An Analysis of Structural and Optical Properties Undoped ZnS and Doped (with Mn, Ni) ZnS Nano Particles

Similar documents
Optical studies of CdS Nanoparticles prepared by CBD Method

Ibn Al-Haitham Jour. for Pure & Appl. Sci Vol. 32 (1) 2019

CHAPTER 4. SYNTHESIS OF ALUMINIUM SELENIDE (Al 2 Se 3 ) NANO PARTICLES, DEPOSITION AND CHARACTERIZATION

CHAPTER 8 CONCLUSIONS AND SCOPE FOR FUTURE WORK

Selective growth of Au nanograins on specific positions (tips, edges. heterostructures.

Studies on Structural and Optical Properties of Iron doped Cds Nanoparticles ABSTRACT

Mn DOPED SnO2 Semiconducting Magnetic Thin Films Prepared by Spray Pyrolysis Method

GROWTH AND CHARACTERIZATION OF NANOSTRUCTURED CdS THIN FILMS BY CHEMICAL BATH DEPOSITION TECHNIQUE

for New Energy Materials and Devices; Beijing National Laboratory for Condense Matter Physics,

Synthesis and Characterization of Cadmium Sulfide Nanoparticles

Biomimetic synthesis of gold nanocrystals using a reducing amphiphile. Ferdinand Gonzaga, Sherdeep Singh and Michael A. Brook. Department of Chemistry

Chapter 4 SYNTHESIS AND CHARACTERIZATION OF MAGNISIUM OXIDETRANSITION METAL OXIDE NANOCOMPOSITES

Optical parameter determination of ZrO 2 thin films prepared by sol gel dip coating

Supplementary Information

STUDY OF CHEMICAL BATH DEPOSITED NANOCRYSTALLINE CdZnS THIN FILMS

Supporting Information

Structure and Luminescence Properties of Y 2 O 3 :Eu 3+ Nanophosphors

SYNTHESIS, CHARACTERIZATION AND PHOTOCATALYTIC ACTIVITY OF MgO NANOPARTICLES

CHAPTER 3. Experimental Results of Magnesium oxide (MgO) Thin Films

Comparative studies on XRD and band gap of thin films of gel grown, doped and undoped PbI 2, and pure powder of PbI 2

QUANTUM SIZE EFFECT IN CHEMOSYNTHESIZED NANOSTRUCTURED CdS THIN FILMS

Preparation and characterization of Co BaTiO 3 nano-composite films by the pulsed laser deposition

Structure and optical properties of M/ZnO (M=Au, Cu, Pt) nanocomposites

Electronic Supplementary Information (ESI) available for:

CHAPTER 4 SYNTHESIS, CHARACTERIZATION AND MICROENCAPSULATION PROCESS OF THE NANO SILICA

Preparation and Characterization of Copper Oxide -Water Based Nanofluids by One Step Method for Heat Transfer Applications

SUPPLEMENTARY INFORMATION

EFFECT OF GROWTH TEMPERATURE ON THE CATALYST-FREE GROWTH OF LONG SILICON NANOWIRES USING RADIO FREQUENCY MAGNETRON SPUTTERING

Mahasin F. Hadi Al-Kadhemy, Sarah Hamid Nawaf Department of Physics, College of Science, Al-Mustansiriyah University, Iraq.

Effect of Ni 2+ doping on structural, morphological and optical properties of ZnS nanoparticles

Supplementary Figure 1 TEM of external salt byproducts. TEM image of some salt byproducts precipitated out separately from the Si network, with

Influence of annealing temperature on properties of nanocrystalline CdO thin films synthesized via thermal oxidation process

Influence of In/Sn ratio on nanocrystalline indium tin oxide thin films by spray pyrolysis method

Effect of RE Dopant (Ce & Tb) on PL and Crystallites size of Lanthanum Phosphor (LaPO 4 )

Structural and Optical Properties of MnO 2 : Pb Nanocrystalline Thin Films Deposited By Chemical Spray Pyrolysis

The Effect of Annealing Heat Treatment on Structural and Optical Properties of Ce-doped ZnO Thin Films

CORROSION BEHAVIOUR OF TOMBAC USED IN CULT OBJECTS MANUFACTURING

Electronic Supplementary Information

Growth Of TiO 2 Films By RF Magnetron Sputtering Studies On The Structural And Optical Properties

Optical Properties of Cerium Ferrite

Supporting Information. Solution-Processed 2D PbS Nanoplates with Residual Cu 2 S. Exhibiting Low Resistivity and High Infrared Responsivity

STRUCTURAL AND OPTOELECTRONIC PROPERTIES OF PYRALYTICALLY SPRAYED CdZnS THIN FILMS

Supporting Information

Photoluminescence and Thermoluminescence of Eu doped LAG phosphor

Synthesis and Characterization of Zinc Iron Sulphide (ZnFeS) Of Varying Zinc Ion Concentration

Chapter 5. Influence of Pb 2+ doping on photoluminescence properties CaSiO 3 : Mn 2+ nanophosphor

Synthesis and characterization of a narrowband Ca 5 (PO 4 ) 3 (OH):Gd 3+, Pr 3+ phosphor for medical applications

ISSN: [HOROZ * et al., 7(1): January, 2018] Impact Factor: 5.164

Chemically Tunable Full Spectrum Optical Properties of 2D Silicon Telluride Nanoplates

Structural, Optical, Morphological and Elemental Analysis on Sol-gel Synthesis of Ni Doped TiO2 Nanocrystallites

Supporting Information

Electronic Supplementary Information. Electrospinning Preparation and Upconversion Luminescence of Yttrium Fluoride Nanofibers

Supporting Information for The Influence of the CTAB Surfactant on the Colloidal Seed-Mediated Synthesis of Gold Nanorods

Time resolved spectroscopic studies on some nanophosphors

Red luminescence from Si quantum dots embedded in SiO x films grown with controlled stoichiometry

Characterization of SrAlO:Dy nano phosphors

Synthesis and Characterization of nanocrystalline Ni-Co-Zn ferrite by Sol-gel Auto-Combustion method.

Particle Size Effect on the Properties of Cerium Oxide (CeO2) Nanoparticles Synthesized by Hydrothermal Method 30

Structural and Optical Properties of Aluminium Antimonide Thin Films Deposited By Thermal Evaporation Method

Effect of Doping Concentration on the Structural Properties of Zn: SnO 2

LUMINESCENCE PERFORMANCE OF RED PHOSPHOR K 2 ZnSiO 4 : Eu 3+ FOR BLUE CHIP

Effects of different metal ion doping on nano crystalline LiMn 2 O 4 as cathodes for Lithium ions batteries

TSL-EPR Correlation Study of LaPO 4 : Ce, Tb

EFFECT OF MANGANESE SUBSTITUTION ON Co Ga AND Co Tl FERRITE NANOPARTICLES PREPARED BY HYDROTHERMAL ROUTE

Structural and optical properties of Cerium oxide nanoparticles

Ultra-low-temperature growth of CdS quantum dots on g-c 3 N 4. nanosheets and their photocatalytic performance

Specimen Preparation Technique for a Microstructure Analysis Using the Focused Ion Beam Process

Supplementary Information

Synthesis and Characterization of Cadmium Sulfide (CdS) Quantum Dots (QDS) for Quantum Dot Sensitized Solar Cell Applications

Effect of deposition parameters on Structural and Optical Properties of ZnS Thin Films

Luminescence Properties of Eu 2+ Doped Ca-α-SiAlON Phosphor. Li Li 1,a, Zhang Cheng 2,b, Feng Tao 3, Xu Haifeng 3, Li Qiang 1,c

Electronic Supplemental Information

Supporting Information:

Synthesis and characterization of Mn 2+ -doped ZnS nanoparticles

Magnetron Sputtering Coating of Protective Fabric Study on Influence of Thermal Properties

Polycrystalline and microcrystalline silicon

Anju Singh 1* and H. L. Vishwakarma 2

Experimental Study on Nitrogen-Doped Nano-Scale TiO 2 Prepared by Microwave-Assisted Process at Low Temperature

Large-scale Spinning of Silver Nanofibers as Flexible and. Reliable Conductors

Influence of Heat Treating for ZnS:Mn Sputtering Targets on Inorganic Electroluminescent Device Active Layer Films

Linlin Xin a and Xuefeng Liu b. School of Chemical and Material Engineering, Jiangnan University, Wuxi, , PR China.

Supporting Information. on Degradation of Dye. Chengsi Pan and Yongfa Zhu* Department of Chemistry, Tsinghua University, Beijing, , China

Controlled Fabrication and Optical Properties of Uniform CeO 2 Hollow Spheres

Department of Applied Chemistry, Faculty of Science and Technology, Keio University,

CHAPTER 8 SYNTHESIS AND CHARACTERIZATION OF COPPER DOPED NICKEL-MANGANESE MIXED FERRITE NANOPARTICLES BY CO-PRECIPITATION METHOD

Graphene/Fe 3 O Quaternary Nanocomposites: Synthesis and Excellent Electromagnetic Absorption Properties

Growth, Optical and Electrical Properties of zinc tris (thiourea) sulphate (ZTS) Single Crystals

Fabrication and Characterization of a Polypyrrole Coated Copper Nanowire Gas Sensor

PREPARATION OF VISIBLE-LIGHT-DRIVEN TIO 2 PHOTOCATALYST DOPED WITH IRON IN SUPERCRITICAL CARBON DIOXIDE

Heteroepitaxy of Monolayer MoS 2 and WS 2

Chalcogenide Letters Vol. 6, No. 11, November 2009, p

Supplementary Figure S1. High-resolution XPS spectra in the Cu 2p region and Cu LMM spectra are shown in (A) and (B) respectively for CdSe NCs

Studies on X doped (X = Al, Zn and Cu) and undoped Lead Iodide single crystals relating to XRD

Growth and Characterization of Cd 1-x Zn x Te Films

One-step route to Ag nanowires with diameter below 40 nm and. aspect ratio above 1000

Synthesis Photoluminescence and Thermoluminescence study of Ca 2 CeO 4 : Eu nano Phosphor

Supplimentary Information. Large-Scale Synthesis and Functionalization of Hexagonal Boron Nitride. Nanosheets

Lesson 1 X-rays & Diffraction

Mechanoluminescence Properties of Pure and Ag + (1-5%) doped (Cd 0.95 Zn 0.05 )S Phosphors

Optical, microstructural and electrical studies on sol gel derived TiO 2 thin films

Transcription:

Journal of Modern Physics, 213, 4, 122-126 http://dx.doi.org/1.4236/jmp.213.47137 Published Online July 213 (http://www.scirp.org/journal/jmp) An Analysis of Structural and Optical Properties Undoped ZnS and Doped (with Mn, Ni) ZnS Nano Particles Apurba Kr. Das 1*, Apurba Kr. Buzarbaruah 2, Santanu Bardaloi 3 1 Arya Vidyapeeth College, Guwahati, India 2 Dimoria College, Khetri, India 3 Gauhati University, Guwahati, India Email: * akdas9@yahoo.com Received January 2, 213; revised February 4, 213; accepted March 1, 213 Copyright 213 Apurba Kr. Das et al. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited. ABSTRACT The behavior of nano-particles finds a wide application in opto-electronic and semi-conductor devices. ZnS nano-crystals were grown into poly-vinyl alcohol matrix by chemical route at different weight percentage. Optical properties of both un-doped and doped with ZnS nano-crystalline compounds were studied. The nano structure was characterized with the help of X-ray diffraction (XRD) and Hi-resolution Transmission Electron Microscopy (HRTEM). Surface morphology was studied with the help of Scanning Electron Microscopy (SEM). The average particle sizes of ZnS, ZnS-Ni and ZnS-Mn were found to be 6.51, 7.3 and 12 nm respectively in TEM and that obtained from Debye-Scherrer formula is about 2.3 and 2.5 nm for undoped and doped ZnS respectively. Peak of Photo-luminescence (PL) emission spectra was obtained at 375 nm at room temperature and another peak at 433 nm for Ni. Again the peak of Photo-luminescence (PL) emission spectra was obtained at 334 nm at room temperature for Mn, Mn dependant emission was found at 58 nm. These data showed successful doping. PL studies also confirmed presence of dopant in the nano crystallites. Optical absorption studies were carried out with UV-VIS Spectrophotometer and showed a strong absorbance at wavelength 4 nm with a tendency towards blue shift. Selected area electron diffraction (SAED) shows a set of four well defined rings corresponding to diffraction from different planes of the nano crystallites. HRTEM image showed a well crystalline ZnS doped with Ni and Mn. Both Raman spectra and XRD studies confirmed the well crystalline states of ZnS. Keywords: Nano-Particle; PVA; XRD; SEM; TEM; HRTEM; SAED 1. Introduction The physical and chemical properties of nano materials like optical absorbance, fluorescence, catalytic activity, electrical and thermal conductivity etc. are significantly different from the corresponding bulk materials. The special properties of nano particles are due quantum size confinement in nano structure and extremely large surface to volume ratio relative to bulk materials and therefore it is possible to keep high percentage of atoms or molecules in lower reactive boundaries. The synthesis and characterization of nano crystals grown with different chemicals have created interest among the researchers. Low-dimensional semiconductors, like ZnS composite nano-structured have attracted much interest because of their valuable photoluminescence properties [1]. Chemical growth process is a very simple, * Corresponding author. economical, efficient, and convenient method among the various researchers. In optical sensors, electroluminescence devices, digital displays, etc. doped ZnS nano materials are being used extensively. Photo luminescent properties and efficiency of ZnS depend on intrinsic surface states of the particles, and nature of the chemicals treatment employed in their fabrication. Research is also noticed on the application of these types of films in light-emitting materials as well as on their optical properties [2]. The optical light emission in blue-red spectral region is characterized by blue shift at smaller crystallite dimension. We are trying to characterize the properties of ZnS with different doping agents (Ni and Mn) with the help of instrument like X-ray Powder Diffractometer (XRD), Scanning Electron Microscopes (SEM), High Resolution Transmission Electron Microscopes (HRTEM), Photo-luminescence spectrometer (PL), UV visible spectrophotometer (UV-VIS), etc.

A. K. DAS ET AL. 123 Experimental The synthesisation ZnS nano-particles were done by using Polyvinyl Alcohol (PVA) as a matrix. Different weight% solutions of PVA and ZnCl 2 in deionized water were taken and stirred at 2 rpm in a magnetic stirrer at temperature 7 C for 3 hours. The solution was kept overnight for complete dissolution and found to be transparent. A 2 weight% Na 2 S solution was added till the whole solution appears milky. The solution was kept over night inside a dark chamber. As soon as the nanostructure formed, it embedded into the gap. The chemical reaction took place as follows ZnCl Na S ZnS 2NaCl 2 2 To make different % of ZnS:Ni solution, NiCl 2 6H 2 O was mixed by weight% with deionized water. Solution so obtained was mixed with another solution of PVA and ZnCl 2. Then the solution was stirred at 2 rpm in a magnetic stirred at constant temperature 7 C..8 M weight% Na 2 S solution was added to the solution. Precipitation found was washed with deionized water and taken for study. To make different % of ZnS:Mn solution, MnCl 2 4H 2 O was mixed by weight% with deionized water. Solution so obtained was mixed with another solution of PVA and ZnCl 2. Then the solution was stirred at 2 rpm in a magnetic stirrer at constant temperature 7 C..8 M weight% Na 2 S solution was added to the solution. Precipitation found was washed with deionized water and taken for study. 2. Microstructure Studies 2.1. XRD Studies The XRD studies shown in Figures 1 and were obtained from powder. Diffractogram was obtained from a Philips X pert Pro Powder diffractometer using Cu Kα radiation with the operating voltage 4 kv and current 2 ma. The pattern observed was found to be within the nano range [3,4]. XRD patterns revealed the films to be polycrystalline [5]. Planes (111), (22) and (311) were found to present which tallied well with the JCPDS card No. 5-566. The average particle size corresponding to the FWHM was calculated with the Scherrer formulae.94 Dp cos and found to be 2.3 nm [6]. 12 2.2. Electron Diffraction Studies Selected area electron diffraction (SAED) was done with the help of HRTEM. Photo of SAED of undoped ZnS (Figures 2-(c)) also showed a set of three well defined rings corresponding to the planes (111), (22) and (311) in case of undoped ZnS, which is also in good agree- 8 (o %) 7 6 5 4 3 2 1 5 4 3 2 1 (111) (22) (311) 1 2 3 4 5 6 7 8 2 (in Degrees) 1% Mn 1 2 3 4 5 6 7 8 9 1 Figure 1. XRD diffractogram of ZnS; XRD diffractogram of ZnS-Mn. (c) Figure 2. SAED of ZnS; SAED of ZnS-Ni; (c) SAED of ZnS-Mn.

124 A. K. DAS ET AL. ment with that of XRD data. 8 2.3. SEM Studies Photographs of the nano-crystalline thin film were taken with (JEOL, JSM-636) SEM and shown in Figure 3. The surface morphology of the film prepared at 7 C with PVA was observed and found that all the particles formed not exactly spherical. Study showed that the surface of the film was smooth, uniform and without any crack. The particle sizes of ZnS-Ni, ZnS-Mn were found to be 7-16 and 7-15 nm respectively. 7 6 5 4 3 2 1 %.5% Ni 2.4. Photo Luminescence Studies The photo luminescence studies of nano crystalline doped & un-doped (Figure 4) were done at room temperature by using F-25 FL Spectrophotometer. In all the measurement the excitation wavelength was 24 nm. Emission spectra showed a broad peak at 378 nm and another small broad peak at 451 nm for ZnS while 375 nm and 433 nm for ZnZ-Ni (.5%) and at 382 nm for ZnS-Ni. For Mn the emission spectra showed a broad peak at 346 nm and another small broad peak at 468 nm. PL in this region is due to the presence of S vacancies in the lattice. PL spectra of ZnS:Mn thin film revealed yellow-orange emissions. Mn dependent yellow emission was found at 58 nm which was also a confirmation successful Mn doping. Starting with the blue emission (at 468 nm), intensity decreases towards the orange emission (at 58 nm) [7]. PL spectra of ZnS:Ni revealed yellow-orange emissions. 2.5. Optical Absorbance Study The optical absorbance (Figure 5) of ZnS was recorded at room temperature using a Double Beam Automated Spectrophotometer (Hitachi-U321) where the measurement of optical absorbance was done in the range 2-8 nm. The wavelength showed strong absorption. The peak of the absorption showed at 287 nm for ZnS. The peak of the absorption showed blue shift with respect to bulk attributing quantum confinement effect on the nano-particles. Optical absorption studies were carried out with UV-VIS Spectrophotometer and showed a Figure 3. SEM micrograph of ZnS-Ni; ( b) SEM micro- graph of ZnS-Mn. -1 2 3 4 5 6 7 8 Figure 4. PL spectra of Z n-s, ZnS-Ni; PL spectra of Zn-S, ZnS-Mn. strong absorbance at wavelength 4 nm with a tendency towards blue shift. Optical absorbance spectrum of ZnS-Ni (.5%, 1.%) features a strong peak around 4 nm. This spectra of undoped and Ni doped ZnS nano crystal are distinguishable. This indicates that Ni doping has effect on the electronic absorption spectra of ZnS [8]. This may be possible for low doping level. 2.6. HRTEM HRTEM image shows clear lattice fringes of the (1) plane indicating crystal growth along (1) direction. The particle size obtained from HRTEM image is 6 nm and 7.3 nm for ZnS-Ni and ZnS-Mn respectively. 2.7. Raman Studies In Figure 6 the sharp peak of Raman spectra indicated 1 ZnS in well crystalline state. The peaks at 58 cm and 335 cm 1, 347 cm 1 are the characteristic Raman scattering of ZnS and indexed to LO phonon mode [9]. Another

A. K. DAS ET AL. 125 3..45 2.5.4.35.5% Ni Absorbance (a.u) 2. 1.5 1. % Absorbance (a.u.).3.25.2.15.5.1. 2 3 4 5 6 7.5 4 45 5 55 6 2.5 2. Absorbance (a.u) 1.5 1..5.5% Mn 1% Mn. 2 3 4 5 6 (c) 7 8 Figure 5. Absorbance spectra of ZnS; Absorbance spectra of ZnS-Ni; (c) Absorbance spectra of ZnS-Mn. Figure 6. Raman spectra.

126 A. K. DAS ET AL. peak at 264 cm 1 corresponds to TO phonon mode [1] of ZnS. 3. Conclusion ZnS nano crystalline films (un-doped and doped with Ni and Mn) have been synthesized by chemical route. The structural and optical characterization of the films done with the help of XRD, TEM, SEM, SAED, UV-VIS spectrophotometer and PL reveals formation of doped as well as un-doped nano particles. The emission bands at 377 nm, 449 nm (both for %), 375 nm, 433 nm (both for.5% Ni) and 382 nm for may be attributed to impurities or defect state. Similarly the emission bands with respect to 375 nm & 451 nm for ZnS-Mn may be attributed to defect states. The third emission band at 496 nm may be attributed in the 3d shell transition of Mn 2+. The sharp peak of Raman spectra indicated ZnS in well crystalline state which is in good agreement with that obtained from XRD result. 4. Novelty Statement From Photo luminescence study it has been observed that in case of ZnS-Ni, with the increase of doping% (from.5-1.), the intensity of doping related emission spectra is found to be increased. In case of ZnS-Mn, with the increase of doping% (from.5-1.), the intensity found to be increased. It is also observed from the PL that with the increase of doping% (from.5-1.) of both ZnS-Ni and ZnS-Mn, there is blue shift of doping related emission spectra due to quantum confinement effect. The bands with respect to 375 nm & 451 nm may be attributed to defect states. The sharp peaks of Raman spectra indicated ZnS nano particles were in well crystalline state. 5. Acknowledgements The authors are very much thankful to Dr. P. K. Baruah, Department of Chemistry, Gauhati University for his help in taking UV-VIS and PL data. We are also thankful to SAIF, Shillong for providing TEM and SEM facility. Authors are also like to offer their gratitude to SAIF, Guwahati, Department of Instrumentation & USIC, Gauhati University for providing XRD & XRF facility. The authors are also like to offer their heart felt gratitude and thanks to CIF and dept. of Nano-Science and Technology, IITG for providing HRTEM and XRD facility. The authors are also grateful to Prof. K. C. Sarma, Head, Dept. of Instrumentation & USIC, Gauhati University for constant guidance and help. REFERENCES [1] P. Yang, M. Lu, D. Xu, D. Yuan, J. Chang, G. Zhou and M. Pan, Applied Physics A, Vol. 74, pp. 257-259. [2] T. M. Thi, B. H. Van and P. Van Ben, Journal of Nonlinear Optical Physics & Materials, Vol. 19, pp. 237-245. doi:1.1142/s21886351525x [3] B. S. Rema Devi, R. Raveendran and A. V. Vaidyan, Pramana Indian Academy of Sciences, Vol. 68, 27, pp. 679-687. [4] S. Kumar, N. K. Verma and M. L. Singla, Chalcogenide Letters, Vol. 8, 211, pp. 561-569. [5] A. Goudarzi, G. M. Aval, S. S. Park, M.-C. Choi, R. Sahraei, M. Habib Ullah, A. Avane and C.-S. Ha, Chemistry of Materials, Vol. 21, 29, pp. 2375-2385. doi:1.121/cm83329w [6] G. Murugadoss, B. Rajamannan and U. Madhusudhanana, Chalcogenide Letters, Vol. 6, 29, pp. 197-21. [7] S. P. Singh, O. J. Perales-Perez, M. S. Tomar and O. V. Mata, Physica Status Solidi (c), Vol. 1, 24, pp. 811-814. doi:1.12/pssc.234292 [8] K. Jayanthi, S. Chawla, H. Chander and D. Haranath, Journal of Nonlinear Optical Physics and Materials, Vol. 42, 27, p. 976. [9] C. Lan, K. Q. Hong, W. Z. Wang and G. H. Wang, Solid State Communication Solid State Communications, Vol. 125, 23, pp. 455-458. doi:1.116/s38-198(2)914-6 [1] W. G. Nilsen, Physical Review, Vol.182, 1969, pp. 838-85.