Product Data Approved as Noted B Shop Drawings Approved as Noted

Submittal Review TO: Pavilion Construction DATE: 07.13.2015 JOB NO.: 1484P 4700 SW Macadam Ave Suite 200 ATTENTION: Riley Tobin Portland, OR 97239 RE: BSD Sunset High School Concession Stand/Interior Renovations Package 1 Submittal: 105113 Metal Lockers Approved Approved As Noted Revise as Noted/Resubmit Rejected/Resubmit As Specified No Action Required Submittal Not Requested/Returned Without Review Approval is for conformance with information given and the design concept expressed in the Contract Documents. Contractor is responsible for quantities and dimensions to be confirmed and correlated; for fabrication process; for means methods, techniques, sequences and procedures of construction; for coordination of the Work; and for all safety aspects of performing the Work. Approval does not modify the Contract Documents and approval of a specific item does not indicate approval of an assembly of which the item is a component. Specification Section Title Notation 105113 1.4A Product Data Approved as Noted 105113 1.4B Shop Drawings Approved as Noted 105113 1.4C Samples For Each Color Selected Approved as Noted. See note 4 105113 1.4D Samples For Initial Selection Approved as Noted. 105113 1.4E Samples For Verification Not Submitted. Resubmit 105113 1.4 F Product Schedule Reviewed in Submittal 3-10 51 13-0 105113 1.5A Qualification Data Reviewed in Submittal 4-10 51 13-0 105113 1.5B Sample Warranty Reviewed in Submittal 4-10 51 13-0 Summary Comments: 1. G.C. to verify all dimensions and Locations. 2. See the attached pdf for additional comments. 3. Beaverton School District has selected color #706 Heather. 4. Locker type B K.D. construction is acceptable per Jessica Faust of BSD. 5. See previous locker submittal for approved numbering scheme. 6. See page # SB-2301-2 for comment on filler panel dimensions. 1001 SW 5 th Ave. // Suite 1100 // Portland // OR 97204-1127 // P: 503.535.0707 // www.blrb.com

Sunset High School 13840 NW Cornell Rd. Portland, OR 97229 To: Attn: BLRB ARCHITECTS, P.S. RICHARD HIGGINS 1001 SW 5TH AVE., SUITE 1100 PORTLAND, OR 97204 Date: Contact Phone: Contact Email: 07/09/2015 503-535-0707 RHIGGINS@BLRB.COM CC d: SUBMITTAL TRANSMITTAL FOR APPROVAL Submittal #: 42 Rev.#: 1 In Accordance with Specification Section #: 105113 This is a submittal for Metal Lockers items per the table below as reviewed and noted by Pavilion Construction NW, LLC, and provided by. Please provide a response to this submittal by 07/13/2015. Pavilion Status: Sent/Submitted Notes: Submitted By: Email Address: Riley Tobin rtobin@pavilionconstruction.com Phone: Fax: (503)290-5005 (503)244-1810 SUBMITTAL RESPONSE Architect s Response Schedule Tracking Proceed Proceed, as noted Revise and Resubmit Material Return without Review Date Date Date Date Received from Sub/Sup Requested to be returned Returned from Architect Returned to Sup/Sup 07/09/2015 07/13/2015 Comments: PAVILION CONSTR JCTION LLC o APPROVEDAS SUBMITTEO o OISAPPROVEO, PlIASE SUBMIT COPlES ory: _Riley APPRDVEOAS NOTEO o 7/9/15 _ Tobin DATED: F()R THE RECORD 06/23/15 This submittal has been reviewed for general "onformil."'.ce with ttle contract documents. Tn's review does not reuevs the supplier of responsibility for erro~, omissions or any dtviition tram the requirements of the ",.....r?c! :!vr:umems. Mike Harmel 07.13.2015 Pavilion Construction NW, LLC 4700 SW Macadam Ave. Portland, OR 97239 Phone: (503)290-5005 Fax: (503)244-1810 www.pavilionconstruction.com Page 1 of 1

Sunset High School - Title IX and Upgrades Beaverton School District No. 48 BLRB Project No.: 14.84P Permit Set May 15, 2015 SECTION 10 51 13 - METAL LOCKERS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections, apply to this Section. 1.2 SUMMARY A. Section Includes: 1. Knocked-down athletic lockers. 2. Welded athletic lockers. 1.3 PREINSTALLATION MEETINGS A. Preinstallation Conference: Conduct conference at Project site. 1.4 ACTION SUBMITTALS A. Product Data: For each type of metal locker. 1. Include construction details, material descriptions, dimensions of individual components and profiles, and finishes for each type of metal locker. B. Shop Drawings: For metal lockers. 1. Include plans, elevations, sections, details, and attachments to other work. 2. Show locker trim and accessories. 3. Include locker identification system and numbering sequence. C. Samples: For each color specified, in manufacturer's standard size. D. Samples for Initial Selection: Manufacturer's color charts showing the full range of colors available. E. Samples for Verification: For the following products, in manufacturer's standard size: 1. Lockers and equipment. 2. Locker benches. F. Product Schedule: For lockers. 1.5 INFORMATIONAL SUBMITTALS A. Qualification Data: For Installer. B. Sample Warranty: For special warranty. BLRB Architects - Portland, Oregon METAL LOCKERS 10 51 13-1

Sunset High School - Title IX and Upgrades Beaverton School District No. 48 BLRB Project No.: 14.84P Permit Set May 15, 2015 1.6 CLOSEOUT SUBMITTALS A. Maintenance Data: For adjusting, repairing, and replacing locker doors and latching mechanisms to include in maintenance manuals. 1.7 MAINTENANCE MATERIAL SUBMITTALS A. Furnish extra materials that match products installed and that are packaged with protective covering for storage and identified with labels describing contents. 1. Full-size units of the following metal locker hardware items equal to 10 percent of amount installed for each type and finish installed, but no fewer than five units: 2. Locks. a. Identification plates. b. Hooks. 1.8 DELIVERY, STORAGE, AND HANDLING A. Do not deliver metal lockers until spaces to receive them are clean, dry, and ready for their installation. 1.9 FIELD CONDITIONS A. Field Measurements: Verify actual dimensions of recessed openings by field measurements before fabrication. 1.10 COORDINATION A. Coordinate sizes and locations of concrete bases for metal lockers. B. Coordinate sizes and locations of framing, blocking, furring, reinforcements, and other related units of work specified in other Sections to ensure that metal lockers can be supported and installed as indicated. 1.11 WARRANTY A. Special Warranty: Manufacturer agrees to repair or replace components of metal lockers that fail in materials or workmanship, excluding finish, within specified warranty period. 1. Failures include, but are not limited to, the following: a. Structural failures. b. Faulty operation of latches and other door hardware. 2. Damage from deliberate destruction and vandalism is excluded. 3. Warranty Period for Knocked-Down Metal Lockers: Two years from date of Substantial Completion. 4. Warranty Period for Welded Metal Lockers: Lifetime from date of Substantial Completion. BLRB Architects - Portland, Oregon METAL LOCKERS 10 51 13-2

Sunset High School - Title IX and Upgrades Beaverton School District No. 48 BLRB Project No.: 14.84P Permit Set May 15, 2015 PART 2 - PRODUCTS 2.1 MANUFACTURERS A. Source Limitations: Obtain metal lockers and accessories from single source from single locker manufacturer. 1. Obtain locks from single lock manufacturer. 2.2 PERFORMANCE REQUIREMENTS A. Accessibility Requirements: For lockers indicated to be accessible, comply with applicable provisions in the U.S. Architectural & Transportation Barriers Compliance Board's ADA-ABA Accessibility Guidelines and ICC A117.1. 2.3 KNOCKED-DOWN ATHLETIC LOCKERS A. Basis-of-Design Product: Subject to compliance with requirements, provide Republic Storage Systems, LLC; Heavy Duty Ventilated or a comparable product by one of the following: 1. Art Metal Products. 2. Lyon Workspace Products, LLC. 3. Penco Products, Inc. B. Perforated Doors: One piece; fabricated from 0.075-inch nominal-thickness steel sheet with manufacturer's standard diamond perforations; formed into channel shape with double bend at vertical edges and with right-angle single bend at horizontal edges and latch point (bottom) and right-angle single bend at remaining edges for box lockers. 1. Reinforcement: Manufacturer's standard reinforcing angles, channels, or stiffeners for doors more than 15 inches wide; welded to inner face of doors. C. Body: Assembled by riveting or bolting body components together. Fabricate from unperforated steel sheet with thicknesses as follows: 1. Tops and Bottoms: 0.060-inch nominal thickness, with single bend at edges. 2. Backs: 0.048-inch nominal thickness. 3. Shelves: 0.060-inch nominal thickness, with double bend at front and single bend at sides and back. D. Unperforated Sides: Fabricated from 0.060-inch nominal-thickness steel sheet. E. Frames: Channel formed; fabricated from 0.060-inch nominal-thickness steel sheet or 0.097-inch nominal-thickness steel angles; lapped and factory welded at corners; with top and bottom main frames factory welded into vertical main frames. Form continuous, integral, full-height door strikes on vertical main frames. 1. Cross Frames for Double-Tier and Triple-Tier Lockers: Channel formed and fabricated from same material as main frames; welded to vertical main frames. F. Hinges: Welded to door and attached to door frame with no fewer than two factory-installed rivets per hinge that are completely concealed and tamper resistant when door is closed; fabricated to swing 180 degrees. 1. Knuckle Hinges: Steel, full loop, five or seven knuckles, tight pin; minimum 2 inches high. Provide no fewer than three hinges for each door more than 42 inches high. BLRB Architects - Portland, Oregon METAL LOCKERS 10 51 13-3

Sunset High School - Title IX and Upgrades Beaverton School District No. 48 BLRB Project No.: 14.84P Permit Set May 15, 2015 G. Door Handle and Latch: Stainless-steel strike plate with integral pull; with steel padlock loop that projects through metal locker door. H. Identification Plates: Manufacturer's standard, etched, embossed, or stamped aluminum plates, with numbers and letters at least 3/8 inch high. I. Hooks: Manufacturer's standard ball-pointed type, aluminum or steel; zinc plated. J. Coat Rods: Manufacturer's standard. K. Continuous Sloping Tops: Fabricated from 0.048-inch nominal-thickness steel sheet, with a pitch of approximately 20 degrees. 1. Closures: Vertical-end type. L. Filler Panels: Fabricated from 0.048-inch nominal-thickness steel sheet. M. Boxed End Panels: Fabricated from 0.060-inch nominal-thickness steel sheet. N. Materials: 1. Cold-Rolled Steel Sheet: ASTM A 1008/A 1008M, Commercial Steel (CS), Type B, suitable for exposed applications. O. Finish: Baked enamel or powder coat. 1. Color: As selected by Architect from manufacturer's full range. 2.4 WELDED ATHLETIC LOCKERS A. Basis-of-Design Product: Subject to compliance with requirements, provide Republic Storage Systems, LLC; All-Welded Ventilated or a comparable product by one of the following: 1. Art Metal Products. 2. Lyon Workspace Products, LLC. 3. Penco Products, Inc. B. Perforated Doors: One piece; fabricated from 0.075-inch nominal-thickness steel sheet with manufacturer's standard diamond perforations; formed into channel shape with double bend at vertical edges and with right-angle single bend at horizontal edges and latch point (bottom) and right-angle single bend at remaining edges for box lockers. 1. Reinforcement: Manufacturer's standard reinforcing angles, channels, or stiffeners for doors more than 15 inches wide; welded to inner face of doors. C. Body: Assembled by welding body components together. Fabricate from unperforated steel sheet with thicknesses as follows: 1. Tops and Bottoms: 0.060-inch nominal thickness, with single bend at edges. 2. Backs: 0.048-inch nominal thickness. 3. Shelves: 0.060-inch nominal thickness, with double bend at front and single bend at sides and back. D. Unperforated Sides: Fabricated from 0.060-inch nominal-thickness steel sheet. E. Frames: Channel formed; fabricated from 0.060-inch nominal-thickness steel sheet or 0.097-inch nominal-thickness steel angles; lapped and factory welded at corners; with top and bottom main frames factory welded into vertical main frames. Form continuous, integral, full-height door strikes on vertical main frames. BLRB Architects - Portland, Oregon METAL LOCKERS 10 51 13-4

Sunset High School - Title IX and Upgrades Beaverton School District No. 48 BLRB Project No.: 14.84P Permit Set May 15, 2015 1. Cross Frames for Double-Tier and Triple-Tier Lockers: Channel formed and fabricated from same material as main frames; welded to vertical main frames. F. Hinges: Welded to door and attached to door frame with no fewer than two factory-installed rivets per hinge that are completely concealed and tamper resistant when door is closed; fabricated to swing 180 degrees. 1. Knuckle Hinges: Steel, full loop, five or seven knuckles, tight pin; minimum 2 inches high. Provide no fewer than three hinges for each door more than 42 inches high. G. Door Handle and Latch: Stainless-steel strike plate with integral pull; with steel padlock loop that projects through metal locker door. H. Identification Plates: Manufacturer's standard, etched, embossed, or stamped aluminum plates, with numbers and letters at least 3/8 inch high. I. Hooks: Manufacturer's standard ball-pointed type, aluminum or steel; zinc plated. J. Coat Rods: Manufacturer's standard. K. Continuous Sloping Tops: Fabricated from 0.048-inch nominal-thickness steel sheet, with a pitch of approximately 20 degrees. 1. Closures: Vertical-end type. L. Filler Panels: Fabricated from 0.048-inch nominal-thickness steel sheet. M. Boxed End Panels: Fabricated from 0.060-inch nominal-thickness steel sheet. N. Materials: 1. Cold-Rolled Steel Sheet: ASTM A 1008/A 1008M, Commercial Steel (CS), Type B, suitable for exposed applications. O. Finish: Baked enamel or powder coat. 1. Color: As selected by Architect from manufacturer's full range. 2.5 FABRICATION A. Fabricate metal lockers square, rigid, without warp, and with metal faces flat and free of dents or distortion. Make exposed metal edges safe to touch and free of sharp edges and burrs. 1. Form body panels, doors, shelves, and accessories from one-piece steel sheet unless otherwise indicated. 2. Provide fasteners, filler plates, supports, clips, and closures as required for complete installation. B. Fabricate each metal locker with an individual door and frame; individual top, bottom, and back; and common intermediate uprights separating compartments. Factory weld frame members of each metal locker together to form a rigid, one-piece assembly. C. Equipment: Provide each locker with an identification plate and the following equipment: 1. Single-Tier Units: Shelf, one double-prong ceiling hook, and two single-prong wall hooks. 2. Double-Tier Units: One double-prong ceiling hook and two single-prong wall hooks. 3. Triple-Tier Units: One double-prong ceiling hook. 4. Coat Rods: For each compartment of each locker. BLRB Architects - Portland, Oregon METAL LOCKERS 10 51 13-5

Sunset High School - Title IX and Upgrades Beaverton School District No. 48 BLRB Project No.: 14.84P Permit Set May 15, 2015 D. Knocked-Down Construction: Fabricate metal lockers using nuts, bolts, screws, or rivets for nominal assembly at Project site. E. Welded Construction: Factory preassemble metal lockers by welding all joints, seams, and connections; with no bolts, nuts, screws, or rivets used in assembly of main locker groups. Factory weld main locker groups into one-piece structures. Grind exposed welds flush. F. Accessible Lockers: Fabricate as follows: 1. Locate bottom shelf no lower than 15 inches above the floor. 2. Where hooks, coat rods, or additional shelves are provided, locate no higher than 48 inches above the floor. G. Continuous Base: Formed into channel or zee profile for stiffness, and fabricated in lengths as long as practical to enclose base and base ends of metal lockers; finished to match lockers. H. Continuous Sloping Tops: Fabricated in lengths as long as practical, without visible fasteners at splice locations; finished to match lockers. 1. Sloping-top corner fillers, mitered. I. Individual Sloping Tops: Fabricated in width to fit one locker frame in lieu of flat locker tops; with integral back; finished to match lockers. Provide wedge-shaped divider panels between lockers. J. Recess Trim: Fabricated with minimum 2-1/2-inch face width and in lengths as long as practical; finished to match lockers. K. Filler Panels: Fabricated in an unequal leg angle shape; finished to match lockers. Provide slip-joint filler angle formed to receive filler panel. L. Boxed End Panels: Fabricated with 1-inch-wide edge dimension, and designed for concealing fasteners and holes at exposed ends of nonrecessed metal lockers; finished to match lockers. 1. Provide one-piece panels for double-row (back-to-back) locker ends. M. Finished End Panels: Designed for concealing unused penetrations and fasteners, except for perimeter fasteners, at exposed ends of nonrecessed metal lockers; finished to match lockers. 1. Provide one-piece panels for double-row (back-to-back) locker ends. N. Center Dividers: Full-depth, vertical partitions between bottom and shelf; finished to match lockers. 2.6 ACCESSORIES A. Fasteners: Zinc- or nickel-plated steel, slotless-type, exposed bolt heads; with self-locking nuts or lock washers for nuts on moving parts. B. Anchors: Material, type, and size required for secure anchorage to each substrate. 1. Provide nonferrous-metal or hot-dip galvanized anchors and inserts on inside face of exterior walls for corrosion resistance. 2. Provide toothed-steel or lead expansion sleeves for drilled-in-place anchors. BLRB Architects - Portland, Oregon METAL LOCKERS 10 51 13-6

Sunset High School - Title IX and Upgrades Beaverton School District No. 48 BLRB Project No.: 14.84P Permit Set May 15, 2015 PART 3 - EXECUTION 3.1 EXAMINATION A. Examine walls, floors, and support bases, with Installer present, for compliance with requirements for installation tolerances and other conditions affecting performance of the Work. B. Prepare written report, endorsed by Installer, listing conditions detrimental to performance of the Work. C. Proceed with installation only after unsatisfactory conditions have been corrected. 3.2 INSTALLATION A. General: Install lockers level, plumb, and true; shim as required, using concealed shims. 1. Anchor locker runs at ends and at intervals recommended by manufacturer, but not more than 36 inches o.c. Using concealed fasteners, install anchors through backup reinforcing plates, channels, or blocking as required to prevent metal distortion. 2. Anchor single rows of metal lockers to walls near top of lockers and to floor. 3. Anchor back-to-back metal lockers to floor. B. Knocked-Down Lockers: Assemble with standard fasteners, with no exposed fasteners on door faces or face frames. C. Welded Lockers: Connect groups together with standard fasteners, with no exposed fasteners on face frames. D. Equipment: 1. Attach hooks with at least two fasteners. 2. Attach door locks on doors using security-type fasteners. 3. Identification Plates: Identify metal lockers with identification indicated on Drawings. a. Attach plates to each locker door, near top, centered, with at least two aluminum rivets. b. Attach plates to upper shelf of each open-front metal locker, centered, with a least two aluminum rivets. E. Trim: Fit exposed connections of trim, fillers, and closures accurately together to form tight, hairline joints, with concealed fasteners and splice plates. 1. Attach recess trim to recessed metal lockers with concealed clips. 2. Attach filler panels with concealed fasteners. Locate filler panels where indicated on Drawings. 3. Attach sloping-top units to metal lockers, with closures at exposed ends. 4. Attach boxed end panels using concealed fasteners to conceal exposed ends of nonrecessed metal lockers. 5. Attach finished end panels using fasteners only at perimeter to conceal exposed ends of nonrecessed metal lockers. F. Fixed Locker Benches: Provide no fewer than two pedestals for each bench, uniformly spaced not more than 72 inches apart. Securely fasten tops of pedestals to undersides of bench tops, and anchor bases to floor. G. Freestanding Locker Benches: Place benches in locations indicated on Drawings. BLRB Architects - Portland, Oregon METAL LOCKERS 10 51 13-7

Sunset High School - Title IX and Upgrades Beaverton School District No. 48 BLRB Project No.: 14.84P Permit Set May 15, 2015 3.3 ADJUSTING A. Clean, lubricate, and adjust hardware. Adjust doors and latches to operate easily without binding. 3.4 PROTECTION A. Protect metal lockers from damage, abuse, dust, dirt, stain, or paint. Do not permit use during construction. B. Touch up marred finishes, or replace metal lockers that cannot be restored to factory-finished appearance. Use only materials and procedures recommended or furnished by locker manufacturer. END OF SECTION 10 51 13 BLRB Architects - Portland, Oregon METAL LOCKERS 10 51 13-8

25 82 nd Drive, Ste. 200 Gladstone OR 97207 Sunset HS List lockers Submittal package with dimensional notes. Type A and C lockers are All-Welded. These will come in pre-welded cabinets. Refer to cut sheet showing grouping (A1, A2, and A3). The maximum width on an 18 wide door is 3 locker frames wide (53-15/16 ). Lockers need to have a maximum of ½ overhang, we normally see the bases about a ½ short on width and length to allow for some kind of overhang this is an architectural preference. - On this particular project all exposed ends receive a 1 boxed end panel, this needs to be added at ALL exposed ends. The attached drawings have this calculated into the dimensions. - We have filler panels that we typically use on all projects, they are 6 wide and are cut down in the field as needed. A 6 wide filler can be cut down to as little as 2. The attached dimensions show exactly what the lockers would take to fit, I suggest adding 4 which will allow the use of a filler if the space in the room can accommodate. Type B and D lockers are KD (Knock Down) and assembled in the field. I did not put the dimensions on the attached drawings for these areas. These are much more simple Add 1/32 growth per locker frame and 1 @ each exposed end. Same rules would apply for the fillers. www.northwest-school-eq.com

SUPERIOR Heavy-Duty Ventilated (HDV) KD Wardrobe and Box Lockers General: Lockers shall be "Superior Heavy-Duty Ventilated (HDV) KD Wardrobe and Box Lockers" as manufactured by List Industries Inc. or approved equal. Fabricate lockers square, rigid and without warp, with metal faces flat and free from dents or distortion. Make all exposed metal edges safe to touch. Weld frame members together to form rigid, one-piece structure. Weld, bolt, or rivet other joints and connections as standard with manufacturer. Grind exposed welds flush. Do not expose bolts or rivet heads on fronts of locker doors or frames except for fastening of number plates and recessed handle. Lockers shall be GREENGUARD Children & Schools Certified SM Finishing: All locker parts to be cleaned and coated after fabrication with a seven stage zinc/iron phosphate solution to inhibit corrosion, followed by a coat of high grade custom blend powder electrostatically sprayed and baked at 350 degrees Fahrenheit for a minimum of 20 minutes to provide a tough durable finish. Color to be selected from manufacturer's standard list of colors. Interior components are to be painted choice of #729 Parchment or #725 Hallowell Gray. Two-Tone Color Combination: Shall be at no additional cost with the locker frame and trim chosen from one color and the doors may be one of any other color chosen from manufacturers standard selection. Frame: Fabricate of 16 gauge (minimum) channels, with integral continuous door stop/strike formed on both latch and hinge side vertical members. Cross frame members of 16 gauge channel shapes, including intermediate cross frame members on double and triple tier (frames with doors over 18" high) lockers shall be securely welded to the vertical framing members to ensure rigidity. Rubber bumpers shall be provided to cushion door closing. HDV Wardrobe Doors: Doors 20 high and higher shall be fabricated from single sheet prime 14 gauge with single bends at top and bottom and double bends at the sides. The channel formed by the double bend at the latch side is designed to fully conceal the lock bar. Doors are to be perforated with 5/8 x 1-1/2 diamonds. HDV Box Doors: Doors 18" high and under to be fabricated from single sheet prime 14 gauge with single bends at top, bottom and sides. Doors shall include a combination friction catch door pull. Padlock Strike Plates are optional. Doors shall be fabricated to accept a built-in combination lock or padlock. Doors with projecting spring latches shall not be acceptable. Doors are to be perforated with 7/16 x 15/16 diamonds. Stainless Steel Recessed Locker Handle: All wardrobe doors shall have recessed not less than 304 stainless steel handle shaped to receive a padlock or built-in combination lock. The recess pan shall be deep enough to have the lock be flush with the outer door face. Box doors shall be equipped with a combination friction catch door pull as stated above. 04/13/10

SUPERIOR Heavy-Duty Ventilated (HDV) KD Wardrobe and Box Lockers (Page 2) Latch Assembly: The latching mechanism for wardrobe doors shall be finger lift control type constructed of 14 gauge (minimum) steel with a nylon cover that has a generous finger pull. Spring activated nylon slide latches shall be completely enclosed in the lock channel allowing doors to close with the lock in the locked position. Lock bar shall be hot dip galvanized and install after paint to ensure proper paint coverage and lock bar operation. Locking devise shall be designed for use with either built-in combination locks or padlocks. Latch hooks shall be securely welded to the vertical frame channel on the strike side to engage the nylon slide latches. Three latch hooks for doors 48" and higher, two latch hooks for doors under 48" high. Door Hinges: All doors shall include a 16 gauge continuous piano hinge welded to the door and riveted to the frame. All doors to be right hand, side hinged. Body: Fabricate backs of 18 gauge (minimum) solid sheet, sides of 16 gauge (minimum) sheet steel with double flanged connections extending full height. Sides to be diamond perforated for added ventilation. Form top, bottom and intermediate tier dividers of 16 gauge (minimum) solid sheet steel with single return bends at all sides. Bolt top and bottom as well as horizontal tier dividers of wardrobe openings to front horizontal frame members at not less than one place in addition to side panels. Form hat shelves at 60 and 72 high single tier lockers of 16 gauge (minimum) sheet steel with single bends at sides and back and a double bend at front. Locks (If required): Shall be master-keyed to one system for the entire project. (See lock use chart for suggested lock application) Equipment: Furnish each locker with the following items, unless otherwise shown. Single tier lockers: Openings 60 and 72 shall include one hat shelf, one double prong ceiling hook and a minimum of two single prong hooks. Double tier lockers: Openings 30 and 36 high shall include one double prong ceiling hook and a minimum of two single prong hooks. Triple tier lockers: Openings 20 and 24 high shall include one double prong ceiling hook only. Box lockers: No hooks Two-Year Warranty: Superior KD lockers are covered against all defects in materials and workmanship excluding finish, damage resulting from deliberate destruction and vandalism under this section for a period of two years. 04/13/10

SUPERIOR Fully-Framed All-Welded P.E. and Team Lockers General: Lockers shall be "Superior Fully-Framed All-Welded Team & P.E. Athletic Lockers" as manufactured by List Industries Inc. or approved equal. All lockers shall be factory-assembled, of all MIG welded construction, in multiple column units to meet job conditions. Assembly of locker bodies by means of bolts, screws, or rivets will not be permitted. Welding of knockdown locker construction is not acceptable. Grind exposed welds and metal edges flush and make safe to touch. Lockers shall be GREENGUARD Children & Schools Certified SM Finishing: All locker parts to be cleaned and coated after fabrication with a seven stage zinc/iron phosphate solution to inhibit corrosion, followed by a coat of high grade custom blend powder electrostatically sprayed and baked at 350 degrees Fahrenheit for a minimum of 20 minutes to provide a tough durable finish. Color to be selected from manufacturer's standard list of colors. Two-Tone Color Combination: Shall be at no additional cost with the locker body, frame and trim chosen from one color and the doors may be one of any other color chosen from manufacturers standard selection. Frame / Vertical Side panels: Shall be of 13 gauge ½ flattened expanded metal framed by 16 gauge Hollow "T" tubular sections and channel frame members designed to enclose all four edges of the side panel with the entire assembly MIG welded to form a rigid frame for each locker. The channel frame members are welded to the front and rear vertical frame members to create and anchor bearing surface of 1-1/4 inches wide x the depth of the locker at each side panel. Integral Frame Locker base: 14 gauge formed structural channels are MIG welded to the front and rear vertical side panel frame members to allow placement of locker bottom a minimum 2-3/4" above floor level. Locker bottom shelf located less than 2 above floor level will not be acceptable. Team Wardrobe Doors: Doors 20" high and over and 15 wide and under are to be fabricated from single sheet prime 14 gauge with single bends at top and bottom and double bends at the sides. The channel formed by the double bend at the latch side is designed to fully conceal the lock bar. The latching mechanism shall be finger lift control type constructed of 14 gauge (minimum) steel with a nylon cover that has a generous finger pull. Lock bar shall be hot dip galvanized and installed after paint to ensure proper paint coverage and lock bar operation. Spring activated nylon slide latches shall be completely enclosed in the lock channel allowing doors to close with the lock in the locked position. Locking devise shall be designed for use with either built-in combination locks or padlocks. Latch hooks shall be 11 gauge (minimum) with riveted bumpers and shall be MIG welded to vertical frame member. Provide three latch hooks for doors 48" and over and two for doors under 48". Doors to be perforated with 5/8 x 1-1/2 diamonds. 06/13/11

SUPERIOR Fully-Framed All-Welded P.E. and Team Lockers (Page 2) P.E. Gym Doors 12 High And Under: Doors 12" high and under to be top hinged and be fabricated from single sheet prime 14 gauge with single bend at top and sides with a double bend at latch point (bottom). A spring loaded galvanized latch assembly shall be securely welded to the inside of the door. The latch shall be a minimum of 11 gauge, be equipped with a stainless steel spring and shall automatically engage when door is closed. Rubber bumpers shall be riveted to return bends on doors. Locking devise shall be designed for use with both a padlock and built-in lock. Padlock Strike Plates are optional. Doors to be perforated with 7/16 x 15/16 diamonds. P.E. Gym Doors 15 And 18 High: Doors 15 and 18" high to be side hinged and be fabricated from single sheet prime 14 gauge with single bend at top and bottom and double bends at hinge and latch sides. A spring loaded galvanized latch assembly shall be securely welded to the inside of the door. The latch shall be a minimum of 11 gauge, be equipped with a stainless steel spring and shall automatically engage an 11 gauge full height continuous door strike when the door is closed. The door strike is to be MIG welded to the frame. Rubber bumpers shall be riveted to return bends on doors. Locking devise shall be designed for use with both a padlock and built-in lock. Padlock Strike Plates are optional. Doors to be perforated with 7/16 x 15/16 diamonds. Seamless Drawn Locker Handle: All wardrobe doors 20 high and over shall have a seamless drawn not less than 304 stainless steel recessed handle shaped to receive a padlock or built-in combination lock. The recessed handle shall be deep enough to have the lock be completely flush with the outer door face. Door Hinges: Hinges for wardrobe and side hinged gym doors shall not be less than 3-1/2" long 13 gauge seven knuckle pin type, securely riveted to frame and welded to the door. Doors are to be secured to frame with a minimum of two tamper resistant rivets per hinge. Provide 3 hinges for doors 48" and higher and 2 for doors shorter than 48". All doors shall be right hand side hinged except top hinged gym doors as noted above. Top hinged gym doors shall be hinged using a 3/16" diameter continuous hinge rod completely recessed into the door with a concealed fastener. Flat Tops: Shall be formed of one piece of 16 gauge cold rolled sheet steel and shall be an integral part MIG welded to each vertical side panel frame member and be continuous to cover the full width of a multiple framed locker unit. Hat Shelves, Intermediate Shelves and Bottoms: Shall be 16 gauge galvanneal sheet steel, have double bends at front and shall engage slots in the Hollow "T" vertical frame members at all four corners and be securely welded to the frame and side. Locker bottom shelf located less than 2 above floor level will not be acceptable. Backs: Shall be 18 gauge cold rolled sheet steel, be continuous to cover a multiple framed unit and be welded to each vertical side panel frame member. 06/13/11

SUPERIOR Fully-Framed All-Welded P.E. and Team Lockers (Page 3) Locks (If required): Shall be master keyed to one system for the entire project. (See lock use chart for suggested lock application). Equipment: Furnish each locker with the following items, unless otherwise shown. Single tier lockers: Openings 60 and 72 shall include one galvanneal hat shelf, one double prong ceiling hook and a minimum of two single prong hooks. Double and triple tier lockers: Openings 20 thru 36 high shall include one double prong ceiling hook and a minimum of two single prong hooks. Box lockers: No hooks Lifetime Warranty: Superior Fully-Framed All-Welded Lockers are covered against all defects in materials and workmanship excluding finish, damage resulting from deliberate destruction and vandalism under this section for the lifetime of the facility. 06/13/11

Submittal Review TO: Pavilion Construction DATE: 07.01.2015 JOB NO.: 1484P 4700 SW Macadam Ave Suite 200 ATTENTION: Riley Tobin Portland, OR 97239 RE: BSD Sunset High School Concession Stand/Interior Renovations Package 1 Submittal: 105113 Metal Lockers Informational Submittal Approved Approved As Noted Revise as Noted/Resubmit Rejected/Resubmit As Specified No Action Required Submittal Not Requested/Returned Without Review Approval is for conformance with information given and the design concept expressed in the Contract Documents. Contractor is responsible for quantities and dimensions to be confirmed and correlated; for fabrication process; for means methods, techniques, sequences and procedures of construction; for coordination of the Work; and for all safety aspects of performing the Work. Approval does not modify the Contract Documents and approval of a specific item does not indicate approval of an assembly of which the item is a component. Specification Section Title Notation 105113 1.4A Product Data Reviewed in Separate Submittal 105113 1.4B Shop Drawings Reviewed in Separate Submittal 105113 1.4C Samples For Each Color Selected Reviewed in Separate Submittal 105113 1.4D Samples For Initial Selection Reviewed in Separate Submittal 105113 1.4E Samples For Verification Reviewed in Separate Submittal 105113 1.4 F Product Schedule Reviewed in Separate Submittal 105113 1.5A Qualification Data Approved 105113 1.5B Sample Warranty Approved 1001 SW 5 th Ave. // Suite 1100 // Portland // OR 97204-1127 // P: 503.535.0707 // www.blrb.com

Sunset High School 13840 NW Cornell Rd. Portland, OR 97229 To: Attn: BLRB ARCHITECTS, P.S. RICHARD HIGGINS 1001 SW 5TH AVE., SUITE 1100 PORTLAND, OR 97204 Date: Contact Phone: Contact Email: 06/30/2015 503-535-0707 RHIGGINS@BLRB.COM CC d: SUBMITTAL TRANSMITTAL FOR APPROVAL Submittal #: 42.1 Rev.#: 0 In Accordance with Specification Section #: 105113 This is a submittal for Metal Lockers items per the table below as reviewed and noted by Pavilion Construction NW, LLC, and provided by. Please provide a response to this submittal by 07/02/2015. Pavilion Status: Sent/Submitted Notes: Submitted By: Email Address: Riley Tobin rtobin@pavilionconstruction.com Phone: Fax: (503)290-5005 (503)244-1810 SUBMITTAL RESPONSE Architect s Response Proceed Proceed, as noted Revise and Resubmit Material Return without Review Schedule Tracking Date Date Date Date Received from Sub/Sup Requested to be returned Returned from Architect Returned to Sup/Sup 06/30/2015 07/02/2015 Comments: PAVILION CONSTR JCTION LLC o APPROVEDAS SUBMITTEO o OISAPPROVEO, PlIASE SUBMIT COPlES ory: _APPRDVEOAS NOTEO o 06/30/15 DATED: _ F()R THE RECORD _ 06/23/15 Riley Tobin This submittal has been reviewed for general "onformil."'.ce with ttle contract documents. Tn's review does not reuevs the supplier of responsibility for erro~, omissions or any dtviition tram the requirements of the ",.....r?c! :!vr:umems. Mike Harmel 07.01.2015 Pavilion Construction NW, LLC 4700 SW Macadam Ave. Portland, OR 97239 Phone: (503)290-5005 Fax: (503)244-1810 www.pavilionconstruction.com Page 1 of 1

SUPERIOR FULLY-FRAMED ALL WELDED LOCKERS LIFETIME WARRANTY To: Sample Project: Sample LIST INDUSTRIES, INC. JOB: Sample Substantial Completion Date: Sample Superior Fully-Framed Lockers carry a lifetime warranty against defect in materials and workmanship. Rust resulting from excessive use of cleaning agents, exposed to water from open doors and windows or roof leaks, improper ventilation causing high humidity, and chlorine saturated bathing suits will not be covered by this warranty. The warranty only applies to components manufactured by List Industries Inc. and excludes those items such as locks, wood bench-tops, cast iron pedestals, etc. Damage resulting from deliberate destruction, vandalism, shipping or faulty installation is not covered by this warranty. Any repairs, adjustments or replacements to be made under this warranty shall be performed only upon authorization in writing by List Industries Inc. 401 Jim Moran Blvd, P.O. Box 9601, Deerfield Beach, FL 33442 tel 954-429-9155 fax 954-428-3843 www.listindustries.com